Novel zero-current-switching (ZCS) PWM switch cell minimizingadditional conduction loss

This paper proposes a new zero-current-switching (ZCS) pulsewidth modulation (PWM) switch cell that has no additional conduction loss of the main switch. In this cell, the main switch and the auxiliary switch turn on and turn off under zero-current condition. The diodes commutate softly and the reverse-recovery problems are alleviated. The conduction loss and the current stress of the main switch are minimized, since the resonating current for the soft switching does not flow through the main switch. Based on the proposed ZCS PWM switch cell, a new family of DC-to-DC PWM converters is derived. The new family of ZCS PWM converters is suitable for the high-power applications employing insulated gate bipolar transistors. Among the new family of DC-to-DC PWM converters, a boost converter was taken as an example and has been analyzed. Design guidelines with a design example are described and verified by experimental results from the 2.5 kW prototype boost converter operating at 40 kHz     

Zero-voltage switching technique in DC/DC converters

A novel resonant switch operating under the principle of zero-voltage switching is presented. The basic configurations of the voltage-mode resonant switches are presented. The circuit's operating principles are described using a voltage-mode quasi-resonant boost converter. DC analysis of the converter is carried out. A new family of voltage-mode quasi-resonant converters are derived, and several members of this family are presented. The duality relationship between the zero-current switching technique and the zero-voltage switching technique is derived. These two techniques are compared using an example showing the duality between a current-mode quasi-resonant Buck converter and a voltage-mode quasi-resonant boost converter. The similarities and differences of the voltage-mode quasi-resonant converters and the Class-E converters are discussed. A 5 MHz 50 V to 5 V flyback converter employing the zero-voltage switching technique has been implemented. Design considerations and experimental results of this circuit are presented     

A new modulation strategy for a buck-boost input AC/DC converter

This paper presents a novel modulation strategy for a power factor corrected (PFC), isolated AC/DC converter derived from the integration of a nonisolated, two switch buck-boost AC/DC converter with an isolated dual active bridge DC/DC converter (2SBBDAB). This strategy, termed discontinuous leading/trailing edge (DLTE) modulation, serves to maximize the duty cycle of the input switch while keeping the current in the buck-boost inductor discontinuous. Hence, the crest factors of the currents in the switching devices are minimized, the input switch is turned on at zero current and the zero-voltage switching ranges of the bridge switches are unaffected by the integration. A conventional isolated, PFC AC/DC converter typically consists of a boost converter cascaded with a forward converter. The ratings required of the power switching devices of the 2SBBDAB employing the DLTE modulation strategy are similar to those required of the conventional design for wide line voltage operation. However, the 2SBBDAB converter has higher line voltage surge immunity than that of the conventional design and, unlike the conventional design, it has inherent inrush current limiting. The DLTE modulation strategy may be applied to the family of converters composed of the two switch buck-boost integrated with half and full-bridge forward converters     

New family of zero-current-switching PWM converters using a new zero-current-switching PWM auxiliary circuit

A new family of zero-current-switching (ZCS) pulsewidth-modulation (PWM) converters using a new ZCS-PWM auxiliary circuit is presented in this paper. The main switch and auxiliary switch operate at ZCS turn-on and turn-off, and the all-passive semiconductor devices in the ZCS-PWM converters operate at zero-voltage-switching (ZVS) turn-on and turn-off. Besides operating at constant frequency and reducing commutation losses, these new converters have no additional current stress and conduction loss in the main switch in comparison to the hard-switching converter counterpart. The PWM switch model and state-space averaging approach is used to estimate and examine the steady-state and dynamic character of the system. The new family of ZCS-PWM converters is suitable for high-power applications using insulated gate bipolar transistors (IGBTs). The principle of operation, theoretical analysis, and experimental results of the new ZCS-PWM boost converter, rated 1.6 kW and operating at 30 kHz, are provided in this paper to verify the performance of this new family of converters.     

A Comparative Study of Zero-Current-Transition PWM Converters

Zero-current-transition pulsewidth-modulation (ZCT-PWM) boost converters are conventional boost converters that use an active auxiliary circuit to turn off the main power switch with zero-current switching; the operation and properties of these converters are the focus of this paper. In this paper, the general operating principles behind all ZCT-PWM converters are reviewed, and the operation and properties of specific converters are discussed. The strengths and weaknesses of each converter are stated, and a new and improved ZCT-PWM boost converter is proposed and discussed. Experimental results obtained from an experimental ZCT-PWM boost converter prototype implemented with several of the auxiliary circuits discussed in this paper are presented, and the results confirm the superior performance of the proposed converter     

A New Family of Zero-Current-Switching (ZCS) PWM Converters

A new family of zero-current-switching (ZCS) pulsewidth-modulated (PWM) converters which uses a new ZCS-PWM switch cell is presented in this paper. The main switch and auxiliary switch operate at ZCS turn-on and turn-off, and all the passive semiconductor devices in the ZCS-PWM converter operate at zero-voltage-switching (ZVS) turn-on and turn-off. Besides operating at constant frequency and with reduced commutation losses, these new converters have no additional current stress in comparison to the hard-switching converter counterpart. The new family of ZCS-PWM converters is suitable for high-power applications using insulated gate bipolar transistors (IGBTs). The PWM switch model and state-space averaging approach is used to estimate and examine the steady-state and dynamic character of the system. The principle of operation, theoretical analysis, and experimental results of the new ZCS-PWM boost converter, rated 1 kW and operating at 30 kHz, are provided in this paper to verify the performance of this new family of converters.     

A new ZVT-PWM DC-DC converter

In this paper, a new active snubber cell that overcomes most of the drawbacks of the normal "zero voltage transition-pulse width modulation" (ZVT-PWM) converter is proposed to contrive a new family of ZVT-PWM converters. A converter with the proposed snubber cell can also operate at light load conditions. All of the semiconductor devices in this converter are turned on and off under exact or near zero voltage switching (ZVS) and/or zero current switching (ZCS). No additional voltage and current stresses on the main switch and main diode occur. Also, the auxiliary switch and auxiliary diodes are subjected to voltage and current values at allowable levels. Moreover, the converter has a simple structure, low cost, and ease of control. A ZVT-PWM boost converter equipped with the proposed snubber cell is analyzed in detail. The predicted operation principles and theoretical analysis of the presented converter are verified with a prototype of a 2 kW and 50 kHz PWM boost converter with insulated gate bipolar transistor (IGBT). In this study, a design procedure of the proposed active snubber cell is also presented. Additionally, at full output power in the proposed soft switching converter, the main switch loss is about 27% and the total circuit loss is about 36% of that in its counterpart hard switching converter, and so the overall efficiency, which is about 91% in the hard switching case, increases to about 97%     

Novel zero-Voltage-transition PWM DC-DC converters

A new family of zero-voltage-switching (ZVS) pulsewidth-modulated (PWM) converters that uses a new ZVS-PWM switch cell is presented in this paper. Except for the auxiliary switch, all active and passive semiconductor devices in the ZVS-PWM converters operate at ZVS turn ON and turn OFF. The auxiliary switch operates at zero-current-switching (ZCS) turns ON and OFF. Besides operating at constant frequency, these new converters have no overvoltage across the switches and no additional current stress on the main switch in comparison to the hard-switching converter counterpart. Auxiliary components rated at very small current are used. The principle of operation, theoretical analysis, and experimental results of the new ZVS-PWM boost converter, rated 1 kW, and operating at 80 kHz, are provided in this paper to verify the performance of this new family of converters.     

High-Power Density Design of a Soft-Switching High-Power Bidirectional dc–dc Converter

A bidirectional dc-dc converter typically consists of a buck and a boost converters. In order to have high-power density, the converter can be designed to operate in discontinuous conducting mode (DCM) such that the passive inductor can be minimized. The DCM operation associated current ripple can be alleviated by interleaving multiphase currents. However, DCM operation tends to increase turnoff loss because of a high peak current and its associated parasitic ringing due to the oscillation between the inductor and the device output capacitance. Thus, the efficiency is suffered with the conventional DCM operation. Although to reduce the turnoff loss a lossless capacitor snubber can be added across the switch, the energy stored in the capacitor needs to be discharged before device is turned on. This paper adopts a gate signal complimentary control scheme to turn on the nonactive switch and to divert the current into the antiparalleled diode of the active switch so that the main switch can be turned on under zero-voltage condition. This diverted current also eliminates the parasitic ringing in inductor current. For capacitor value selection, there is a tradeoff between turnon and turnoff losses. This paper suggests the optimization of capacitance selection through a series of hardware experiments to ensure the overall power loss minimization under complimentary DCM operating condition. According to the suggested design optimization, a 100-kW hardware prototype is constructed and tested. The experimental results are provided to verify the proposed design approach.     

A new family of zero-voltage-transition PWM converters with dual active auxiliary circuits

A new family of active auxiliary circuits that allow the power switch in single switch, pulsewidth modulated converters to operate with zero-voltage switching is proposed in this paper. The main feature of an auxiliary circuit belonging to this family is that the auxiliary switch can operate with a zero-current switching turn-on and turn-off without increasing the peak current stresses of the main switch. This is an improvement over previous proposed auxiliary circuits where either the auxiliary switch operates with a hard turn-off or the circuit itself increases the peak stresses of the main switch. In this paper, the fundamental principles behind the proposed family of active auxiliary circuits are explained. Based on these principles, an example auxiliary circuit is systematically derived and presented along with several other auxiliary circuits belonging to the new family. The operation of a boost converter operating with the example auxiliary circuit is discussed in detail, and general guidelines for the design and implementation of auxiliary circuits belonging to the new family are given. The feasibility of the example auxiliary circuit is confirmed by experimental results obtained from a 500-W, 100-kHz boost converter laboratory prototype.     

一种新型单管软开关Boost变换器及其EMI研究

分析了一种用于传统Boost变换器的软开关方案。电路中只使用了一个开关管以及最少的元件，但却获得了开关器件零电流开通和零电压关断的效果。文中通过仿真描述了这一电路的运行特点，同时还分析了其与传统硬开关Boost电路的EMI状况差异以及门控电路对该变换器EMI状况的改善效果。     

A zero-voltage-switched PWM boost converter with an energyfeedforward auxiliary circuit

A zero-voltage-switched (ZVS) pulsewidth-modulated (PWM) boost converter with an energy feedforward auxiliary circuit is proposed in this paper. The auxiliary circuit, which is a resonant circuit consisting of a switch and passive components, ensures that the converter's main switch and boost diode operate with soft switching. This converter can function with PWM control because the auxiliary resonant circuit operates for a small fraction of the switching cycle. Since the auxiliary circuit is a resonant circuit, the auxiliary switch itself has both a soft turn on and turn off, resulting in reduced switching losses and electromagnetic interference (EMI). This is unlike other proposed ZVS boost converters with auxiliary circuits where the auxiliary switch has a hard turn off. Peak switch stresses are only slightly higher than those found in a conventional PWM boost converter because part of the energy that would otherwise circulate in the auxiliary circuit and drastically increase peak switch stresses is fed to the load. In this paper, the operation of the converter is explained and analyzed, design guidelines are given, and experimental results obtained from a prototype are presented. The proposed converter is found to be about 2%-3% more efficient than the conventional PWM boost converter     

Novel ZVT-PWM converters with active snubbers

An active snubber cell is proposed to contrive zero-voltage-transition (ZVT) pulsewidth-modulated (ZVT-PWM) converters. Except for the auxiliary switch, all active and passive semiconductor devices in a ZVT-PWM converter operate at zero-voltage-switching (ZVS) turn on and turn off. The auxiliary switch operates at ZVS turn off and near zero current-switching (ZCS) turn on. An analytical study on a boost ZVT-PWM converter with the proposed active snubber cell is presented in detail. A 750 W 80 kHz prototype of the boost ZVT-PWM converter has been built in the laboratory to experimentally verify the analysis. Six basic ZVT-PWM converters can be easily created by attaching the proposed active snubber cells to conventional PWM converters. A detailed design procedure of the proposed active snubber cell is also presented in this paper     

High step-up converter with coupled-inductor

In this study, a high step-up converter with a coupled-inductor is investigated. In the proposed strategy, a coupled inductor with a lower-voltage-rated switch is used for raising the voltage gain (whether the switch is turned on or turned off). Moreover, a passive regenerative snubber is utilized for absorbing the energy of stray inductance so that the switch duty cycle can be operated under a wide range, and the related voltage gain is higher than other coupled-inductor-based converters. In addition, all devices in this scheme also have voltage-clamped properties and their voltage stresses are relatively smaller than the output voltage. Thus, it can select low-voltage low-conduction-loss devices, and there are no reverse-recovery currents within the diodes in this circuit. Furthermore, the closed-loop control methodology is utilized in the proposed scheme to overcome the voltage drift problem of the power source under the load variations. As a result, the proposed converter topology can promote the voltage gain of a conventional boost converter with a single inductor, and deal with the problem of the leakage inductor and demagnetization of transformer for a coupled-inductor-based converter. Some experimental results via examples of a proton exchange membrane fuel cell (PEMFC) power source and a traditional battery are given to demonstrate the effectiveness of the proposed power conversion strategy.     

Modeling PWM DC/DC converters out of basic converter units

An alternative approach to modeling pulsewidth-modulated (PWM) DC/DC converters out of basic converter units (BCUs) is presented in this paper. Typical PWM DC/DC converters include the well-known buck, boost, buck-boost, Cuk, Zeta, and Sepic. With proper reconfiguration, these converters can be represented in terms of either buck or boost converter and linear devices, thus, the buck and boost converters are named BCUs. The PWM converters are, consequently, categorized into buck and boost families. With this categorization, the small-signal models of these converters are readily derived in terms of h parameter (for buck family) and g parameter (for boost family). Using the proposed approach, not only can one find a general configuration for converters in a family, but one can yield the same small-signal models as those derived from the direct state-space averaging method. Additionally, modeling of quasi-resonant converters and multiresonant converters can be simplified when adopting the proposed approach     

A Current-Controlled Tristate Boost Converter With Improved Performance Through RHP Zero Elimination

A novel current mode control scheme for the tristate boost converter circuit is proposed, which eliminates the zero in the right-half plane (RHP), and improves the dynamic performance. The tristate boost converter contains an additional switch across the inductor. Within a clock cycle, the inductor current first rises during the on interval of the main switch, then falls during the off or capacitor charging interval, and finally, remains almost constant during the freewheeling interval when the additional switch is turned on. In the proposed controller, the peak value of the inductor current is controlled by peak current mode control using an outer voltage feedback loop, whereas the freewheeling current is controlled by the input voltage and the reference voltage feedforward path. Applying both feedback as well as feedforward control on the inductor current significantly improves the output voltage regulation, audio susceptibility, and transient responses. We show that the RHP zero is completely eliminated from the closed-loop control-to-output transfer function. This results in a very large bandwidth, and hence a superior dynamic performance. The latter is established by comparison with the voltage-mode- and current-mode-controlled classical boost converters that suffer from the RHP zero problem, as well as with other tristate boost converter control techniques like the constant charging interval and dual mode control, recently proposed in the literature. Significant superiority of the proposed scheme is established both through simulation and experimentation.     

A new ZVT-ZCT-PWM DC-DC converter

In this paper, a new active snubber cell is proposed to contrive a new family of pulse width modulated (PWM) converters. This snubber cell provides zero voltage transition (ZVT) turn on and zero current transition (ZCT) turn off together for the main switch of a converter. Also, the snubber cell is implemented by using only one quasi resonant circuit without an important increase in the cost and complexity of the converter. New ZVT-ZCT-PWM converter equipped with the proposed snubber cell provides most the desirable features of both ZVT and ZCT converters presented previously, and overcomes most the drawbacks of these converters. Subsequently, the new converter can operate with soft switching successfully at very wide line and load ranges and at considerably high frequencies. Moreover, all semiconductor devices operate under soft switching, the main devices do not have any additional voltage and current stresses, and the stresses on the auxiliary devices are at low levels. Also, the new converter has a simple structure, low cost and ease of control. In this study, a detailed steady state analysis of the new converter is presented, and this theoretical analysis is verified exactly by a prototype of a 1-kW and 100-kHz boost converter.     

Switch failure diagnosis based on inductor current observation for boost converters

Face to the growing number of applications using DC–DC power converters, the improvement of their reliability is subject to an increasing number of studies. Especially in safety critical applications, designing fault-tolerant converters is becoming mandatory. In this paper, a switch fault-tolerant DC–DC converter is studied. First, some of the fastest Fault Detection Algorithms (FDAs) are recalled. Then, a fast switch FDA is proposed which can detect both types of failures; open circuit fault as well as short circuit fault can be detected in less than one switching period. Second, a fault-tolerant converter which can be reconfigured under those types of fault is introduced. Hardware-In-the-Loop (HIL) results and experimental validations are given to verify the validity of the proposed switch fault-tolerant approach in the case of a single switch DC–DC boost converter with one redundant switch.     

Zero-Voltage-Transition PWM Converters With Synchronous Rectifier

In this paper, a family of zero-voltage-transition (ZVT) pulsewidth-modulated converters with synchronous rectifier (SR) is introduced. The SR decreases the conduction losses, while it increases the achieved soft switching range. In this family of converters, zero-voltage-switching (ZVS) condition is attained for the main and rectifier switches. Also, zero-current switching is achieved for the auxiliary switch. In addition, the applied ZVS technique can eliminate the reverse recovery losses of the rectifier switch body diode. The ZVT buck converter with SR is analyzed, and the presented experimental results confirm the theoretical analysis.      

Design and analysis of a novel zero-voltage-transition interleaved boost converter for renewable power applications

High-efficiency stepping up operation is an important feature of the converters used in renewable power applications due to the low voltage level of photo-voltaic arrays and fuel cells. Decreasing the switching losses of the converters is an effective solution for increasing the converter efficiency, especially in high-power applications. This article presents a novel zero-voltage-transition (ZVT) interleaved dc–dc boost converter that can be used in renewable power sources to reduce switching losses. The auxiliary circuit used in the proposed converter is composed of only one auxiliary switch and a minimum number of passive components without an important increase in the cost and complexity. The main advantage of the proposed converter is that it not only provides ZVT in the boost switches but also provides soft switching in the auxiliary switch. Another advantage of the proposed topology is that the semiconductor devices used in the converter do not have any additional voltage or current stresses. Also, it has a simple structure, low cost and ease of control. In this article, a detailed steady-state analysis of the proposed converter is presented. The theoretical analysis is verified via simulation and experimental studies which are in very good agreement.