Electrical characteristics of 8-/spl Aring/ EOT HfO/sub 2//TaN low thermal-budget n-channel FETs with solid-phase epitaxially regrown junctions

The authors demonstrate high-performing n-channel transistors with a HfO/sub 2//TaN gate stack and a low thermal-budget process using solid-phase epitaxial regrowth of the source and drain junctions. The thinnest devices have an equivalent oxide thickness (EOT) of 8 /spl Aring/, a leakage current of 1.5 A/cm/sup 2/ at V/sub G/=1 V, a peak mobility of 190 cm/sup 2//V/spl middot/s, and a drive-current of 815 /spl mu/A//spl mu/m at an off-state current of 0.1 /spl mu/A//spl mu/m for V/sub DD/=1.2 V. Identical gate stacks processed with a 1000-/spl deg/C spike anneal have a higher peak mobility at 275 cm/sup 2//V/spl middot/s, but a 5-/spl Aring/ higher EOT and a reduced drive current at 610 /spl mu/A//spl mu/m. The observed performance improvement for the low thermal-budget devices is shown to be mostly related to the lower EOT. The time-to-breakdown measurements indicate a maximum operating voltage of 1.6 V (1.2 V at 125 /spl deg/C) for a ten-year lifetime, whereas positive-bias temperature-instability measurements indicate a sufficient lifetime for operating voltages below 0.75 V.     

Design and fabrication of RESURF MOSFETs on 4H-SiC(0001), (112~0), and 6H-SiC(0001)

Design and fabrication of lateral SiC reduced surface field (RESURF) MOSFETs have been investigated. The doping concentration (dose) of the RESURF and lightly doped drain regions has been optimized to reduce the electric field crowding at the drain edge or in the gate oxide by using device simulation. The optimum oxidation condition depends on the polytype: N/sub 2/O oxidation at 1300/spl deg/C seems to be suitable for 4H-SiC, and dry O/sub 2/ oxidation at 1250/spl deg/C for 6H-SiC. The average inversion-channel mobility is 22, 78, and 68 cm/sup 2//Vs for 4H-SiC(0001), (112~0), and 6H-SiC(0001) MOSFETs, respectively. RESURF MOSFETs have been fabricated on 10-/spl mu/m-thick p-type 4H-SiC(0001), (112~0), and 6H-SiC(0001) epilayers with an acceptor concentration of 1/spl times/10/sup 16/ cm/sup -3/. A 6H-SiC(0001) RESURF MOSFET with a 3-/spl mu/m channel length exhibits a high breakdown voltage of 1620 V and an on-resistance of 234 m/spl Omega//spl middot/cm/sup 2/. A 4H-SiC(112~0) RESURF MOSFET shows the characteristics of 1230 V-138 m/spl Omega//spl middot/cm/sup 2/.     

High performance quantum dot lasers on GaAs substrates operating in 1.5 /spl mu/m range

Stacked InAs/InGaAs quantum dots are used as an active media of metamorphic InGaAs-InGaAlAs lasers grown on GaAs substrates by molecular beam epitaxy. High quantum efficiency (/spl eta//sub i/>60%) and low internal losses (/spl alpha/<3-4 cm/sup -1/) are realised. The transparency current density per single QD layer is estimated as /spl sim/70 A/cm/sup 2/ and the characteristic temperature is 60 K (20-85/spl deg/C). The emission wavelength exceeds 1.51 /spl mu/m at temperatures above 60/spl deg/C.     

4H-SiC power bipolar junction transistor with a very low specific ON-resistance of 2.9 m/spl Omega//spl middot/cm/sup 2/

This letter reports a newly achieved best result on the specific ON-resistance (R/sub SP/spl I.bar/ON/) of power 4H-SiC bipolar junction transistors (BJTs). A 4H-SiC BJT based on a 12-/spl mu/m drift layer shows a record-low specific-ON resistance of only 2.9 m/spl Omega//spl middot/cm/sup 2/, with an open-base collector-to-emitter blocking voltage (V/sub ceo/) of 757 V, and a current gain of 18.8. The active area of this 4H-SiC BJT is 0.61 mm/sup 2/, and it has a fully interdigitated design. This high-performance 4H-SiC BJT conducts up to 5.24 A at a forward voltage drop of V/sub CE/=2.5 V, corresponding to a low R/sub SP-ON/ of 2.9 m/spl Omega//spl middot/cm/sup 2/ up to J/sub c/=859 A/cm/sup 2/. This is the lowest specific ON-resistance ever reported for high-power 4H-SiC BJTs.     

A CMOS voltage reference based on weighted /spl Delta/V/sub GS/ for CMOS low-dropout linear regulators

A CMOS voltage reference, which is based on the weighted difference of the gate-source voltages of an NMOST and a PMOST operating in saturation region, is presented. The voltage reference is designed for CMOS low-dropout linear regulators and has been implemented in a standard 0.6-/spl mu/m CMOS technology (V/sub thn//spl ap/|V/sub thp/|/spl ap/0.9 V at 0/spl deg/C). The occupied chip area is 0.055 mm/sup 2/. The minimum supply voltage is 1.4 V, and the maximum supply current is 9.7 /spl mu/A. A typical mean uncalibrated temperature coefficient of 36.9 ppm//spl deg/C is achieved, and the typical mean line regulation is /spl plusmn/0.083%/V. The power-supply rejection ratio without any filtering capacitor at 100 Hz and 10 MHz are -47 and -20 dB, respectively. Moreover, the measured noise density with a 100-nF filtering capacitor at 100 Hz is 152 nV//spl radic/(Hz) and that at 100 kHz is 1.6 nV//spl radic/(Hz).     

10-kV, 123-m/spl Omega//spl middot/cm/sup 2/ 4H-SiC power DMOSFETs

10-kV, 123-m/spl Omega//spl middot/cm/sup 2/ power DMOSFETs in 4H-SiC are demonstrated. A 42% reduction in R/sub on,sp/, compared to a previously reported value, was achieved by using an 8 /spl times/ 10/sup 14/ cm/sup -3/ doped, 85-/spl mu/m-thick drift epilayer. An effective channel mobility of 22 cm/sup 2//Vs was measured from a test MOSFET. A specific on-resistance of 123 m/spl Omega//spl middot/cm/sup 2/ were measured with a gate bias of 18 V, which corresponds to an E/sub ox/ of 3 MV/cm. A leakage current of 197 /spl mu/A was measured at a drain bias of 10 kV from a 4H-SiC DMOSFET with an active area of 4.24 /spl times/ 10/sup -3/ cm/sup 2/. A switching time of 100 ns was measured in 4.6-kV, 1.3-A switching measurements. This shows that the 4H-SiC power DMOSFETS are ideal for high-voltage, high-speed switching applications.     

A high current gain 4H-SiC NPN power bipolar junction transistor

This work reports the development of high power 4H-SiC bipolar junction transistors (BJTs) by using reduced implantation dose for p+ base contact region and annealing in nitric oxide of base-to-emitter junction passivation oxide for 2 hours at 1150/spl deg/C. The transistor blocks larger than 480 V and conducts 2.1 A (J/sub c/=239 A/cm/sup 2/) at V/sub ce/=3.4 V, corresponding to a specific on-resistance (R/sub sp on/) of 14 m/spl Omega/cm/sup 2/, based on a drift layer design of 12 /spl mu/m doped to 6/spl times/10/sup 15/cm/sup -3/. Current gain /spl beta//spl ges/35 has been achieved for collector current densities ranging from J/sub c/=40 A/cm/sup 2/ to 239 A/cm/sup 2/ (I/sub c/=2.1 A) with a peak current gain of 38 at J/sub c/=114 A/cm/sup 2/.     

1000-V, 30-A 4H-SiC BJTs with high current gain

This paper presents the development of 1000 V, 30A bipolar junction transistor (BJT) with high dc current gain in 4H-SiC. BJT devices with an active area of 3/spl times/3 mm/sup 2/ showed a forward on-current of 30 A, which corresponds to a current density of 333 A/cm/sup 2/, at a forward voltage drop of 2 V. A common-emitter current gain of 40, along with a low specific on-resistance of 6.0m/spl Omega//spl middot/cm/sup 2/ was observed at room temperature. These results show significant improvement over state-of-the-art. High temperature current-voltage characteristics were also performed on the large-area bipolar junction transistor device. A collector current of 10A is observed at V/sub CE/=2 V and I/sub B/=600 mA at 225/spl deg/C. The on-resistance increases to 22.5 m/spl Omega//spl middot/cm/sup 2/ at higher temperatures, while the dc current gain decreases to 30 at 275/spl deg/C. A sharp avalanche behavior was observed at a collector voltage of 1000 V. Inductive switching measurements at room temperature with a power supply voltage of 500 V show fast switching with a turn-off time of about 60 ns and a turn-on time of 32 ns, which is a result of the low resistance in the base.     

High-performance singlemode InGaNAs/GaAs laser

Performance characteristics of an InGaNAs/GaAs ridge-waveguide in-plane laser diode, which is grown by molecular beam epitaxy, are reported. The laser emits at a wavelength of 1.262 /spl mu/m in a single lateral mode, launching an output up to 240 mW at 20/spl deg/C and 20 mW at 120/spl deg/C. The threshold is 15 mA at 20/spl deg/C, corresponding to a threshold current density of 313 A/cm/sup 2/.     

Analysis of transit times and minority carrier mobility in n-p-n 4H-SiC bipolar junction transistors

An analysis of the transit times and minority carrier mobility in n-p-n 4H-SiC RF bipolar junction transistors is presented. These parameters were extracted from small signal RF measurements on 4H-SiC RF transistors with three different base thicknesses: 100, 140, and 200 nm. The study shows that the room temperature minority carrier electron mobility is 215 cm/sup 2//V/spl middot/s for a base Al doping of N/sub B/=4/spl times/10/sup 18/ cm/sup -3/. The analysis reveals that the collector charging time /spl tau//sub C/ and the parasitic charging time /spl tau//sub P/ from the capacitance between metal pads and the underlying collector region have a significant effect on the transistors RF performance. The calculated RF gain is in good agreement with the measured results.     

Continuous-wave operation of quantum cascade laser emitting near 5.6 /spl mu/m

Buried heterostructure quantum cascade lasers emitting at 5.64 /spl mu/m are presented. Continuous-wave (CW) operation has been achieved at -30/spl deg/C for junction down mounted devices with both facets coated. A 750 /spl mu/m-long laser exhibited 3 mW of CW power with a threshold current density of 5.4 kA/cm/sup 2/.     

Top-gate TFTs using 13.56 MHz PECVD microcrystalline silicon

Top-gate thin-film transistors (TFTs) with microcrystalline silicon (/spl mu/c-Si) channel layers deposited using standard 13.56 MHz plasma-enhanced chemical vapor deposition were fabricated at a maximum processing temperature of 250/spl deg/C. The TFTs employ amorphous silicon nitride (a-SiN) as the gate dielectric layer. The 80-nm-thick /spl mu/c-Si channel layer showed a dark conductivity of the order of 10/sup -7/ S/cm and a crystalline volume fraction of over 80%. The /spl mu/c-Si TFTs showed a field effect mobility of 0.85 cm/sup 2//V/spl middot/s, a threshold voltage of 4.8 V, a subthreshold slope of 1 V/dec, and an ON/OFF current ratio of /spl sim/10/sup 7/. More importantly, the TFTs were very stable under gate bias stress, offering promise for organic light-emitting display (OLED) applications.     

Thermally stable Ge/Ag/Ni Ohmic contact for InAlAs/InGaAs/InP HEMTs

Excellent annealed ohmic contacts based on Ge/Ag/Ni metallization have been realized in a temperature range between 385 and 500/spl deg/C, with a minimum contact resistance of 0.06 /spl Omega//spl middot/mm and a specific contact resistivity of 2.62 /spl times/10/sup -7/ /spl Omega//spl middot/cm/sup 2/ obtained at an annealing temperature of 425/spl deg/C for 60 s in a rapid thermal annealing (RTA) system. Thermal storage tests at temperatures of 215 and 250/spl deg/C in a nitrogen ambient showed that the Ge/Ag/Ni based ohmic contacts with an overlay of Ti/Pt/Au had far superior thermal stabilities than the conventional annealed AuGe/Ni ohmic contacts for InAlAs/InGaAs high electron mobility transistors (HEMTs). During the storage test at 215/spl deg/C, the ohmic contacts showed no degradation after 200 h. At 250/spl deg/C, the contact resistance value of the Ge/Ag/Ni ohmic contact increased only to a value of 0.1 /spl Omega//spl middot/mm over a 250-h period. Depletion-mode HEMTs (D-HEMTs) with a gate length of 0.2 /spl mu/m fabricated using Ge/Ag/Ni ohmic contacts with an overlay of Ti/Pt/Au demonstrated excellent dc and RF characteristics.     

High-power P-i-N diode with local lifetime control using palladium diffusion controlled by radiation defects

We demonstrate for the first time a high-power P-i-N diode with local lifetime control using palladium (Pd) diffusion. Low-temperature (600/spl deg/C-700/spl deg/C) diffusion of Pd is stimulated by radiation defects resulting from alpha-particle irradiation (/sup 4/He/sup 2+/: 10 MeV, 10/sup 12/ cm/sup -2/). The region of maximal radiation damage of Gaussian shape is decorated by substitutional Pd after diffusion from a palladium silicide surface layer through the P/sup +/--P region into the N-base close to the anode junction. Significantly lower leakage current compared to that of standard /sup 4/He/sup 2+/ irradiation and very good ruggedness under fast recovery (di/dt/spl ap/500 A//spl mu/s, V/sub R//spl ap/2 kV) is demonstrated for Pd diffusion at 600/spl deg/C.     

Minimal group refractive index dispersion and gain evolution in ultra-broad-band quantum cascade lasers

The group refractive index dispersion in ultra-broad-band quantum cascade (QC) lasers has been determined using Fabry-Perot spectra obtained by operating the lasers in continuous wave mode below threshold. In the wavelength range of 5-8 /spl mu/m, the global change of the group refractive index is as small as +8.2 /spl times/ 10/sup -3/ /spl mu/m/sup -1/. Using the method of Hakki and Paoli (1975), the subthreshold gain of the lasers has furthermore been measured as a function of wavelength and current. At the wavelength of best performance, 7.4 /spl mu/m, a modal gain coefficient of 16 cm/spl middot/kA/sup -1/ at threshold and a waveguide loss of 18 cm/sup -1/ have been estimated. The gain evolution confirms an earlier assumption that cross-absorption restricted laser action to above 6 /spl mu/m wavelength.     

A transmit/receive IF chip set for WCDMA mobiles in 0.35 /spl mu/m CMOS

An implementation of the IF section of WCDMA mobile transceivers with a set of two chips fabricated in an inexpensive 0.35-/spl mu/m two-poly three-metal CMOS process is presented. The transmit/receive chip set integrates quadrature modulators and demodulators, wide dynamic range automatic gain control (AGC) amplifiers, with linear-in-decibel gain control, and associated circuitry. This paper describes the problems encountered and the solutions envisaged to meet stringent specifications, with process and temperature variations, thus overcoming the limitations of CMOS devices, while operating at frequencies in the range of 100 MHz-1 GHz. Detailed measurement results corroborating successful application of the new techniques are reported. A receive AGC dynamic range of 73 dB with linearity error of less than /spl plusmn/2 dB and spread of less than 5 dB for a temperature range of -30/spl deg/C to +85/spl deg/C in the gain control characteristic has been measured. The modulator measurement shows a carrier suppression of 35 dB and sideband/third harmonic suppression of over 46 dB. The core die area of each chip is 1.5 mm/sup 2/.     

Room temperature performance of low threshold 1.34-1.44-/spl mu/m GaInNAs-GaAs quantum-well lasers grown by molecular beam epitaxy

Room temperature lasing emission at 1.338 and 1.435 /spl mu/m with threshold current densities of 1518 and 1755 A/cm/sup 2/, respectively, is obtained in broad area GaInNAs-GaAs laser diodes (LDs) grown by molecular beam epitaxy. The 1.338-/spl mu/m LDs show a power output per facet up to 0.20 W/A, a characteristic temperature (T/sub 0/) of 78 K, and an external transparency current density (J/sub tr/) of 0.77 kA/cm/sup 2/. Increasing the lasing wavelength to 1.435 /spl mu/m results in a larger J/sub tr/ of 1.16 kA/cm/sup 2/ and a lower T/sub 0/ of 62 K, due to larger nonradiative recombination. However, the 1.435-/spl mu/m LDs still display a power output per facet up to 0.15 W/A, and a high internal quantum efficiency of 52%. These improved performances are achieved without the need to use strain compensation layers, Sb as a surfactant during the quantum-well growth, or a postgrowth thermal anneal cycle.     

Peripheral-coupled-waveguide MQW electroabsorption modulator for near transparency and high spurious free dynamic range RF fiber-optic link

Peripheral coupled waveguide (PCW) design has been deployed in InGaAsP multiple quantum-well (MQW) electroabsorption modulator (EAM) at 1.55-/spl mu/m wavelength. PCW enhances the optical saturation power and reduces the optical insertion loss and the equivalent V/sub /spl pi// simultaneously. A radio-frequency link using a 1.3-mm-long lumped-element PCW EAM has achieved experimentally a link gain of -3 dB, at 500 MHz and at input optical power of 80 mW. The corresponding two-tone multioctave spurious-free dynamic range (SFDR) at the same bias is measured at 118 dB/spl middot/Hz/sup 2/3/. The single-octave SFDR at the third-order null bias is 132 dB/spl middot/Hz/sup 4/5/.     

Fabrication and characterization of 11-kV normally off 4H-SiC trenched-and-implanted vertical junction FET

This letter reports the first demonstration of 101 kV trenched-and-implanted normally off 4H-SiC vertical junction field-effect transistor (TI-VJFET) with a 120 /spl mu/m /spl sim/4.9/spl times/10/sup 14/ cm/sup -3/-doped drift layer. Blocking voltages (V/sub B/) of 10 kV to 11 kV have been measured. The best specific on-resistance (R/sub SP/_/sub ON/) normalized to source active area has been determined to be 130 m/spl Omega//spl middot/cm/sup 2/. Three-dimensional computer modeling including current spreading effect shows that the TI-VJFET would have a specific resistance of 168 m/spl Omega//spl middot/cm/sup 2/ if it is scaled up substantially in size.     

Design, fabrication, and characterization of low forward drop, low leakage, 1-kV 4H-SiC JBS rectifiers

The 1-kV 4H-SiC planar junction barrier Schottky (JBS) rectifiers were designed, fabricated, and characterized. Different p+ implantation dosages and activation anneal methods were used to determine an optimum baseline process. Using the optimized process, the forward drop of our JBS rectifiers is <1.5 V while the reverse leakage current density is <1/spl times/10/sup -5/ A/cm/sup -2/. Blocking voltage>1 kV was achieved using a single-zone junction termination extension termination. It was shown experimentally that 4-/spl mu/m p-type implantation window spacing gives an optimum tradeoff between forward drop voltage and leakage current density for these rectifiers, yielding a specific on-resistance of 3 m/spl Omega//spl middot/cm/sup 2/.