超临界水堆系统分析程序的改进

针对超临界水堆特殊的水物性参数和独立的慢化剂通道设计,对堆芯计算程序PARCS和热工水力程序RELAP5进行了适应性改造。使用改造后的耦合程序PARCS/RELAP5分析了美国超临界水冷参考堆,发现了慢化剂逆向流动和最高功率组件不同于最高外表面包层温度组件的现象,根据这些经验,对中国的超临界水堆分析程序的改进和研发提出了相关意见。     

Analysis of the Peach Bottom flow stability test number 3 using the coupled RELAP5/PARCS code

Nowadays, the coupled codes technique, which consists in incorporating three-dimensional (3D) neutron modeling of the reactor core into system codes, is extensively used for carrying out best estimate (BE) simulation of complex transient in nuclear power plants (NPP). This technique is particularly suitable for transients that involve core spatial asymmetric phenomena and strong feedback effects between core neutronics and reactor loop thermal-hydraulics. Such complex interactions are encountered under normal and abnormal operating conditions of a boiling water reactors (BWR). In such reactors Oscillations may take place owing to the dynamic behavior of the liquid-steam mixture used for removing the thermal power. Therefore, it is necessary to be able to detect in a reliable way these oscillations. The purpose of this work is to characterize one aspect of these unstable behaviors using the coupled codes technique. The evaluation is performed against Peach Bottom-2 low-flow stability tests number 3 using the coupled RELAP5/PARCS code. In this transient dynamically complex neutron kinetics coupling with thermal-hydraulics events take place in response to a core pressure perturbation. The calculated coupled code results are herein assessed and compared against the available experimental data.     

Thermal hydraulic analysis of the IPR-R1 TRIGA research reactor using a RELAP5 model

The RELAP5 code is widely used for thermal hydraulic studies of commercial nuclear power plants. Current investigations and code adaptations have demonstrated that the RELAP5 code can be also applied for thermal hydraulic analysis of nuclear research reactors with good predictions. Therefore, as a contribution to the assessment of RELAP5/MOD3.3 for research reactors analysis, this work presents steady-state and transient calculation results performed using a RELAP5 model to simulate the IPR-R1 TRIGA research reactor at 50 kilowatts (kW) of power operation. The reactor is located in the Nuclear Technology Development Center (CDTN), Brazil. It is a 250 kW, light water moderated and cooled, graphite-reflected, open pool type research reactor. The development and the assessment of a RELAP5 model for the IPR-R1 TRIGA are presented. Experimental data were considered in the process of the RELAP5 model validation. The RELAP5 results were also compared with calculated data from the STHIRP-1 (Research Reactors Thermal Hydraulic Simulation) code. The results obtained have shown that the RELAP5 model for the IPR-R1 TRIGA reproduces the actual steady-state reactor behavior in good agreement with the available data.     

Analyses of the V1000CT-1 benchmark with the DYN3D/ATHLET and DYN3D/RELAP coupled code systems including a coolant mixing model validated against CFD calculations

Plant-measured data provided within the specification of the OECD/NEA VVER-1000 coolant transient benchmark (V1000CT) were used to validate the DYN3D/RELAP5 and DYN3D/ATHLET coupled code systems. Phase 1 of the benchmark (V1000CT-1) refers to the MCP (main coolant pump) switching on experiment conducted in the frame of the plant-commissioning activities at the Kozloduy NPP Unit 6 in Bulgaria. The experiment was started at the beginning of cycle (BOC) with average core expose of 30.7 effective full power days (EFPD), when the reactor power was at 27.5% of the nominal level and three out of four MCPs were operating. The transient is characterized by a rapid increase in the primary coolant flow through the core and, as a consequence, a decrease of the space-dependent core inlet temperature. Both DYN3D/RELAP5 and DYN3D/ATHLET analyses were based on the same reactor model, including identical MCP characteristics, boundary conditions, benchmark-specified nuclear data library and nearly identical nodalization schemes. For an adequate modelling of the redistribution of the coolant flow in the reactor pressure vessel during the transient a simplified mixing model for the DYN3D/ATHLET code was developed and validated against a computational fluid dynamics calculation.

The results of both coupled code calculations are in good agreement with the available experimental data. The discrepancies between experimental data and the results of both coupled code calculations do not exceed the accuracy of the measurement data. This concerns the initial steady-state data as well as the time histories during the transient. In addition to the validation of the coupled code systems against measured data, a code-to-code comparison between simulation results has been performed to evaluate relevant thermal hydraulic models of the system codes RELAP5 and ATHLET and to explain differences between the calculation results.     

RELAP5与CFX程序耦合研究

以RELAP5与CFX程序为基础,利用并行虚拟机技术和CFX用户函数进行编程,开发了RELAP5/CFX耦合程序。在单相范围内,首先利用水平圆管喷放问题验证了程序间耦合的正确性。然后,针对双T型接管混合实验进行了模拟,相对于单独的RELAP5程序,耦合程序能更好地揭示真实的物理现象。通过后续的开发完善,耦合程序可用于反应堆安全分析中存在着显著三维混合现象的问题。     

RELAP5-3D code validation in the neutron-dynamic analysis of transient processes taking place in RBMK-1500 reactors

The paper presents an evaluation of RELAP5-3D code suitability to model-specific transients that take place during RBMK-1500 reactor operation, where the neutronic response of the core is important. Certain RELAP5-3D transient calculation results were benchmarked against calculation results obtained using the Russian complex neutronic-thermal-hydraulic code STEPAN/KOBRA, specially designed for RBMK reactor analysis. Comparison of the results obtained, using the RELAP5-3D and STEPAN/KOBRA codes, showed reasonable mutual agreement of the calculation results of both codes and their reasonable agreement with the real plant data.     

RELAP5/FLUENT耦合程序的开发

热工水力数值模拟是反应堆系统设计和安全分析的重要内容,以RELAP5为代表的系统程序可对瞬态或事故工况进行快速分析,同时以FLUENT为代表的计算流体动力学(CFD)程序对堆芯局部三维现象的分析也越来越重要。为综合利用两者的优点,以RELAP5/FLUENT为基础,利用对RELAP5程序源代码的二次开发和FLUENT的用户自定义函数(UDF)进行编程,开发了RELAP5/FLUENT耦合程序。利用flibe熔盐在水平圆管流动问题验证了程序耦合的正确性;针对2 MW熔盐堆进行了稳态模拟,耦合程序能详细分析熔盐堆的热工水力行为;模拟了2 MW熔盐堆功率突变的瞬态热工水力行为,相对于单独的RELAP5,耦合程序能更好地揭示熔盐堆系统和堆芯的三维物理现象。该耦合程序可用于解决熔盐堆热工水力分析中存在的显著三维混合现象的问题。     

Assessment of a RELAP5 model for the IPR-R1 TRIGA research reactor

RELAP5 code was developed at the Idaho National Environmental and Engineering Laboratory and it is widely used for thermal hydraulic studies of commercial nuclear power plants and, currently, it has been also applied for thermal hydraulic analysis of nuclear research systems with good predictions. This work is a contribution to the assessment of RELAP5/3.3 code for research reactors analysis. It presents steady-state and transient calculation results performed using a RELAP5 model to simulate the IPR-R1 TRIGA research reactor conditions operating at 50 and 100 kW. The reactor is located at the Nuclear Technology Development Centre (CDTN), Brazil. The development and the assessment of a RELAP5 model for the IPR-R1 TRIGA are presented. Experimental data were considered in the process of code-to-data validation. The RELAP5 results were also compared with calculation performed using the STHIRP-1 (Research Reactors Thermal Hydraulic Simulation) code. The use of a cross flow model has been essential to improve results in the transient condition respect to preceding investigations.     

RELAP5铅铋快堆模型拓展及验证

为研究铅铋快堆瞬态热工水力特性,对RELAP5程序进行二次开发,添加铅铋合金（LBE）物性模型和液态金属流动换热模型,并与NACIE-UP和CIRCE-ICE台架的实验结果进行对比。计算结果表明：NACIE-UP台架稳态流量和温度相对误差在2%以内,瞬态相对误差不超过5%,与其他系统程序CATHARE、ATHLET、RELAP5-3D、RELAP5/MOD3.3(modified)相比,本文程序的相对偏差不超过10%;CIRCE-ICE台架稳态流量和温度相对误差在2%以内,瞬态相对误差不超过10%。本文程序满足反应堆系统热工水力分析程序精度要求,可作为铅铋快堆安全分析的有效工具。     

压水堆核电站堆芯物理/热工水力耦合特性研究

采用RELAP5-HD作为堆芯耦合计算程序,以秦山核电二期工程反应堆堆芯为研究对象,建立堆芯活性区的物理/热工水力耦合模型,在此基础上进行了稳态计算和掉棒事故仿真研究。结果表明,使用RELAP5-HD计算得到的结果与电厂实测值符合较好,获得的掉棒事故参数曲线能准确反映事故工况下的参数变化趋势。稳态和事故工况的计算结果均符合堆芯物理/热工水力反馈效应的理论分析,证实了所建立的堆芯耦合模型的准确性,为下一步进行核电站系统的仿真分析提供基础。     

Calculation of the VVER-1000 coolant transient benchmark using the coupled code systems DYN3D/RELAP5 and DYN3D/ATHLET

Plant-measured data provided by the OECD/NEA VVER-1000 coolant transient benchmark programme were used to validate the DYN3D/RELAP5 and DYN3D/ATHLET coupled code systems. Phase 1 of the benchmark (V1000CT-1) refers to an experiment that was conducted during the commissioning of the Kozloduy NPP Unit 6 in Bulgaria. In this experiment, the fourth main coolant pump was switched on whilst the remaining three were running normal operating conditions. The experiment was conducted at 27.5% of the nominal level of the reactor power. The transient is characterized by a rapid increase in the primary coolant flow through the core, and as a consequence, a decrease of the space-dependent core inlet temperature. The control rods were kept in their original positions during the entire transient. The coupled simulations performed on both DYN3D/RELAP5 and DYN3D/ATHLET were based on the same reactor model, including identical main coolant pump characteristics, boundary conditions, benchmark-specified nuclear data library and nearly identical nodalization schemes. In addition to validation of the coupled code systems against measured data, a code-to-code comparison between simulation results has also been performed to evaluate the respective thermal hydraulic models of the system codes RELAP5 and ATHLET.     

A coupled RELAP5-3D/CFD methodology with a proof-of-principle calculation

The RELAP5-3D computer code was modified to make the explicit coupling capability in the code fully functional. As a test of the modified code, a coupled RELAP5/RELAP5 analysis of the Edwards–O'Brien blowdown problem was performed which showed no significant deviations from the standard RELAP5-3D predictions. In addition, a multiphase Computational Fluid Dynamics (CFD) code was modified to permit explicit coupling to RELAP5-3D. Several calculations were performed with this code. The first analysis used the experimental pressure history from a point just upstream of the break as a boundary condition. This analysis showed that a multiphase CFD code could calculate the thermodynamic and hydrodynamic conditions during a rapid blowdown transient. Finally, a coupled RELAP5/CFD analysis was performed. The results are presented in this paper.     

Simulation of a main steam line break accident using a coupled “system thermal-hydraulics,three-dimensional reactor kinetics,and hot channel analysis” code

For a realistic analysis of thermal-hydraulics (T-H) transients in light water reactors, KAERI has developed the best-estimate T-H system code, MARS. The code has been improved from the consolidated version of the RELAP5/MOD3 and COBRA-TF codes. Then, the MARS code was coupled with a three-dimensional (3-D) reactor kinetics code, MASTER. This coupled calculation feature, in conjunction with the existing hot channel analysis capabilities of the MARS and MASTER codes, allows for more realistic simulations of nuclear system transients.     

Development and testing of analytical models for the pebble bed type HTRs

The pebble bed type gas cooled high temperature reactor (HTR) appears to be a good candidate for the next generation nuclear reactor technology. These reactors have unique characteristics in terms of the randomness in geometry, and require special techniques to analyze their systems. This study includes activities concerning the testing of computational tools and the qualification of models. Indeed, it is essential that the validated analytical tools be available to the research community. From this viewpoint codes like MCNP, ORIGEN and RELAP5, which have been used in nuclear industry for many years, are selected to identify and develop new capabilities needed to support HTR analysis. The geometrical model of the full reactor is obtained by using lattice and universe facilities provided by MCNP. The coupled MCNP-ORIGEN code is used to estimate the burnup and the refuelling scheme. Results obtained from Monte Carlo analysis are interfaced with RELAP5 to analyze the thermal hydraulics and safety characteristics of the reactor. New models and methodologies are developed for several past and present experimental and prototypical facilities that were based on HTR pebble bed concepts. The calculated results are compared with available experimental data and theoretical evaluations showing very good agreement. The ultimate goal of the validation of the computer codes for pebble bed HTR applications is to acquire and reinforce the capability of these general purpose computer codes for performing HTR core design and optimization studies.     

Advanced treatment of zircaloy cladding high-temperature oxidation in severe accident code calculations: PART II. Best-fitted parabolic correlations

Pressurized water vessel-type reactor (VVER) safety has become a very important issue, in particular for countries in Central and Eastern Europe. For thermal-hydraulic analyses the western codes like RELAP5, CATHARE and ATHLET were used.The purpose of the study was to quantitatively assess the RELAP5 capability to predict the main circulation pump (MCP) trip at nearly full power transient in Mochovce VVER 440/213 nuclear power plant (NPP). The transient parameters were recorded during the start up test program implementation. For accuracy quantification the improved fast Fourier transform based method (FFTBM) was used. The RELAP5/MOD3.2.2 computer code was used for calculation. The results showed very good agreement between calculated and plant measured data. The results also confirmed some previous studies that the simpler is the transient the higher code accuracy is generally achieved.     

Benchmarking analysis of water hammer effects using RELAP5 code and development of RBMK-1500 reactor main circulation circuit model

Correct prediction of water hammer transients is of paramount importance for the safe operation of the plant. Therefore, verification of computer codes capability to simulate water hammer type transients is a very important issue at performing safety analyses for nuclear power plants. Verification of RELAP5/MOD3.3 code capability to simulate water hammer type transients employing the experimental investigations is presented. Experience gained from benchmarking analyses has been used at development of the detail RELAP5 code RBMK-1500 model for simulation of water hammer effects in reactor main circulation circuit. In RBMK-type reactors the water hammers can occur in cases of rapid check valve operation. The performed analysis using RELAP5 code RBMK-1500 model has shown that in general the maximum values of the pressure pulses due to water hammer do not exceed the permissible loads on the pipelines.     

An assessment of a VVER-1000 core during Turbo-Generator load reduction test using RELAP5/MOD3.2 and WIMSD-5B/PARCSv2.7

Reactor dynamic tests, which are categorized as one of the power start-up test groups, are the most complex tests during commissioning of the new nuclear power plants. This paper presents the results of Turbo-Generator load reduction test as one of the reactor dynamic tests for VVER-1000/V446 unit at Bushehr Nuclear Power Plant (BNPP). In this test modeling because of the need for control rod bank worth and core reactivity coefficients, the core geometry has been modeled first by using WIMSD-5B/PARCSv2.7 codes for neutronic calculations. For performing the thermal-hydraulic analysis, the RELAP5/MOD3.2 computer code has been used. The control rod bank worth and core reactivity coefficients obtained from WIMSD-5B/PARCSv2.7 are compared with BNPP FSAR that confirm the ability and reliability of the method. Also comparison of the thermal-hydraulic core parameters obtained from RELAP5/MOD3.2 against actual plant data, indicate that this code can properly predict behavior of VVER-1000 reactor for this dynamic start-up test.     

Review of thermal-hydraulic calculations for Calvert Cliffs and H.B. Robinson PTS study

The thermal-hydraulic calculations for the USNRC pressurized thermal shock study, which were performed by the Los Alamos National Laboratory for the Calvert Cliffs nuclear power plant using the TRAC-PF1/MODI code and by the Idaho National Engineering Laboratory for the H.B. Robinson Unit 2 nuclear power plant using the RELAP5/MOD1.6 code, were reviewed at Brookhaven National Laboratory.To quantitatively review these calculations, a simple method based on mass and energy balances was developed at BNL to predict the primary system temperature. In this approach the entire reactor system was lumped into a single volume and the energy balance was applied to that volume. Because significant nonequilibrium effects made it difficult to estimate the pressures, the upper and lower bounds of the pressure were calculated using adiabatic and equilibrium assumptions.In general, the temperatures and pressures of the primary system calculated by both codes were reasonable. The secondary pressures calculated by TRAC indicated it had some difficulty with the condensation model. However, it is not expected that this uncertainty would affect the transient calculations significantly.Review of one typical transient calculation for each plant is discussed in this paper.