AlGaN/GaN MOS-HEMT With $hbox{HfO}_{2}$ Dielectric and $hbox{Al}_{2}hbox{O}_{3}$ Interfacial Passivation Layer Grown by Atomic Layer Deposition

We have developed a novel AlGaN/GaN metal-oxide-semiconductor high-electron mobility transistor using a stack gate HfO₂/Al₂O₃ structure grown by atomic layer deposition. The stack gate consists of a thin HfO₂ (30-A) gate dielectric and a thin Al₂O₃ (20- A) interfacial passivation layer (IPL). For the 50-A stack gate, no measurable C-V hysteresis and a smaller threshold voltage shift were observed, indicating that a high-quality interface can be achieved using a Al₂O₃ IPL on an AlGaN substrate. Good surface passivation effects of the Al₂O₃ IPL have also been confirmed by pulsed gate measurements. Devices with 1- mum gate lengths exhibit a cutoff frequency (fT) of 12 GHz and a maximum frequency of oscillation (f _MAX) of 34 GHz, as well as a maximum drain current of 800 mA/mm and a peak transconductance of 150 mS/mm, whereas the gate leakage current is at least six orders of magnitude lower than that of the reference high-electron mobility transistors at a positive gate bias.     

AlGaN/GaN Metal–Oxide–Semiconductor High-Electron Mobility Transistors Using Oxide Insulator Grown by Photoelectrochemical Oxidation Method

A photoelectrochemical oxidation method was used to directly grow oxide layer on AlGaN surface. The annealed oxide layer exhibited beta-Ga₂O₃ and alpha-Al₂O₃ crystalline phases. Using a photoassisted capacitance-voltage method, a low average interface-state density of 5.1 times 10¹¹ cm^-2. eV^-1 was estimated. The directly grown oxide layer was used as gate insulator for AlGaN/GaN MOS high-electron mobility transistors (MOS-HEMTs). The threshold voltage of MOS-HEMT devices is -5 V. The gate leakage currents are 50 and 2 pA at forward gate bias of VGS = 10 V and reverse gate bias of V_GS = -10 V, respectively. The maximum value of g_m is 50 mS/mm of VGs biased at -2.09 V.     

The role of cleaning conditions and epitaxial layer structure on reliability of Sc2O3 and MgO passivation on AlGaN/GaN HEMTS

The effect of layer structure (GaN versus AlGaN cap) and cleaning procedure prior to Sc₂O₃ or MgO deposition at 100 °C were examined for their effects on the long-term bias-stress stability of AlGaN/GaN high electron mobility transistors (HEMTs). Surface cleaning by itself was not sufficient to prevent current collapse in the devices. The forward and reverse gate leakage currents were decreased under most conditions upon deposition of the oxide passivation layers. After ≈13 h of bias-stressing, the MgO-passivated HEMTs retain 90% their initial drain–source current. The Sc₂O₃-passivated devices retained 80% recovery of the current under the same conditions.     

Comparative study of AlGaN/GaN metal-oxide-semiconductor heterostructure field-effect transistors with Al2O3 and HfO2 gate oxide

AlGaN/GaN metal-oxide-semiconductor heterostructure field-effect transistors (MOSHFETs) with Al₂O₃ gate oxide which was deposited by atomic layer deposition (ALD) were fabricated and their performance was then compared with that of AlGaN/GaN MOSHFETs with HfO₂ gate oxide. The capacitance (C)-voltage (V) curve of the Al₂O₃/GaN MOS diodes showed a lower hysteresis and lower interface state density than the C-V curve of the HfO₂/GaN diodes, indicating better quality of the Al₂O₃/GaN interface. The saturation of drain current in the I_D-V_GS relation of the Al₂O₃ AlGaN/GaN MOSHFETs was not as pronounced as that of the HfO₂ AlGaN/GaN MOSHFETs. The gate leakage current of the Al₂O₃ MOSHFET was five to eight orders of magnitude smaller than that of the HfO₂ MOSHFETs.     

Frequency-dependent capacitance reduction in high-k AlTiOx and Al2O3 gate dielectrics from IF to RFfrequency range

We have characterized the capacitance and loss tangent for high-k Al₂O₃ and AlTiO_x gate dielectrics from IF (100 KHz) to RF (20 GHz) frequency range. Nearly the same rate of capacitance reduction as SiO₂ was demonstrated individually by the proposed Al₂O₃ and AlTiO_x gate dielectrics as frequency was increased. Moreover, both dielectrics preserve the higher k better than SiO₂ from 100 KHz to 20 GHz. These results suggest that both Al₂O₃ and AlTiO_x are suitable for next generation MOSFET application into RF frequency regime     

High-performance polycrystalline SiGe thin-film transistors usingAl2O3 gate insulators

The use of aluminum oxide as the gate insulator for low temperature (600°C) polycrystalline SiGe thin-film transistors (TFTs) has been studied. The aluminum oxide was sputtered from a pure aluminum target using a reactive N₂O plasma. The composition of the deposited aluminum oxide was found to be almost stoichiometric (i.e., Al₂O₃), with a very small fraction of nitrogen incorporation. Even without any hydrogen passivation, good TFT performance was measured an devices with 50-nm-thick Al₂O₃ gate dielectric layers. Typically, a field effect mobility of 47 cm²/Vs, a threshold voltage of 3 V, a subthreshold slope of 0.44 V/decade, and an on/off ratio above 3×10⁵ at a drain voltage of 0.1 V can be obtained. These results indicate that the direct interface between the Al₂ O₃ and the SiGe channel layer is sufficiently passivated to make Al₂O₃ a better alternative to grown or deposited SiO₂ for SiGe field effect devices     

Substitution of Paraelectric for Conventional Dielectric in AlGaN/GaN MISFETs

A ferroelectric material of paraelectric state is proposed as a substitute for the conventional dielectric in AlGaN/GaN metal–insulator–semiconductor field-effect transistors (MISFETs). Owing to its switchable polarization, the maximum transconductance of a barium strontium titanate (BST)/AlGaN/GaN metal–paraelectric–semiconductor FET (MPSFET) is significantly improved by 44% as compared to a conventional SiN/AlGaN/GaN MISFET. The pinchoff voltage is greatly reduced from $-!$10.7 V for the MISFET to $-$4.7 V for the MPSFET, accompanied with a distinct improvement in the pinchoff characteristics and suppression of soft pinchoff. Small-signal measurements result a comparable frequency performance of the FETs with BST and SiN gate dielectrics. Based on a self-consistent calculation, the switchable polar nature of the paraelectric is revealed to be essential for improving the device transconductance.      

Improved Stability of High-Performance ZnO/ZnMgO Hetero-MISFETs

Improved performance and stability was demonstrated for ZnO/ZnMgO hetero-MISFETs. The MIS gate structures that were formed using either a 50-nm-thick Al₂O₃ or HfO₂ gate dielectric layer were examined by observation of the transfer characteristic hysteresis. A significantly reduced hysteresis of less than 0.1 V was obtained for HfO₂ as compared to that for the Al₂O₃ gate dielectric. By reducing the access resistance, the 1-mum gate devices showed improved transconductance values, as high as 54 mS/mm for Al₂O₃ and 71 mS/mm for HfO₂, which are the highest values ever reported for ZnO-based FETs.     

Effects of Sc2O3 and MgO passivation layerson the output power of AlGaN/GaN HEMTs

The low temperature (100°C) deposition of Sc₂O₃ or MgO layers is found to significantly increase the output power of AlGaN/GaN HEMTs. At 4 GHz, there was a better than 3 dB increase in output power of 0.5×100 μm² HEMTs for both types of oxide passivation layers. Both Sc₂ O₃ and MgO produced larger output power increases at 4 GHz than conventional plasma-enhanced chemical vapor deposited (PECVD) SiN_x passivation which typically showed ⩽2 dB increase on the same types of devices. The HEMT gain also in general remained linear over a wider input power range with the Sc₂O₃ or MgO passivation. These films appear promising for reducing the effects of surface states on the DC and RF performance of AlGaN/GaN HEMTs     

Gate length scaling for Al0.2Ga0.8N/GaNHJFETs: two-dimensional full band Monte Carlo simulation includingpolarization effect

Two-dimensional self-consistent full band Monte Carlo (FBMC) simulator was developed for electron transport in wurtzite phase AlGaN/GaN heterojunction (HJ) FET. Recessed gate Al_0.2Ga_0.8N/GaN HJFET structures with an undoped cap layer were simulated, where the spontaneous and piezoelectric polarization effects were taken into account. The polarization effect was shown to not only increase the current density, but also improve the carrier confinement, and hence improve the transconductance. An off-state drain breakdown voltage (BV_ds) of 300 V and a maximum linear output power (P_max) of 46 W/mm were predicted for a 0.9-μm gate device. For a 0.1-μm gate device, 60 V BV_ds , 20 W/mm P_max, and 160 GHz current-gain cutoff frequency were predicted. Although there is considerable uncertainty due to lack of information on the band structure, scattering rates, and surface conditions, the present results indicate a wide margin for improvements over current performance of AlGaN/GaN HJFETs in the future. To our knowledge, this is the first report on the FBMC simulation for AlGaN/GaN HJFETs     

An Al0.3Ga0.7N/GaN undoped channelheterostructure field effect transistor with Fmax of 107 GHz

An Al_0.3Ga_0.7N/GaN heterostructure field effect transistor (HFET) grown on semi-insulating SiC with an 0.2-μm gate length is reported. A source-drain ohmic contact resistance of 0.15-Ω-mm was achieved through the use of high Al content and high n-type doping (1E19 cm^-3) in the AlGaN donor layer and optimized metallization procedures. We obtained a maximum transconductance of 260 mS/mm, a saturated current density of 1.2 A/mm, and a maximum oscillation frequency in excess of 107 GHz in the devices. The results are one of the best achieved up to now, and they will open up the potential for the applications of AlGaN/GaN HFET's in high-power microwave radar, remote sensing, and communications     

Characteristics of Al/sub 2/O/sub 3//AllnN /GaN MOSHEMT

InAlN/GaN is a new heterostructure system for HEMTs with thin barrier layers and high channel current densities well above 1 A/mm. To improve the leakage characteristics of such thin-barrier devices, AlInN/GaN MOSHEMT devices with a 11 nm InAlN barrier and an additional 5 nm Al₂O₃ barrier (deposited by ALD) were fabricated and evaluated. Gate leakage in reverse direction could be reduced by one order of magnitude and the forward gate voltage swing increased to 4 V without gate breakdown. Compared to HEMT devices of similar geometry, no degradation of the current gain cutoff frequency was observed. The results showed that InAlN/GaN FETs with high channel current densities can be realised with low gate leakage characteristics and high structural aspect ratio by insertion of a thin Al₂O ₃ gate dielectric layer     

Submicrometer Inversion-Type Enhancement-Mode InGaAs MOSFET With Atomic-Layer-Deposited Al2O3 as Gate Dielectric

High-performance inversion-type enhancement-mode n-channel In_0.53Ga_0.47As MOSFETs with atomic-layer-deposited (ALD) Al₂O₃ as gate dielectric are demonstrated. The ALD process on III-V compound semiconductors enables the formation of high-quality gate oxides and unpinning of Fermi level on compound semiconductors in general. A 0.5-mum gate-length MOSFET with an Al₂O₃ gate oxide thickness of 8 nm shows a gate leakage current less than 10^-4 A/cm² at 3-V gate bias, a threshold voltage of 0.25 V, a maximum drain current of 367 mA/mm, and a transconductance of 130 mS/mm at drain voltage of 2 V. The midgap interface trap density of regrown Al₂O₃ on In_0.53Ga_0.47As is ~1.4 x 10¹²/cm² ldr eV which is determined by low-and high-frequency capacitance-voltage method. The peak effective mobility is ~1100 cm² / V ldr s from dc measurement, ~2200 cm²/ V ldr s after interface trap correction, and with about a factor of two to three higher than Si universal mobility in the range of 0.5-1.0-MV/cm effective electric field.     

Self-aligned GaAs p-channel enhancement mode MOS heterostructurefield-effect transistor

Self-aligned GaAs enhancement mode MOS heterostructure field-effect transistors (MOS-HFET) have been successfully fabricated for the first time. The MOS devices employ a Ga₂O₃ gate oxide, an undoped Al_0.75Ga_0.25As spacer layer, and undoped In_0.2Ga_0.8As as channel layer. The p-channel devices with a gate length of 0.6 μm exhibit a maximum DC transconductance g_m of 51 mS/mm which is an improvement of more than two orders of magnitude over previously reported results. With the demonstration of a complete process flow and 66% of theoretical performance, GaAs MOS technology has moved into the realm of reality     

Demonstration of GaN MIS diodes by using AlN and Ga2O3(Gd2O3) as dielectrics

GaN MIS diodes were demonstrated utilizing AlN and Ga₂O₃(Gd₂O₃) as insulators. A 345 Å of AlN was grown on the MOCVD grown n-GaN in a MOMBE system using trimethylamine alane as Al precursor and nitrogen generated from a SVT RF N₂ plasma. For the Ga₂O₃(Gd₂O₃) growth, a multi-MBE chamber was used and a 195 Å oxide was E-beam evaporated from a single crystal source of Ga₅Gd₃O₁₂. The forward breakdown voltage of AlN and Ga₂O₃(Gd₂O₃) diodes are 5 and 6 V, respectively, which are significantly improved over 1.2 V from that of a Schottky contact. From the C–V measurements, both kinds of diodes showed good charge modulation from accumulation to depletion at different frequencies. The insulator/GaN interface roughness and the thickness of the insulator were measured with X-ray reflectivity.     

Short channel AlGaN/GaN MODFET's with 50-GHz fT and1.7-W/mm output-power at 10 GHz

A thin barrier-donor layer of 200 Å was used to increase the active input capacitance and improve the extrinsic current-gain cutoff frequency (f_t) of short-gate-length AlGaN/GaN MODFETs. 0.2-μm gate-length devices fabricated on such an epi-structure with sheet carrier density of ~8×10¹² cm^-2 and mobility of 1200 cm²/Vs showed a record f_t of 50 GHz for GaN based FETs. High channel saturation current and transconductance of 800 mA/mm and 240 mS/mm respectively were also achieved along with breakdown voltages of 80 V per μm gate-drain spacing. These excellent characteristics translated into a CW output power density of 1.7 W/mm at 10 GHz, exceeding previous record for a solid-state HEMT     

High-Performance Inversion-Type Enhancement-Mode InGaAs MOSFET With Maximum Drain Current Exceeding 1 A/mm

High-performance inversion-type enhancement- mode (E-mode) n-channel In_0.65Ga_0.35As MOSFETs with atomic-layer-deposited Al₂O₃ as gate dielectric are demonstrated. A 0.4-mum gate-length MOSFET with an Al₂O₃ gate oxide thickness of 10 nm shows a gate leakage current that is less than 5 times 10^-6 A/cm² at 4.0-V gate bias, a threshold voltage of 0.4 V, a maximum drain current of 1.05 A/mm, and a transconductance of 350 mS/mm at drain voltage of 2.0 V. The maximum drain current and transconductance scale linearly from 40 mum to 0.7 mum. The peak effective mobility is ~1550 cm²/V ldr s at 0.3 MV/cm and decreases to ~650 cm²/V ldr s at 0.9 MV/cm. The obtained maximum drain current and transconductance are all record-high values in 40 years of E-mode III-V MOSFET research.     

Low-frequency noise in Si0.7Ge0.3 surface channel pMOSFETs with ALD HfO2/Al2O3 gate dielectrics

Low-frequency noise was characterized in Si_0.7Ge_0.3 surface channel pMOSFETs with ALD Al₂O₃/HfO₂/Al₂O₃ stacks as gate dielectrics. The influences of surface treatment prior to ALD processing and thickness of the Al₂O₃ layer at the channel interface were investigated. The noise was of the 1/f type and could be modeled as a sum of a Hooge mobility fluctuation noise component and a number fluctuation noise component. Mobility fluctuation noise dominated the 1/f noise in strong inversion, but the number fluctuation noise component, mainly originating from traps in HfO₂, also contributed closer to threshold and in weak inversion. The number fluctuation noise component was negligibly small in a device with a 2 nm thick Al₂O₃ layer at the SiGe channel interface, which reduced the average 1/f noise by a factor of two and decreased the device-to-device variations.     

High-density MIM capacitors using Al2O3 andAlTiOx dielectrics

We have investigated the electrical characteristics of Al₂ O₃ and AlTiO_x MIM capacitors from the IF (100 KHz) to RF (20 GHz) frequency range. Record high capacitance density of 0.5 and 1.0 μF/cm² are obtained for Al₂ O₃ and AlTiO_x MIM capacitors, respectively, and the fabrication process is compatible to existing VLSI backend integration. However, the AlTiO_x MIM capacitor has very large capacitance reduction at increasing frequencies. In contrast, good device integrity has been obtained for the Al₂O₃ MIM capacitor as evidenced from the small frequency dependence, low leakage current, good reliability, small temperature coefficient, and low loss tangent     

High-temperature performance of AlGaN/GaN HFETs and MOSHFETs

Performance of AlGaN/GaN HFETs and Al₂O₃/AlGaN/GaN MOSHFETs at the elevated temperatures up to 425 °C was investigated. Static output and transfer characteristics were measured and the saturation drain current, the peak transconductance and the series conductance as a function of temperature were evaluated. All these characteristic features of HFETs and MOSHFETs decreased with increased temperature. At 425 °C the devices exhibited ∼30% of their saturation drain current, peak transconductance and series conductance evaluated at room temperature. The device performance at elevated temperatures follows exactly the T^x dependence with a power x = −1.5. This indicates that the temperature dependence of the mobility of channel electrons due to phonon scattering is the predominant effect describing high-temperature performance of AlGaN/GaN HFETs and MOSHFETs.