不同衬底上低温生长的ZnO晶体薄膜的结构及光学性质比较

采用电子束反应蒸发方法,在单晶Si（001）及玻璃衬底上低温外延生长了沿C轴高度取向的单晶ZnO薄膜,并对沉积的ZnO晶体薄膜的结构和光学性质进行了分析比较。通过对ZnO蒲膜的X射线衍射（XRD）分析及光致荧光激发谱（PLE）测量,研究了衬底材料结构特性、生长温度及反应气氛中充O2对ZnO薄膜的晶体结构和晶体光学吸收特性的影响。结果表明：①衬底温度对沉积的ZnO薄膜的晶体结构影响显,玻璃衬底上生长ZnO薄膜的最佳温度比Si(001)衬底上生长的最佳温度要高70℃;②虽在最佳生长条件下获得的ZnO薄膜的的XRD结果（半高宽和衍射强度）相近,但光学吸收特性有较大差异,Si(001)衬底上生长的ZnO薄膜优于玻璃衬底上生长的ZnO薄膜;③反应气氛中的O2分压对XRD结构影响不大,但对PLE谱影响显,充O2后能明显改善吸收边特性。     

衬底温度对磁控溅射制备外延ZnO薄膜结构特性的影响

在不同的衬底温度下,采用磁控溅射方法在蓝宝石(0001)衬底上制备了外延生长的ZnO薄膜.采用原子力显微镜(AFM)、X射线衍射仪(XRD)、可见-紫外分光光度计系统研究了衬底温度对ZnO薄膜微观结构和光学特性的影响.AFM结果表明在不同村底温度制备的ZnO薄膜具有较为均匀的ZnO晶粒,且晶粒的尺寸随衬底温度的增加逐渐增大.XRD结果显示不同温度生长的ZnO薄膜均为外延生长,400℃生长的薄膜具有最好的结晶质量;光学透射谱显示在370nm附近均出现一个较陡的吸收边,表明制备的ZnO薄膜具有较高的质量,其光学能带隙随着衬底温度的增加而减小.     

PLD法生长高质量 ZnO薄膜及其光电导特性研究

采用脉冲激光沉积（PLD）法在单晶Si（100）衬底上生长ZnO薄膜，以X射线衍射（XRD）和场发射扫描电镜（SEM）等手段分析了所得ZnO薄膜的晶体结构和微观形貌．结果表明，随着衬底温度和薄膜生长时氧分压的增加，ZnO薄膜的晶体结构和化学计量比得到显著改善．优化工艺（700℃，20Pa）下生长的ZnO薄膜呈c轴高度择优取向，柱状晶垂直衬底表面生长，结构致密均匀．以不同暗电阻的ZnO薄膜为材料，利用剥离（1ift-off）技术制备了MSM结构ZnO光电导型紫外探测器．紫外光照射前后的I-V特性测试表明ZnO薄膜产生非常明显的光电导现象，分析了其光电响应机理．     

PLD生长的ZnO薄膜的微结构及其发光特性研究

在不同的衬底温度下，通过脉冲激光淀积（PLD）方法在Si衬底上生长出c轴高度取向的ZnO薄膜。ZnO薄膜的结构分别通过X射线衍射（XRD）和广延X射线吸收精细结构（EXAFS）来表征，而表面成份和化学态则通过X射线光电子能谱来研究。利用光致发光（PL）来研究样品的发光特性。XRD结果和EXAFS结果都表明了500℃时生长的ZnO薄膜的结晶性比300℃时生长的要好。EXAFS结果和XPS结果显示，300℃时生长的ZnO薄膜处于富氧状态，而500℃时生长的则处于缺氧状态。结合XRD谱、EXAFS谱、XPS谱和PL谱的结果可以看到：随着ZnO薄膜的结晶性变好，它的紫外发光增强；另一方面，随着ZnO薄膜中O的含量减少，绿光发射变强。我们的结果表明绿光发射与ZnO中氧空位（V0）有关。     

直流磁控溅射有机衬底和玻璃衬底ZnO：Al薄膜结构及特性的研究

利用直流磁控溅射法在有机薄膜衬底和普通玻璃衬底上制备出了具有良好附着性的ZnO：Al透明导电膜，对制备薄膜的结构和光学特性进行了比较研究。研究发现：铝掺杂的氧化锌薄膜是多晶膜，具有六角纤锌矿结构；在衬底温度为100℃，溅射压强1．0Pa，氧氩比为1：2．58时，ZnO：Al薄膜具有（002）择优取向，晶化也比较好，在可见光区的平均透过率分别达到了77．6％和82％。     

RF磁控溅射法制备ZnO薄膜的XRD分析

采用RF磁控溅射法，在玻璃村底上制备多晶ZnO薄膜，并对所制备的ZnO薄膜在空气气氛中进行了不同温度（350～600℃）的退火处理和600℃时N2气氛中的退火处理。利用X射线衍射分析了溅射参数如溅射功率、溅射氧分压、衬底温度以及退火处理对ZnO薄膜结晶性能的影响。结果表明，合适的衬底温度和退火处理能够提高ZnO薄膜的结晶质量。     

衬底温度对Sn掺杂ZnO薄膜结构、电学和光学性能的影响

采用射频磁控溅射技术在石英衬底上制备了掺杂浓度为0.5％(原子分数)的ZnO∶Sn(TZO)薄膜,研究了不同衬底温度下薄膜的结构、形貌、电学和光学的性能.研究发现,TZO薄膜沿着C轴择优生长,在400℃时结晶度最好,最低电阻率为2.619×10-2Ω·cm,在可见光范围内具有较好的透光率.     

衬底温度对ZnO薄膜生长过程及微观结构的影响研究

以醋酸锌水溶液为前驱体,采用改进的超声喷雾热解法在Si(100)衬底上沉积ZnO薄膜,以X射线衍射(XRD)、扫描电镜(SEM)等手段分析所得ZnO薄膜的晶体结构和微观形貌,着重考察了衬底温度对ZnO薄膜生长过程及微观结构的影响.结果表明,在衬底温度为500℃下所得ZnO薄膜表面均匀光滑,属六方纤锌矿结构,且沿c轴择优生长,晶粒尺寸的为40～50nm;衬底温度对ZnO薄膜生长过程影响显著,随衬底温度的升高,薄膜生长速率存在一极限值,且ZnO薄膜的c轴取向趋势增强,晶粒尺寸得到细化.     

SiO2/Si衬底制备ZnO薄膜及表征

本文报道了利用脉冲激光沉积技术在热氧化p型硅衬底上生长ZnO外延薄膜.引入高阻非晶SiO2缓冲层,有效地降低了检测过程中单晶衬底对ZnO薄膜的电学性能影响.利用XRD,SEM,Hall和PL对其进行研究.结果表明,在衬底温度为500℃时,生长的ZnO薄膜具有优良的晶体质量,电学性能和发光性能.     

直流反应磁控溅射生长p型ZnO薄膜及其特性的研究

本文报道了利用直流反应磁控技术生长p型ZnO薄膜。ZnO薄膜在不同的衬底温度沉积于α Al2 O3 (0 0 0 1)衬底上 ,生长气氛为NH3 O2 中。利用X射线衍射、Hall试验和透射光谱对其性能进行研究 ,结果表明 ,ZnO薄膜为高度c轴取向 ,在 5 0 0℃的衬底温度下具有很好的结晶性能 ,而且 ,该温度下ZnO还实现了p型转变 ,电阻率为 10 3 Ω·cm ,载流子浓度 10 15cm-3 ,Hall迁移率 3 4cm2 / (V·s)。这是利用溅射技术首次制备出p ZnO薄膜。实验还表明p ZnO薄膜在可见光区域具有 90 %的高透射率 ,室温下光学带宽约为 3 2 1eV。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...