Photocatalytic H2 Production from Ethanol–Water Mixtures Over Pt/TiO2 and Au/TiO2 Photocatalysts: A Comparative Study

Pt/TiO₂ (Pt loadings 0–4 wt%) and Au/TiO₂ (Au loadings 0–4 wt%) photocatalysts were synthesized, characterized and tested for H₂ production from ethanol–water mixtures (80 vol% ethanol, 20 vol% H₂O) under UV excitation. Average metal nanoparticle sizes determined by TEM were 1–3 nm for Pt in the Pt/TiO₂ photocatalysts and 5–7 nm for Au in the Au/TiO₂ photocatalysts. Au/TiO₂ showed an intense localized surface plasmon resonance feature at ~570 nm, typical for metallic Au nanoparticles of diameter ~5 nm supported on TiO₂. X-ray photoelectron spectroscopy and X-ray diffraction analyses established that Pt and Au were present in metallic form on the TiO₂ support. X-ray fluorescence revealed close accord between nominal and actual Pt and Au loadings. The Au/TiO₂ and Pt/TiO₂ photocatalysts both displayed very high activities for H₂ production under UV irradiation, with the Au/TiO₂ samples affording slightly superior rates of H₂ production at most metal loadings. The 2 wt% Au/TiO₂ and 1 wt% Pt/TiO₂ photocatalysts showed the highest H₂ production rates (32–34 mmol g^?1 h^?1). Photoluminescence studies confirmed that Pt and Au nanoparticles positively enhance the photocatalytic properties of P25 TiO₂ for H₂ production by acting as electron acceptors and thereby suppressing electron–hole pair recombination in TiO₂.     

Synthesis and Characterization of Polyaniline:TiO2 Nanocomposites

Thin films of polyaniline (PANi) and PANi:titanium oxide (TiO₂) composites have been synthesized by sol—gel spin coating technique. The TiO₂ powder of particle size 50–60 nm was synthesized by sol–gel technique and the polyaniline was synthesized by chemical oxidative polymerization of aniline. The composite films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) Fourier transform infrared (FTIR) and UV-vis spectroscopy, and the results were compared with polyaniline films. The intensity of the diffraction peaks for PANi:TiO₂ composites is lower than that for TiO₂. The characteristic FTIR peaks of PANi were found to shift to a higher wave number in the PANi:TiO₂ composite. These observed effects have been attributed to the interaction of TiO₂ particles with PANi molecular chains. The room temperature resistivity of polyaniline:nano-TiO₂ composite is 3.43 × 10³ Ω cm and the resistivity of pure nano-TiO₂ particles is 1.60 × 10⁶ Ω cm.     

Ni-doped TiO2 hollow spheres as electrocatalysts in water electrolysis for hydrogen and oxygen production

This work represented the electrocatalytic properties of Ni-doped titania hollow sphere materials in hydrogen and oxygen evolution during water electrolysis from acidic media. Titania hollow sphere particles were synthesized using poly(styrene-methacrylic acid) latex as template material, and various amount of nickel were doped over the sphere using nickel (II) sulfate as the precursor of nickel. The presence of rutile TiO₂ and NiO phases were revealed during XRD analysis, indicating the critical growth of nickel on the surface of the hollow sphere catalysts. BET surface area results also shown the 166.76 m² g^?1 value for 30 wt% Ni/TiO₂ hollow sphere sample. The SEM and TEM images were confirmed the hollow sphere structure of the catalysts with diameter of 0.8–0.9 μm. The cyclic voltammetric studies proved the presence of both hydrogen and oxygen evolution peaks for all the hollow sphere samples. The anodic peak current density value, which usually represents the oxygen evolution phenomenon, was revealed as 13 mA cm^?2 for 25 wt% Ni-loaded sample; whereas, the hydrogen evolution peak was most intense for 30 wt% Ni/TiO₂ material with cathodic peak current density of 32 mA cm^?2. The average value of ?1.42 were determined as the reaction order of the system irrespective of the nickel loading and heating duration in the synthesis of hollow sphere materials. During photocatalytic water splitting, 30 wt% Ni/TiO₂ hollow sphere sample yielded the highest amount of hydrogen in all irradiation time span.     

Influence of Surface Modified MWCNTs on the Mechanical, Electrical and Thermal Properties of Polyimide Nanocomposites

Polyamic acid, the precursor of polyimide, was used for the preparation of polyimide/multiwalled carbon nanotubes (MWCNTs) nanocomposite films by solvent casting technique. In order to enhance the chemical compatibility between polyimide matrix and MWCNTs, the latter was surface modified by incorporating acidic and amide groups by chemical treatment with nitric acid and octadecylamine (C₁₈H₃₉N), respectively. While the amide-MWCNT/polyimide composite shows higher mechanical properties at low loadings (<3 wt%), the acid-MWCNT/polyimide composites perform better at higher loadings (5 wt%). The tensile strength (TS) and the Young’s modulus (YM) values of the acid-MWCNT/polyimide composites at 5 wt% MWCNT loadings was 151 and 3360 MPa, respectively, an improvement of 54% in TS and 35% in YM over the neat polyimide film (TS = 98 MPa; YM = 2492 MPa). These MWCNT-reinforced composites show remarkable improvement in terms of thermal stability as compared to that for pure polyimide film. The electrical conductivity of 5 wt% acid modified MWCNTs/polyimide nanocomposites improved to 0.94 S cm ⁻¹ (6.67 × 10 ⁻¹⁸ S cm⁻¹ for pure polyimide) the maximum achieved so far for MWCNT-polyimide composites.     

A quaternized poly(vinyl alcohol)/chitosan composite alkaline polymer electrolyte: preparation and characterization of the membrane

Quaternized poly(vinyl alcohol)/chitosan (QPVA/CS) composite membranes were prepared by solution casting method with AlCl₃·6H₂O aqueous solution as solvent for CS and glutaraldehyde as a crosslinker. The crystalline, thermal and mechanical properties of the QPVA/CS composite membranes were studied by Fourier transform infrared spectroscopy, X-ray diffractometry, differential scanning calorimetry, thermogravimetry and tensile test measurements, respectively. The composite membranes were immersed in potassium hydroxide aqueous solution to form polymer electrolyte membranes. The alkaline uptake, swelling ratio, ion conductivity and methanol permeability of the electrolyte membranes were studied. The experimental results indicated that aluminum chloride hexahydrate (AlCl₃·6H₂O) had a positive effect on the mechanical properties of the QPVA/CS composite membrane. The elongation-at-break of this membrane reached the maximum of 401.0%. The alkaline uptake and swelling ratio of the composite membranes decreased. With the addition of 30 wt% AlCl₃·6H₂O, the composite membrane showed the ion conductivity and methanol permeability of 1.82 × 10^?2 S cm^?1 and 2.17 × 10^?6 cm² s^?1, respectively. These values were higher than those of the membrane with acetic acid as the solvent for CS. The selectivity of the QPVA/CS membrane could reach 8.39 × 10³ S s cm^?3. This study showed that with AlCl₃·6H₂O as the solution for CS, the high performance QPVA/CS composite alkaline polymer electrolyte membrane could be prepared.     

Insights into the physico-chemical behavior of CoCl<Subscript>2</Subscript>/polyimide hybrid materials

Hybrid fluorinated polyimide materials have been obtained by incorporation of various quantities of cobalt(II) chloride (CoCl₂) into polyimide matrix. Polycondensation reaction of equimolar amounts of 4,4′-diamino-3′3′-dimethyldiphenylmethane and 2,2′-bis(3,4-dicarboxyphenyl) hexafluoropropane dianhydride has been carried out to produce in the first stage a polyamidic acid solution in which CoCl₂?×?6H₂O has been placed. Further thermal treatment of this system led to the corresponding imide structure filled with the halide salt. An exhaustive study was directed to the influence of Co²⁺ ions on the modified polyimide behavior as a function of its surroundings. To survey the functional properties of as-obtained Co²⁺-containing polyimide systems, several techniques such as FTIR, UV-vis and broadband dielectric spectroscopy, differential scanning calorimetry, and thermogravimetric and scanning electron microscopy were employed. A special concern was directed to the study of the optical properties induced by the addition of CoCl₂ into polymer solutions and films. The magnetic response of the polyimide was investigated in correlation with the salt quantity embedded in the PI film. The variation of the real and imaginary parts of the hybrid films’ dielectric permittivity was registered in a broad frequency and temperature range, from 10 to 10⁶ Hz and from ?130 to 230 °C, respectively.     

Effect of TiO2 on sinterability and physical properties of pressureless sintered Ti3AlC2 ceramics

TiO₂ was selected as effective sintering aid for pressureless sintering of Ti₃AlC₂ ceramics in this study. The addition of only 5?wt% TiO₂ largely promotes the densification and nearly dense Ti₃AlC₂ ceramic was obtained by pressureless sintering at 1500?°C. Significant strengthening and toughening effects were observed with the addition of TiO₂. High Vickers hardness, flexural strength and fracture toughness of 3.22?GPa, 298?MPa and 6.2?MPa?m^?1/2, respectively, were achieved in specimen pressureless sintered with 10?wt% TiO₂. Additionally, the addition of 5?wt% TiO₂ had no deleterious effect on the excellent oxidation resistance of Ti₃AlC₂ ceramic under 1200?°C water vapor atmosphere, while addition of 10?wt% TiO₂ accelerates the oxidation rate by two orders of degree.     

Preparation of composite membranes with polyimides and poly (amide-imide)s skin via interfacial condensation for air separation

Composite membranes were prepared by the interfacial condensation of water-soluble diamines with an organic solvent (dichloromethane)-soluble dicarbo-methoxy terephthaloyl chloride or carbomethoxy terephthaloyl chloride on top of a porous aluminum oxide support. The morphology of skin on the composite membranes is different in the two different procedures. The polyimide composite membranes with 40-times coatings provide a high gas permeation rate of oxygen and good permselectivity [α(O₂/N₂)]. The composite membrane with the polyimides skin at 40-times coatings had a gas permeation rate of oxygen range from 83 × 10⁻⁵ to 130 × 10⁻⁵ cm³(STP) s⁻¹ cm⁻² cmHg⁻¹, and a permselectivity [α(O₂/N₂)] range of 3.57 to 5.60. The composite membrane with poly (amide-imide)s skin at 40-times coatings had a gas permeation rate of oxygen range from 102 × 10⁻⁵ to 146 × 10⁻⁵ cm³(STP) s⁻¹ cm⁻² cmHg⁻¹, and the permselectivity (α(O₂/N₂)) range from 3.20 to 4.96.     

Comparative performance analysis of electrospun TiO2 embedded poly(vinylidene fluoride) nanocomposite membrane for supercapacitors

For an efficient energy storage system, effective material is to be used. In the present work, novel poly(vinylidene fluoride)/titanium oxide (PVdF/TiO₂) composite membranes were developed using electrospinning technique, as separator for supercapacitors. Different weight percentages of TiO₂ nanoparticle (0, 5, 10, 15, and 20 wt%) were mixed with 20 wt% of PVdF in a 50:50 wt% of tetrahydrofuran and dimethylacetamide solvent. Various physical and electrochemical properties including fiber diameter, thermal stability, crystallinity, porosity, and electrolytic uptake were studied to identify the best membrane with optimum TiO₂ wt% exhibiting superior characteristics. SEM and TGA studies revealed that the developed PVdF/TiO₂ composite membrane with 10 wt% showed improved properties with a lower average diameter of about 66 ± 8 nm, enhanced thermal stability up to 513.15°C and higher porosity of 89%, respectively compared to other membranes. The crystallinity, ionic conductivity, and specific capacitance of the nonwoven separator membranes were determined using X-ray diffraction technique, electrolytic uptake, and charge–discharge studies, respectively. The present study revealed that the addition of TiO₂ nanoparticles improved the physical and thermochemical properties of the separator membrane substantially and PVdF/TiO₂ composite membrane with 10 wt% displayed superior performance compared to other membranes.     

Facile fabrication approach for a novel multifunctional superamphiphobic coating based on chemically grafted montmorillonite/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-polydimethylsiloxane binary nanocomposite

In this paper, a novel multifunctional superamphiphobic coating for anticorrosion was successfully prepared on aluminum substrate via a simple spraying technique. Al₂O₃ nanoparticles were chemically grafted onto montmorillonite (MMT) nanosheets via coupling effect of NH₂-C₃H₆-Si(OC₂H₅)₃ (KH-550) and then modified by low surface energy material polydimethylsiloxane (PDMS). The ethylene tetrafluoroethylene (ETFE) composite coating with 25 wt% MMT/Al₂O₃-PDMS binary nanocomposite exhibited well-designed nano/μ structures and possessed superamphiphobicity with high contact angles towards water (164°), glycerol (158°) and ethylene glycol (155°). This coating demonstrated outstanding self-cleaning ability and strong adhesive ability (Grade 1 according to the GB/T 9286). The superhydrophobicity could be maintained after 8000 times abrasion or annealing treatment for 2 h under 350 °C. The coating still retained high water-repellence after immersion in 1 mol/L HCl (146°), 1 mol/L NaOH (144°) and 3.5 wt% NaCl (151°) solutions for 30 d. It should be noted that this superamphiphobic coating revealed excellent long-term corrosion protection with extremely low corrosion rate (4.3 × 10^?3 μm/year) and high protection performance (99.999%) after 30 d immersion in 3.5 wt% NaCl solutions based on electrochemical corrosion measurements. It is believed that such integrated functional coating could pave new way for self-cleaning and anticorrosion applications under corrosive/abrasive environment.     

Significant Improvement in Activity and Stability of Pt/TiO2 Catalyst for Water Gas Shift Reaction Via Controlling the Amount of Na Addition

Na promoted Pt/TiO₂ catalysts have been studied under high severity, near equilibrium, conditions for use as a single stage WGS catalyst. Addition of 3 wt% Na to a 1 wt% Pt/TiO₂ catalyst has been found to improve water gas shift activity significantly compared to Pt/TiO₂, Pt/CeO₂, and Pt–Re/TiO₂ catalysts. This catalyst is stable when the reaction temperature is higher than 250 °C. Deactivation occurred when the reaction temperature was lower than 250 °C, however, returning the temperature to higher than 250 °C fully recovered activity. TEM observations revealed that addition of Na inhibited Pt particle sintering. These results suggest that Na promoted Pt/TiO₂ is a promising single stage water gas shift catalyst for small scale hydrogen production.     

P(VDF-HFP)-based micro-porous composite polymer electrolyte prepared by in situ hydrolysis of titanium tetrabutoxide

A micro-porous composite polymer electrolyte (MCPE) was prepared in situ by adding TiO₂ nanoparticles from the hydrolysis of titanium tetrabutoxide to a solution of poly(vinylidenefluoride-co-hexafluoropropylene) [P(VDF-HFP)] copolymer. The prepared microporous polymer films (MCPFs) were characterized by scanning electronic microscopy, X-ray diffraction, thermogravimetric analysis, FT-IR and electrochemical interface resistance. After the addition of TiO₂ nanoparticles the polarity of CF₂ groups in the polymer chains and the crystallinity of the MCPFs decreased. When the composite polymer film contained 8.5 wt% of TiO₂ nanoparticles the MCPE exhibited excellent electrochemical properties such as high ionic conductivity, up to 2.40 × 10⁻³ S cm⁻¹ at room temperature.     

Preparation of PDMS—Silica Nanocomposite Membranes with Silane Coupling for Recovering Ethanol by Pervaporation

In this article, the composite polydimethylsiloxane (PDMS) membranes supported by cellulose-acetate (CA) microfiltration membrane were successfully prepared by adding nano-fumed silica particles modified with a silane coupling reagent, NH₂-C₃H₆-Si(OC₂H₅)₃. The effects of silica content, feed concentration, and feed temperature on the pervaporation performances of the nano-composite PDMS membranes were investigated for recovering ethanol from aqueous solution by pervaporation. It was found that adding the modified silica particles significantly improved the pervaporation performances of the composite membranes. When the silica content in the membrane was 5 wt%, for a 5 wt% ethanol/water mixture at 40°C, the permeation flux of the membrane maintained about 200 g · m^?2 · h^?1 and separation factor reached the maximum value of 19.     

Photocatalytic enamel/TiO2 coatings developed by electrophoretic deposition for methyl orange decomposition

The aim of this study was to obtain photocatalytic coatings, capable to decompose organic pollutants, through Electrophoretic Deposition (EPD) of enamels containing respectively 0%, 5%, 10%, 15% (in wt%) of TiO₂ onto carbon steel substrates. High quality and homogeneous coatings were obtained by applying 12.5?V during 10?s, as the best EPD conditions. The layers were subsequently heat treated at 740?°C for 10?min, in order to obtain dense glazes.Rietveld refinement of XRD patterns and Raman results show that, after the heat treatment at 740?°C, TiO₂ mostly exists as anatase, responsible of the photocatalytic effect. Semi-quantitative chemical analysis indicate segregation of TiO₂ on the coatings surface, reaching saturation in the sample with 10?wt% TiO₂. FEG-SEM observations reveal rod-like and spherical Ti-rich phases along the cross section of the coatings; some Ti was also dissolved into the enamel. 3D topographical mapping shows that, by adding TiO₂, surface roughness increases significantly.Photocatalytic tests were carried out using a 2?×?10^?5 M aqueous solution of Methyl Orange (MO) as an organic pollutant. By comparing the decomposition rate of MO achieved with the pure enamel (0% of TiO₂) and with the sample with 10% of TiO₂, it was shown that the addition of 10% of TiO₂ results in 90% photocatalytic efficiency.Moreover, the permeation of organic compounds and their UV degradation were studied by measuring the water contact angle onto the enamel surface directly after dipping into oleic acid and after various UV irradiation times. The longer the UV irradiation time, the lower the contact angle, down to a minimum of 14.54° after 8?h of UV irradiation. This means, the compound was initially adsorbed on the enamel/TiO₂ coating surface (10?wt% TiO₂) but was efficiently decomposed upon UV irradiation.     

Hydrophilic TiO2 decorated carbon nanotubes/sulfonated poly(ether ether ketone) composite proton exchange membranes for fuel cells

Sulfonated poly(ether ether ketone) (SPEEK) is currently considered to be one of the most potential candidates of commercial perfluorinated sulfonic acid proton exchange membranes. To balance the proton conductivity and mechanical properties of SPEEK, nano TiO₂ coated carbon nanotubes (TiO₂@CNTs) were prepared using a benzyl alcohol-assisted sol-gel method and then used as a new nanofiller to modify SPEEK to prepare SPEEK/TiO₂@CNTs composite membranes. The thick insulated TiO₂ coating layer can effectively avoid the risk of electronic short-circuiting formed by CNTs, while the hydrophilicity of TiO₂ can also reduce the polar difference between CNTs and SPEEK matrix, thus promoting the homogeneous dispersion of CNTs in the composites. As a result, the composite membranes demonstrated simultaneously improved strength and proton conductivity. Incorporating 5 wt% of TiO₂@CNTs exhibited 31% growth in mechanical strength when compared with pure SPEEK. Moreover, the maximum conductivity was 0.104 S cm⁻¹ (80°C) for the composite membrane with 5 wt% of TiO₂@CNTs, which was nearly twice as high as that of SPEEK membrane (0.052 S cm⁻¹).     

Preparation of aerochitin‐TiO2 composite for efficient photocatalytic degradation of methylene blue

An aerochitin–titania (TiO₂) composite was successfully synthesized and characterized by Fourier transform infrared spectroscopy, X‐ray diffraction, thermogravimetric analysis, field emission scanning electron microscopy, and N₂ adsorption isotherms. The photocatalytic activity of the composite was investigated on the degradation of the model organic pollutant, methylene blue (MB) dye, under UV irradiation. The aerochitin–TiO₂ composite showed excellent adsorptive and photocatalytic activity with a degradation degree of 98% for MB. The first‐order rate constants for the photodegradation MB by TiO₂ nanoparticles and aerochitin–TiO₂ composite were found to be (3.49 ± 0.04) × 10^?3 and (1.82 ± 0.02) × 10^?2 min^?1. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45908.     

Physico-Chemical Effects on the Scale-Up of Ag Photodeposition on TiO2 Nanoparticles

We have previously demonstrated that TiO₂ nanoparticles can be functionalized by photodeposition with silver or gold particles in the 1?C2 nm range presumed to be desirable for catalysis applications. However, the preparation of these samples directly on microscope grids, while conducive to particle size determinations, did not produce sufficient materials for reaction studies. We report here scale-up techniques designed to produce greater quantities of material for testing, while maintaining characteristics that contribute to uniformity in the deposition process. For the scale-up process, an irradiation source with highly uniform intensity is necessary to generate Ag/TiO₂ samples with consistent Ag loading. In addition, control of the precursor concentration is also required to produce Ag/TiO₂ samples with high Ag loading and narrow Ag size distribution. The optimum conditions for the scale-up process found in this study involved Ag photodeposition from a 5 × 10^?3 M AgNO₃ solution using a high pressure Hg lamp at 366 nm for 60 s. Under these reaction conditions, the size of Ag particles determined by TEM and HAADF-STEM imaging was within 1?C2 nm and the Ag loading was ~3.2 wt%. Achievement of this level of uniformity required control of the uniformity of illumination, as well as of the solution concentration and irradiation conditions. Higher solution concentrations and higher power led to the growth of larger (ca. 10 nm) silver particles. In contrast, the loading and size distribution of the Ag particles photodeposited were remarkably insensitive to the source and morphology of the TiO₂ nanoparticles utilized. No Ag peak was resolved in the XRD patterns for Ag/TiO₂ samples obtained from the optimized scale-up process, corroborating the size range determination of the Ag nanoparticles. XPS showed that the Ag particles in all cases were metallic Ag.     

Atomic oxygen resistant coating from poly(tetramethyldisilylene‐co‐styrene)

A polydisilahydrocarbon, namely, poly(tetramethyldisilylene‐co‐styrene), synthesized from dimethyldichlorosilane and styrene in 1 : 0.5 mol ratio under dechlorination conditions was evaluated as an atomic oxygen (AO) resistant coating for polyimide film and C‐polyimide composite. Exposure of the polymer coating on a quartz plate to an AO fluence of 2.1 × 10²¹ atoms/cm² resulted in practically no mass loss, indicating the AO resistance of the polymer. Ten percent solution of the polymer in toluene was applied on aluminized Kapton® polyimide film (125 μm thick) to obtain a coating thickness of ～ 5 μm on the unaluminized surface. In a similar way, the coating was applied on a C‐polyimide composite. The coated and uncoated samples of Kapton® film and C‐polyimide composite were exposed to AO in a plasma barrel system. The uncoated aluminized Kapton® film (125 μm) lost 6.35 mg/cm² when exposed to AO fluence of 1.6 × 10²¹ atoms/cm² whereas the corresponding coated film lost only 0.14 mg/cm² even after exposure to AO fluence of 2.1 × 10²¹ atoms/cm². In the case of the C‐polyimide composite, the uncoated sample lost 63.64 mg/cm² on exposure to AO fluence of 1.8 × 10²¹ atoms/cm² whereas the coated one lost only 0.21 mg/cm² even after exposure to AO fluence of 2.1 × 10²¹ atoms/cm². SEM studies suggest that the coating offers good protection to the substrates. Formation of cracks on some portions of the coating was noticed. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2368–2375, 2004     

Improvement in corrosion resistance of micro-arc oxidation coating on PVD Ti-coated aluminum alloy 7075

Surface treatments are always needed to enhance corrosion-resistant performance of aluminum (Al) alloys when they are used in seawater environments. The paper aimed to prepare the composite oxide ceramic coating on Al alloy 7075 by combining micro-arc oxidation (MAO) and magnetron sputtering technology. The Al substrate was precoated with titanium (Ti) layer by using the magnetron sputtering technology and then treated by MAO in the alkaline aluminate electrolyte, resulting in a composite MAO coating, which is composed of Al₂O₃ and TiO₂ along with the complex oxide (Al₂TiO₅). The potentiodynamic polarization and electrochemical impedance spectroscopy were carried out to evaluate the corrosion performance of the MAO coatings in 3.5 wt% NaCl solution. Better corrosion resistance was observed for composite oxide coating than the reference MAO coating on the bare Al, as evidenced by the higher corrosion potential of −0.664 V versus Ag/AgCl and the lower corrosion current density of 4.41 × 10^-6 A/cm².     

Structural,electric modulus and complex impedance analysis of ZnO/TiO2 composite ceramics

ZnO/TiO₂ composite ceramics have been prepared by solid‐state reaction technique at 900°C. The X‐ray diffraction results revealed the formation of secondary phases referred to as spinel Zn₂TiO₄ and hexagonal ZnTiO₃. The structural analysis showed that all the composites that have been prepared have a polycrystalline nature and a hexagonal wurtzite structure. The complex modulus (M) and electric impedance of the samples have been investigated by broadband dielectric spectroscopy in a wide range of temperature (40°C‐110°C) and frequency (0.1 Hz to 10 MHz). The modulus plots (M′′, M′) illustrate the presence of non‐Debye type of relaxations attributed to the effects of interfacial and dipolar polarizations. The real and the imaginary parts of the impedance are well fitted to equivalent circuit models. At high temperatures, Z″_max varies from 0.03 × 10⁶ to 4.9 × 10⁶ Ω when the TiO₂ doping concentration increases from 1 to 7 wt%. From the obtained results, the secondary phase ZnTiO₃ plays an important role in the electrical properties.