Double Yielding in Injection‐Molded Polycarbonate/Polyethylene Blends: Composition Dependence

Summary: A fiber‐dependent double yielding phenomenon was recently observed in a structurally different blend, PC/HDPE, in which the first yield point is yielding of HDPE, and the second is caused by the yielding of injection‐induced PC fibers. The present study described the composition dependence of the double yielding in PC/HDPE blends with PC contents ranging from 0 to 45 wt.‐%. Morphology observation indicated that the injection‐molded PC/HDPE blends displayed a typical skin‐core structure with more or less injection‐induced elongated PC particles in the sub‐skin layers, and spherical PC particles in the core layers. Stress‐strain curves indicated that the blends with PC contents from 10 to 20 wt.‐% exhibit double yielding behavior and the cold drawing zone after the second yield point shortens with increasing PC content. The blends with too low‐ or too high‐PC contents exhibited only one yield point. Scanning electronic microscope micrographs of the blend with 15 wt.‐% PC showed that when the strain was beyond the first yield point the PC fibers notably yielded and even were broken, which served as an evidence that the yielding of PC phase was responsible for the second yielding. The origin of the composition dependence of the double yielding was discussed in detail through the interfacial stress transfer.

Representative stress‐strain curves for PE10, PE15, PE17.5, and PE20.     

Radiation effects on HDPE/EVA blends

In this article, we discuss the radiation effects of high‐density polyethylene (HDPE)/ethylene–vinyl acetate (EVA) copolymer blends. In comparison with the low‐density polyethylene/EVA blends, the EVA content in the HDPE/EVA blends had a lower enhancement effect on radiation crosslinking by γ‐ray irradiation in air. The phenomenon is discussed with the compatibility, morphology, and thermal properties of HDPE/EVA blends. The HDPE/EVA blends were partly compatible in the amorphous region, and radiation crosslinking of the HDPE/EVA blend was less significant, although increasing the amorphous region's content of the HDPE/EVA blends and the vinyl acetate content of EVA were beneficial to radiation crosslinking. The good compatibility was a prerequisite for the enhancement effect of EVA on the radiation crosslinking of the polyethylene/EVA copolymer. The radiation crosslinking and the degradation mechanism of HDPE/EVA blends were examined quantitatively by a novel method, the step analysis process of irradiated HDPE/EVA blends with a thermal gravimetric analysis technique. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 553–558, 2002     

Dynamic mechanical behavior of high‐density polyethylene/ethylene vinyl acetate copolymer blends: The effects of the blend ratio,reactive compatibilization,and dynamic vulcanization

The effects of the blend ratio, reactive compatibilization, and dynamic vulcanization on the dynamic mechanical properties of high‐density polyethylene (HDPE)/ethylene vinyl acetate (EVA) blends have been analyzed at different temperatures. The storage modulus of the blend decreases with an increase in the EVA content. The loss factor curve shows two peaks, corresponding to the transitions of HDPE and EVA, indicating the incompatibility of the blend system. Attempts have been made to correlate the observed viscoelastic properties of the blends with the blend morphology. Various composite models have been used to predict the dynamic mechanical data. The experimental values are close to those of the Halpin–Tsai model above 50 wt % EVA and close to those of the Coran model up to 50 wt % EVA in the blend. For the Takayanagi model, the theoretical value is in good agreement with the experimental value for a 70/30 HDPE/EVA blend. The area under the loss modulus/temperature curve (LA) has been analyzed with the integration method from the experimental curve and has been compared with that obtained from group contribution analysis. The LA values calculated with group contribution analysis are lower than those calculated with the integration method. The addition of a maleic‐modified polyethylene compatibilizer increases the storage modulus, loss modulus, and loss factor values of the system, and this is due to the finer dispersion of the EVA domains in the HDPE matrix upon compatibilization. For 70/30 and 50/50 blends, the addition of a maleic‐modified polyethylene compatibilizer shifts the relaxation temperature of both HDPE and EVA to a lower temperature, and this indicates increased interdiffusion of the two phases at the interface upon compatibilization. However, for a 30/70 HDPE/EVA blend, the addition of a compatibilizer does not change the relaxation temperature, and this may be due to the cocontinuous morphology of the blends. The dynamic vulcanization of the EVA phase with dicumyl peroxide results in an increase in both the storage and loss moduli of the blends. A significant increase in the relaxation temperature of EVA and a broadening of the relaxation peaks occur during dynamic vulcanization, and this indicates the increased interaction between the two phases. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 2083–2099, 2003     

Rheological behavior comparison between PET/HDPE and PC/HDPE microfibrillar blends

The rheological behaviors of in situ microfibrillar blends, including a typical semicrystalline/semicrystalline (polyethylene terephthalate (PET)/high‐density polyethylene (HDPE)) and a typical amorphous/semicrystalline (polycarbonate (PC)/HDPE) polymer blend were investigated in this study. PET and PC microfibrils exhibit different influences on the rheological behaviors of microfibrillar blends. The viscosity of the microfibrillar blends increases with increased PET and PC concentrations. Surprisingly, the length/diameter ratio of the microfibrils as a result of the hot stretch ratio (HSR) has an opposite influence on the rheological behavior of the two microfibrillar blends. The stretched PET/HDPE blend exhibits higher viscosity than the unstretched counterpart, while the stretched PC/HDPE blend exhibits lower viscosity than the unstretched blend. The data obtained in this study will be helpful for constructing a technical foundation for the recycling and utilization of PET, PC, and HDPE waste mixtures by manufacturing microfibrillar blends in the future. POLYM. ENG. SCI., 45:1231–1238, 2005. © 2005 Society of Plastics Engineers     

Electrical properties and morphology of carbon black‐filled HDPE/EVA composites

The sensitive effect of weight ratio of the high‐density polyethylene (HDPE)/ethylene‐vinylacetate copolymer (EVA) on the electrical properties of HDPE/EVA/carbon black (CB) composites was investigated. With the EVA content increasing from 0 wt % to 100 wt %, an obvious change of positive temperature coefficient (PTC) curve was observed, and a U‐shaped insulator‐conductor‐insulator transition in HDPE/EVA/CB composites with a CB concentration nearby the percolation threshold was found. The selective location of CB particles in HDPE/EVA blend was analyzed by means of theoretical method and scanning electron micrograph (SEM) in order to explain the U‐shaped insulator‐conductor‐insulator transition, a phenomenon different from double percolation in this composite. The first significant change of the resistivity, an insulator‐conductor transition, occurred when the conductive networks diffused into the whole matrix due to the forming of the conductive networks and the continuous EVA phase. The second time significant change of the resistivity, a conductor‐insulator transition, appeared when the amorphous phase is too large for CB particles to form the conductive networks throughout the whole matrix. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of the high‐density polyethylene melt index on the microcellular foaming of high‐density polyethylene/polypropylene blends

The effect of high‐density polyethylene (HDPE)/polypropylene (PP) blending on the crystallinity as a function of the HDPE melt index was studied. The melting temperature and total amount of crystallinity in the HDPE/PP blends were lower than those of the pure polymers, regardless of the blend composition and melt index. The effects of the melt index, blending, and foaming conditions (foaming temperature and foaming time) on the void fractions of HDPEs of various melt indices and HDPE/PP blends were also investigated. The void fraction was strongly dependent on the foaming time, foaming temperature, and blend composition as well as the melt index of HDPE. The void fraction of the foamed 30:70 HDPE/PP blend was always higher than that of the foamed 50:50 HDPE/PP blend, regardless of the melt index. The microcellular structure could be greatly improved with a suitable ratio of HDPE to PP and with foaming above the melting temperature for long enough; however, using high‐melt‐index HDPE in the HDPE/PP blends had a deleterious effect on both the void fraction and cell morphology of the blends. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 364–371, 2004     

PA6／HDPE／EVA三元共混改性的研究

研究了PA6/HDPE、PA6/HDPE/EVA共混物的密度、热性能和力学性能。PA6/HDPE/EVA三元共混物的力学性能比PA6/HDPE二元共混物有明显提高。对于拉伸强度,EVA的最佳含量在2～4份。冲击强度随EVA含量的增加而提高,EVA的含量小于5份时,对共混物的硬度几乎没有影响。     

Investigations of environmental stress cracking resistance of HDPE/EVA and LDPE/EVA blends

HDPE/poly(ethylene‐co‐vinylacetate) (EVA) and low‐density polyethylene (LDPE)/EVA blends were tested and compared with respect to their environmental stress cracking resistance (ESCR) using the Bell‐telephone test. The time to failure in the ESCR test improves with increasing EVA content, and considerable improvements were produced for LDPE/EVA blends while small improvements were observed for HDPE/EVA blends. Thermal, rheological, mechanical, and morphological studies were conducted which established a quantitative relationship between morphological features and composition. Furthermore, the failed specimens were further characterized by scanning electron microscopy and fractographic methodology to investigate the failure mechanism for ESCR samples. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39880.     

Influence of crosslinking on crystallization,rheological, and mechanical behaviors of high density polyethylene/ethylene‐vinyl acetate copolymer blends

High density polyethylene (HDPE)/ethylene‐vinyl acetate copolymer (EVA) blends with selective crosslinking the EVA phase were prepared and the crystallization, rheological, and mechanical behaviors were studied. Selective crosslinking of EVA component could greatly improve both tensile and impact strengths of the HDPE‐rich blends and influence melting enthalpy at different annealing temperature in successive self‐nucleation and annealing procedure. Dynamic mechanical analysis reveals that glass transition temperatures of both the HDPE and EVA components are lowered upon blending and are raised upon crosslinking. The uncrosslinked HDPE/EVA blends are unstable in the melt and show increment in storage modulus (G′) and decay in loss tangent (tanδ) with annealing time associated with phase coarsening. However, morphology of selectively crosslinked blends in the melt state is highly unstable, characterized by a fast migration of uncrosslinked HDPE component out of the crosslinked EVA phase to the surface resulting in a rapid decay in G′ and an increment in tanδ at the early stage of annealing. POLYM. ENG. SCI., 54:2848–2858, 2014. © 2014 Society of Plastics Engineers     

Ethylene vinyl acetate/ethylene propylene diene terpolymer‐blend‐layered double hydroxide nanocomposites

Ethylene vinyl acetate (EVA‐45)/ethylene propylene diene terpolymer (EPDM) blend‐layered double hydroxide (LDH) nanocomposites have been prepared by solution blending of 1:1 weight ratio of EVA and EPDM with varying amounts of organo LDH (DS‐LDH). X‐ray diffraction and transmission electron microscopy analysis suggest the formation of partially exfoliated EVA/EPDM/DS‐LDH nanocomposites. Measurement of mechanical properties of the nanocomposites (3 wt% DS‐LDH content) show that the improvement in tensile strength and elongation at break are 35 and 12% higher than neat EVA/EPDM blends. Dynamic mechanical thermal analysis also shows that the storage modulus of the nanocomposites at glass transition temperature is higher compared to the pure blend. Such improvements in mechanical properties have been correlated in terms of fracture behavior of the nanocomposites using scanning electron microscopy analysis. Thermal stability of the prepared nanocomposites is substantially higher compared to neat EVA/EPDM blend, confirming the formation of high‐performance polymer nanocomposites. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Melt rheology of HDPE/EVA blends: The effects of blend ratio,compatibilization, and dynamic vulcanization

The melt rheological behavior of high‐density polyethylene (HDPE)/ethylene vinyl acetate (EVA) blends has been examined with reference to the effect of blend ratio, shear stress, and temperature. The HDPE/EVA blends exhibit pseudoplastic behavior, and the observed rheological behavior of the blends was correlated with the extrudate morphology. The experimental values of the viscosity were compared with the theoretical models. The effect of maleic‐ and phenolic‐modified PE compatibilizers on the viscosity of H₇₀ blend was analyzed and found that compatibilization did not significantly increase the viscosity. The effect of dynamic vulcanization and temperature on the viscosity was also analyzed. The activation energy of the system decreased with increase in EVA content in the system. The phase continuity and phase inversion points of the blends were theoretically predicted and compared with the experimental values. The melt flow index (MFI) values of the blends were also determined and found that the MFI values decreased with increase in EVA content in the system. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers     

Orientation effects on the deformation and fracture properties of high‐density polyethylene/ethylene vinyl acetate (HDPE/EVA) blends

In this paper, the tensile deformation and fracture toughness of high‐density polyethylene (HDPE)/ethylene vinyl acetate (EVA) blends, obtained by dynamic packing injection moulding, have been comprehensively investigated in different directions of rectangle samples, including longitudinal, latitudinal and oblique directions relative to the flow direction. Two kinds of EVA were used with VA content 16 wt% (16EVA) and 33 wt% (33EVA) to control the interfacial interactions. The results indicate that molecular orientation and interfacial interaction play very important roles to determine the tensile behaviour and fracture toughness. Biaxial‐reinforcement of tensile strength was seen for HDPE/16EVA blends but only uniaxial‐reinforcement was observed for HDPE/33EVA blends. The difference is caused by the different interfacial interactions as highlighted by the peel test, scanning electron microscopy (SEM) observation as well as theoretical evaluation. Very high impact strength, decreasing with increasing EVA content, was observed when the fracture propagation is perpendicular to the shear flow direction, while a low impact strength, increasing slightly increasing with EVA content, was seen when the fracture propagation is parallel to the shear flow. The fracture of oblique samples is always along the flow direction instead of along the impact direction or tensile direction. The tensile behaviour and fracture toughness are discussed on the basis of the formation of transcrystalline zones, orientation of EVA particles and matrix toughness of HDPE in different directions. Copyright © 2004 Society of Chemical Industry     

Toughening and compatibilization of polypropylene/polyamide‐6 blends with a maleated–grafted ethylene‐co‐vinyl acetate

In this article, maleated–grafted ethylene‐co‐vinyl acetate (EVA‐g‐MA) was used as the interfacial modifier for polypropylene/polyamide‐6 (PP/PA6) blends, and effects of its concentration on the mechanical properties and the morphology of blends were investigated. It was found that the addition of EVA‐g‐MA improved the compatibility between PP and PA6 and resulted in a finer dispersion of dispersed PA6 phase. In comparison with uncompatibilized PP/PA6 blend, a significant reduction in the size of dispersed PA6 domain was observed. Toluene‐etched micrographs confirmed the formation of interfacial copolymers. Mechanical measurement revealed that the addition of EVA‐g‐MA markedly improved the impact toughness of PP/PA6 blend. Fractograph micrographs revealed that matrix shear yielding began to occur when EVA‐g‐MA concentration was increased upto 18 wt %. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99:3300–3307, 2006     

Thermostimulative shape‐memory effect of reactive compatibilized high‐density polyethylene/poly(ethylene terephthalate) blends by an ethylene–butyl acrylate–glycidyl methacrylate terpolymer

High‐density polyethylene (HDPE)/poly(ethylene terephthalate) (PET) blends were prepared by means of melt extrusion with ethylene–butyl acrylate–glycidyl methacrylate terpolymer (EBAGMA) as a reactive compatibilizer. The effects of the EBAGMA and PET contents, recovery temperature, and stretch ratio on the thermostimulative shape‐memory behavior of the blends were studied. The results show that the addition of EBAGMA to the HDPE/PET blends obviously improved the compatibility and the shape‐memory effects of the blends. The response temperature was determined by the melting point of HDPE, and the shape‐recovery ratio of the 90/10/5 HDPE/PET/EBAGMA blend reached nearly 100%. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of the particle size of expandable graphite on the thermal stability,flammability, and mechanical properties of high‐density polyethylene/ethylene vinyl‐acetate/expandable graphite composites

In this article, high‐density polyethylene/ethylene vinyl‐acetate copolymer (HDPE/EVA) composites filled with two different particle sizes (45 and 150 µm) of expandable graphite (EG) were prepared by using a twin‐screw extruder. The thermal stability, flammability, and mechanical properties of HDPE/EVA/EG composites were investigated by thermogravimetric analysis (TGA), cone calorimeter test (CCT), tensile test, and scanning electron microscopy (SEM). The results from TGA and CCT indicated that EG significantly enhanced the thermal stability and fire resistance of HDPE/EVA blend. The thermal stability and flame retardancy of HDPE/EVA/EG composites were improved with decreasing particle size of EG. Although the onset of weight loss of the flame‐retardant composites occurred at a lower temperature than that of HDPE/EVA blend, the flame‐retardant composites produced a large amount of char residue at a high temperature. The consolidated char layer formed a barrier, which could reduce heat, low‐molecular transfer, and air incursion, and thus enhanced the flame retardancy. The data from the tensile test showed that the addition of EG deteriorated the mechanical properties; however, the tensile stress and strain of HDPE/EVA/EG composites increased with decreasing the particle size of EG owing to the strong interface adhesion between polymer matrix and inorganic particles. POLYM. ENG. SCI., 54:1162–1169, 2014. © 2013 Society of Plastics Engineers     

Influence of coalescence and interfacial tension on the morphology of PP/HDPE compatibilized blends

In this paper, the compatibilization of polypropylene (PP)/high-density polyethylene (HDPE) blend was studied through morphological and interfacial tension analysis. Three types of compatibilizers were tested: ethylene-propylene-diene copolymer (EPDM), ethylene-vinylacetate copolymer (EVA) and styrene-ethylene/butylene-styrene triblock copolymer (SEBS). The morphology of the blends was studied by scanning electron microscopy. The interfacial tension between the components of the blends was evaluated using small amplitude oscillatory shear analysis. Emulsion curves relating the average radius of the dispersed phase and the interfacial tension to the compatibilizer concentration added to the blend were obtained. It was shown that EPDM was more efficient as an emulsifier for PP/HDPE blend than EVA or SEBS. The relative role of interfacial tension reduction and coalescence reduction to particle size reduction was also addressed. It was observed that the role of coalescence reduction is small, mainly for PP/HDPE (90/10) blends compatibilized by EPDM, EVA or SEBS. The results indicated that the role of coalescence reduction to particle size reduction is lower for blends for which interfacial tension between its components is low at compatibilizer saturation.     

HDPE/PC/EVA共混体系的性能研究

研究了乙烯-醋酸乙烯共聚物(EVA)增容高密度聚乙烯(HDPE)和聚碳酸酯(PC)共混体系，讨论了EVA，PC对HDPE／PC共混合金性能的影响。结果表明：随PC用量的增加，HDPE／PC共混合金的熔体流动速率减小，缺口冲击强度增大，拉伸强度增大，维卡软化点变化不大。EVA能够改善合金体系的加工流动性，却明显降低了合金体系的力学性能。     

Morphology and Rheological Behaviors of Polycarbonate/High Density Polyethylene in situ Microfibrillar Blends

Summary: Polycarbonate (PC)/high density polyethylene (HDPE) in situ microfibrillar blends were fabricated by a slit die extrusion, hot stretching, and quenching process. Despite PC and HDPE having a high viscosity ratio, which is usually disadvantageous to fibrillation, the morphological observation indicated that the blends had well‐defined PC microfibrils. The size and amount of the PC fibrils were nonuniform through the thickness of the extrudate, and were also affected by the PC concentration and hot stretch ratio. There were coarse and dense fibrils in the core zone, while these fibrils became finer and reduced in number toward the surface. The melt flow rate (MFR) of the PC/HDPE microfibrillar blend decreased with the increase of PC concentration, but increased with the larger hot stretching rate (or hot stretching ratio, HSR). Besides, it was found that the fibrillar blend had better flowability than the common blend with spherical particles at the same PC concentration. Temperature was also an important factor influencing the MFR due to the temperature dependence of PC and HDPE viscosity, and the PC phase morphology. The PC microfibrils could not be preserved beyond 230 °C and transformed into spherical particles. The rheological behaviors at various shear rates were studied by capillary rheometer. The orientation of PC fibrils and HDPE molecules with higher shear rate led to a decrease in the viscosity of microfibrillar blend. The data obtained in this study can help construct the technical foundation for recycling and utilization of PC and HDPE waste by manufacture of microfibrillar blends in future work.

SEM micrograph of the PC/HDPE microfibrillar blend.     

Thermal and mechanical properties of uncrosslinked and chemically crosslinked polyethylene/ethylene vinyl acetate copolymer blends

Uncrosslinked and chemically crosslinked binary blends of low‐ and high‐density polyethylene (PE), with ethylene vinyl acetate copolymer (EVA), were prepared by a melt‐mixing process using 0–3 wt % tert‐butyl cumyl peroxide (BCUP). The uncrosslinked blends revealed two distinct unchanged melting peaks corresponding to the individual components of the blends, but with a reduced overall degree of crystallinity. The crosslinking further reduced crystallinity, but enhanced compatibility between EVA and polyethylene, with LDPE being more compatible than HDPE. Blended with 20 wt % EVA, the EVA melting peak was almost disappeared after the addition of BCUP, and only the corresponding PE melting point was observed at a lowered temperature. But blended with 40% EVA, two peaks still existed with a slight shift toward lower temperatures. Changes of mechanical properties with blending ratio, crosslinking, and temperature had been dominated by the extent of crystallinity, crosslinking degree, and morphology of the blend. A good correlation was observed between elongation‐at‐break and morphological properties. The blends with higher level of compatibility showed less deviation from the additive rule of mixtures. The deviation became more pronounced for HDPE/EVA blends in the phase inversion region, while an opposite trend was observed for LDPE/EVA blends with co‐continuous morphology. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3261–3270, 2007     

Viscoelastic,thermal, and morphological analysis of HDPE/EVA/CaCO<Subscript>3</Subscript> ternary blends

High density polyethylene (HDPE), calcium carbonate (CaCO₃), and ethylene vinyl acetate (EVA) ternary reinforced blends were prepared by melt blend technique using a twin screw extruder. The thermal properties of these prepared ternary blends were investigated by differential scanning calorimetry. The effect of EVA loading on the melting temperature (T _m) and the crystallization temperature (T _C) was evaluated. It was found that the expected heterogeneous nucleating effect of CaCO₃ was hindered due to the presence of EVA. The melt viscosities of the ternary reinforced blends were affected by the % loading of CaCO₃, EVA, and vinyl acetate content. Viscoelastic analysis showed that there is a reduction of the storage modulus (G′) with increasing of EVA loading as compared to neat HDPE resin or to HDPE/CACO₃ blends only. The morphology of the composites was characterized by scanning electron microscopy (SEM). The dispersion and interfacial interaction between CaCO₃ with EVA and HDPE matrix were also investigated by SEM. We observed two main types of phase structures; encapsulation of the CaCO₃ by EVA and separate dispersion of the phases. Other properties of ternary HDPE/CaCO₃/EVA reinforced blends were investigated as well using thermal, rheological, and viscoelastic techniques.