Natural fiber blend—nylon 6 composites

In this study, engineering thermoplastic composites were prepared from natural fiber blend–filled nylon 6. Natural fiber blend from a mixture of kenaf, flax, and hemp fibers were added to nylon 6 using melt mixing to produce compounded pellets. The natural fibers/ nylon6 composites with varying concentrations of natural fibers (from 5 to 20 wt%) were prepared by injection molding. The tensile and flexural properties of the nylon 6 composites were increased significantly with the addition of the natural fiber blend. The maximum strength and modulus of elasticity for the nylon 6 composites were achieved at a natural fiber blend weight fraction of 20%. The Izod impact strength of composites decreased with the incorporation of natural fibers without any surface treatments and coupling agent. The melt flow index (MFI) also decreased with increasing natural fiber blend loading. The results of tensile and flexural modulus of elasticity (FMOE) are in accordance with the rheological data from the MFI measurements. The increase in the tensile and flexural properties indicated that efficient bonding occurred between the natural fibers and nylon 6. No fiber pullout was observed during the scanning electron microscopic analysis of the fracture surfaces. The higher mechanical results with lower density demonstrate that a natural fiber blend can be used as a sufficient reinforcing material for low‐cost, eco‐friendly composites in the automotive industry and in other applications such as the building and construction industries, packaging, consumer products, etc.POLYM. COMPOS., 2013. © 2013 Society of Plastics Engineers     

Non‐traditional lightweight polypropylene composites reinforced with milkweed floss

Lightweight composites are preferred for automotive applications due to the weight restrictions and also due to the presence of inherent voids that can enhance the sound absorption of these composites. The density of the reinforcing materials plays a crucial role in such lightweight composites. Milkweed is a unique natural cellulose fiber that has a completely hollow center and low density (0.9 g cm^?3) unlike any other natural cellulose fiber. The low density of milkweed fibers will allow the incorporation of higher amounts of fiber per unit weight of a composite, which is expected to lead to lightweight composites with better properties. Polypropylene (PP) composites reinforced with milkweed fibers have much better flexural and tensile properties than similar PP composites reinforced with kenaf fibers. Milkweed fiber‐reinforced composites have much higher strength but are stiffer than kenaf fiber‐reinforced PP composites. Increasing the proportion of milkweed in the composites from 35 to 50% increases the flexural strength but decreases the tensile strength. The low density of milkweed fibers allows the incorporation of higher amounts of fibers per unit weight of the composites and hence provides better properties compared to composites reinforced with common cellulose fibers with relatively high density. This research shows that low‐density reinforcing materials can more efficiently reinforce lightweight composites. Copyright © 2010 Society of Chemical Industry     

Unidirectional hemp and flax EP‐ and PP‐composites: Influence of defined fiber treatments

In some technical areas, mainly in the automotive industry, glass fiber reinforced polymers are intended to be replaced by natural fiber reinforced polymer systems. Therefore, higher requirements will be imposed to the physical fiber properties, fiber‐matrix adhesion, and the quality assurance. To improve the properties of epoxy resins (EP) and polypropylene (PP) composites, flax and hemp fibers were modified by mercerization and MAH‐PP coupling agent was used for preparing the PP composites. The effects of different mercerization parameters such as concentration of alkali (NaOH), temperature, and duration time along with tensile stress applied to the fibers on the structure and properties of hemp fibers were studied and judged via the cellulose I–II lattice conversion. It was observed that the mechanical properties of the fibers can be controlled in a broad range by using appropriate mercerization parameters. Unidirectional EP composites were manufactured by the filament winding technique; at the PP matrix material, a combination with a film‐stacking technique was used. The influence of mercerization parameters on the properties of EP composites was studied with hemp yarn as an example. Different macromechanical effects are shown at hemp‐ and flax‐PP model composites with mercerized, MAH‐PP‐treated, or MAH‐PP‐treated mercerized yarns. The composites' properties were verified by tensile and flexural tests. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2150–2156, 2004     

Recent development and future trends in coir fiber‐reinforced green polymer composites: Review and evaluation

Development of natural fiber composites with thermoplastics and thermosets finds applications in various fields, from agriculture to automotive. It can reduce the dependency on petroleum resources which causes several environmental problems. Natural fibers are renewable and biodegradable that reduces carbon footprint to the environment. Coir fibers are natural fibers used in the development of composites offers comparable properties with other mineral fillers. This article reviews different methods of coir fiber modification include alkali treatment, silane treatment, hydrogen peroxide treatment, sodium hypochlorite treatment, sodium periodate treatment coupled with p‐aminophenol and urea, treatment with benzene diazonium salt and maleated coupling agent. It also reviews composites of coir fiber with thermoplastic, rubber and thermoset plastics. Hybrid composites based on coir fiber are also being discussed. Thermoplastic composites such as biodegradable (PLA, PBS) and petroleum‐based polymers (PE, PP) and thermoset polymers include polyurethane, epoxy and polyester based composites also reviewed. Degradation and biodegradation studies were reviewed in the case of biodegradable polymers. Hybrid fibers of coir with other natural and mineral fibers have recently been used in composite industry has also been reviewed. All these composites show better properties. It can be used in different applications in the field of automobile, building and construction, consumer products and furniture. POLYM. COMPOS., 37:3296–3309, 2016. © 2015 Society of Plastics Engineers     

Esterification effect of maleic anhydride on swelling properties of natural fiber/high density polyethylene composites

The natural fibers (banana, hemp, and sisal) and high density polyethylene were taken for the preparation of natural fiber/polymer composites in different ratios of 40 : 60 and 45 : 55 (w/w). These fibers were esterified with maleic anhydride (MA) and the effect of esterification of MA was studied on swelling properties in terms of absorption of water, at ambient temperature, and steam. It was found that the steam penetrates more within lesserperiod of time than water at ambient temperature. Untreated fiber composites show more absorption of steam and water in comparison to MA‐treated fiber composites. The more absorption of water was found in hemp fiber composites and less in sisal fiber composites. Steam absorption in MA‐treated and untreated fiber composites are higher than the water absorption in respective fiber composites. The natural fiber/polymer composites containing low amount of fibers show less absorption of steam and water at ambient temperature than the composites containing more amount of fibers in respective fiber composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

A review of aspects affecting performance and modeling of short‐natural‐fiber‐reinforced polymers under monotonic and cyclic loading conditions

The use of short natural fibers as reinforcing fibers was hampered by uncertainties associated with the performance of these developed short‐fiber‐reinforced composites. Much of this uncertainty comes from an unclear understanding of different aspects controlling the properties and the behavior of natural fibers and their developed composites. This study provides a benchmark review that highlights several factors affecting the performance of short‐natural‐fiber‐reinforced polymers (SNFRPs). Additionally, the study also reviews the researches related to the short term (monotonic) and the long‐term (cyclic) behaviors as well as the potential monotonic and life prediction models and techniques suited for SNFRPs. POLYM. COMPOS. 36:397–409, 2015. © 2014 Society of Plastics Engineers     

Mechanical properties of surface‐modified ultra‐high molecular weight polyethylene fiber reinforced natural rubber composites

The mechanical properties of ultra‐high molecular weight polyethylene (UHMWPE) fibers reinforced natural rubber (NR) composites were determined, and the effects of fiber surface treatment and fiber mass fraction on the mechanical properties of the composites were investigated. Chromic acid was used to modify the UHMWPE fibers, and the results showed that the surface roughness and the oxygen‐containing groups on the surface of the fibers could be effectively increased. The NR matrix composites were prepared with as‐received and chromic acid treated UHMWPE fibers added 0–6 wt%. The treated UHMWPE fibers increased the elongation at break, tear strength, and hardness of the NR composites, especially the tensile stress at a given elongation, but reduced the tensile strength. The elongation at break increased markedly with increasing fiber mass fraction, attained maximum values at 3.0 wt%, and then decreased. The tear strength and hardness exhibited continuous increase with increasing the fiber content. Several microfibrillations between the fiber and NR matrix were observed from SEM images of the fractured surfaces of the treated UHMWPE fibers/NR composites, which meant that the interfacial adhesion strength was improved. POLYM. COMPOS., 38:1215–1220, 2017. © 2015 Society of Plastics Engineers     

Physical and mechanical behavior of unidirectional banana/jute fiber reinforced epoxy based hybrid composites

During the last few years, natural fiber composites are replacing synthetic fiber composites for practical applications due to their advantages like low density, light weight, low cost, biodegradability and high specific mechanical properties. In this connection, the present investigation deals with the fabrication and mechanical properties of unidirectional banana/jute hybrid fiber reinforced composites and compares with the single natural fiber reinforced composites. The physical and mechanical properties of the natural fiber composites were obtained by testing the composite for density, tensile, flexural, inter‐laminar shear, impact, and hardness properties. The composite specimens with different weight percentages of fibers were fabricated by using hand lay‐up technique and testing were carried out as per ASTM standards. Incorporation of both the fibers into epoxy matrix resulted in an increase in mechanical properties up to 30 wt% of fiber loading. It is found that the hybrid composite give encouraging results when compared with the individual fiber composites. The morphologies of the composites are also studied by scanning electron microscope. POLYM. COMPOS., 38:1396–1403, 2017. © 2015 Society of Plastics Engineers     

Polyamide‐6 composites reinforced with cellulose fibers and fabricated by extrusion: Effect of fiber bleaching on mechanical properties and stability

We prepared polyamide‐6 (PA‐6) composites using bleached and semibleached cellulose fibers from Eucalyptus species by processing in a corotating interpenetrating twin‐screw extruder. PA‐6 is a challenging matrix because of its high processing temperature, which overlaps the thermodegradation temperature of the fibers. The selection of the processing conditions for extrusion and the use of the lubricant ethylene bis (stearamide) permitted the production of composites with 20, 30, and 40 wt% of bleached fibers, which are lighter than the corresponding glass fiber composites. Composites with 30 wt% of bleached fibers yield the best mechanical properties and good fiber/matrix interaction, as demonstrated by mechanical tests and scanning electron microscopy. X‐ray photoelectron spectroscopy studies showed that the natural moisture in the fibers promotes the fiber/matrix interaction through the formation of ester bonds. We assessed the effect caused by the presence of lignin in the fibers. Composites containing 30 wt% of semibleached fibers maintained the flexural properties and showed small improvements in thermal stability when compared with bleached fiber composites; however, there is a slight decrease in the tensile properties. Through accelerated aging tests, we observed that increased lignin concentration in the fibers reduced the formation of carbonyl compounds on sample surfaces, indicating a stabilization effect. POLYM. COMPOS., 38:299–308, 2017. © 2015 Society of Plastics Engineers     

Dynamic mechanical properties of oil palm microfibril‐reinforced natural rubber composites

The dynamic mechanical properties of macro and microfibers of oil palm‐reinforced natural rubber (NR) composites were investigated as a function of fiber content, temperature, treatment, and frequency. By the incorporation of macrofiber to NR, the storage modulus (E') value increases while the damping factor (tan δ) shifts toward higher temperature region. As the fiber content increases the damping nature of the composite decreases because of the increased stiffness imparted by the natural fibers. By using the steam explosion method, the microfibrils were separated from the oil palm fibers. These fibers were subjected to treatments such as mercerization, benzoylation, and silane treatment. Resorcinol‐hexamethylenetetramine‐hydrated silica was also used as bonding agent to increase the fiber/matrix adhesion. The storage modulus value of untreated and treated microfibril‐reinforced composites was higher than that of macrofiber‐reinforced composites. The T_g value obtained for this microfibril‐reinforced composites were slightly higher than that of macrofiber‐reinforced composites. The activation energy for the relaxation processes in different composites was also calculated. The morphological studies using scanning electron microscopy of tensile fracture surfaces of treated and untreated composites indicated better fiber/matrix adhesion in the case of treated microfibril‐reinforced composites. Finally, attempts were made to correlate the experimental dynamic properties with the theoretical predictions. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Influence of fiber orientation and fiber content on properties of sisal‐jute‐glass fiber‐reinforced polyester composites

The incorporation of natural fibers with polymer matrix composites (PMCs) has increasing applications in many fields of engineering due to the growing concerns regarding the environmental impact and energy crisis. The objective of this work is to examine the effect of fiber orientation and fiber content on properties of sisal‐jute‐glass fiber‐reinforced polyester composites. In this experimental study, sisal‐jute‐glass fiber‐reinforced polyester composites are prepared with fiber orientations of 0° and 90° and fiber volume of sisal‐jute‐glass fibers are in the ratio of 40:0:60, 0:40:60, and 20:20:60 respectively, and the experiments were conducted. The results indicated that the hybrid composites had shown better performance and the fiber orientation and fiber content play major role in strength and water absorption properties. The morphological properties, internal structure, cracks, and fiber pull out of the fractured specimen during testing are also investigated by using scanning electron microscopy (SEM) analysis. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42968.     

Preparation and mechanical characterization of chicken feather/PLA composites

Green composites, a bio‐based polymer matrix is reinforced by natural fibers, are special class of bio‐composites. Interest about green composites is continuously growing because they are environment‐friendly. This study describes the preparation and mechanical characterization of green composites using polylactic acid (PLA) matrix including chicken feather fiber (CFF) as reinforcement. Extrusion and an injection molding process were used to prepare CFF/PLA composites at a controlled temperature range. CFF/PLA composites with fiber mass content of 2%, 5%, and 10% were manufactured. The effects of fiber concentration and fiber length on mechanical properties of CFF/PLA composites have been studied. Mechanical properties of composites were investigated by tensile, compression, bending, hardness, and Izod impact testing. The results of experiments indicated that Young's modulus, compressive strength, flexural modulus, and hardness of the PLA reinforced CFF composites are higher but tensile strength, elongation at break, bending strength and impact strength of them are lower than pure PLA. The results indicate that these types of composites can be used for various applications. POLYM. COMPOS., 38:837–845, 2017. © 2015 Society of Plastics Engineers     

Statistical analysis of the mechanical properties of natural fibers and their composite materials. II. Composite materials

In this study, the tensile behavior of different natural fiber reinforced composite materials were analyzed. The statistical analysis used to study the natural fibers in the first article, has been extended to analyze the behavior of PP‐matrix composites, combining the probability density function estimation of fiber properties with the Halpin‐Tsai equation. In this case, the advanced statistical approach overestimates the mechanical properties of the composites, probably because of the poor matrix‐fiber adhesion between polypropylene and natural fibers in the real system. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Influence of ammonium polyphosphate on the flame retardancy and mechanical properties of ramie fiber‐reinforced poly(lactic acid) biocomposites

Fully degradable natural fiber/degradable polymer composites have received much research attention and have various applications such as in automotive components. But flammability limits their application; it is important to improve the flame retardancy of fully degradable composites with environmentally friendly flame retardants. Flame‐retarded ramie fiber‐reinforced poly(lactic acid) (PLA) composites were prepared using three processes: (1) PLA was blended with ammonium polyphosphate (APP), and then the resulting flame‐retarded PLA was combined with ramie fibers; (2) ramie fibers underwent flame‐retardant treatment with APP, which were then compounded with PLA; and (3) PLA and ramie, both of which had been flame‐retarded using APP, were blended together. The APP in the composites is shown to be very effective in improving flame retardancy according UL94 test and limiting oxygen index measurements. Thermogravimetric analysis shows that the improved flame retardancy is due to increased char residue at high temperature. The loading of APP disturbs the compatibility between PLA and fibers, which can be directly observed using scanning electron microscopy. Furthermore it has an influence on the dynamic mechanical properties and mechanical properties according dynamic mechanical analysis and mechanical measurements. The results show that composites produced using the third process not only have the best flame retardancy but also comparatively better mechanical properties. Copyright © 2009 Society of Chemical Industry     

Curing characteristics and mechanical properties of alkali‐treated grass‐fiber‐filled natural rubber composites and effects of bonding agent

To improve adhesion between fiber and matrix, natural rubber was reinforced with a special type of alkali‐treated grass fiber (Cyperus Tegetum Rox b). The cure characteristics and mechanical properties of grass‐fiber‐filled natural rubber composites with different mesh sizes were studied with various fiber loadings. Increasing the amount of fibers resulted in the composites having reduced tensile strength but increased modulus. The better mechanical properties of the 400‐mesh grass‐fiber‐filled natural rubber composite showed that the rubber/fiber interface was improved by the addition of resorcinol formaldehyde latex (RFL) as bonding agent for this particular formulation. The optimum cure time decreased with increases in fiber loading, but there was no appreciable change in scorch time. Although the optimum cure time of vulcanizates having RFL‐treated fibers was higher than that of the other vulcanizates, it decreased with fiber loading in the presence of RFL as the bonding agent. But this value was lower than that of the rubber composite without RFL. Investigation of equilibrium swelling in a hydrocarbon solvent was also carried out. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3151–3160, 2006     

Preparation and characterization of LDPE and PP—Wood fiber composites

Natural fiber reinforced composites is an emerging area in polymer science. These natural fibers are low cost fibers with low density and high specific properties. These are biodegradable and nonabrasive. The natural fiber composites offer specific properties comparable to those of conventional fiber composites. However, in development of these composites, the incompatibility of the fibers and poor resistance to moisture often reduce the potential of natural fibers, and these draw backs become critical issue. Wood‐plastic composites (WPC) are a relatively new class of materials and one of the fastest growing sectors in the wood composites industry. Composites of wood in a thermoplastic matrix (wood–plastic composites) are considered a low maintenance solution to using wood in outdoor applications. WPCs are normally made from a mixture of wood fiber, thermoplastic, and small amounts of process and property modifiers through an extrusion process. In this study, Wood–plastic composites (WPC) are produce by adding a maleic anhydride modified low density polyethylene coupling agent to improve interfacial adhesion between the wood fiber and the plastic. Mixing is done with twin screw extruder. Subsequently, tensile strength, the modulus of elasticity, % elongation, hardness, Izod impact strength, melt flow index (MFI), and heat deflection temperature (HDT) are determined. Thermal transition temperatures and microstructure are determined with DSC and SEM, respectively. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Pretreatments of natural fibers and their application as reinforcing material in polymer composites—A review

In recent years, natural fibers reinforced composites have received much attention because of their lightweight, nonabrasive, combustible, nontoxic, low cost and biodegradable properties. Among the various natural fibers; flax, bamboo, sisal, hemp, ramie, jute, and wood fibers are of particular interest. A lot of research work has been performed all over the world on the use of natural fibers as a reinforcing material for the preparation of various types of composites. However, lack of good interfacial adhesion, low melting point, and poor resistance towards moisture make the use of natural fiber reinforced composites less attractive. Pretreatments of the natural fiber can clean the fiber surface, chemically modify the surface, stop the moisture absorption process, and increase the surface roughness. Among the various pretreatment techniques, graft copolymerization and plasma treatment are the best methods for surface modification of natural fibers. Graft copolymers of natural fibers with vinyl monomers provide better adhesion between matrix and fiber. In the present article, the use of pretreated natural fibers in polymer matrix‐based composites has been reviewed. Effect of surface modification of natural fibers on the properties of fibers and fiber reinforced polymer composites has also been discussed. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Use of wet‐laid techniques to form flax‐polypropylene nonwovens as base substrates for eco‐friendly composites by using hot‐press molding

The wet‐laid process with flax (base) and polypropylene (binder) fibers has been used to obtain nonwovens for further processing by hot‐press molding. Mechanical characterization of nonwovens has revealed that slight anisotropy is obtained with the wet‐laid process as better tensile strength is obtained in the preferential deposition direction. The thermo‐bonding process provides good cohesion to nonwovens, which is critical for further handling/shaping by hot‐press molding. Flax:PP composites have been processed by stacking eight individual flax:PP nonwoven sheets and applying moderate temperature and pressure. As the amount of binder fiber is relatively low (<30 wt%) if compared with similar systems processed by extrusion and injection molding, it is possible to obtain eco‐friendly composites as the total content on natural fiber (flax) is higher than 70 wt%. Mechanical characterization of hot‐pressed flax:PP composites has revealed high dependency of tensile and flexural strength on the total amount of binder fiber as this component is responsible for flax fiber embedment which is a critical parameter to ensure good fiber–matrix interaction. Combination of wet‐laid techniques with hot‐press molding processes is interesting from both technical and environmental points of view as high natural fiber content composites with balanced properties can be obtained. POLYM. COMPOS., 2012. © 2011 Society of Plastics Engineers     

Interfacial contributions in lignocellulosic fiber‐reinforced polyurethane composites

Whereas lignocellulosic fibers have received considerable attention as a reinforcing agent in thermoplastic composites, their applicability to reactive polymer systems remains of considerable interest. The hydroxyl‐rich nature of natural lignocellulosic fibers suggests that they are particularly useful in thermosetting systems such as polyurethanes. To further this concept, urethane composites were prepared using both unused thermomechanical pulp and recycled newsprint fibers. In formulating the materials, the fibers were considered as a pseudo‐reactant, contributing to the network formation. A di‐functional and tri‐functional poly(propylene oxide)‐based polyol were investigated as the synthetic components with a polyol‐miscible isocyanate resin serving as a crosslinking agent. The mechanical properties of the composites were found to depend most strongly on the type of fiber, and specifically the accessibility of hydroxy functionality on the fiber. Dynamic mechanical analysis, swelling behavior, and scanning electron micrographs of failure surfaces all provided evidence of a substantial interphase in the composites that directly impacted performance properties. The functionality of the synthetic polyol further distinguished the behavior of the composite materials. Tri‐functional polyols generally increased strength and stiffness, regardless of fiber type. The data suggest that synthetic polyol functionality and relative accessibility of the internal polymer structure of the fiber wall are dominant factors in determining the extent of interphase development. Considerable opportunity exists to engineer the properties of this material system given the wide range of natural fibers and synthetic polyols available for formulation. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 546–555, 2001     

Extraction of fibers from saccharum munja grass and its application in composites

With growing environmental awareness, ecological concerns and new legislations, natural fiber‐reinforced plastic composites have received increasing attention during the recent decades. The natural fiber composites have many advantages over traditional glass fiber composites, including lower cost, lighter weight, environmental friendliness, and recyclability. This article reports the findings of the studies done on a new fiber, hitherto unexplored, extracted from Saccharum munja grass. The extracted fibers were further treated using sodium hydroxide to improve its performance in composites. Both treated and untreated fiber‐reinforced composites were prepared by hand lay‐up process using unsaturated polyester resin. Mechanical properties and thermal behavior of the composites were evaluated. The improvement in properties was found for alkali‐treated fiber composites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40829.