Effects of olefin‐based compatibilizers on the morphology,thermal and mechanical properties of ABS/polyamide‐6 blends

In this study, commercially available epoxidized and maleated olefinic copolymers, EMA‐GMA (ethylene‐methyl acrylate‐glycidyl methacrylate) and EnBACO‐MAH (ethylene‐n butyl acrylate‐carbon monoxide‐maleic anhydride), were used at 0, 5, and 10% by weight to compatibilize the blend composed of ABS (acrylonitrile‐butadiene‐styrene) terpolymer and PA6 (polyamide 6). Compatibilizing performance of these two olefinic polymers was investigated from blend morphologies, thermal and mechanical properties as a function of blend composition, and compatibilizer loading level. Scanning electron microscopy (SEM) studies showed that incorporation of compatibilizer resulted in a fine morphology with reduced dispersed particle diameter at the presence of 5% compatibilizer. The crystallization behavior of PA6 phase in the blends was explored for selected blend compositions by differential scanning calorimetry (DSC). At high compatibilizer level a decrease in the degree of crystallization was observed. In 10% compatibilizer containing blends, formation of γ‐crystals was observed contrary to other compatibilizer compositions. The behavior of the compatibilized blend system in tensile testing showed the negative effect of using excess compatibilizer. Different trends in yield strengths and strain at break values were observed depending on compatibilizer type, loading level, and blend composition. With 5% EnBACO‐MAH, the blend toughness was observed to be the highest at room temperature. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 926–935, 2007     

Toughening and compatibilization of polypropylene/polyamide‐6 blends with a maleated–grafted ethylene‐co‐vinyl acetate

In this article, maleated–grafted ethylene‐co‐vinyl acetate (EVA‐g‐MA) was used as the interfacial modifier for polypropylene/polyamide‐6 (PP/PA6) blends, and effects of its concentration on the mechanical properties and the morphology of blends were investigated. It was found that the addition of EVA‐g‐MA improved the compatibility between PP and PA6 and resulted in a finer dispersion of dispersed PA6 phase. In comparison with uncompatibilized PP/PA6 blend, a significant reduction in the size of dispersed PA6 domain was observed. Toluene‐etched micrographs confirmed the formation of interfacial copolymers. Mechanical measurement revealed that the addition of EVA‐g‐MA markedly improved the impact toughness of PP/PA6 blend. Fractograph micrographs revealed that matrix shear yielding began to occur when EVA‐g‐MA concentration was increased upto 18 wt %. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99:3300–3307, 2006     

Study on morphology of compatibilized poly (vinyl chloride)/ultrafine polyamide‐6 blends by styrene–maleic anhydride

Ultrafine polyamide‐6 (UPA6) with a size of 4–8 μm was prepared via jet‐milling. Blends of poly (vinyl chloride) (PVC) and UPA6 using a reactive copolymer styrene–maleic anhydride (SMA‐18%) were prepared. The change in morphology and structure of the blends were studied using differential scanning calorimetry, scanning electron microscopy, and X‐ray diffraction. The blend behavior was also determined experimentally using dynamic mechanical analysis. Contrasted to the original PA6, the crystallinity of the UPA6 decreased, the size of its crystallites were reduced, and its melting point decreased to 175°C. In all blends, PVC formed the continuous matrix phase. SMA is miscible with PVC and tends to be dissolved in the PVC phase during the earlier stages of blending. The dissolved SMA has the opportunity to react with PA6 at the interface to form the desirable SMA‐g‐PA6 copolymer. This in situ formed SMA‐g‐PA6 graft copolymer tends to anchor along the interface to reduce the interfacial tension and results in finer phase domains. Cocrystallity existed in PVC/(UPA6/SMA) at a ratio of 82/(18/5). © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 850–854, 2005     

A study on the effects of SEBS‐g‐MAH on the phase morphology and mechanical properties of polypropylene/polycarbonate/SEBS ternary polymer blends

In this work, five ternary blends based on 70% by weight (wt %) of polypropylene (PP) with 30% wt of polycarbonate (PC)/poly(styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene)(SEBS) dispersed phase consists of 15 wt % PC and 15 wt % reactive (maleic anhydride grafted) and nonreactive SEBS mixtures at various ratios were prepared in a co‐rotating twin screw extruder. scanning electron microscopy (SEM) micrographs showed that the blends containing only nonreactive SEBS exhibited a fine dispersion of core‐shell particles. With decreasing the SEBS/SEBS‐g‐Maleic Anhydride (MAH) weight ratio, the morphology changed from the core‐shell particles to a mixed of core‐shell, rod‐like and individual particles. This variation in phase morphology affected the thermal and mechanical properties of the blends. DSC results showed that the blends containing only nonreactive SEBS exhibited a minimum in degree of crystallinity due to the homogeneous nucleation of core‐shell particles. Mechanical testing showed that in the SEBS/SEBS‐g‐MAH weight ratio of 50/50, the modulus and impact strength increased compared with the PP matrix while the yield stress had minimum difference with that of PP matrix. These effects could be attributed to the formation of those especial microstructures revealed by the SEM studies. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Morphology and mechanical properties of PVC/straw‐fiber coated with liquid nitrile‐butadiene rubber composites

This study exhibited an approach of high‐value utilization of straw fiber (SF) in polymer composites. The rigid poly(vinyl chloride) [PVC]/SF and PVC/SF coated with liquid nitrile‐butadiene rubber (PVC/LNBR‐SF) composites were both fabricated by melt mixing. The chemical structure and crystal structure of LNBR‐SF were characterized by Fourier Transform Infrared Spectroscopy (FTIR) and X‐ray diffraction (XRD). The mechanical properties and micro‐structure of PVC/SF and PVC/LNBR‐SF composites were also studied. FTIR and XRD results showed that the chemical structure and crystal structure of SF did not change after modifying with LNBR. The mechanical properties analysis showed that the PVC/LNBR‐SF composites exhibited better tensile strength, elongation at break and notched impact strength than those of PVC/SF composites owing to the compatibilization and toughening effect of LNBR. Scanning electron microscope results indicated that the LNBR improved the dispersion of SF in PVC matrix to some extent. The interface adhesion between SF and PVC matrix with adding LNBR was also enhanced. These results suggested that PVC/LNBR‐SF composites exhibited promising potential for practical application in substitute for wood. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44119.     

Study on the microstructures and mechanical behaviour of compatibilized polypropylene/polyamide‐6 blends

A series of blends of polypropylene (PP)–polyamide‐6 (PA6) with either reactive polyethylene–octene elastomer (POE) grafted with maleic anhydride (POE‐g‐MA) or with maleated PP (PP‐g‐MA) as compatibilizers were prepared. The microstructures and mechanical properties of the blends were investigated by means of tensile and impact testing and by scanning electron microscopy and transmission electron microscopy. The results indicated that the miscibility of PP–PA6 blends was improved with the addition of POE‐g‐MA and PP‐g‐MA. For the PP/PA6/POE‐g‐MA system, an elastic interfacial POE layer was formed around PA6 particles and the dispersed POE phases were also observed in the PP matrix. Its Izod impact strength was four times that of pure PP matrix, whilst the tensile strength and Young's modulus were almost unchanged. The greatest tensile strength was obtained for PP/PA6/PP‐g‐MA blend, but its Izod impact strength was reduced in comparison with the pure PP matrix. © 2002 Society of Chemical Industry     

Artificial weathering effect on the structure and properties of polypropylene/polyamide‐6 blends compatibilized with PP‐g‐MA

The degradation of uncompatibilized and compatibilized PP/PA‐6 (70/30 wt %) with PP‐g‐MA under accelerated UV light was investigated using Fourier Transform Infrared Spectroscopy (FTIR) spectroscopy, melt flow index (MFI) tester, tensile test, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and scanning electron microscopy (SEM). FTIR analysis of the structure of the compatibilized and uncompatibilized blends after exposure to UV light showed the formation of photoproducts corresponding to both components. The MFI and mechanical results obtained revealed that photooxidation started primarily in PA‐6 rather than PP. In addition, the uncompatibilized blends exhibited a higher degradation rate compared to neat polymers for long exposure time, and the addition of PP‐g‐MA increased slightly their ageing rate in accordance with TGA data. Further, DSC analysis showed an increase in the crystallinity index and a decrease in the melting temperature of PP and PA‐6 after UV exposure either as neat polymers or as blend components. SEM micrographs of the cryo‐fractured surfaces of the samples illustrated the formation of cracks and fractures after UV irradiation. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41722.     

Morphology and mechanical properties of reactive compatibilized polystyrene/ethylene‐vinyl acetate‐vinyl alcohol blends

A reactive compatibilizer, styrene‐maleic anhydride (SMA) was used to compatibilize the blends of polystyrene (PS) and ethylene‐vinyl acetate‐vinyl alcohol (EVAOH), which was synthesized from ethylene‐vinyl acetate (EVA) using transesterification reaction. The compatibilized blends with different compositions were prepared using a twin‐screw extruder and injection molded into the required test specimens. Morphology of Charpy impact‐fractured surfaces, tensile, and impact properties of the blends were investigated. Fourier‐transform infrared spectroscopy (FTIR) was also applied for specific samples to elucidate the presence of the functional groups reaction necessary for reactive compatibilization. The results of the ternary PS/EVAOH/SMA blends illustrate that the addition of SMA as a compatibilizer slightly reduce the elongation at break. From the impact‐fractured surfaces of the blends, it is evident that the morphology developed sizable pores when SMA was added into the blends. This might be attributed to the residual octanol‐1, produced from the synthesis of EVAOH, as there is a possibility of a reaction between hydroxyl groups in the octanol‐1 and the anhydride groups in the SMA. This disrupted the stability of the morphology and resulted in the decrease in the elongation, and hence, the tensile toughness. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 209–217, 2002     

Effects of reactive reinforced interface on the morphology and tensile properties of amorphous polyamide–SAN blends

The effects of reactive reinforced interface on the morphology and tensile properties of amorphous polyamide (a-PA) and styrene-acrylonitrile (SAN) copolymer blend have been investigated using styrene maleic anhydride (SMA) copolymer as a reactive compatibilizer. The anhydride groups of SMA copolymer can react with the amine groups of polyamide and form in situ graft copolymers at the a-PA–SAN interfaces during the blend preparation. The interfacial adhesion strength of the reactive reinforced interface was evaluated quantitatively using an asymmetric double cantilever beam fracture test as a function of SMA copolymer content using a model adhesive joint. The interfacial adhesion strength was found to increase with the content of SMA copolymer and then level off. The morphological observations of a-PA–SAN (80/20 w/w) blends showed that the finer dispersion of the SAN domains with rather narrow distribution was obtained by the addition of SMA copolymer into the blends. The trend of morphology change was not in accord with that of the interfacial adhesion strength with respect to the content of SMA copolymer. However, the results of tensile properties showed very similar behavior to the case of the interfacial adhesion strength with respect to SMA content; that is, there was an optimum level of the reactive compatibilizer beyond which the interfacial adhesion strength and tensile strength did not change significantly. These results clearly reveal that tensile properties of polymer blend are highly dependent on the interfacial adhesion strength. Furthermore, it is suggested that the asymmetric double cantilever beam fracture test using a model interface is a useful method to quantify the adhesion strength between the phases in real polymer blends. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68: 1925–1933, 1998     

Effects of microcompounding process parameters on the properties of ABS/polyamide‐6 blends based nanocomposites

Melt intercalation method was applied to produce acrylonitrile‐butadiene‐styrene/polyamide‐6 (ABS/PA6) blends based organoclay nanocomposites using a conical twin‐screw microcompounder. The blend was compatibilized using a maleated olefinic copolymer. The effects of microcompounding conditions such as screw speed, screw rotation‐mode (co‐ or counter‐), and material parameters such as blend composition and clay loading level on the morphology of the blends, dispersibility of nanoparticles, and mechanical properties were investigated. Furthermore, corotating screws were modified to achieve elongational flow which is efficient for obtaining dispersive mixing. The morphology was examined by SEM analysis after preferential extraction of the minor phase. Subsequently, the SEM micrographs were quantitatively analyzed using image analyzer software. The morphology of the blends indicated that processing with counter‐rotation at a given screw speed yielded coarser morphology than that of processed with corotation. X‐ray diffraction analysis showed that highest level of exfoliation is observed with increasing PA6 content, at 200 rpm of screw speed and in corotation mode. Also, the effects of screw speed, screw rotation mode, and screw modification were discussed in terms of XRD responses of the nanocomposites. The aspect ratio of the clay particles which were measured by performing image analysis on TEM micrographs exhibited a variation with processing conditions and they are in accordance with the modulus of the nanocomposites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Phase behavior and physical properties of injection‐molded polyamide 6/phenoxy blends

Polyamide 6 (PA 6)/poly(hydroxyether of bisphenol A) (phenoxy) blends were obtained by direct injection molding over the whole composition range. Differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), and scanning electron microscopy (SEM) showed the almost full immiscibility of the blends and the lack of effect of phenoxy on the crystalline phase of PA 6. The rodlike and fine‐dispersed phase of the tensile specimens was strongly deformed during tensile testing, giving characteristic fibrilar structures. The Young's modulus and yield stress showed small deviations from additivity that appeared related mainly to the blending‐induced free‐volume change. Despite immiscibility, the ductility behavior was also additive, probably due to the fibrilar morphology. However, the thicker impact specimens gave rise to less oriented larger dispersed phases and to full plane strain conditions that, in opposition to ductility, yielded impact strength values well below linearity. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 1113–1124, 1999     

Polystyrene and polyether polyurethane elastomer blends compatibilized by SMA: Morphology and mechanical properties

Blends of polystyrene (PS) and the polyether polyurethane elastomer (PU‐et) were prepared by melt mixing using poly(styrene‐co‐maleic anhydride) (SMA) containing 7 wt % of maleic anhydride as a compatibilizer. The polyurethane in the blends was crosslinked using dicumyl peroxide or sulfur. The content of maleic anhydride was varied in the blends through the addition of different SMA amounts. The morphology of the blends was analyzed by SEM and a drastic reduction of both the domain size and its distribution was observed with increase of the anhydride content in the blends. The morphology of the PU‐et blends also showed dependence on the crosslinker agent used for the elastomer, and larger domains were obtained for the elastomer phase crosslinked with dicumyl peroxide. The mechanical properties of the blends were evaluated by flexural and impact strength tests. The blend containing 0.5 wt % of maleic anhydride and 20 wt % of PU‐et crosslinked with sulfur showed the highest strength impact, which was three times superior to the PS strength impact, and the blends containing 20 wt % of PU‐et crosslinked with dicumyl peroxide showed the highest deflection at break independent of the anhydride content. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 830–837, 2002     

Comparison of carboxylated and maleated polypropylene as reactive compatibilizers in polypropylene/polyamide‐6,6 blends

Using reactive extrusion, polypropylene is functionalized with maleic anhydride and compared on an equimolar basis to polypropylene that is functionalized with an asymmetric, carboxylic acid containing peroxide. The grafting efficiency for the asymmetric peroxide is double that obtained for the maleic anhydride system. Moreover, the asymmetric peroxide yields a functionalized material with minimal molecular weight degradation and desirable mechanical properties, relative to maleic anhydride‐grafted polypropylene. In compatibilized blends of polypropylene and nylon 6,6, the polypropylene that was functionalized with the asymmetric peroxide is found to be an improved compatibilizer compared to that of maleic anhydride‐grafted polypropylene. The differences in mechanical properties of the two different functionalized polypropylene materials and their respective blends are rationalized on the basis of the grafting efficiency, molecular weight degradation during reactive extrusion, and effect of free functional species on the ability to form graft copolymers in compatibilized blends. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 79: 2398–2407, 2001     

Morphology and properties of PET/PA-6/E-44 blends

Polymer blends incorporating poly (ethylene terephthalate) (PET), polyamide-6 (PA-6), and a reactive compatibilizer (low molecular weight bisphenol-A epoxy resin—E-44) were prepared with the following E-44 weight percent concentrations: 0, 0.3, 0.6, 1, 3, 5, and 10. The samples was studied by a scanning electron microscope (SEM), a polarizing microscope (PLM), dynamic mechanical thermal analysis (DMTA), wide-angle X-ray diffraction (WAXD), a differential scanning calorimeter (DSC), infrared spectroscopy (IR), and mechanical testing. SEM and PLM showed noticeable changes in both the amorphous region and the crystalline region of the blends. The changes indicated better compatibility between the dispersed phase (PA-6) and the matrix (PET), which was further confirmed by the DMTA test. The WAXD showed that PET and PA-6 crystallized separately and no cocrystallite was found. The melting and crystallization data, obtained by DSC, suggested that the crystallization of the blend was blocked, although the hindered mechanism for the effect of E-44 on PET was different from that on PA-6. The notched impact strength and flexural strength of the PET/PA-6 blends were significantly improved when the content of E-44 was 5 wt % (improved about 500 and 400%, respectively). IR was used to study the reaction among E-44, PET, and PA-6. The result indicated that the grafting reaction and the crosslinking reaction occurred during melt blending. The obvious increase of mechanical properties and the reinforcing and toughening effect were attributed to the formation of the crosslinking net in the blend. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 1505–1515, 1998     

Effect of composition and processing conditions on the chemical and morphological evolution of PA‐6/EPM/ EPM‐g‐MA blends in a corotating twin‐screw extruder

This study investigated the effect of blend composition and processing conditions on the chemical conversion and morphological evolution of PA‐6/EPM/EPM‐g‐MA blends along a twin‐screw extruder. The maleic anhydride (MA) content of the modified rubber was found to decrease strongly, to a level of almost zero, and in the melting zone the particle size was dramatically reduced, from millimeters to submicrometers. Blend composition had a secondary effect on both chemical conversion and morphological development. The processing conditions, particularly the temperature profile and the screw speed, affected both the chemical conversion and the morphological evolution. Using low temperatures and low screw rotation it was possible to follow in detail the evolution of morphological development of a reactive blend in a twin‐screw extruder. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1535–1546, 2001     

PA 6/EPDM-g-MAH/HDPE三元共混物的形态与力学性能

制备了聚酰胺(PA)6/马来酸酐(MAH)接枝三元乙丙橡胶(EPDM)(EPDM-g-MAH)/高密度聚乙烯(HDPE)三元共混物,采用扫描电子显微镜观察了三元共混物的相形态,研究了注塑过程的二次剪切流动对该三元共混物相形态的影响,以及三元共混物相形态对其力学性能的影响。结果表明:二次剪切流动有利于PA 6/EPDM-g-MAH/HDPE体系向热力学最稳定的壳核结构发生转变。与PA 6/EPDM-g-MAH二元共混物相比,该三元共混物的力学性能得到较大改善,w(EPDM-g-MAH)为15%时,其Izod缺口冲击强度达85.83 kJ/m2,是纯PA 6的9倍,是同等橡胶含量的PA 6/EPDM-g-MAH二元共混物的2倍。     

Mechanical properties and morphology of PA6/EVA blends

The mechanical properties of blends of polyamide6 (PA6) and ethylene vinyl acetate (EVA) at a blending composition of 0–50 wt % EVA were studied. The notched Izod impact strength of PA6 increased with the incorporation of EVA, the increase being more than 100% compared to PA6 at 10% EVA. The tensile strength and the tensile modulus of the blends decreased steadily as the weight percent of EVA increased. Analysis of the tensile data using predictive theories indicated the extent of the interaction of the dispersed phase and the matrix up to 20 wt % EVA. SEM studies of the cryogenically fractured surfaces indicated increase in the dispersed phase domain size with EVA concentrations. On the other hand, impact fractured surfaces of PA6/EVA blends indicated debonding of EVA particles, leaving hemispherical bumps, indicating inadequate interfacial adhesion between PA6 and EVA. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1593–1606, 2002     

An investigation on recycled PET/PP and recycled PET/PP‐EP compatibilized blends: Rheological,morphological, and mechanical properties

The effectiveness of P(E‐co‐MA‐co‐GMA) as a compatibilizer for recycled PET/PP and recycled PET/PP‐EP (polypropylene (ethylene‐propylene) heterophase copolymer) blends was investigated by means of morphological (scanning electron microscopy), rheological (small amplitude oscillatory shear), mechanical (tensile, flexural and impact tests), and thermal (differential scanning calorimetry) properties. Compatibilizer concentration ranged from 1 to 5 wt % with respect to the whole blend. All blends were obtained in a 90/10 composition using a twin screw extruder. Compatibilization effects for PETr/PP‐EP were more pronounced due to ethylene segments present in both PP‐EP and P(E‐co‐EA‐co‐GMA). PETr/PP‐EP has shown greater dispersed phase size reduction, a more solid‐like complex viscosity behavior and larger storage modulus at low frequencies in relation to PETr/PP blend. For both investigated blends, mechanical properties indicated an improvement in both elongation at break and impact strength with increasing compatibilizer content. PETr/PP‐EP blends showed improved performance for the same level of compatibilizer content. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41892.     

Morphology and mechanical properties of ethylene‐vinyl acetate rubber/polyamide thermoplastic elastomers

High performance thermoplastic elastomers based on ethylene‐vinyl acetate rubber (EVM) and ternary polyamide copolymer (tPA) were prepared through a dynamic vulcanization process in the presence of dicumyl peroxide (DCP). The morphology, crystallization, and mechanical properties of the EVM/tPA blends were studied. A phase transition of EVM/tPA blend was observed at a weight ratio of 60/40. The presence of EVM increased the melting enthalpy at the high temperature of tPA, ascribing to the heterogeneous nucleating effect of EVM. The tensile strength of EVM/tPA (70/30) blends was increased up to 20.5 MPa as the DCP concentration increased to 3.5 phr, whereas the elongation at break of the blends kept decreasing as the DCP concentration increased. The addition of ethylene‐acrylic acid copolymer (EAA) or maleic anhydride‐grafted EVM (EVM‐g‐MAH) to the EVM/tPA blends both induced finer dispersion of the EVM particles in the tPA phase and improvement in the tensile strength and elongation at break of the blends, which were ascribed to the compatibilization of EAA or EVM‐g‐MAH. Finally, a high performance EVM/tPA (70/30) thermoplastic elastomer with Shore A hardness of 75, tensile strength of 24 MPa, elongation at break of 361%, and set at break of 20% was obtained by adding 5 wt % of EVM‐g‐MAH and 3.5 phr DCP. It has great potential in automotive and oil pipeline applications. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Compatibilization of polyethylene/polyamide 6 blends with oxazoline‐functionalized polyethylene and styrene ethylene/butylene styrene copolymer (SEBS)

Study was made of the compatibilization of polyethylene/polyamide 6 (PE/PA6) blends with a ricinoloxazoline maleinate grafted polyethylene and styrene ethylene/butylene styrene copolymer. The blends were prepared in a twin‐screw midiextruder, and the specimens for mechanical tests were injection molded with a mini‐injection molding machine. The effect of compatibilizing on the mechanical properties and the morphology of the blends was studied. The toughness and ductility of the blends were substantially improved as a result of the compatibilization. Simultaneously, the strength and stiffness were slightly reduced. Morphological studies showed that the particle size was reduced and the adhesion of the dispersed phase to the matrix was improved by the compatibilization. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 1443–1450, 1999