Adult headform impact tests of three Japanese child bicycle helmets into a vehicle

The head is the body region that most frequently incurs fatal and serious injuries of cyclists in collisions against vehicles. Many research studies investigated helmet effectiveness in preventing head injuries using accident data. In this study, the impact attenuation characteristics of three Japanese child bicycle helmets were examined experimentally in impact tests into a concrete surface and a vehicle. A pedestrian adult headform with and without a Japanese child bicycle helmet was dropped onto a concrete surface and then propelled into a vehicle at 35 km/h in various locations such as the bonnet, roof header, windshield and A-pillar. Accelerations were measured and head injury criterion (HIC) calculated. In the drop tests using the adult headform onto a concrete surface from the height of 1.5 m, the HIC for a headform without a child helmet was 6325, and was reduced by around 80% when a child helmet was fitted to the headform. In the impact tests, where the headform was fired into the vehicle at 35 km/h at various locations on a car, the computed acceleration based HIC varied depending on the vehicle impact locations. The HIC was reduced by 10–38% for impacts headforms with a child helmet when the impact was onto a bonnet-top and roof header although the HIC was already less than 1000 in impacts with the headform without a child helmet. Similarly, for impacts into the windshield (where a cyclist’s head is most frequently impacted), the HIC using the adult headform without a child helmet was 122; whereas when the adult headform was used with a child helmet, a higher HIC value of more than 850 was recorded. But again, the HIC values are below 1000. In impacts into the A-pillar, the HIC was 4816 for a headform without a child helmet and was reduced by 18–38% for a headform with a child helmet depending on the type of Japanese child helmet used. The tests demonstrated that Japanese child helmets are effective in reducing accelerations and HIC in a drop test using an adult headform onto a relatively rigid hard surface, i.e., simulating a road surface or concrete path. However, when the impact tests are into softer surfaces, the child helmet’s capacity to decrease accelerations is accordingly reduced. Impacts into the windshield, while below the critical HIC value of 1000, indicated higher HIC values for a headform with a child helmet compared to an adult headform without a child helmet. The unpredictable nature of the results indicates further research work is required to assess how representative the stiffness of an adult headform is when compared to an actual head.     

Fatigue of clamped connections with application to a stem‐handlebar assembly for off‐road bicycles

The objectives of this study were: (i) to determine the stresses as a result of assembly and the stress concentration of a clamped connection, (ii) to demonstrate the importance of the effects of assembly in fatigue life predictions and (iii) to verify the accuracy of fatigue life predictions by measuring fatigue life experimentally. A stem‐handlebar assembly used in off‐road bicycles was chosen for the study because it is a critical assembly for which structural reliability must be insured to prevent serious injury. Assembly stresses in the handlebar exceeded 200 MPa and stress concentration because of the attached stem increased the applied stress by 40%. A stress‐life prediction indicated that assembly effects would reduce predicted fatigue life of the handlebar by a factor of approximately 20. The measured fatigue lifetime of the handlebar was longer than that predicted by using the stress‐life approach, but was much shorter than that predicted when assembly effects were ignored. Therefore, assembly effects have a significant effect on fatigue life predictions and should be included in lifetime assessments for clamped mechanical assemblies.     

How similar are two-unit bicycle and motorcycle crashes?

This paper explores the similarities and differences between bicycle and motorcycle crashes with other motor vehicles. If similar treatments can be effective for both bicycle and motorcycle crashes, then greater benefits in terms of crash costs saved may be possible for the same investment in treatments. To reduce the biases associated with under-reporting of these crashes to police, property damage and minor injury crashes were excluded. The most common crash type for both bicycles (31.1%) and motorcycles (24.5%) was intersection from adjacent approaches. Drivers of other vehicles were coded most at fault in the majority of two-unit bicycle (57.0%) and motorcycle crashes (62.7%). The crash types, patterns of fault and factors affecting fault were generally similar for bicycle and motorcycle crashes. This confirms the need to combat the factors contributing to failure of other drivers to yield right of way to two-wheelers, and suggest that some of these actions should prove beneficial to the safety of both motorized and non-motorized two-wheelers. In contrast, child bicyclists were more often at fault, particularly in crashes involving a vehicle leaving the driveway or footpath. The greater reporting of violations by riders and drivers in motorcycle crashes also deserves further investigation.     

Pediatric short-distance household falls: biomechanics and associated injury severity

Objectives

Short-distance household falls are a common occurrence in young children, but are also a common false history given by caretakers to conceal abusive trauma. The purpose of this study was to determine the severity of injuries that result from accidental short-distance household falls in children, and to investigate the association of fall environment and biomechanical measures with injury outcomes.

Methods

Children aged 0–4 years who presented to the Emergency Department with a history of a short furniture fall were included in the study. Detailed case-based biomechanical assessments were performed using data collected through medical records, interviews, and fall scene investigations. Injuries were rated using the Abbreviated Injury Scale (AIS). Each case was reviewed by a child abuse expert; cases with a vague or inconsistent history and cases being actively investigated for child abuse were excluded.

Results

79 subjects were enrolled in the study; 15 had no injuries, 45 had minor (AIS 1) injuries, 17 had moderate (AIS 2) injuries, and 2 had serious (AIS 3) injuries. No subjects had injuries classified as AIS 4 or higher, and there were no fatalities. Children with moderate or serious injuries resulting from a short-distance household fall tended to have fallen from greater heights, have greater impact velocities, and have a lower body mass index than those with minor or no injuries.

Conclusion

Children aged 0–4 years involved in a short-distance household fall did not sustain severe or life-threatening injuries, and no children in this study had moderate or serious injuries to multiple body regions. Biomechanical measures were found to be associated with injury severity outcomes in short-distance household falls. Knowledge of relationships between biomechanical measures and injury outcomes can aid clinicians when assessing whether a child's injuries were the result of a short-distance fall or some other cause.     

Effect of width and boundary conditions on meeting maneuvers on two-way separated cycle tracks

Cycle track design guidelines are rarely based on scientific studies. In the case of off-road two-way cycle tracks, a minimum width must facilitate both passing and meeting maneuvers, being meeting maneuvers the most frequent. This study developed a methodology to observe meeting maneuvers using an instrumented bicycle, equipped with video cameras, a GPS tracker, laser rangefinders and speed sensors. This bicycle collected data on six two-way cycle tracks ranging 1.3–2.15 m width delimitated by different boundary conditions. The meeting maneuvers between the instrumented bicycle and every oncoming bicycle were characterized by the meeting clearance between the two bicycles, the speed of opposing bicycle and the reaction of the opposing rider: change in trajectory, stop pedaling or braking. The results showed that meeting clearance increased with the cycle track width and decreased if the cycle track had lateral obstacles, especially if they were higher than the bicycle handlebar. The speed of opposing bicycle shown the same tendency, although were more disperse. Opposing cyclists performed more reaction maneuvers on narrower cycle tracks and on cycle tracks with lateral obstacles to the handlebar height. Conclusions suggested avoiding cycle tracks narrower than 1.6 m, as they present lower meeting clearances, lower bicycle speeds and frequent reaction maneuvers.     

Methods to mitigate injury to toddlers in near-side impact crashes

This research focuses on the injury potential of children seated in forward-facing child safety seats during side impact crashes in a near-side seated position. Side impact dynamic sled tests were conducted by NHTSA at Transportation Research Center Inc. (TRC) using a Hybrid III 3-year-old child dummy seated in a convertible forward/rearward child safety seat. The seat was equipped with a LATCH and a top tether and the dummy was positioned in forward-facing/near-side configuration. The test was completed using an acceleration pulse with a closing speed of 24.1 km/h, in the presence of a rigid wall and absence of a vehicle body. A fully deformable finite element model of a child restraint seat, for side impact crash investigations, has been developed which has also been previously validated for frontal and far side impacts. A numerical model utilizing a Hybrid III 3-year-old dummy, employing a similar set-up as the experimental sled test was generated and simulated using LS DYNA. The numerical model was validated by comparing the head and the chest accelerations, resultant upper and lower neck forces and moments from the experimental and numerical tests. The simulation results were observed to be in good agreement to the experimental observations. A numerical model of the near-side laboratory tests, utilizing a Q3s child dummy, was also created for parametric studies regarding different ISOFIX configurations. Further, numerical simulations were completed for both the dummy models with rectangular and cross-shaped sections of rigid ISOFIX systems. In addition, studies were conducted to confine lateral movement of the dummy's head by adding energy absorbing foam on the side wings in the vicinity of the contact region of the CRS. It was observed that the use of rigid ISOFIX system reduced the lateral displacement of the CRS and different injury parameters. Addition of energy absorbing foam blocks was effective in further reducing the lateral displacement of the dummy's head. The lateral displacement of the head was reduced by 68 mm by using cross-shaped section ISOFIX with energy absorbing foam near the vicinity of the head of the Hybrid III 3-year-old dummy compared to the flexible LATCH configuration without foam. For the Q3s dummy, the lateral displacement of the head was reduced by 48 mm by utilizing a cross-shaped section rigid ISOFIX system with the addition of energy absorbing foam compared to the flexible LATCH configuration.     

Comparison of package cushioning materials to protect post‐harvest impact damage to apples

Damage to fruits and vegetables continues to be a big challenge as global markets become a reality. Worldwide distribution of sensitive produce is faced with various levels of impacts from shipping and handling. Despite a variety of packaging options available today, bruising damage is commonplace for post‐harvest apples throughout the supply chain. The major sources of bruising are compression, impact or vibration forces. Understanding where these forces occur can help reduce this type of mechanical damage to apples. The purpose of this study was to investigate the impact characteristics of foam net and corrugated board when applied as wrapping for individual apples. Two grades (count numbers 80 and 100) of “Fuji” cultivar apples imported to Thailand from China were studied. A simple ballistic pendulum test device was developed to measure bruise volume to impact energy relationship. A linear relationship for both types of apples was observed. Bruise volume occurrence probability and impact energy relationship fitted by linear regression were created for cushioned and bare apples. Absorbed energy of various cushioning materials was also calculated under compressive forces. Copyright © 2006 John Wiley & Sons, Ltd.     

Numerical simulation of normal and oblique ballistic impact on ceramic composite armours

This paper presents three-dimensional finite element models that investigate the performance of ceramic–composite armours when subjected to normal and oblique impacts by 7.62 AP rounds. The finite element results are compared with experimental data from different sources both for normal and oblique impact, respectively. Simulation of the penetration processes as well as the evaluation of energy and stresses distributions within the impact zones highlight the difference between normal and oblique ballistic impact phenomena. The findings show that the distributions of global kinetic, internal and total energy versus time are similar for normal and oblique impact. However, the interlaminar stresses at the ceramic–composite interface and the forces at the projectile–ceramic interface for oblique impact are found to be smaller than those for normal impact. Finally, it is observed that the projectile erosion in oblique impact is slightly greater than that in normal impact.     

Using reflective clothing to enhance the conspicuity of bicyclists at night

Bicycling at night is more dangerous than in the daytime and poor conspicuity is likely to be a contributing factor. The use of reflective markings on a pedestrian's major joints to facilitate the perception of biological motion has been shown to greatly enhance pedestrian conspicuity at night, but few corresponding data exist for bicyclists. Twelve younger and twelve older participants drove around a closed-road circuit at night and indicated when they first recognized a bicyclist who wore black clothing either alone, or together with a reflective bicycling vest, or a vest plus ankle and knee reflectors. The bicyclist pedalled in place on a bicycle that had either a static or flashing light, or no light on the handlebars. Bicyclist clothing significantly affected conspicuity; drivers responded to bicyclists wearing the vest plus ankle and knee reflectors at significantly longer distances than when the bicyclist wore the vest alone or black clothing without a vest. Older drivers responded to bicyclists less often and at shorter distances than younger drivers. The presence of a bicycle light, whether static or flashing, did not enhance the conspicuity of the bicyclist; this may result in bicyclists who use a bicycle light being overconfident of their own conspicuity at night. The implications of our findings are that ankle and knee markings are a simple and very effective approach for enhancing bicyclist conspicuity at night.     

The impact response of traditional and BMX-style bicycle helmets at different impact severities

Bicycle helmets reduce the frequency and severity of severe to fatal head and brain injuries in bicycle crashes. Our goal here was to measure the impact attenuation performance of common bicycle helmets over a range of impact speeds. We performed 127 drop tests using 13 different bicycle helmet models (6 traditional style helmets and 7 BMX-style helmets) at impact speeds ranging from 1 to 10 m/s onto a flat anvil. Helmets were struck on their left front and/or right front areas, a common impact location that was at or just below the test line of most bicycle helmet standards. All but one of the 10 certified helmet models remained below the 300 g level at an impact speed of 6 m/s, whereas none of the 3 uncertified helmets met this criterion. We found that the helmets with expanded polystyrene liners performed similarly and universally well. The single certified helmet with a polyurethane liner performed below the level expected by the Consumer Product Safety Commission (CPSC) standard at our impact location and the helmet structure failed during one of two supplemental tests of this helmet above the test line. Overall, we found that increased liner thickness generally reduced peak headform acceleration, particularly at higher impact speeds.     

Commuting by bike in Belgium, the costs of minor accidents

Minor bicycle accidents are defined as “bicycle accidents not involving death or heavily injured persons, implying that possible hospital visits last less than 24 hours”. Statistics about these accidents and related injuries are very poor, because they are mostly not reported to police, hospitals or insurance companies. Yet, they form a major share of all bicycle accidents. Official registrations underestimate the number of minor accidents and do not provide cost data, nor the distance cycled. Therefore related policies are hampered by a lack of accurate data.This paper provides more insight into the importance of minor bicycle accidents and reports the frequency, risk and resulting costs of minor bicycle accidents. Direct costs, including the damage to bike and clothes as well as medical costs and indirect costs such as productivity loss and leisure time lost are calculated. We also estimate intangible costs of pain and psychological suffering and costs for other parties involved in the accident. Data were collected during the SHAPES project using several electronic surveys. The weekly prospective registration that lasted a year, covered 1187 persons that cycled 1,474,978 km. 219 minor bicycle accidents were reported. Resulting in a frequency of 148 minor bicycle accidents per million kilometres. We analyzed the economic costs related to 118 minor bicycle accidents in detail. The average total cost of these accidents is estimated at 841 euro (95% CI: 579–1205) per accident or 0.125 euro per kilometre cycled. Overall, productivity loss is the most important component accounting for 48% of the total cost. Intangible costs, which in past research were mostly neglected, are an important burden related to minor bicycle accidents (27% of the total cost). Even among minor accidents there are important differences in the total cost depending on the severity of the injury.     

Characteristics of bicycle crashes in an adolescent population in Flanders (Belgium)

IntroductionIn regions where transportation is mainly motorized, air pollution and traffic congestion are rife. Active transportation such as cycling might be a solution but safety is a major concern. An efficient science based safety policy is needed. The aim of this paper is to analyze in depth the bicycle crash causes and characteristics in an adolescent population (14–18 yr).MethodsBy using questionnaires for self-reported bicycle crashes, bicycle crash data were collected from insurance companies (January 2014–June 2015) and from schools (November 2013–March 2014). Six bicycle crash causes were predefined and possible differences between schools and insurance companies were analyzed.ResultsEighty-six school and 78 insurance registered crashes were analyzed. “Distraction of the cyclist” and “third party crossing a bicycle path failing to see the cyclist” are the main causes of bicycle crashes (both 29%). Bad (maintained) infrastructure accounted for 21% of the crash causes. Bicycle crashes reported at insurance companies needed significantly more medical attention and led to high absenteeism (57% at least one day of absenteeism). Only 21% of the bicycle crashes reported at insurance companies were also reported in the official police database.ConclusionThe human factor was the main cause accounting for 79% of the crashes. Bicycle crashes involving a car accounted for 42% and single bicycle crashes accounted for 31% of the total number of crashes. From the bicycle crashes registered at insurance companies 21% was also registered in official police statistics. A combination of information, education and changing the bicycle specific environment might reduce the consequences of human errors more efficiently.     

Child pedestrian safety: Parental supervision, modeling behaviors, and beliefs about child pedestrian competence

Pedestrian injuries are a significant health risk to children, particularly those 5–9 years of age. Surprisingly, few studies have explored parent-related factors that may moderate this risk. The present study used naturalistic observations of parent–child pairs crossing at uncontrolled intersections and a short interview to examine parental supervision of children during crossings, modeling of safe-crossing behaviors, beliefs about how children come to cross streets safely, and whether child attributes (age, sex) relate to parental practices and beliefs. Results revealed that parents more closely supervised younger than older children, they modeled safer crossing practices for sons more than daughters, particularly younger sons, and although over half the sample believed children need to be explicitly taught how to cross safely, few actually provided any instruction when crossing with their children. Providing parents both with guidelines for how to accurately appraise their child's readiness for crossing independently and with information about best practices for teaching children how to cross safely may facilitate parents’ implementing these practices, particularly if this is coupled with public advocacy highlighting the important role they could play to reduce the risk of child pedestrian injury.     

Bicyclists overestimate their own night-time conspicuity and underestimate the benefits of retroreflective markers on the moveable joints

Conspicuity limitations make bicycling at night dangerous. This experiment quantified bicyclists’ estimates of the distance at which approaching drivers would first recognize them. Twenty five participants (including 13 bicyclists who rode at least once per week, and 12 who rode once per month or less) cycled in place on a closed-road circuit at night-time and indicated when they were confident that an approaching driver would first recognize that a bicyclist was present. Participants wore black clothing alone or together with a fluorescent bicycling vest, a fluorescent bicycling vest with additional retroreflective tape, or the fluorescent retroreflective vest plus ankle and knee reflectors in a modified ‘biomotion’ configuration. The bicycle had a light mounted on the handlebars which was either static, flashing or off. Participants judged that black clothing made them least visible, retroreflective strips on the legs in addition to a retroreflective vest made them most visible and that adding retroreflective materials to a fluorescent vest provides no conspicuity benefits. Flashing bicycle lights were associated with higher conspicuity than static lights. Additionally, occasional bicyclists judged themselves to be more visible than did frequent bicyclists. Overall, bicyclists overestimated their conspicuity compared to previously collected recognition distances and underestimated the conspicuity benefits of retroreflective markings on their ankles and knees. Participants mistakenly judged that a fluorescent vest that did not include retroreflective material would enhance their night-time conspicuity. These findings suggest that bicyclists have dangerous misconceptions concerning the magnitude of the night-time conspicuity problem and the potential value of conspicuity treatments.     

Axial cutting of AA6061-T6 circular extrusions under impact using single- and dual-cutter configurations

Experimental and numerical axial cutting of AA6061-T6 circular extrusions under both dynamic and quasi-static loading conditions were completed using single- and dual-cutter configurations to investigate load/displacement and collapse behaviour of the extrusions. Circular specimens with various wall thicknesses were considered for impact and quasi-static testing in this research. A steel cutter (AISI 4140) with four blades, having blade tip widths of 1.0 mm or 0.75 mm and blade lengths of 7 mm or 26.1 mm were used to cut through the extrusions. Straight and curved deflector profiles were used to flare the cut petalled sidewalls and facilitate the cutting system. Further quasi-static cutting tests using dual cutters were completed with or without the presence of a spacer to examine the load/displacement response as an adaptive energy absorption system. Results from the experimental impact tests illustrated that a higher peak cutting force, with a magnitude of approximately 1.09–1.98 times that of the force necessary under quasi-static testing conditions, was needed to initiate the cutting deformation mode. After this initial high force, the load/displacement responses were observed to be similar to those from the quasi-static tests with the exception of minor variations which resulted from material fracture that occurred on the petalled sidewalls during dynamic testing. Larger lengths of cutter blades and the curved deflector eased the flaring of the petalled sidewalls and reduced the occurrence of material fracture. The blade tip width had minor effects on the initial peak cutting force and mean cutting forces for extrusions under impact loading. The mean cutting force from the dynamic tests was determined to be 0.82–1.2 times that from the quasi-static experimental tests. Finally, quasi-static axial crushing of extrusions was completed to compare crashworthiness measures with the adaptive energy absorption system under the cutting deformation mode. A finite element model incorporating an Eulerian formulation was selected for the numerical model to simulate the cutting process. Simulation results generally agreed well with the experimental tests with a maximum over prediction of approximately 33% and 18% for the cutting force under impact and quasi-static loading, respectively.     

Trends in helmet use and head injuries in San Diego County: the effect of bicycle helmet legislation

The purpose of this study is to evaluate the effect of California's bicycle helmet law on bicycle-related head injuries in San Diego County with a year 2000 population of approximately 3 million people. The study design is an ecological trend design based on observational data from a Trauma Registry. Outcome measures include helmet use compliance, site/severity of injury and abbreviated injury scale (AIS). There were 1116 bicycle trauma patients recorded in the San Diego County Trauma Registry between 1992 and 1996. The percentages of pre-law and post-law helmet use were 13.2 and 31.7%, respectively. Over the whole study period, the overall helmet use increased by an average of 43% per year with an averaged 84% rate increase in helmet use among children. Only 16.1% of patients with serious head injury used helmets, compared to 28.2% in those who did not have serious head injury. The odds ratio of helmet use against serious head injuries is 0.43 (95% CI 0.28-0.66) after adjusting for age, ethnicity and time. The p-values for comparing pre- and post-legislation serious head injury rates are p=0.764, 0.4 and 0.194 for the overall, adult and child populations, respectively. Helmet legislation increased helmet use in the targeted child population and the effect was carried over to the adult population. Helmet use has a protective effect against serious head injury. Probably due to several of its limitations, the current study did not confirm that helmet legislation alone significantly reduced head injury rates in San Diego County during the study period.     

Bicycle helmets are highly effective at preventing head injury during head impact: Head-form accelerations and injury criteria for helmeted and unhelmeted impacts

Cycling is a popular form of recreation and method of commuting with clear health benefits. However, cycling is not without risk. In Canada, cycling injuries are more common than in any other summer sport; and according to the US National Highway and Traffic Safety Administration, 52,000 cyclists were injured in the US in 2010. Head injuries account for approximately two-thirds of hospital admissions and three-quarters of fatal injuries among injured cyclists. In many jurisdictions and across all age levels, helmets have been adopted to mitigate risk of serious head injuries among cyclists and the majority of epidemiological literature suggests that helmets effectively reduce risk of injury. Critics have raised questions over the actual efficacy of helmets by pointing to weaknesses in existing helmet epidemiology including selection bias and lack of appropriate control for the type of impact sustained by the cyclist and the severity of the head impact. These criticisms demonstrate the difficulty in conducting epidemiology studies that will be regarded as definitive and the need for complementary biomechanical studies where confounding factors can be adequately controlled. In the bicycle helmet context, there is a paucity of biomechanical data comparing helmeted to unhelmeted head impacts and, to our knowledge, there is no data of this type available with contemporary helmets. In this research, our objective was to perform biomechanical testing of paired helmeted and unhelmeted head impacts using a validated anthropomorphic test headform and a range of drop heights between 0.5 m and 3.0 m, while measuring headform acceleration and Head Injury Criterion (HIC). In the 2 m (6.3 m/s) drops, the middle of our drop height range, the helmet reduced peak accelerations from 824 g (unhelmeted) to 181 g (helmeted) and HIC was reduced from 9667 (unhelmeted) to 1250 (helmeted). At realistic impact speeds of 5.4 m/s (1.5 m drop) and 6.3 m/s (2.0 m drop), bicycle helmets changed the probability of severe brain injury from extremely likely (99.9% risk at both 5.4 and 6.3 m/s) to unlikely (9.3% and 30.6% risk at 1.5 m and 2.0 m drops respectively). These biomechanical results for acceleration and HIC, and the corresponding results for reduced risk of severe brain injury show that contemporary bicycle helmets are highly effective at reducing head injury metrics and the risk for severe brain injury in head impacts characteristic of bicycle crashes.     

Macroscopic modeling of pedestrian and bicycle crashes: A cross-comparison of estimation methods

The paper presents a cross-comparison of different estimation methods to model pedestrian and bicycle crashes. The study contributes to macro level safety studies by providing further methodological and empirical evidence on the various factors that influence the frequency of pedestrian and bicycle crashes at the planning level. Random parameter negative binomial (RPNB) models are estimated to explore the effects of various planning factors associated with total, serious injury and minor injury crashes while accounting for unobserved heterogeneity. Results of the RPNB models were compared with the results of a non-spatial negative binomial (NB) model and a Poisson-Gamma-CAR model. Key findings are, (1) the RPNB model performed best with the lowest mean absolute deviation, mean squared predicted error and Akaiki information criterion measures and (2) signs of estimated parameters are consistent if these variables are significant in models with the same response variables. We found that vehicle kilometers traveled (VKT), population, percentage of commuters cycling or walking to work, and percentage of households without motor vehicles have a significant and positive correlation with the number of pedestrian and bicycle crashes. Mixed land use is also found to have a positive association with the number of pedestrian and bicycle crashes. Results have planning and policy implications aimed at encouraging the use of sustainable modes of transportation while ensuring the safety of pedestrians and cyclist.     

Effect of impact interaction in a discharge regulation on timing precision

Conclusions The impact stage in the discharge-regulator mechanism can be interpreted as a single instantaneous absolutely nonelastic impact and a subsequent kinematically coupled movement of the balancer and escapement wheel in the absence of friction losses.In order to reduce the effect of the collision instability conditions on the timing precision it is necessary, in addition to structural stabilization of the impact conditions, also to reduce friction losses in the discharge regulator mechanism.As a result of adopting structural stabilization measures and reducing friction losses in discharge regulators without natural oscillation frequencies, it is possible to reduce the timing error contributed by the collision instability conditions from 1–1.5% to 0.2–0.3%, thus serving to reduce the total timing error to 1%.The impact instability conditions in the discharge-regulator mechanism affect the energy balance not with respect to the total energy-loss variations due to impacts, but with respect to friction-loss variations.Translated from Izmeritel'naya Tekhnika, No. 2, pp. 37–39, February, 1979.