Influence of preparation method on performance of Cu(Zn)(Zr)-alumina catalysts for the hydrogen production via steam reforming of methanol

The selective production of hydrogen via steam reforming of methanol (SRM) was performed using prepared catalysts at atmospheric pressure over a temperature range 200–260^∘C. Reverse water gas shift reaction and methanol decomposition reactions also take place simultaneously with the steam reforming reaction producing carbon monoxide which is highly poisonous to the platinum anode of PEM fuel cell, therefore the detailed study of effect of catalyst preparation method and of different promoters on SRM has been carried out for the minimization of carbon monoxide formation and maximization of hydrogen production. Wet impregnation and co-precipitation methods have been comparatively examined for the preparation of precursors to Cu(Zn)(Al₂O₃) and Cu(Zn)(Zr)(Al₂O₃). The catalyst preparation method affected the methanol conversion, hydrogen yield and carbon monoxide formation significantly. Incorporation of zirconia in Cu(Zn)(Al₂O₃) catalyst enhanced the catalytic activity, hydrogen selectivity and also lower the CO formation. Catalyst Cu(Zn)(Zr)(Al₂O₃) with composition Cu/Zn/Zr/Al:12/4/4/80 prepared by co-precipitation method was the most active catalyst giving methanol conversion up to 97% and CO concentration up to 400 ppm. Catalysts were characterized by atomic absorption spectroscopy (AAS), Brunauer-Emett-Teller (BET) surface area, pore volume, pore size and X-ray powder diffraction (XRPD). The XRPD patterns revealed that the addition of zirconia improves the dispersion of copper which resulted in the better catalytic performance of Cu(Zn)(Zr)(Al₂O₃). The time-on-stream (TOS) catalysts stability test was also conducted for which the Cu(Zn)(Zr)(Al₂O₃) catalyst gave the consistent performance for a long time compared to other catalysts.     

Synergistic Catalysis of Carbon Dioxide Hydrogenation into Methanol by Yttria-Doped Ceria/γ-Alumina-Supported Copper Oxide Catalysts: Effect of Support and Dopant

Methanol synthesis from carbon dioxide hydrogenation was studied over ceria/-alumina- and yttria-doped ceria (YDC)/-alumina-supported copper oxide catalysts to seek insight into the catalysis at metal–support interfaces. It was found that, in comparison with Cu/-Al₂O₃, the Cu/CeO₂/-Al₂O₃ and Cu/YDC/-Al₂O₃ catalysts exhibited substantial enhancement in activity and selectivity toward methanol formation. The extent of enhancement was augmented by increased ceria loading on -alumina and with increased yttria doping into ceria. The enhancement is inferred to result from the synergistic effect between copper oxide and surface oxygen vacancies of ceria.     

CO2 Hydrogenation to Methanol Over Cu/ZnO/Al2O3 Catalysts Prepared by a Novel Gel-Network-Coprecipitation Method

A novel gel-network-coprecipitation process has been developed to prepare ultrafine Cu/ZnO/Al₂O₃ catalysts for methanol synthesis from CO₂ hydrogenation. It is demonstrated that the gel-network-coprecipitation method can allow the preparation of the ultrafine Cu/ZnO/Al₂O₃ catalysts by homogeneous coprecipitation of the metal nitrate salts in the gel network formed by gelatin solution, which makes the metallic copper in the reduced catalyst exist in much smaller crystallite size and exhibit a much higher metallic copper-specific surface area. The effect of the gel concentration of gelatin on the structure, morphology and catalytic properties of the Cu/ZnO/Al₂O₃ catalysts for methanol synthesis from hydrogenation of carbon dioxide was investigated. The Cu/ZnO/Al₂O₃ catalysts prepared by the gel-network-coprecipitation method exhibit a high catalytic activity and selectivity in CO₂ hydrogenation to methanol.     

Synergetic effect of combined use of Cu–ZnO–Al2O3 and Pt–Al2O3 for the steam reforming of methanol

Commercial Cu–ZnO–Al₂O₃ catalysts are used widely for steam reforming of methanol. However, the reforming reactions should be modified to avoid fuel cell catalyst poisoning originated from carbon monoxide. The modification was implemented by mixing the Cu–ZnO–Al₂O₃ catalyst with Pt–Al₂O₃ catalyst. The Pt–Al₂O₃ and Cu–ZnO–Al₂O₃ catalyst mixture created a synergetic effect because the methanol decomposition and the water–gas shift reactions occurred simultaneously over nearby Pt–Al₂O₃ and Cu–ZnO–Al₂O₃ catalysts in the mixture. A methanol conversion of 96.4% was obtained and carbon monoxide was not detected from the reforming reaction when the Pt–Al₂O₃ and Cu–ZnO–Al₂O₃ catalyst mixture was used.     

Role of La2O3 in Pd-Supported Catalysts for Methanol Decomposition

Systems of Pd supported on various La₂O₃-modified -Al₂O₃ and CeO₂–Al₂O₃ catalysts were tested for catalytic methanol decomposition and characterized by means of XRD, BET, TPR, H₂-chemisorption and CO–FTIR. The addition of lanthanum significantly improved the selectivity of CO and H₂ for all the catalysts but showed a different influence on the catalytic activity in two systems. Methanol conversion decreased on La₂O₃-modified Pd/-Al₂O₃ catalysts, in line with the reduction of Pd dispersion, while the addition of La₂O₃ improved the dispersion of Pd and reinforced Pd–CeO₂ interaction for La₂O₃-modified Pd/CeO₂–Al₂O₃ catalysts, which resulted in a high production rate of CO and H₂. Thus, a synergistic effect between CeO₂ and La₂O₃ was observed on -Al₂O₃-supported Pd catalyst for methanol decomposition.     

Stable carbon dioxide reforming of methane over modified Ni/Al2O3 catalysts

CO₂ reforming of methane was studied over modified Ni/Al₂O₃ catalysts. The metal modifiers were Co, Cu, Zr, Mn, Mo, Ti, Ag and Sn. Relative to unmodified Ni/Al₂O₃, catalysts modified with Co, Cu and Zr showed slightly improved activity, while other promoters reduced the activity of CO₂ reforming. Mn-promoted catalyst showed a remarkable reduction in coke deposition, while entailing only a small reduction in catalytic activity compared to unmodified catalyst. The catalysts prepared at high calcination temperatures showed higher activity than those prepared at low calcination temperature. The Mn-promoted catalyst showed very low coke deposition even in the absence of diluent gas and the activity changed only slightly during 100 h operation. This revised version was published online in July 2006 with corrections to the Cover Date.     

Investigating the effect of metal oxide additives on the properties of Cu/ZnO/Al2O3 catalysts in methanol synthesis from syngas using factorial experimental design

The Cu/ZnO/Al₂O₃ catalysts, prepared by co-precipitation method, have been modified by adding small amount of Mn, Mg, Zr, Cr, Ba, W and Ce oxides using design of experiments (1/16 full factorial design). The structure and morphology of catalysts were studied by X-ray diffraction (XRD) and BET. Performance of the prepared catalysts for CO/CO₂ hydrogenation to methanol was evaluated by using a stainless steel fixed-bed reactor at 5 MPa and 513 K. The oxide additives were found to influence the catalytic activity, dispersion of Cu, Cu crystallite size, surface composition of catalyst and stability of catalysts during their operations. The results showed that the Mn and Zr promoted catalysts have high performance for methanol synthesis from syngas.     

A highly efficient Cu/ZnO/Al2O3 catalyst via gel-coprecipitation of oxalate precursors for low-temperature steam reforming of methanol

The impact of preparation methods on the structure and catalytic behavior of Cu/ZnO/Al₂O₃ catalysts for H₂ production from steam reforming of methanol (SRM) has been reported. The results show that the nanostructured Cu/ZnO/Al₂O₃ catalyst obtained by a novel gel-coprecipitation of oxalate precursors has a high specific surface area and high component dispersion, exhibiting much higher activity in the SRM reaction as compared to the catalysts prepared by conventional coprecipitation techniques. It is suggested that the superior catalytic performance of the oxalate gel-coprecipitation-derived Cu/ZnO/Al₂O₃ catalyst could be attributed to the generation of “catalytically active” copper material with a much higher metallic copper specific surface as well as a stronger Cu–Zn interaction due to an easier incorporation of zinc species into CuC₂O₄ · x H₂O precursors as a consequence of isomorphous substitution between copper and zinc in the oxalate gel-precursors.     

Hydrogen production by oxidative steam reforming of methanol using ceria promoted copper–alumina catalysts

The performance of different Cu/CeO₂/Al₂O₃ catalysts of varying compositions is investigated for the oxidative steam reforming of methanol (OSRM) in order to produce the hydrogen selectively for polymer electrolyte membrane (PEM) fuel cell applications. All the catalysts were prepared by co-precipitation method and characterized for their surface area, pore volume and oxidation–reduction behavior. The effect of various operating parameters studied are as follows: reaction temperature (200–300 °C), contact-time (W/F = 3–15 kg_cat s mol^− 1) and oxygen to methanol (O/M) molar ratio (0–0.5). The steam to methanol (S/M) molar ratio = 1.5 and pressure = 1 atm were kept constant. Among all the catalysts studied, catalyst Cu–Ce–Al:30–20–50 exhibited 100% methanol conversion and 179 mmol s^− 1 kg_cat^− 1 hydrogen production rate at 280 °C with carbon monoxide formation as low as 0.19%. The high catalytic activity and hydrogen selectivity shown by ceria promoted Cu/Al₂O₃ catalysts is attributed to the improved specific surface area, dispersion and reducibility of copper which were confirmed by characterizing the catalysts through temperature programmed reduction (TPR), CO chemisorption, X-ray diffraction (XRD) and N₂ adsorption–desorption studies. Reaction parameters were optimized in order to produce hydrogen with carbon monoxide formation as low as possible. The time-on-stream stability test showed that the Cu/CeO₂/Al₂O₃ catalysts were quite stable.     

Investigation of CH4 Reforming with CO2 on Meso-Porous Al2O3-Supported Ni Catalyst

Meso-porous Al₂O₃-supported Ni catalysts exhibited the highest activity, stability and excellent coke-resistance ability for CH₄ reforming with CO₂ among several oxide-supported Ni catalysts (meso-porous Al₂O₃ (Yas1-2, Yas3-8), -Al₂O₃, -Al₂O₃, SiO₂, MgO, La₂O₃, CeO₂ and ZrO₂). The properties of deposited carbons depended on the properties of the supports, and on the meso-porous Al₂O₃-supported Ni catalyst, only the intermediate carbon of the reforming reaction formed. XRD and H₂-TPR analysis found that mainly spinel NiAl₂O₄ formed in meso-porous Al₂O₃ and -Al₂O₃-supported catalysts, while only NiO was detected in -Al₂O₃, SiO₂, CeO₂, La₂O₃ and ZrO₂ supports. The strong interaction between Ni and meso-porous Al₂O₃ improved the dispersion of Ni, retarded its sintering and improved the activated adsorption of CO₂. The coking reaction via CH₄ temperature-programed decomposition indicated that meso-porous Al₂O₃-supported Ni catalysts were less active for carbon formation by CH₄ decomposition than Ni/-Al₂O₃ and Ni/-Al₂O₃.     

Low-temperature methanol synthesis catalyzed over Cu/γ-Al2O3–TiO2 for CO2 hydrogenation

A titanium-modified -alumina-supported CuO catalyst has been prepared and used for methanol synthesis from CO₂ hydrogenation. XRD and TPR were used to characterize the phase, reduction property and particle size of the reduced catalyst. The addition of Ti to the CuO/-Al₂O₃ catalyst made the copper in the catalyst exist in much smaller crystallites and exhibit an amorphous-like structure. The adding of Ti made the reduction peak shift toward lower temperature in comparison with the CuO/-Al₂O₃ catalyst. The effect of the addition of Ti and the reaction conditions on the activity and selectivity to methanol from CO₂ hydrogenation were investigated. The activity was found to increase with increasing surface area of metallic copper, but it is not a linear relationship. This indicated that the catalytic activity of the catalysts depends on both the metallic copper area and the synergy between the copper and titanium dioxide. The effect of contact time on the relative selectivity (=SCH₃0H /S_CO) and selectivity of methanol were also investigated. The results indicated that methanol was formed directly from the hydrogenation of CO₂.     

Partial Oxidation Reforming Catalyst for Fuel Cell-Powered Vehicles Applications

Transition metal oxide formulations for the partial oxidation (POX) reforming of isooctane were investigated for an onboard gasoline fuel processor. Ni/M/MgO/Al₂O₃ systems are more active than a commercial ICI catalyst. These catalysts showed better sulfur tolerance over the commercial ICI catalyst in the POX reforming of isooctane containing sulfur (Cs = 100 ppm). There was no apparent deactivation or modification of structure during 770h onstream. It was found that Ni/(Fe,Co)/MgO/Al₂O₃ catalyst is a promising candidate as POX reforming catalyst for gasoline fuel processor applications.     

Deactivation of Supported Copper Catalysts for Methanol Synthesis

Binary Cu/ZnO and Cu/Al₂O₃ as well as ternary Cu/ZnO/Al₂O₃ catalysts were investigated with respect to their catalytic activity and stability in methanol synthesis. In a rapid aging test, activity measurements were carried out in combination with the determination of the specific Cu surface area. A close correlation between the loss of catalytic activity and the decrease in specific Cu surface area was found due to sintering of the Cu particles. Differences in the deactivation behavior and the area-activity relationship of each catalyst system imply that the catalysts should be grouped in different classes.     

Activation mechanism of methane-derived coke (CHx) by CO2 during dry reforming of methane – comparison for Pt/Al2O3 and Pt/ZrO2

The reaction of methane-derived coke (CH_x: intermediate of the reforming reaction and also a source of coke deposition) with CO₂ was studied on supported Pt catalysts in relation with CO₂ reforming of methane. Temperature-programmed hydrogenation (TPH) was performed to investigate the reactivity of coke deposition after the catalyst was exposed to CH₄/He at 1070 K. Coke on Pt/Al₂O₃ could be hydrogenated around 873 K, while for Pt/ZrO₂ this was above 1073 K. The results indicate that the reactivity of coke with hydrogen was higher on Pt/Al₂O₃ than on Pt/ZrO₂, which was different from the reactivity of coke towards CO₂. Thus, the reactivity of CO₂ was studied and compared on these catalysts by several technics. The amount of CO evolution was measured during CO₂ flow at 1070 and 875 K. Rate and amount of converted CO₂ were higher on Pt/ZrO₂ than on Pt/Al₂O₃. Pt/ZrO₂ was proven to react with CO₂ to produce CO and active oxygen (CO₂CO+O) (probably on its oxygen defect site) more easily than Pt/Al₂O₃.     

Steam reforming of LPG over Ni and Rh supported on Gd-CeO2 and Al2O3: Effect of support and feed composition

The steam reforming of liquefied petroleum gas (LPG) over Ni- and Rh-based catalysts supported on Gd-CeO₂ (CGO) and Al₂O₃ was studied at 750-900 °C. The order of activity was found to be Rh/CGO > Ni/CGO ∼ Rh/Al₂O₃ > Ni/Al₂O₃; we indicated that the comparable activity of Ni/CGO to precious metal Rh/Al₂O₃ is due to the occurring of gas-solid reactions between hydrocarbons and lattice oxygen () on CGO surface along with the reaction taking place on the active site of Ni, which helps preventing the carbon deposition and promoting the steam reforming of LPG.The effects of O₂ (as oxidative steam reforming) and H₂ adding were further studied over Ni/CGO and Ni/Al₂O₃. It was found that the additional of these compounds significantly reduced the amount of carbon deposition and promoted the conversion of hydrocarbons (i.e., LPG as well as CH₄, C₂H₄ and C₂H₆ occurred from the thermal decomposition of LPG) to CO and H₂. Nevertheless, the addition of too high O₂ oppositely decreased H₂ yield due to the oxidizing of Ni particle and the possible combusting of H₂ generated from the reaction, while the addition of too high H₂ also negatively affect the catalyst activity due to the occurring of catalyst active site competition and the inhibition of gas-solid reactions between the gaseous hydrocarbon compounds and on the surface of CGO (for the case of Ni/CGO).     

An EXAFS study of Cu/ZnO and Cu/ZnO-Al2O3 methanol synthesis catalysts

Cu K-absorption edge and EXAFS measurements on binary Cu/ZnO and ternary Cu/ ZnO-Al₂O₃ catalysts of varying compositions on reduction with hydrogen at 523 K, show the presence of Cu microclusters and a species of Cu¹⁺ dissolved in ZnO apart from metallic Cu and Cu₂O. The proportions of different phases critically depend on the heating rate especially for catalysts of higher Cu content. Accordingly, hydrogen reduction with a heating rate of 10 K/min predominantly yields the metal species (>50%), while a slower heating rate of 0.8 K/min enhances the proportion of the Cu¹⁺ species ( 60%). Reduced Cu/ZnO-Al₂O₃ catalysts show the presence of metallic Cu (upto 20%) mostly in the form of microclusters and Cu¹⁺ in ZnO as the major phase ( 60%). The addition of alumina to the Cu/ZnO catalyst seems to favour the formation of Cu¹⁺/ZnO species.     

Activity and stability of Cu/ZnO/Al2O3 catalyst promoted with B2O3 for methanol synthesis

The addition of B₂O₃ to a Cu/ZnO/Al₂O₃ catalyst increased the activity of the catalyst for methanol synthesis after an induction period during the reaction. The stability of the B₂O₃-containing Cu/ZnO/Al₂O₃ catalyst was greatly improved by the addition of a small amount of colloidal silica to the catalyst. This revised version was published online in July 2006 with corrections to the Cover Date.     

A quantum-chemical study of adsorbed nonclassical carbonium ions as active intermediates in catalytic transformations of paraffins. I. Protolytic cracking of ethane on high silica zeolites

Coprecipitated Cu-ZrO₂ catalysts were found to show higher selectivity to methanol in CO₂ hydrogenation than conventional Cu-ZnO catalysts. Addition of ZnO to Cu-ZrO₂ catalysts of Cu/ZrO₂ = 1 (weight ratio) greatly enhanced the activity at lower temperatures, while keeping the high methanol selectivity of Cu-ZrO₂ catalysts. A remarkable increase in the Cu dispersion with increased amount of added ZnO explains the increased activity at lower temperatures, while the reforming of methanol to CO is accelerated by ZnO at higher temperatures, leading to a lowered yield of methanol. It is suggested that ZrO₂ rather than ZnO in the ternary systems plays a more effective role for the selective formation of methanol.     

Influence of preparation method on performance of Cu(Zn)(Zr)-alumina catalysts for the hydrogen production via steam reforming of methanol

The selective production of hydrogen via steam reforming of methanol (SRM) was performed using prepared catalysts at atmospheric pressure over a temperature range 200–260^°C. Reverse water gas shift reaction and methanol decomposition reactions also take place simultaneously with the steam reforming reaction producing carbon monoxide which is highly poisonous to the platinum anode of PEM fuel cell, therefore the detailed study of effect of catalyst preparation method and of different promoters on SRM has been carried out for the minimization of carbon monoxide formation and maximization of hydrogen production. Wet impregnation and co-precipitation methods have been comparatively examined for the preparation of precursors to Cu(Zn)(Al₂O₃) and Cu(Zn)(Zr)(Al₂O₃). The catalyst preparation method affected the methanol conversion, hydrogen yield and carbon monoxide formation significantly. Incorporation of zirconia in Cu(Zn)(Al₂O₃) catalyst enhanced the catalytic activity, hydrogen selectivity and also lower the CO formation. Catalyst Cu(Zn)(Zr)(Al₂O₃) with composition Cu/Zn/Zr/Al:12/4/4/80 prepared by co-precipitation method was the most active catalyst giving methanol conversion up to 97% and CO concentration up to 400 ppm. Catalysts were characterized by atomic absorption spectroscopy (AAS), Brunauer-Emett-Teller (BET) surface area, pore volume, pore size and X-ray powder diffraction (XRPD). The XRPD patterns revealed that the addition of zirconia improves the dispersion of copper which resulted in the better catalytic performance of Cu(Zn)(Zr)(Al₂O₃). The time-on-stream (TOS) catalysts stability test was also conducted for which the Cu(Zn)(Zr)(Al₂O₃) catalyst gave the consistent performance for a long time compared to other catalysts.     

Lean NOx catalysis over alumina‐supported catalysts

aluminasupported catalysts show promise as lean NO_x catalysts. The role of alumina in influencing the structural and chemical properties of the active phase supported on it is discussed using some effective aluminabased lean NO_x catalysts. These include Ag/Al₂O₃, CoO_x/Al₂O₃ and SnO₂/Al₂O₃. Alumina plays an important role in stabilizing Ag in the oxidic phase and cobalt in the 2+ oxidation state. For SnO₂/Al₂O₃, alumina increases the SnO₂ surface area. On both Ag/Al₂O₃ and SnO₂/Al₂O₃, alumina also participates actively in the NO_x reduction reaction. An active organic intermediate is formed on Ag or Sn oxide which reacts with NO_x subsequently on alumina to form N₂.