首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 31 毫秒
1.
In this study, an adaptive fuzzy prescribed performance control approach is developed for a class of uncertain multi-input and multi-output (MIMO) nonlinear systems with unknown control direction and unknown dead-zone inputs. The properties of symmetric matrix are exploited to design adaptive fuzzy prescribed performance controller, and a Nussbaum-type function is incorporated in the controller to estimate the unknown control direction. This method has two prominent advantages: it does not require the priori knowledge of control direction and only three parameters need to be updated on-line for this MIMO systems. It is proved that all the signals in the resulting closed-loop system are bounded and that the tracking errors converge to a small residual set with the prescribed performance bounds. The effectiveness of the proposed approach is validated by simulation results.  相似文献   

2.
In this paper, an active fuzzy fault tolerant tracking control (AFFTTC) scheme is developed for a class of multi-input multi-output (MIMO) unknown nonlinear systems in the presence of unknown actuator faults, sensor failures and external disturbance. The developed control scheme deals with four kinds of faults for both sensors and actuators. The bias, drift, and loss of accuracy additive faults are considered along with the loss of effectiveness multiplicative fault. A fuzzy adaptive controller based on back-stepping design is developed to deal with actuator failures and unknown system dynamics. However, an additional robust control term is added to deal with sensor faults, approximation errors, and external disturbances. Lyapunov theory is used to prove the stability of the closed loop system. Numerical simulations on a quadrotor are presented to show the effectiveness of the proposed approach.  相似文献   

3.
In this paper an adaptive neural network (NN)-based nonlinear controller is proposed for trajectory tracking of uncertain nonlinear systems. The adopted control algorithm combines a continuous second-order sliding mode control (CSOSMC), the radial basis function neural network (RBFNN) and the adaptive control methodology. First, a second-order sliding mode control scheme (SOSMC), which is published recently in literature for linear uncertain systems, is extended for nonlinear uncertain systems. Second, an adaptive radial basis function neural network estimator-based continuous second order sliding mode control algorithm (CSOSMC-ANNE) is adopted. In CSOSMC-ANNE control methodology, a radial basis function neural network with adaptive parameters is exploited to approximate the unknown system parameters and improve performance against perturbations. Also, the discontinuous switching control of SOSMC is supplanted with a smooth continuous control action to completely eliminate the chattering phenomenon. The convergence and global stability of the closed-loop system are proved using Lyapunov stability method. Numerical computer simulations, with dynamical model of the nonlinear inverted pendulum system, are presented to demonstrate the effectiveness and advantages of the presented control scheme.  相似文献   

4.
This paper presents three fuzzy adaptive controllers for a class of uncertain multivariable nonlinear systems with both sector nonlinearities and dead zones: two first controllers are state feedbacks and the last controller is an output feedback. The design of the first controller concerns systems with symmetric and positive definite control–gain matrix, while the second control design is extended to the case of nonsymmetric control–gain matrix thanks to an appropriate decomposition, namely the product of a symmetric positive definite matrix, a diagonal matrix with diagonal entries +1 or ?1, and a unity upper triangular matrix. The third controller is an output feedback extension of the second controller. In this controller, a high-gain observer is incorporated to estimate the unmeasurable states. An appropriate adaptive fuzzy logic system is used to reasonably approximate the uncertain functions. A Lyapunov approach is adopted to derive the parameter adaptation laws and prove the stability of those control systems as well as the exponential convergence of their underlying tracking errors within an adjustable region. The effectiveness of the proposed fuzzy adaptive controllers is illustrated through simulation results.  相似文献   

5.
The problem of finite-time decentralized neural adaptive constrained control is studied for large-scale nonlinear time-delay systems in the non-affine form. The main features of the considered system are that 1) unknown unmatched time-delay interactions are considered, 2) the couplings among the nested subsystems are involved in uncertain nonlinear systems, 3) based on finite-time stability approach, asymmetric saturation actuators and output constraints are studied in large-scale systems. First, the smooth asymmetric saturation nonlinearity and barrier Lyapunov functions are used to achieve the input and output constraints. Second, the appropriately designed Lyapunov-Krasovskii functional and the property of hyperbolic tangent functions are used to deal with the unknown unmatched time-delay interactions, and the neural networks are employed to approximate the unknown nonlinearities. Note that, due to unknown time-delay interactions and the couplings among subsystems, the controller design is more meaningful and challenging. At last, based on finite-time stability theory and Lyapunov stability theory, a decentralized adaptive controller is proposed, which decreases the number of learning parameters. It is shown that the designed controller can ensure that all closed-loop signals are bounded and the tracking error converges to a small neighborhood of the origin. The simulation studies are presented to show the effectiveness of the proposed method.  相似文献   

6.
Ho HF  Wong YK  Rad AB 《ISA transactions》2008,47(3):286-299
Adaptive fuzzy control is proposed for a class of affine nonlinear systems in strict-feedback form with unknown nonlinearities. The unknown nonlinearities include two types of nonlinear functions: one satisfies the "triangularity condition" and can be directly approximated by fuzzy logic system, while the other is assumed to be partially known and consists of parametric uncertainties. Takagi-Sugeno type fuzzy approximators are used to approximate unknown system nonlinearities and the design procedure is a combination of adaptive backstepping and generalized small gain design techniques. It is proved that the proposed adaptive control scheme can guarantee the uniformly ultimately bounded (UBB) stability of the closed-loop systems. Simulation studies are shown to illustrate the effectiveness of the proposed approach.  相似文献   

7.
This paper presents an adaptive backstepping-based multilevel approach for the first time to control nonlinear interconnected systems with unknown parameters. The system consists of a nonlinear controller at the first level to neutralize the interaction terms, and some adaptive controllers at the second level, in which the gains are optimally tuned using genetic algorithm. The presented scheme can be used in systems with strong couplings where completely ignoring the interactions leads to problems in performance or stability. In order to test the suitability of the method, two case studies are provided: the uncertain double and triple coupled inverted pendulums connected by springs with unknown parameters. The simulation results show that the method is capable of controlling the system effectively, in both regulation and tracking tasks.  相似文献   

8.
This paper investigates the operation of a hybrid power system through a novel fuzzy control scheme. The hybrid power system employs various autonomous generation systems like wind turbine, solar photovoltaic, diesel engine, fuel-cell, aqua electrolyzer etc. Other energy storage devices like the battery, flywheel and ultra-capacitor are also present in the network. A novel fractional order (FO) fuzzy control scheme is employed and its parameters are tuned with a particle swarm optimization (PSO) algorithm augmented with two chaotic maps for achieving an improved performance. This FO fuzzy controller shows better performance over the classical PID, and the integer order fuzzy PID controller in both linear and nonlinear operating regimes. The FO fuzzy controller also shows stronger robustness properties against system parameter variation and rate constraint nonlinearity, than that with the other controller structures. The robustness is a highly desirable property in such a scenario since many components of the hybrid power system may be switched on/off or may run at lower/higher power output, at different time instants.  相似文献   

9.
针对具有模型不确定且参数未知的单输入单输出的非线性系统的特点,文中提出了一种自适应反馈控制方法。该方法中,假设系统被调整量最高阶导数的理想值为已知。由于方法仅需要对被控对象的调整量的输出进行反馈,而不要求状态量的具体值,所以降低了算法实现的难度。通过数值仿真验证了方法的可行性和有效性。  相似文献   

10.
Recently, the combination of sliding mode and fuzzy logic techniques has emerged as a promising methodology for dealing with nonlinear, uncertain, dynamical systems. In this paper, a sliding mode control algorithm combined with a fuzzy control scheme is developed for the trajectory control of a command guidance system. The acceleration command input is mathematically derived. The proposed controller is used to compensate for the influence of unmodeled dynamics and to alleviate chattering. Simulation results show that the proposed controller gives good system performance in the face of system parameters variation and external disturbances. In addition, they show the effectiveness of the proposed missile guidance law against different engagement scenarios where the results demonstrate better performance over the conventional sliding mode control.  相似文献   

11.
振动自适应模糊控制方法研究   总被引:1,自引:0,他引:1  
屈文忠  邱阳 《机械科学与技术》1998,17(6):996-998,1001
将自适应模糊控制理论引入振动控制工程领域,提出了一种基于模糊逻辑系统的在线自学习控制方法。给出了该控制方法的学习算法及初始振动模糊控制器的产生方法。分析了该方法与其它非线性控制方法(神经网络控制)相比所具有的优点。仿真结果表明该自适应模糊控制方法能有效地抑制振动。  相似文献   

12.
防抱制动系统参数自适应滑模变结构控制器的研究   总被引:9,自引:0,他引:9  
首先针对具有参数不确定性的二阶非线性系统提出了自适应滑模变结构的控制算法 ,该算法的基本思想是用自适应策略来估计不确定系统的参数 ,根据估计出的参数值 ,来设计滑模控制器 ,优点是无须事先已知不确定参数的边界 ,并且由于在自适应变结构控制采用了消颤措施 (增加了消颤项 ) ,能削弱常规滑模控制所引起的颤振现象 ,也能提高单纯的自适应控制的鲁棒性能。而后将这一控制策略应用于防抱死制动系统 (ABS)的研究中 ,设计了防抱死制动系统的自适应滑模变结构控制器 ,通过计算机仿真 ,验证了该控制方案在 ABS应用中的可行性和有效性  相似文献   

13.
This paper presents a new discrete-time adaptive second-order sliding mode control with time delay estimation (TDE) for a class of uncertain nonlinear time-varying strict-feedback systems. The existing researches on time delay control (TDC) are conventionally established based on a stability criterion that is subject to the infinitesimal time delay assumption. Recently, this criterion was rejected and a new criterion was proposed for the development of a controller for systems with fully known dynamics. In this study, this approach is extended to uncertain systems. Specifically, a new criterion is developed for the stability of the TDE-error within an adaptive robust controller design without the infinitesimal time delay assumption. With the proposed adaptive robust control, there is no need for determination of uncertainties upper-bounds. Simulation results illustrate the efficacy of the proposed controller.  相似文献   

14.
In this paper, an adaptive disturbance estimation-based control of a class of uncertain feedback linearizable systems with the presence of, both, external perturbations as well as non-modeled dynamics is considered. The aim of the control design was to solve the tracking trajectory problem for a class of output-based linearizable uncertain systems. An adaptive scheme is proposed for developing a state estimator of the uncertain dynamics. The estimation of both, the states and the uncertain dynamics is attained despite the limited knowledge of the plant and the information contained in the output signal. The uncertain section in the linearized system was approximated by a class of time-dependent combination of the system states. The observer implemented a parametric identifier to obtain the time varying parameters associated to the estimation of the uncertain section. This method ensured the adequate estimation process of the uncertainties/perturbations, measured in terms of the mean square error. Simultaneously, an adaptive gain associated to the observer adjusts its trajectories to provide the ultimate boundedness of the estimation error. Once the states of the uncertain system are obtained, a feedback controller rejects actively the perturbations that affect the system by a compensation scheme. Two numerical examples were developed to show the observer-based control performance.  相似文献   

15.
In this paper, the global output tracking is investigated for a class of uncertain nonlinear hysteretic systems with nonaffine structures. By combining the solution properties of the hysteresis model with the novel backstepping approach, a robust adaptive control algorithm is developed without constructing a hysteresis inverse. The proposed control scheme is further modified to tackle the bounded disturbances by adaptively estimating their bounds. It is rigorously proven that the designed adaptive controllers can guarantee global stability of the closed-loop system. Two numerical examples are provided to show the effectiveness of the proposed control schemes.  相似文献   

16.
It is well known that surface alloying quality may vary significantly with respect to process parameter variation. Thus a feedback control system is required to monitor the operating parameters for yielding a good quality control. Since this multi-input and multi-output (MIMO) system has nonlinear coupling and time-varying dynamic characteristics, it is very difficult to establish an accurate process model for designing a model-based controller. Hence an adaptive fuzzy sliding-mode controller (AFSMC) which combines an adaptive rule with fuzzy and sliding-mode control is employed in this study. It has an on-line learning ability for responding to a system’s nonlinear and time-varying behaviours. Two adaptive fuzzy sliding-mode controllers are designed for tuning the laser power and the traverse velocity simultaneously to tackle the absorptivitiy and geometrical variations of the work pieces. The simulation results show that good surface lapping performance is achieved by using this intelligent control strategy.  相似文献   

17.
In this paper, an adaptive control method using multiple models with second level adaptation is proposed for a class of nonlinear multi-input multi-output (MIMO) coupled systems. Multiple estimation models are used to tune the unknown parameters at the first level. The second level adaptation provides a single parameter vector for the controller. A feedback linearization technique is used to design a state feedback control. The efficacy of the designed controller is validated by conducting real time experiment on a laboratory setup of twin rotor MIMO system (TRMS). The TRMS setup is discussed in detail and the experiments were performed for regulation and tracking problem for pitch and yaw control using different reference signals. An Extended Kalman Filter (EKF) has been used to observe the unavailable states of the TRMS.  相似文献   

18.
This paper investigates an adaptive sampling rate control scheme for networked control systems (NCSs) subject to packet disordering. The main objectives of the proposed scheme are (a) to avoid heavy packet disordering existing in communication networks and (b) to stabilize NCSs with packet disordering, transmission delay and packet loss. First, a novel sampling rate control algorithm based on statistical characteristics of disordering entropy is proposed; secondly, an augmented closed-loop NCS that consists of a plant, a sampler and a state-feedback controller is transformed into an uncertain and stochastic system, which facilitates the controller design. Then, a sufficient condition for stochastic stability in terms of Linear Matrix Inequalities (LMIs) is given. Moreover, an adaptive tracking controller is designed such that the sampling period tracks a desired sampling period, which represents a significant contribution. Finally, experimental results are given to illustrate the effectiveness and advantages of the proposed scheme.  相似文献   

19.
This paper presents the output-feedback fuzzy proportional-integral (PI) controller design for uncertain nonlinear systems with both fully delayed input and output. Based on the Takagi–Sugeno (T–S) fuzzy model representation, the output-feedback PI control is realized via parallel distributed PI compensation and novel LMI gain design. Although the T–S fuzzy PI controller is simple, asymptotic output regulation is assured to overcome the effect of uncertainty, state delay, and full input/output delays. When considering disturbance and measurement noise, the control performance is achieved by robust gain design. Furthermore, state observers and bilinear matrix inequality conditions are removed in this paper. Finally, time-delay Chua׳s circuit system and a continuous-time stirred tank reactor are taken as applications to show the expected performance.  相似文献   

20.
Variances of the system states or outputs often play vital roles in the problem for performance requirements of many stochastic control systems. For linear stochastic systems, the covariance control technique has been applied to deal with the variance constrained design problem. This paper extends this technique to a class of discrete-time nonlinear perturbed stochastic systems, which are modeled by the Takagi-Sugeno (TS) fuzzy systems. By fuzzy IF-THEN rules, which represent local linear input-output relations, the nonlinear systems can be described by TS fuzzy models. According to the parallel distributed compensation (PDC) concept, the discrete-time nonlinear perturbed stochastic systems can be driven by the linear feedback gains. The purpose of this paper is to provide a method to design an output feedback fuzzy controller, which is based on the upper bound state covariance control technique and PDC concept, for the discrete-time perturbed stochastic systems using TS fuzzy models.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号