溶胶-凝胶法制备La2Ce2O7:Eu3+及其发光性能

采用溶胶-凝胶法（Sol-gel）合成La₂Ce₂O₇:Eu3+系列红色荧光粉,并研究煅烧温度、Eu3+掺杂浓度以及不同种类电荷补偿剂对样品发光性能的影响.通过XRD、SEM、荧光光谱对样品的晶体结构、形貌以及发光性能进行测量和表征.结果表明:实验所得样品主晶相为La₂Ce₂O₇,属于萤石结构. Eu3+及电荷补偿剂的掺杂没有改变其晶体结构.合成的样品在467 nm蓝光激发下发出612 nm的红光.样品的发光强度随煅烧温度以及Eu3+掺杂浓度的提高先增强后减弱,样品的较优的煅烧温度为1 100 ℃,Eu3+较优的掺杂浓度为10 %（摩尔百分比）.掺入电荷补偿剂可以有效增强样品的发光强度,其中掺入Li+后发光增强的效果最显著.      

红色荧光粉La2O3：Eu3＋的合成及发光性质

利用复合沉淀法制备了性能稳定的红色荧光粉La2O3：Eu3＋,同时研究了煅烧温度及掺杂Eu3＋浓度对La2O3：Eu。’发光性能的影响．通过X射线粉末衍射（XRD）和扫描电子显微镜（SEM）来表征荧光粉的晶体结构和颗粒大小及形貌：用激发光谱和发射光谱以及荧光衰减曲线来袁征荧光粉的荧光性能．结果表明：煅烧温度在900℃时,所制备样品为六方晶系La2O3：Eun;SEM图显示掺杂Eu0＋含量为5％的La2O3颗粒直径为15μm左右．最大发射波长和激发波长分别为626nm和396nm,发射光谱中596nm和626nm的发射峰对应的是Eu3＋离子的0D—F1和5D—F2跃迁,其荧光寿命为0．754ms．     

微波辅助液相沉淀法合成Ca(MoO4)1-x(WO4)x:Eu3+红色荧光粉

以尿素为沉淀剂，采用微波辅助液相沉淀法合成了类球状双基质Ca(MoO₄)_1-x(WO₄)_x:Eu3+红色荧光粉，通过采用XRD、SEM、荧光光谱(PL)等现代分析技术对荧光粉的结构、形貌及发光性能进行了表征.结果表明，制备的Ca(MoO₄)_1-x(WO₄)_x:Eu3+红色荧光粉晶型完整，纯度高，为白钨矿结构；掺杂WO₄2-离子后，CaMoO₄:Eu3+红色荧光粉的发光性能明显增强，当WO₄2-离子的掺杂量x=0.4时，在395 nm激发下，在616 nm处的主发射峰的发光强度达到最大，掺杂浓度过高时会出现浓度淬灭现象.其较优的煅烧温度为1 000 ℃，煅烧时间为4 h.      

白光LED用LaPO4:Eu3+红色荧光粉的合成与表征

利用水热法制备了性能稳定的红色荧光粉LaPO4:Eu3+,同时研究了不同的Eu3+浓度、煅烧温度对荧光粉发光性能的影响.通过X射线粉末衍射(XRD)和扫描电子显微镜(SEM)来表征荧光粉的晶体结构和颗粒大小及形貌;用激发光谱和发射光谱以及荧光衰减曲线来表征荧光粉的荧光性能.结果表明:未煅烧时前躯体主要是六方晶相LaPO4·0.5H2O,煅烧温度在900℃时,所制备样品为单斜相LaPO4:Eu3+;SEM图像显示5 at.%Eu3+掺杂LaPO4呈椭球形,颗粒长约为500 nm,宽约为300 nm.最大发射波长和激发波长分别为592 nm和393 nm,发射光谱中592 nm和612 nm的发射峰对应的是Eu3+离子的5D0→7F1和5D0→7F2跃迁.其荧光寿命为3.32 ms.     

Ca2+、La3+掺杂纳米Y2O3∶Eu3+的超声波制备及光致发光性能

采用超声波作用下的均匀沉淀法制备Ca2 、La3 掺杂的纳米Y2O3∶Eu3 荧光粉.通过正交实验研究掺杂浓度、溶液pH、超声功率、反应时间、干燥温度、煅烧温度等因素对其光致发光(PL)性能的影响,得到制备Ca2 、La3 掺杂纳米Y2O3∶Eu3 的最佳条件.结果表明,超声功率、Eu(NO3)3浓度、尿素体积、氨水浓度、煅烧温度是影响样品PL强度的主要因素.Ca2 、La3 离子单一掺杂效果优于两种元素的复合掺杂,最佳条件下制备的Ca2 、La3 分别掺杂的纳米Y2O3∶Eu3 荧光粉的发光性能均显著优于未掺杂样品.     

红色Sr1-2xNaXWO4:Eu3+x荧光体的制备与发光性能

采用传统高温固相法,以钨酸锶为基质材料,掺杂稀土Eu3+制备了可被紫色光有效激发的红色荧光粉Sr1-2xNaxWO4:Eu3+x.通过测定与分析样品Sr1-2xNaxWO4:Eu3+x的激发和发射光谱,发现激发光谱在395nm处吸收值最大,发射光谱的发射主峰位于613nm处,属于Eu3+的5 D0→7F2特征跃迁.不同的Eu3+掺杂浓度下样品发光强度不同,当x =0.07时发光强度最佳.电荷补偿剂Na+对样品发光强度的影响很大,主要原因是Na+的加入会影响基质的晶体结构,当Na+的含量与Eu3+含量相同时样品发光强度最好,Na+含量增加到一定程度后基质结晶不完善,荧光体的发光强度急剧下降.     

水热法制备Y2O3：Eu及其发光性能的研究

利用水热法制备立方相Y2O3：Eu红色荧光粉.在不同掺杂浓度、不同溶液pH值的系列样品中,均观测到Eu3＋离子的特征发射.荧光强度与Eu3＋离子掺杂浓度关系研究表明：在不同掺杂浓度中,Eu3＋离子掺杂浓度为9%时其相对发射强度最强.在不同溶液pH值所获得的样品中,以溶液pH等于6制备的样品发光效果最好.此外通过与商用Y2O3：Eu红色荧光粉比较,发现其荧光强度相当.因此,与传统高温固相法相比,水热法合成Y2O3：Eu红色荧光粉是简单易行方案.     

红色Sr1-2xNaxWO4∶Eux3+荧光体的制备与发光性能

采用传统高温固相法,以钨酸锶为基质材料,掺杂稀土Eu3+制备了可被紫色光有效激发的红色荧光粉Sr1-2xNaxWO4∶Eu3x+。通过测定与分析样品Sr1-2xNaxWO4∶Eu3x+的激发和发射光谱,发现激发光谱在395nm处吸收值最大,发射光谱的发射主峰位于613nm处,属于Eu3+的5D0→7F2特征跃迁。不同的Eu3+掺杂浓度下样品发光强度不同,当x=0.07时发光强度最佳。电荷补偿剂Na+对样品发光强度的影响很大,主要原因是Na+的加入会影响基质的晶体结构,当Na+的含量与Eu3+含量相同时样品发光强度最好,Na+含量增加到一定程度后基质结晶不完善,荧光体的发光强度急剧下降。     

蓝光激发锡酸盐红色荧光粉的光谱性能

采用高温固相法合成了Sr2-xSnO4∶Eu3+x系列红色发光粉,该荧光粉属于四方晶系结构。以465 nm的蓝光激发样品,Sr2-xSnO4∶Eu3+x荧光粉发射红光,以Eu3+的5D0-7F2电偶极跃迁发光最强。该材料能非常好地吸收465 nm波长的光。研究了激活剂Eu3+的浓度对Sr2-xSnO4∶Eu3+x样品发光性能的影响。结果表明,Eu3+的最佳掺杂浓度为5%。     

水热法制备Y_2O_3:Eu及其发光性能的研究

利用水热法制备立方相Y2O3:Eu红色荧光粉.在不同掺杂浓度、不同溶液pH值的系列样品中,均观测到Eu3+离子的特征发射.荧光强度与Eu3+离子掺杂浓度关系研究表明:在不同掺杂浓度中,Eu3+离子掺杂浓度为9%时其相对发射强度最强.在不同溶液pH值所获得的样品中,以溶液pH等于6制备的样品发光效果最好.此外通过与商用Y2O3:Eu红色荧光粉比较,发现其荧光强度相当.因此,与传统高温固相法相比,水热法合成Y2O3:Eu红色荧光粉是简单易行方案.     

Luminescent characteristics of LiCaBO3：Eu^3＋ phosphor for white light emitting diode

LiCaBO3:Eu3+ phosphor was synthesized by high solid-state reaction method, and its luminescent characteristics were investigated. The emission and excitation spectra of LiCaBO3:Eu3+ phosphors exhibited that the phosphors could be effectively excited by near ultraviolet (400 nm) and blue (470 nm) light, and emitted red light. The effect of Eu3+ concentration on the emission spectrum of LiCaBO3:Eu3+ phos-phor was studied. The results showed that the emission intensity increased with increasing Eu3～ concentration, and then decreased because of concentration quenching. It reached the maximum at 3mol.% Eu3+, and the concentration self-quenching mechanism was the d-d interaction according to the Dexter theory. Under the conditions of charge compensator Li+, Na+ or K+ incorporated in LiCaBO3, the emission intensities of LiCaBO3:Eu3+ phosphor were enhanced.     

Luminescent properties of red phosphors K2Ba（MoO4）2：Eu3＋ for white light emitting diodes

K2Ba(MoO4)2:Eu3+ phosphors were synthesized by solid-state reaction. The emission and excitation spectra of K2 Ba(MoO4)2:Eu3+ phosphors exhibited that the phosphors could be effectively excited by near ultraviolet (394 nm) and blue (465 nm) light, and emitted red light at 616 nm. The influence of Eu3+concentration, sintering temperature and charge compensators (K+, Na+ or Li+ ) on the emission intensity were investigated. The results indicated that concentration quenching of Eu3+ was not observed within 30mol.% Eu 3+, 600 oC was a suitable sintering temperature for preparation of K2 Ba(MoO4)2:Eu3+phosphors, and K+ ions gave the best improvement to enhance the emission intensity. The CIE chromaticity coordinates of K2 Ba(MoO4)2:0.05Eu3+phosphor were calculated to be (0.68, 0.32), and color purity was 97.4%.     

Synthesis and luminescence properties of europium activated Ca3Al2O6-Sr3Al2O6 system

Divalent europium activated tristrontium dialuminum hexaoxide phosphor, (Sr1-xEux)3Al2O6, was obtained by solid state reaction. Crystal structure and luminescence properties of synthesized (Sr1-xEux)3Al2O6 were investigated. The major excitation band of (Sr1-xEux)3Al2O6 located in blue light region, the photoluminescence spectrum showed red light emission peaked at 618 nm which could be attributed to the d-f transition of the Eu2+. The influence of Ca2+ substitution for Sr2+ on structural and luminescence properties of Eu2+ doped Sr3Al2O6 was also studied. The photoluminescence peak position of (Sr1-yCay)2.94Eu0.06Al2O6 varied from 618 to 655 nm with increasing y value. The reason for redshift in the emission band of (Sr1-yCay)2.94Eu0.06Al2O6 phosphor was also discussed.     

水热法制备Y2O3:Eu及其发光性能的研究

利用水热法制备立方相Y₂O₃:Eu红色荧光粉.在不同掺杂浓度、不同溶液pH值的系列样品中,均观测到Eu3+离子的特征发射.荧光强度与Eu3+离子掺杂浓度关系研究表明:在不同掺杂浓度中,Eu3+离子掺杂浓度为9 %时其相对发射强度最强.在不同溶液pH值所获得的样品中,以溶液pH等于6制备的样品发光效果最好.此外通过与商用Y₂O₃:Eu红色荧光粉比较,发现其荧光强度相当.因此,与传统高温固相法相比,水热法合成Y₂O₃:Eu红色荧光粉是简单易行方案.      

Luminescent Properties of Green Phosphor Ca8Mg（SiO4 ）4 Cl2：EU^2＋ , DY^3＋ for LED Applications

The new phosphor calcium magnesium chlorosilicate, codoped with Eu^2＋ and Dy^3＋, was synthesized with the help of the high temperature solid state reaction in reducing atmosphere. The excitation and emission spectra were very similar to that of Ca8Mg（SiO4）4Cl2 ：Eu^2＋, and the Dy^3＋ concentration influenced the emission intensity of this phosphor. The intensity of Eu^2＋ and Dy^3＋ codoped CMSC was stronger than that of Eu^2＋ singly doped CMSC. The emission spectrum of the Dy^3＋ ion overlapped the absorption band of the Eu^2＋ ion, indicating that an energy transfer from Dy^3＋ to Eu^2＋ took place in CMSC：Eu^2＋, Dy^3＋ phosphor. The mechanism of the energy transfer from Dy^3＋ tO Eu^2＋, in this phosphor, might be resonant energy transfer.     

Luminescent properties of Ba3Gd（BO3）3：Eu^3＋ phosphor for white LED applications

Luminescent material Ba3Gd(BO3)3 doped with Eu3+ ion was prepared by high temperature solid-state method. The preparing conditions, luminescent properties, and particle morphology of Ba3Gd(BO3)3:Eu3 + phosphor were studied with X-ray diffraction (XRD), fluorescence spectroscopy, and scanning electron microscopy (SEM). The results obtained by XRD showed that pure phase of Ba3Gd(BO3)3 was obtained at 1000℃. Images from SEM displayed that the particles of Ba3Gd(BO3)3:Eu3+ phosphor had a spherical shape with an average diameter of about 200-400 nm. The luminescence spectra showed that Ba3Gd(BO3)3:Eu3+ phosphor was effectively excited by the near ultraviolet (UV) light (396 nm) and blue light (466 nm). The main emission peaks of Ba3Gd(BO3)3:Eu3+ phosphor were assigned to the supersensitive transition 5D0-7F2 (611 and 616 nm) of Eu3+ ion when samples were excited at 255 and 396 nm, respectively, and the luminescent intensity of Ba3Gd(BO3)3:Eu3+ at 611 and 616 nm reached to the maximum when the doped content of Eu3+ ion was 10mol.%. Therefore, this phosphor could be a promising red component for possible applications in the field of white LED.     

作为白光LED用铕掺杂氟化镧红色荧光粉的制备与光谱性能研究

采用水热法制备具有单一相六方晶系的LaF₃:Eu3+纳米荧光粉.通过X射线粉末衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)、光致发光光谱(PL)和荧光衰减曲线对LaF₃:Eu3+纳米荧光粉进行表征.LaF₃:Eu3+荧光粉的激发光谱主要由250 nm处的宽带(O2-→Eu3+的电荷转移跃迁)和一些尖峰(Eu3+ f-f跃迁)构成,其中位于近紫外区396 nm处有一较强的激发峰.通过发射光谱探测Eu3+在LaF₃晶体中的局部晶场环境.在298 K下激发光谱和发射光谱可知,在六方晶系的LaF₃纳米晶体中的Eu3+晶格位置从D_4h降至到C_2v,这是由于晶格变化所造成的.在396 nm激发下,观测到较优掺杂浓度为10%的LaF₃:Eu3+荧光粉在591 nm(5D₀→7F₁跃迁)处有强烈的红色发射峰.其发光性能表明,LaF₃:Eu3+红色荧光粉在近紫外发光二极管领域具有潜在的应用价值.      

Eu3+激活的Li2Gd4（MoO4）7钼酸盐红色荧光体及其发光性质

由高温固相反应首次合成Li2(Gd1-xEux)4(MoO4)7(0相似文献