Comparative study of EMI shielding effectiveness for carbon fiber pultruded polypropylene/poly(lactic acid)/multiwall CNT composites prepared by injection molding versus screw extrusion

The electrical conductivity and electromagnetic interference (EMI) shielding effectiveness of the composites of polypropylene/poly(lactic acid) (PP/PLA) (70/30, wt %) with single filler of multiwall carbon nanotube (CNT) or hybrid fillers of nickel‐coated carbon fiber (CF) and CNT were investigated. For the single filler composite, higher electrical conductivity was observed when the PP‐g‐maleic anhydride was added as a compatibilizer between the PP and PLA. For the composite of the PP/PLA (70/30)/CF (20 phr)/CNT (5 phr), the composite prepared by injection molding observed a higher EMI shielding effectiveness of 50.5 dB than the composite prepared by screw extrusion (32.3 dB), demonstrating an EMI shielding effectiveness increase of 49.8%. The higher values in EMI shielding effectiveness and electrical conductivity of the PP/PLA/CF (20 phr)/CNT (5 phr) composite seemed mainly because of the increased CF length when the composites were prepared using injection molding machine, compared with the composites prepared by screw extrusion. This result suggests that the fiber length of the conductive filler is an important factor in obtaining higher values of electrical conductivity and EMI shielding effectiveness of the PP/PLA/CF/CNT composites. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45222.     

Electrical,rheological and electromagnetic interference shielding properties of thermoplastic polyurethane/carbon nanotube composites

Electrically conducting rubbery composites based on thermoplastic polyurethane (TPU) and carbon nanotubes (CNTs) were prepared through melt blending using a torque rheometer equipped with a mixing chamber. The electrical conductivity, morphology, rheological properties and electromagnetic interference shielding effectiveness (EMI SE) of the TPU/CNT composites were evaluated and also compared with those of carbon black (CB)‐filled TPU composites prepared under the same processing conditions. For both polymer systems, the insulator–conductor transition was very sharp and the electrical percolation threshold at room temperature was at CNT and CB contents of about 1.0 and 1.7 wt%, respectively. The EMI SE over the X‐band frequency range (8–12 GHz) for TPU/CNT and TPU/CB composites was investigated as a function of filler content. EMI SE and electrical conductivity increased with increasing amount of conductive filler, due to the formation of conductive pathways in the TPU matrix. TPU/CNT composites displayed higher electrical conductivity and EMI SE than TPU/CB composites with similar conductive filler content. EMI SE values found for TPU/CNT and TPU/CB composites containing 10 and 15 wt% conductive fillers, respectively, were in the range ?22 to ?20 dB, indicating that these composites are promising candidates for shielding applications. © 2013 Society of Chemical Industry     

EMI shielding effectiveness of carbon based nanostructured polymeric materials: A comparative study

The microstructure, electromagnetic interference (EMI) shielding effectiveness (SE), DC electrical conductivity, AC electrical conductivity and complex permittivity of nanostructured polymeric materials filled with three different carbon nanofillers of different structures and intrinsic electrical properties were investigated. The nanofillers were multiwall carbon nanotubes (MWCNT), carbon nanofibers (CNF) and high structure carbon black (HS-CB) nanoparticles and the polymer was acrylonitrile-butadiene-styrene (ABS). In addition, the EMI SE mechanisms and the relation between the AC electrical conductivity in the X-band frequency range and the DC electrical conductivity were studied. The nanocomposites were fabricated by solution mixing and characterized by uniform dispersion of the nanofillers within the polymer matrix. It was found that, at the same nanofiller loading, the EMI SE, permittivity and electrical conductivity of the nanocomposites decreased in the following order: MWCNT > CNF > CB. MWCNT based nanocomposites exhibited the lowest electrical percolation threshold and the highest EMI SE owning to the higher aspect ratio and electrical conductivity of MWCNT compared to CNF and HS-CB. The AC conductivity in the X-band frequency range was found to be independent of frequency.     

Electrical conductivity and EMI shielding effectiveness of polyurethane foam–conductive filler composites

The morphological, electrical, and thermal properties of polyurethane foam (PUF)/single conductive filler composites and PUF/hybrid conductive filler composites were investigated. For the PUF/single conductive filler composites, the PUF/nickel‐coated carbon fiber (NCCF) composite showed higher electrical conductivity and electromagnetic interference shielding effectiveness (EMI SE) than did the PUF/multiwall carbon nanotube (MWCNT) and PUF/graphite composites; therefore, NCCF is the most effective filler among those tested in this study. For the PUF/hybrid conductive fillers PUF/NCCF (3.0 php)/MWCNT (3.0 php) composites, the values of electrical conductivity and EMI SE were determined to be 0.171 S/cm and 24.7 dB (decibel), respectively, which were the highest among the fillers investigated in this study. NCCF and MWCNT were the most effective primary and secondary fillers, and they had a synergistic effect on the electrical conductivity and EMI SE of the PUF/NCCF/MWCNT composites. From the results of thermal conductivity and cell size of the PUF/conductive filler composites, it is suggested that a reduction in cell size lowers the thermal conductivity of the PUF/conductive filler composites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44373.     

Investigation of the electric conductivity and the electromagnetic interference shielding efficiency of SWCNTs/GNS/PAni nanocomposites

This work demonstrates the fabrications and characterizations of polyaniline (PAni) composites containing single-walled carbon nanotubes (SWCNTs), graphite nanosheets (GNS), or hybrid fillers (SWCNTs/GNS). The characterization of microstructure, examination of fracture surface morphologies, and measurement of electric conductivity and electromagnetic interference shielding efficiency (EMI SE) were performed. It was found that both the electric conductivity and the EMI SE increase with filler loading, and the nanocomposites filled with 1.0 wt.% SWCNTs/GNS possessed the highest electric conductivity of 16.2 S/cm and total EMI SE of 27.0 dB. The experimental results also show that absorption is the primary mechanism of EMI SE for all of the loadings and fillers.     

Electrical and mechanical properties of carbon nanotube‐epoxy nanocomposites

In this work, electrical conductivity and thermo‐mechanical properties have been measured for carbon nanotube reinforced epoxy matrix composites. These nanocomposites consisted of two types of nanofillers, single walled carbon nanotubes (SW‐CNT) and electrical grade carbon nanotubes (XD‐CNT). The influence of the type of nanotubes and their corresponding loading weight fraction on the microstructure and the resulting electrical and mechanical properties of the nanocomposites have been investigated. The electrical conductivity of the nanocomposites showed a significantly high, about seven orders of magnitude, improvement at very low loading weight fractions of nanotubes in both types of nanocomposites. The percolation threshold in nanocomposites with SW‐CNT fillers was found to be around 0.015 wt % and that with XD‐CNT fillers around 0.0225 wt %. Transmission optical microscopy of the nanocomposites revealed some differences in the microstructure of the two types of nanocomposites which can be related to the variation in the percolation thresholds of these nanocomposites. The mechanical properties (storage modulus and loss modulus) and the glass transition temperature have not been compromised with the addition of fillers compared with significant enhancement of electrical properties. The main significance of these results is that XD‐CNTs can be used as a cost effective nanofiller for electrical applications of epoxy based nanocomposites at a fraction of SW‐CNT cost. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synergistic effects of hybrid carbon nanomaterials in room‐temperature‐vulcanized silicone rubber

This work examines nanocomposites based on nanofillers and room‐temperature‐vulcanized silicone rubber. The carbon nanofillers used were conductive carbon black (CB), carbon nanotubes (CNTs) and graphene (GE). Vulcanizates for CB, GE, CNTs as the only filler and hybrid fillers using CNTs, CB and GE were prepared by solution mixing. The elastic modulus for CNT hybrid with CB at 15 phr (4.65 MPa) was higher than for CB hybrid with GE (3.13 MPa) and CNTs/CB/GE as the only filler. Similarly, the resistance for CNT hybrid with CB at 10 phr (0.41 kΩ) was lower than for CB (0.84 kΩ) at 20 phr and CNTs as the only filler. These improvements result from efficient filler networking, a synergistic effect among the carbon nanomaterials, the high aspect ratio of CNTs and the improved filler dispersion in the rubber matrix. © 2016 Society of Chemical Industry     

Electrical behavior and positive temperature coefficient effect of graphene/polyvinylidene fluoride composites containing silver nanowires

Polyvinylidene fluoride (PVDF) composites filled with in situ thermally reduced graphene oxide (TRG) and silver nanowire (AgNW) were prepared using solution mixing followed by coagulation and thermal hot pressing. Binary TRG/PVDF nanocomposites exhibited small percolation threshold of 0.12 vol % and low electrical conductivity of approximately 10^-7 S/cm. Hybridization of TRGs with AgNWs led to a significant improvement in electrical conductivity due to their synergistic effect in conductivity. The bulk conductivity of hybrids was higher than a combined total conductivity of TRG/PVDF and AgNW/PVDF composites at the same filler loading. Furthermore, the resistivity of hybrid composites increased with increasing temperature, giving rise to a positive temperature coefficient (PTC) effect at the melting temperature of PVDF. The 0.04 vol % TRG/1 vol % AgNW/PVDF hybrid exhibited pronounced PTC behavior, rendering this composite an attractive material for making current limiting devices and temperature sensors.     

In situ polymerization of polyurethane‐silver nanocomposite foams with intact thermal stability,improved mechanical performance,and induced antimicrobial properties

Silver nanoparticle‐reinforced thermoplastic polyurethane (PU/AgNP) nanocomposite foams were prepared using in situ polymerization techniques in accordance with DOW chemicals’ industrial standards. The foams exhibited improved mechanical performance, induced antimicrobial properties, and intact stability when subjected to a thermal degradation treatment. Scanning electron microscopy (SEM) indicated a homogeneous dispersion of the silver nanoparticle (AgNP) within the polymeric matrix at low filler loadings and a cluster formation at higher loadings. SEM also indicated the agglomeration of the silver nanofiller particles as a result of the thermal degradation treatment, which caused them to lose their nanoscopic characteristics and act as ordinary silver metal. Molecular modeling techniques were used to explain these observations and confirmed the higher repulsive interactions between the polymer chains and the silver nanoparticles with the increase in the nanofiller content. Stress relaxation of the nanocomposites showed optimum mechanical performance and lowest hysteresis for the 0.1% AgNP nanocomposites due to the confinement of the PU chains between the large number of the nanoparticles. Incubation with 0.1% foam inhibited the growth of Klebseilla spp. and Escherichia coli and to some extent Staphylococcus spp. This is very interesting as the same nanocomposite loaded with 0.1% AgNp has also shown the best mechanical performance highlighting the strong action of this “unclustered” low concentration on both the material and biomedical sides. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43125.     

Barrier properties of thermal and electrical conductive hydrophobic multigraphitic/epoxy coatings

Epoxy composites doped with different content of graphene nanoplatelets (GNPs) and/or carbon nanotubes (CNTs) have been manufactured. Their chemical, thermal, electrical, and mechanical behaviors have been studied, evaluating also their performance as coatings of glass fiber composite substrates. It is confirmed that the graphitic nanofillers present different efficiency as nanofillers as a function of their geometry. CNTs are much higher efficient electrical nanofillers than graphene, but an important synergetic effect is determined in the electrical conductivity of hybrid GNP/CNT/epoxy composites. In contrast, the thermal conductivity scarcely depends on the geometry of graphitic nanofillers but on the graphitic nanofiller content. Adding up to 12 wt% GNP and 1 wt% CNT, the thermal conductivity of the epoxy resin can be increased more than 300%. GNP presents high efficiency to increase the barrier properties, reducing the water absorption up to 30%. The stiffness of nanocomposites proportionally increases with graphitic addition, up to 50%, regard to the modulus of the neat epoxy resin. The adherence of coatings over glass fiber composite substrates increases by nanofiller addition due to the nanomechanical anchoring. However, the water uptake induces a higher weakening on nanodoped composites due to the preferential water absorption by the interface.     

Flexible poly(styrene-b-(ethylene-co-butylene)-b-styrene) nanocomposites for electromagnetic interference shielding

In this report, multiwalled carbon nanotubes (CNT) embedded poly(styrene-b-(ethylene-co-butylene)-b-styrene) (SEBS) microspheres (CNT/SEBS) were prepared by solvent evaporation method. Reduced graphene oxide (rGO) nanosheets were used to cover the surface of CNT/SEBS microspheres. The CNT/SEBS/rGO nanocomposites with special segregated conductive network were fabricated by hot pressing these as-prepared complex microspheres. The morphology, electrical percolation threshold, electrical conductivity, and electromagnetic interference (EMI) shielding effectiveness (SE) of CNT/SEBS/rGO composites were characterized. The shielding mechanisms were discussed in detail. Analysis of electrical conductive performance shows that the electrical percolation threshold of rGO is 0.22 vol %. Results of EMI shielding test confirmed the synergistic effect between CNT and rGO. The EMI SE of the composite filled by 2.1 vol % CNT and 3.35 vol % rGO can achieve 26 dB in 8.2− 12.4 GHz (X band), which exceeds the basic requirement for commercial application (20 dB). Its reflectance coefficient (19–41%) indicates that the most part of incident electromagnetic (EM) wave energy is attenuated through absorption mechanism. This kind of absorptive EMI shielding material can be applied without serious secondary EM radiation pollution problems. The effects of filler content, molding temperature on EMI SE, and shielding mechanism were also investigated. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48542.     

Effects of hybrid fillers on the electrical conductivity,EMI shielding effectiveness,and flame retardancy of PBT and PolyASA composites with carbon fiber and MWCNT

The effects of hybrid fillers of carbon fiber (CF) and multiwall carbon nanotube (MWCNT) on the electrical conductivity, electromagnetic interference shielding effectiveness (EMI SE), flame retardancy, and mechanical properties of poly(butylene terephthalate) (PBT)/poly(acrylonitrile-co-styrene-co-acrylate) (PolyASA) (70/30, wt %) with conductive filler composites were investigated. The CF was used as the main filler, and MWCNT was used as the secondary filler to investigate the hybrid filler effect. For the PBT/PolyASA/CF (8 vol %)/MWCNT (2 vol %) composite, a higher electrical conductivity (1.4 × 10⁰ S cm⁻¹) and EMI SE (33.7 dB) were observed than that of the composite prepared with the single filler of CF (10 vol %), which were 9.0 × 10⁻² S cm⁻¹ and 23.7 dB, respectively. This increase in the electrical properties might be due to the longer CF length and hybrid filler effect in the composites. From the results of aging test at 85 °C, 120 h, the electrical conductivity and EMI SE of the composites decreased slightly compared to that of the composite without aging. The results of electrical conductivity, EMI SE, and flame retardancy suggested that the composite with the hybrid fillers of CF and MWCNT showed a synergetic effect in the PBT/PolyASA/CF (8 vol %)/MWCNT (2 vol %) composite. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48162.     

Microcellular Conductive Carbon Black or Graphene/PVDF Composite Foam with 3D Conductive Channel: A Promising Lightweight,Heat-Insulating,and EMI-Shielding Material

In this study, a lightweight microcellular carbon-based filler/poly(vinylidene fluoride) (PVDF) composite foam is fabricated with a 3D conductive network that is thermally insulating, electrically conductive, and fabricated on a large scale. This composite can be used for high-efficiency thermal insulation and electromagnetic interference (EMI) shielding applications. The prepared composite demonstrates low density, high electrical conductivity, and excellent thermal insulation properties. The structure and density of the conductive network and the carbon-based filler content has a significant influence on the electrical conductivity of the prepared composite foam. Although the composite comprises microcellular PVDF beads of the same density, the conductivity of the composite-comprising strip beads is greater than that comprising spherical beads. In the same conductive network structure, as the size of the microcellular PVDF beads decrease, the conductive network becomes denser, which results in a higher conductivity. Furthermore, with an increase in the conductive filler content, the conductivity improves significantly. Excellent EMI shielding materials with optimal filler content and particle shapes, exhibiting EMI shielding effectiveness of up to 40–50 dB, are developed. The prepared composite foam possesses excellent application potential in the fields of ultra-light thermal insulation, conductivity, and EMI shielding.     

Hybrid composites of ABS with carbonaceous fillers for electromagnetic shielding applications

This work evaluates the influence of two types of carbonaceous fillers, carbon black (CB) and carbon nanotubes (CNTs), on the electrical, electromagnetic, and rheological properties of composites based on poly(acrylonitrile‐co‐butadiene‐co‐styrene) (ABS) prepared by the melt mixing. Electrical conductivity, electromagnetic shielding efficiency (EMI SE) in the X‐band frequency range (8–12.4 GHz), and melt flow index (MFI) results showed that ABS/CNT composites exhibit higher electrical conductivity and EMI SE, but lower MFI when compared to ABS/CB composites. The electrical conductivity of the binary composites showed an increase of around 16 orders of magnitude, when compared to neat ABS, for both fillers. Binary composites with 5 and 15 wt % of filler showed an EMI SE of, respectively, ?44 and ?83 dB for ABS/CNT, and ?9 and ?34 dB for ABS/CB. MFI for binary composites with 5 wt % were 15.45 and 0.55 g/10 min for CB and CNT, respectively. Hybrid composites ABS/CNT.CB with 3 wt % total filler and fraction 50:50 and 75:25 showed good correlation between EMI SE and MFI. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46546.     

Effects of carbon fiber modification with multiwall CNT on the electrical conductivity and EMI shielding effectiveness of polycarbonate/carbon fiber/CNT composites

The effect of carbon fiber (CF) modification with multiwall carbon nanotube (CNT) on the electrical, mechanical, and rheological properties of the polycarbonate (PC)/CF/CNT composite was investigated. The CF and multiwall CNT (MWCNT) were treated with sulfuric acid and nitric acid (3:1 wt %) mixture, to modify the CF with the CNT. For the PC with acid-treated CNT (a-CNT) modified acid-treated CF (a-CF) (PC/a-CF/a-CNT) composite, the electrical conductivity, and the electromagnetic interference shielding effectiveness (EMI SE) showed the highest values, compared with those of the PC/a-CF and PC/a-CF/CNT composites. The EMI SE of the PC/a-CF (10 wt %)/a-CNT (0.5 wt %) composite was found to be 26 (dB at the frequency of 10.0 GHz, and the EMI SE was increased by 91.2%, compared to that of the PC/a-CF composite at the same amount of total filler content. Among the composites studied in this work, the PC/a-CF/a-CNT composite also showed the highest values of relative permittivity (ε_r) and dielectric loss factor. The above results suggest that the CF modification with the a-CNT significantly affected the electrical conductivity and EMI SE of the composite, and the hybrid fillers of the a-CNT and a-CF resulted in good electrical pathways in the PC/a-CF/a-CNT composite. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47302.     

Electrically conductive polystyrene nanocomposites incorporated with aspect ratio-controlled silver nanowires

Polymer nanocomposites consisting of electrically conductive nanofillers with high aspect ratios are widely utilized for high-performance applications such as sensors and electronics. Silver nanowires (AgNWs) synthesized through polyol reduction have been reported to show excellent electrical conductivity, hydrophilicity, and high aspect ratios. In this study, the influence of the aspect ratios of the AgNWs on the rheological and electrical properties of the fabricated polystyrene (PS)/AgNW nanocomposites was chiefly investigated. The nanocomposites were made by combining a dispersion of AgNWs with a suspension of PS particles, followed by freeze-drying the PS/AgNW mixture harnessing the latex technology. Scanning electron microscopy, UV–Vis spectroscopy, and thermogravimetric analysis were performed on the nanocomposites to investigate the morphological, optical, and thermal properties, respectively; in addition, X-ray photoelectron spectroscopy was performed to examine the hydrophilic polymer poly(vinylpyrrolidone)-capped AgNW surfaces. The rheological behavior of the nanocomposites changed from liquid-like to solid-like after the addition of AgNWs with high aspect ratios. The electrical percolation threshold of the AgNWs in the nanocomposites was determined by the aspect ratio of the nanofiller rather than by its length. Thus, the various properties of the PS/AgNW nanocomposites could be tuned by tailoring the aspect ratios of the AgNWs. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47927.     

Effect of carbon nanotubes decorated with silver nanoparticles as hybrid filler on properties of natural rubber nanocomposites

Decoration of carbon nanotube (CNT) surfaces with silver nanoparticles (AgNPs) was performed using N,N-dimethylformamide reducing agent. The CNT-decorated with AgNP (CNT-AgNP) was then used to prepare natural rubber (NR) nanocomposites via latex mixing method. Cure characteristics, mechano-thermal relaxation, electrical conductivity, and thermal properties of the composites were investigated. It was found that the CNT-AgNP gave cure properties improved over plain NR compounds in terms of scorch time, degree of vulcanization, and activation energy. In addition, temperature scanning stress relaxation measurement revealed stronger network formation after incorporation of AgNP into the NR matrix due to the interaction among CNT and AgNP particles. This also provided high conductivity and low percolation threshold concentration for the CNT-AgNP filled NR, relative to plain CNT filled NR composites. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47281.     

Electrical and mechanical properties of multi‐walled carbon nanotubes reinforced PMMA and PS composites

The use of multi‐walled carbon nanotubes (MWCNT) as reinforcing material for thermoplastic polymer matrices, polymethyl methacrylate (PMMA), and polystyrene (PS) has been studied. MWCNT were synthesized by chemical vapor deposition (CVD) technique using ferrocene‐toluene mixture. As‐prepared nanotubes were ultrasonically dispersed in toluene and subsequently dispersed in PMMA and PS. Thin polymer composite films were fabricated by solvent casting. The effect of nanotube content on the electrical and mechanical properties of the nanocomposites was investigated. An improvement in electrical conductivity from insulating to conducting with increasing MWCNT content was observed. The carbon nanotube network showed a classical percolating network behavior with a low percolation threshold. Electromagnetic interference (EMI) shielding effectiveness value of about 18 dB was obtained in the frequency range 8.0–12 GHz (X‐band), for a 10 vol% CNT loading. An improved composite fabrication process using casting followed by compression molding and use of functionalized MWCNT resulted in increased composites strength. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Effects of filler geometry on internal structure and physical properties of polycarbonate composites prepared with various carbon fillers

BACKGROUND: The effects of filler geometry are important for understanding the internal structure and physical properties of polymer composites. To investigate the effects of filler geometry on electrical conductivity as well as morphological and rheological properties, three types of polycarbonate (PC) composites were prepared by melt compounding with a twin‐screw extruder. RESULTS: The electrical conductivity of PC/carbon black (CB) and PC/graphite (carbon) nanofibre (CNF) composites did not show a percolation threshold through the entire filler loading ranges. However, PC‐blend‐carbon nanotube (CNT) composites showed a percolation electrical threshold for a filler loading of 1.0 to 3.0 wt% and their maximum electrical conductivity approached 10^?3 S m^?1. PC‐blend‐CB and PC‐blend‐CNF composites showed Newtonian behaviour like pure PC matrix, but PC‐blend‐CNT composites showed yield stress as well as increased storage modulus and strong shear thinning behaviour at low angular frequency and shear rate due to strong interactions generated between CNT–CNT particles as well as PC molecules and CNT particles on the nanometre scale. CONCLUSIONS: The electrical conductivity of the PC composites with different carbon constituents was well explained by the continuous network structure formed between filler particles. The network structure was confirmed by the good dispersion of fillers as well as by the yield stress and solid‐like behaviour observed in steady and dynamic shear flows. Copyright © 2009 Society of Chemical Industry     

Modeling for the electromagnetic properties and EMI shielding of Cf/mullite composites in the gigahertz range

The electromagnetic properties and EMI shielding effectiveness of C_f/mullite composites via the spark plasma sintering were intensively investigated in the gigahertz range (8.2–12.4 GHz). Experimental results have revealed excellent electromagnetic properties and a high value of EMI shielding effectiveness (nearly 40 dB) for C_f/mullite composites with 1.65 vol% carbon fillers at thickness of 2 mm. We quantitatively characterize the contributions of microstructural features to overall EMI shielding effectiveness using a micromechanics-based homogenization model. The EMI shielding effectiveness enhances with respect to the C_f volume concentration before the threshold. The increasing trend of EMI shielding effectiveness with respect to AC (alternating current) frequency can be attributed to enhanced conductivity at high gigahertz range. It is demonstrated that filler and frequency dependent interface effects are essential to obtain excellent electromagnetic properties of C_f/mullite composite. The present research can provide guidances for the design of ceramic-based composites applied in high-temperature EMI shielding devices.