60-GHz high power performance In/sub 0.35/Al/sub 0.65/As-In/sub 0-35/Ga/sub 0.65/As metamorphic HEMTs on GaAs

We report on a double-pulse doped, double recess In/sub 0.35/Al/sub 0.65/As-In/sub 0.35/Ga/sub 0.65/As metamorphic high electron mobility transistor (MHEMT) on GaAs substrate. This 0.15-/spl mu/m gate MHEMT exhibits excellent de characteristics, high current density of 750 mA/mm, extrinsic transconductance of 700 mS/mm. The on and off state breakdown are respectively of 5 and 13 V and defined It gate current density of 1 mA/mm. Power measurements at 60 GHz were performed on these devices. Biased between 2 and 5 V, they demonstrated a maximum output power of 390 mW/mm at 3.1 V of drain voltage with 2.8 dB power gain and a power added efficiency (PAE) of 18%. The output power at 1 dB gain compression is still of 300 mW/mm. Moreover, the linear power gain is of 5.2 dB. This is to our knowledge the best output power density of any MHEMT reported at this frequency.     

Characteristics of In/sub 0.425/Al/sub 0.575/As-InxGa/sub 1-x/As metamorphic HEMTs with pseudomorphic and symmetrically graded channels

In/sub 0.425/Al/sub 0.575/As-In/sub x/Ga/sub 1-x/As metamorphic high electron mobility transistors (MHEMTs) with two different channel designs, grown by molecular beam epitaxy (MBE) system, have been successfully investigated. Comprehensive dc and high-frequency characteristics, including the extrinsic transconductance, current driving capability, device linearity, pinch-off property, gate-voltage swing, breakdown performance, unity-gain cutoff frequency, max. oscillation frequency, output power, and power gain, etc., have been characterized and compared. In addition, complete parametric information of the small-signal device model has also been extracted and discussed for the pseudomorphic channel MHEMT (PC-MHEMT) and the V-shaped symmetrically graded channel MHEMT (SGC-MHEMT), respectively.     

Turn-on voltage investigation of GaAs-based bipolar transistors with Ga/sub 1-x/In/sub x/As/sub 1-y/N/sub y/ base layers

The fundamental lower limit on the turn on voltage of GaAs-based bipolar transistors is first established, then reduced with the use of a novel low energy-gap base material, Ga/sub 1-x/In/sub x/As/sub 1-y/N/sub y/. InGaP/GaInAsN DHBTs (x/spl sim/3y/spl sim/0.01) with high p-type doping levels (/spl sim/3/spl times/10/sup 19/ cm/sup -3/) and dc current gain (/spl beta//sub max//spl sim/68 at 234 /spl Omega///spl square/) are demonstrated. A reduction in the turn-on voltage over a wide range of practical base sheet resistance values (100 to 400 /spl Omega///spl square/) is established relative to both GaAs BJTs and conventional InGaP/GaAs HBTs with optimized base-emitter interfaces-over 25 mV in heavily doped, high dc current gain samples. The potential to engineer turn-on voltages comparable to Si- or InP-based bipolar devices on a GaAs platform is enabled by the use of lattice matched Ga/sub 1-x/In/sub x/As/sub 1-y/N/sub y/ alloys, which can simultaneously reduce the energy-gap and balance the lattice constant of the base layer when x/spl sim/3y.     

High-temperature thermal stability performance in /spl delta/-doped In/sub 0.425/Al/sub 0.575/As--In/sub 0.65/Ga/sub 0.35/As metamorphic HEMT

We report, to our knowledge, the best high-temperature characteristics and thermal stability of a novel /spl delta/-doped In/sub 0.425/Al/sub 0.575/As--In/sub 0.65/Ga/sub 0.35/As--GaAs metamorphic high-electron mobility transistor. High-temperature device characteristics, including extrinsic transconductance (g/sub m/), drain saturation current density (I/sub DSS/), on/off-state breakdown voltages (BV/sub on//BV/sub GD/), turn-on voltage (V/sub on/), and the gate-voltage swing have been extensively investigated for the gate dimensions of 0.65/spl times/200 /spl mu/m/sup 2/. The cutoff frequency (f/sub T/) and maximum oscillation frequency (f/sub max/), at 300 K, are 55.4 and 77.5 GHz at V/sub DS/=2 V, respectively. Moreover, the distinguished positive thermal threshold coefficient (/spl part/V/sub th///spl part/T) is superiorly as low as to 0.45 mV/K.     

Performance improvement in tensile-strained In/sub 0.5/Al/sub 0.5/As/In/sub x/Ga/sub 1-x/As/In/sub 0.5/Al/sub 0.5/As metamorphic HEMT

This paper proposes a In/sub 0.5/Al/sub 0.5/As/In/sub x/Ga/sub 1-x/As/In/sub 0.5/Al/sub 0.5/As (x=0.3-0.5-0.3) metamorphic high-electron mobility transistor with tensile-strained channel. The tensile-strained channel structure exhibits significant improvements in dc and RF characteristics, including extrinsic transconductance, current driving capability, thermal stability, unity-gain cutoff frequency, maximum oscillation frequency, output power, power gain, and power added efficiency.     

DC and RF characteristics of E-mode Ga/sub 0.51/In/sub 0.49/P-In/sub 0.15/Ga/sub 0.85/As pseudomorphic HEMTs

The DC and RF characteristics of Ga/sub 0.49/In/sub 0.51/P-In/sub 0.15/Ga/sub 0.85/As enhancement- mode pseudomorphic HEMTs (pHEMTs) are reported for the first time. The transistor has a gate length of 0.8 /spl mu/m and a gate width of 200 /spl mu/m. It is found that the device can be operated with gate voltage up to 1.6 V, which corresponds to a high drain-source current (I/sub DS/) of 340 mA/mm when the drain-source voltage (V/sub DS/) is 4.0 V. The measured maximum transconductance, current gain cut-off frequency, and maximum oscillation frequency are 255.2 mS/mm, 20.6 GHz, and 40 GHz, respectively. When this device is operated at 1.9 GHz under class-AB bias condition, a 14.7-dBm (148.6 mW/mm) saturated power with a power-added efficiency of 50% is achieved when the drain voltage is 3.5 V. The measured F/sub min/ is 0.74 dB under I/sub DS/=15 mA and V/sub DS/=2 V.     

Highly linear Al/sub 0.3/Ga/sub 0.7/N-Al/sub 0.05/Ga/sub 0.95/N-GaN composite-channel HEMTs

We report an Al/sub 0.3/Ga/sub 0.7/N-Al/sub 0.05/Ga/sub 0.95/N-GaN composite-channel HEMT with enhanced linearity. By engineering the channel region, i.e., inserting a 6-nm-thick AlGaN layer with 5% Al composition in the channel region, a composite-channel HEMT was demonstrated. Transconductance and cutoff frequencies of a 1 /spl times/100 /spl mu/m HEMT are kept near their peak values throughout the low- and high-current operating levels, a desirable feature for linear power amplifiers. The composite-channel HEMT exhibits a peak transconductance of 150 mS/mm, a peak current gain cutoff frequency (f/sub T/) of 12 GHz and a peak power gain cutoff frequency (f/sub max/) of 30 GHz. For devices grown on sapphire substrate, maximum power density of 3.38 W/mm, power-added efficiency of 45% are obtained at 2 GHz. The output third-order intercept point (OIP3) is 33.2 dBm from two-tone measurement at 2 GHz.     

547-GHz f/sub t/ In/sub 0.7/Ga/sub 0.3/As-In/sub 0.52/Al/sub 0.48/As HEMTs with reduced source and drain resistance

We fabricated 30-nm gate pseudomorphic channel In/sub 0.7/Ga/sub 0.3/As-In/sub 0.52/Al/sub 0.48/As high electron mobility transistors (HEMTs) with reduced source and drain parasitic resistances. A multilayer cap structure consisting of Si highly doped n/sup +/-InGaAs and n/sup +/-InP layers was used to reduce these resistances while enabling reproducible 30-nm gate process. The HEMTs also had a laterally scaled gate-recess that effectively enhanced electron velocity, and an adequately long gate-channel distance of 12nm to suppress gate leakage current. The transconductance (g/sub m/) reached 1.5 S/mm, and the off-state breakdown voltage (BV/sub gd/) defined at a gate current of -1 mA/mm was -3.0 V. An extremely high current gain cutoff frequency (f/sub t/) of 547 GHz and a simultaneous maximum oscillation frequency (f/sub max/) of 400 GHz were achieved: the best performance yet reported for any transistor.     

A novel InGaP/Al/sub x/Ga/sub 1-x/As/GaAs CEHBT

A new and interesting InGaP/Al/sub x/Ga/sub 1-x/As/GaAs composite-emitter heterojunction bipolar transistor (CEHBT) is fabricated and studied. Based on the insertion of a compositionally linear graded Al/sub x/Ga/sub 1-x/As layer, a near-continuous conduction band structure between the InGaP emitter and the GaAs base is developed. Simulation results reveal that a potential spike at the emitter/base heterointerface is completely eliminated. Experimental results show that the CEHBT exhibits good dc performances with dc current gain of 280 and greater than unity at collector current densities of J/sub C/=21kA/cm/sup 2/ and 2.70/spl times/10/sup -5/ A/cm/sup 2/, respectively. A small collector/emitter offset voltage /spl Delta/V/sub CE/ of 80 meV is also obtained. The studied CEHBT exhibits transistor action under an extremely low collector current density (2.7/spl times/10/sup -5/ A/cm/sup 2/) and useful current gains over nine decades of magnitude of collector current density. In microwave characteristics, the unity current gain cutoff frequency f/sub T/=43.2GHz and the maximum oscillation frequency f/sub max/=35.1GHz are achieved for a 3/spl times/20 /spl mu/m/sup 2/ device. Consequently, the studied device shows promise for low supply voltage and low-power circuit applications.     

Influences of /spl delta/-doping position on the characteristics of SiGe-Si DCFETs

SiGe-Si doped channel field-effect-transistors with different positions of /spl delta/ layers in SiGe wells have been proposed and fabricated. High forward gate to drain turn-on voltage (>0.87 V) and reverse breakdown voltage up to 25 V was obtained for center and bottom /spl delta/-doped channel devices. For device structures with the same 1/spl times/100 /spl mu/m/sup 2/ gate, center /spl delta/-doped channel device display the best dc maximum extrinsic transconductance of 22.1 mS/mm. Compared with conventional Si-SiGe MODFETs, center /spl delta/-doped channel device exhibits improved gate voltage swings as wide as 3 V due to the better carrier confinement and the absence of parallel conduction, which is promising to provide an additional degree of freedom for Si-based device applications.     

Broadband microwave noise characteristics of high-linearity composite-channel Al/sub 0.3/Ga/sub 0.7/N/Al/sub 0.05/Ga/sub 0.95/N/GaN HEMTs

We report broadband microwave noise characteristics of a high-linearity composite-channel HEMT (CC-HEMT). Owing to the novel composite-channel design, the CC-HEMT exhibits high gain and high linearity such as an output third-order intercept point (OIP3) of 33.2 dBm at 2 GHz. The CC-HEMT also exhibits excellent microwave noise performance. For 1-/spl mu/m gate-length devices, a minimum noise figure (NF/sub min/) of 0.7 dB and an associated gain (G/sub a/) of 19 dB were observed at 1 GHz, and an (NF/sub mi/) of 3.3 dB and a G/sub a/ of 10.8 dB were observed at 10 GHz. The dependence of the noise characteristics on the physical design parameters, such as the gate-source and gate-drain spacing, is also presented.     

High transconductance of 2.25 S/mm observed at 16 K for 195-nm-gate In/sub 0.75/Ga/sub 0.25/As/In/sub 0.52/Al/sub 0.48/As HEMT fabricated on [411]A-oriented InP substrate

We achieved a maximum transconductance (g/sub m/) of 2.25 S/mm at 16 K for a 195-nm-gate In/sub 0.75/Ga/sub 0.25/As/In/sub 0.52/Al/sub 0.48/As pseudomorphic high-electron mobility transistor (PHEMT) fabricated on a [411]A-oriented InP substrate, which is the highest value ever reported for HEMTs. This PHEMT also showed a much enhanced cutoff frequency (f/sub T/) of 310 GHz at 16 K, compared with its room temperature value (245 GHz). The significantly enhanced g/sub m/ and f/sub T/ at 16 K can be attributed to the higher saturation velocity in the region "under the gate," which is caused not only by suppressing the phonon scattering, but also by suppressing the interface roughness scattering due to the "(411)A super-flat InGaAs/InAlAs interfaces" (effectively atomically flat heterointerfaces over a wafer-size area).     

High-performance 0.1-/spl mu/m In/sub 0.4/AlAs/In/sub 0.35/GaAs MHEMTs with Ar plasma treatment

High-performance 0.1-/spl mu/m In/sub 0.4/AlAs/In/sub 0.35/GaAs metamorphic high-electron mobility transistors (MHEMTs) on GaAs substrate have been successfully fabricated with Ar plasma treatment. Before the gate Schottky metallization, the devices were treated with Ar plasma, which might clean and improve the surface of exposed barrier layer. The devices fabricated with Ar plasma treatment exhibited the excellent characteristics such as 50% reduction of the reverse gate leakage currents, the improved Schottky ideality factor of 1.37, high extrinsic transconductance of 700 mS/mm, and high maximum drain current density of 780 mA/mm. And the cutoff frequency f/sub T/ as high as 210 GHz was achieved. To our knowledge, this is the best reported cutoff frequency for a 0.1-/spl mu/m MHEMT with an indium content of 35% in the channel.     

Impacts of gate electrode materials on threshold voltage (V/sub th/) instability in nMOS HfO/sub 2/ gate stacks under DC and AC stressing

Ultrathin nMOSFET hafnium oxide (HfO/sub 2/) gate stacks with TiN metal gate and poly-Si gate electrodes are compared to study the impact of the gate electrode on long term threshold instability reliability for both dc and ac stress conditions. The poly-Si/high-/spl kappa/ interface exhibits more traps due to interfacial reaction than the TiN/high-/spl kappa/ interface, resulting in significantly worse dc V/sub th/ instability. However, the V/sub th/ instability difference between these two stacks decreases and eventually diminishes as ac stress frequency increases, which suggests the top interface plays a minor role in charge trapping at high operating frequency. In addition, ac stress induced interface states (Nit) can be effectively recovered, resulting in negligible G/sub m/ degradation.     

High breakdown voltage (Al/sub 0.3/Ga/sub 0.7/)/sub 0.5/In/sub 0.5/P/InGaAs quasi-enhancement-mode pHEMT with field-plate technology

A high breakdown voltage and a high turn-on voltage (Al/sub 0.3/Ga/sub 0.7/)/sub 0.5/In/sub 0.5/P/InGaAs quasi-enhancement-mode (E-mode) pseudomorphic HEMT (pHEMTs) with field-plate (FP) process is reported for the first time. Between gate and drain terminal, the transistor has a FP metal of 1 /spl mu/m, which is connected to a source terminal. The fabricated 0.5/spl times/150 /spl mu/m/sup 2/ device can be operated with gate voltage up to 1.6 V owing to its high Schottky turn-on voltage (V/sub ON/=0.85 V), which corresponds to a high drain-to-source current (I/sub ds/) of 420 mA/mm when drain-to-source voltage (V/sub ds/) is 3.5 V. By adopting the FP technology and large barrier height (Al/sub 0.3/Ga/sub 0.7/)/sub 0.5/In/sub 0.5/P layer design, the device achieved a high breakdown voltage of -47 V. The measured maximum transconductance, current gain cutoff frequency and maximum oscillation frequency are 370 mS/mm, 22 GHz , and 85 GHz, respectively. Under 5.2-GHz operation, a 15.2 dBm (220 mW/mm) and a 17.8 dBm (405 mW/mm) saturated output power can be achieved when drain voltage are 3.5 and 20 V. These characteristics demonstrate that the field-plated (Al/sub 0.3/Ga/sub 0.7/)/sub 0.5/In/sub 0.5/P E-mode pHEMTs have great potential for microwave power device applications.     

Al/sub 0.3/Ga/sub 0.7/As/In/sub x/Ga/sub 1-x/As (0/spl les/x/spl les/0.25) doped-channel field-effect transistors (DCFET's)

The properties of both lattice-matched and strained doped-channel field-effect transistors (DCFET's) have been investigated in AlGaAs/In/sub x/Ga/sub 1-x/As (0/spl les/x/spl les/0.25) heterostructures with various indium mole fractions. Through electrical characterization of grown layers in conjunction with the dc and microwave device characteristics, we observed that the introduction of a 150-/spl Aring/ thick strained In/sub 0.15/Ga/sub 0.85/As channel can enhance device performance, compared to the lattice-matched one. However, a degradation of device performance was observed for larger indium mole fractions, up to x=0.25, which is associated with strain relaxation in this highly strained channel. DCFET's also preserved a more reliable performance after biased-stress testings.<>     

High-performance In/sub 0.53/Ga/sub 0.47/As thermophotovoltaic devices grown by solid source molecular beam epitaxy

In/sub 0.53/Ga/sub 0.47/As-based monolithic interconnected modules (MIMs) of thermophotovoltaic (TPV) devices lattice-matched to InP were grown by solid source molecular beam epitaxy. The MIM device consisted of ten individual In/sub 0.53/Ga/sub 0.47/As TPV cells connected in series on an InP substrate. An open-circuit voltage (V/sub oc/) of 4.82 V, short-circuit current density (J/sub sc/) of 1.03 A/cm/sup 2/ and fill factor of /spl sim/73% were achieved for a ten-junction MIM with a bandgap of 0.74 eV under high intensity white light illumination. Device performance uniformity was better than 1.5% across a full 2-in InP wafer. The V/sub oc/ and J/sub sc/ values are the highest yet reported for 0.74-eV band gap n-p-n MIM devices.     

RF, DC, and reliability characteristics of ALD HfO/sub 2/-Al/sub 2/O/sub 3/ laminate MIM capacitors for Si RF IC applications

High-performance metal-insulator-metal capacitors using atomic layer-deposited HfO/sub 2/-Al/sub 2/O/sub 3/ laminate are fabricated and characterized for RF and mixed-signal applications. The laminate capacitor can offer high capacitance density (12.8 fF//spl mu/m/sup 2/) up to 20 GHz, low leakage current of 4.9/spl times/10/sup -8/ A/cm/sup 2/ at 2 V and 125/spl deg/C, and small linear voltage coefficient of capacitance of 211 ppm/V at 1 MHz, which can easily satisfy RF capacitor requirements for year 2007 according to the International Technology Roadmap for Semiconductors. In addition, effects of constant voltage stress and temperature on leakage current and voltage linearity are comprehensively investigated, and dependences of quadratic voltage coefficient of capacitance (/spl alpha/) on frequency and thickness are also demonstrated. Meanwhile, the underlying mechanisms are also discussed.     

AlGaN/GaN HEMTs on SiC with f/sub T/ of over 120 GHz

AlGaN/GaN high electron mobility transistors (HEMTs) grown on semi-insulating SiC substrates with a 0.12 /spl mu/m gate length have been fabricated. These 0.12-/spl mu/m gate-length devices exhibited maximum drain current density as high as 1.23 A/mm and peak extrinsic transconductance of 314 mS/mm. The threshold voltage was -5.2 V. A unity current gain cutoff frequency (f/sub T/) of 121 GHz and maximum frequency of oscillation (f/sub max/) of 162 GHz were measured on these devices. These f/sub T/ and f/sub max/ values are the highest ever reported values for GaN-based HEMTs.     

Limitation of DC currents by YBa/sub 2/Cu/sub 3/O/sub 7-/spl delta//-Au superconducting films

The limitation of dc fault currents is one of the issues for the development of dc networks or links. This paper shows for the first time the high potential of YBa/sub 2/Cu/sub 3/O/sub 7-/spl delta//-Au bilayers for the design of dc current limiters. Such devices are based on the transition into the normal state of the superconducting YBa/sub 2/Cu/sub 3/O/sub 7-/spl delta// films above a current I/sup */>I/sub c/, where I/sub c/ is the critical current at the onset of dissipation. The study of the transition under current pulses shows that a thermally driven transition into the normal state can occur after a delay t/sub trans/. This duration is defined by the amplitude of the current pulse. For I/sup *//spl ap/3I/sub c/, this delay is less than 10 /spl mu/s. The abrupt transition into the normal state allows an efficient current limitation. A recovery of the superconducting state can also occur under current. This property can be extremely interesting for autonomous operation of a current limiter in an electrical network in case of transient over-currents coming from the starting of high-power devices.