Structure Evolution from Pb(Mg1/3Nb2/3)O3 to La(Mg2/3Nb1/3)O3

The crystal structure of lanthanum-modified lead magnesium niobates having composition (Pb_{1− x} La _x ) (Mg_{(1+ x )/3}-Nb_{(2− x )/3})O₃ with X = 0 to 1 was investigated by X-ray powder diffraction. It was found that the fundamental reflections from perovskite structure remain in the whole range of composition. The superlattice reflections from the A(B'_1/2-B"_1/2)O₃ ordered structure are also well preserved for La content greater than 50 at.%; however, a series of extra peaks of mixing indices appears, with intensities gradually enhanced with the increase of La content. For the complete substitution of Pb by La, a splitting of some reflections can be observed in the diffraction pattern. The results indicate that the crystal structure evolves continuously with the La content, from disordered cubic perovskite of space group Pm 3 m for X = 0, to ordered cubic perovskite of space group Fm 3 m for X = 0.5, distorted cubic perovskite of space group Pa 3 for 0.5 < X < 0.9, and finally to a rhombohedral perovskite, possibly belonging to the space group R 3 , for X ≥ 0.9. In the evolution of structure, a linear reduction of the lattice constant of the perovskite cell from 4.048 to 3.964 Å was observed.     

Cation Ordering Transformations in the Ba(Zn1/3Nb2/3)O3-La(Zn2/3Nb1/3)O3 System

Single-phase perovskites were formed in the (1−_x)Ba(Zn_1/3Nb_2/3)O₃-( _x )La(Zn_2/3Nb_1/3)O₃ system for compositions with 0.0≤ x ≤0.6. Although the stability of the trigonal "1:2" ordered structure of the Ba(Zn_1/3Nb_2/3)O₃ end member is very limited (0.0≤ x ≤0.05), low levels of lanthanum induce a transformation to a cubic, "1:1" ordered structure that has a broad range of homogeneity (0.05≤ x ≤0.6). Samples with x > 0.6 were comprised of La₃NbO₇, ZnO, and a perovskite with x = 0.6. The cubic 1:1 phases were fully ordered and no evidence was found for a compositionally segregated microstructure. These observations could not be reconciled in terms of a "space-charge" model; rather, they supported a charge-balanced, "random-site" structure for the 1:1 cation-ordered Ba(β_1/2'β_1/2")O₃ phases.     

Single-Calcination Synthesis of Pyrochlore-Free 0.9Pb(Mg1/3Nb2/3)O3–0.1PbTiO3 and Pb(Mg1/3Nb2/3)O3 Ceramics Using a Coating Method

A coating approach for synthesizing 0.9Pb(Mg_1/3Nb_2/3)O₃–0.1PbTiO₃ (0.9PMN–0.1PT) and PMN using a single calcination step was demonstrated. The pyrochlore phase was prevented by coating Mg(OH)₂ on Nb₂O₅ particles. Coating of Mg(OH)₂ on Nb₂O₅ was done by precipitating Mg(OH)₂ in an aqueous Nb₂O₅ suspension at pH 10. The coating was confirmed using optical micrographs and zeta-potential measurements. A single calcination treatment of the Mg(OH)₂-coated Nb₂O₅ particles mixed with appropriate amounts of PbO and PbTiO₃ powders at 900°C for 2 h produced pyrochlore-free perovskite 0.9PMN–0.1PT and PMN powders. The elimination of the pyrochlore phase was attributed to the separation of PbO and Nb₂O₅ by the Mg(OH)₂ coating. The Mg(OH)₂ coating on the Nb₂O₅ improved the mixing of Mg(OH)₂ and Nb₂O₅ and decreased the temperature for complete columbite conversion to ∼850°C. The pyrochlore-free perovskite 0.9PMN–0.1PT powders were sintered to 97% density at 1150°C. The sintered 0.9PMN–0.1PT ceramics exhibited a dielectric constant maximum of ∼24 660 at 45°C at a frequency of 1 kHz.     

Dielectric and Electrostrictive Properties of Ferroelectric Relaxors in the System Pb(Mg1/3Nb2/3)O3:PbTiO3: Ba(Zn1/3Nb2/3)O3

Ceramic dielectrics which have been fabricated in the Pb(Mg_1/3 Nb_2/3)O₃:PbTiO₃:Ba(Zn_1/3Nb_2/3)O₃ composition system are shown to exhibit two distinct dielectric maxima, both of which show the characteristic loss spectra of ferroelectrics with diffuse phase transitions. The height of the individual maxima can be controlled by the Zn:Mg ratio in the starting material and, in suitably chosen compositions, a wide range of almost temperature-independent high dielectric permittivity is possible. These dielectrics show strong electrostrictive deformations under high electric fields but the electrostrictive strain is much less temperature-sensitive than in other relaxors.     

Mechanochemical Synthesis of 0.9[0.6Pb(Zn1/3Nb2/3)O3·0.4Pb(Mg1/3Nb2/3)O3]·0.1PbTiO3

Lead zinc niobate–lead magnesium niobate–lead titanate (PZN–PMN–PT) ceramic powders of perovskite structure have been prepared via a mechanochemical processing route. A single-phase perovskite powder of ultrafine particles in the nanometer range was successfully synthesized when a MZN powder (columbite precursor) was mechanically activated for 10 h together with mixed lead and titanium oxides. The following steps are involved when the ternary oxide mixture is subjected to an increasing degree of mechanical activation. First, the starting materials are significantly refined in particle size as a result of the continuous deformation, fragmentation and then partially amorphized at the initial stage of mechanical activation. This is followed by the formation of perovskite nuclei and subsequent growth of these nuclei in the activated oxide matrix with increasing activation time. When calcined at various temperatures in the range of 500–800°C, pyrochlore phase was not detected by XRD phase analysis in the mechanochemically synthesized powder. Only a minor amount (∼2%) of pyrochlore phase was observed when the calcination temperature was raised to 850°C. The PZN–PMN–PT derived from the mechanochemically synthesized powder can be sintered to ∼98% relative density at a sintering temperature of 950°C. The PZN–PMN–PT sintered at 1100°C for 1 h exhibits a dielectric constant of ∼18 600 and a dielectric loss of 0.015 at the Curie temperature of 112°C when measured at a frequency of 0.1 kHz, together with a d ₃₃ value of 323 ×10⁻¹² pC/N.     

Phase Transition and Ferroelectric Characteristics of Pb[(Mg1/3Nb2/3)1-xTix]O3 Ceramics Modified with La(Mg2/3Nb1/3)O3

The effects of 0–5 mol% addition of La(Mg_2/3Nb_1/3)O₃ (LMN) on the phase transition and ferroelectric behaviors of Pb[(Mg_1/3Nb_2/3)_1-xTi_x]O₃ (PMNT) ceramics with compositions near the morphotropic phase boundary (MPB) were studied. An evolution of structure from rhombohedral to tetragonal was found with increasing PbTiO₃ (PT) content across the MPB (at ∼32.5 mol% PT), and a coexistence of both rhombohedral and tetragonal phases was also found at the MPB. The dual-phase field extended toward the lower PT content side of the MPB, and, moreover, the rhombohedrality or tetragonality was reduced, especially for the compositions near the MPB, by the addition of La in PMNT. The ferroelectric transition was found to change from normal to diffuse as the La content increased and the compositions became more rhombohedral. In accordance with the structural evolution, the change of remanent polarization ( P _r) and coercive field ( E _c) also became gradually indistinct, and both P _r and E _c were reduced. For compositions near the MPB, both PMNT and La-modified PMNT had a similar electromechanical factor ( k _p) in a range around 0.55–0.60, but the mechanical quality factor ( Q _m) was significantly reduced for the La-modified PMNT. The piezoelectric coefficient ( d ₃₃), however, was largely improved with increasing La content in PMNT of compositions at MPB. A high value of d ₃₃∼ 815 pC/N was obtained for the 5-mol%-La-modified ceramics, but it was associated with a low value of Q _m.     

Order-Disorder Phase Formation in the Complex Perovskite Compounds Ba(Ni1/3Nb2/3)O3 and Ba(Zn1/3Nb2/3)O3

The order-disorder phase formation of the complex perovskite compounds Ba(Ni_1/3Nb_2/3)O₃ (BNN) and Ba(Zn_1/3-Nb_2/3)O₃ (BZN) was investigated using X-ray diffraction, transmission electron microscopy, scanning electron microscopy, and energy-dispersive spectroscopy. The BNN and BZN samples were sintered over a temperature range of 1200° to 1500°C in air for 2 h. X-ray diffraction and transmission electron microscopy showed that these compounds exhibited a 1:2 ordering on the B-site within a narrow temperature range. When BNN and BZN were sintered above 1400° and 1350°C, respectively, a liquid phase formed in the grain boundary which was accompanied by disordering. The composition of the liquid phase resembled that of pyrochlore, with a small amount of nickel for BNN or zinc for BZN. The disordering with the formation of the liquid phase was attributed to the increase in defect concentration.     

Dielectric Characteristics of Bi- and Ti-Substituted Pb(Mg1/3Nb2/3)O3

Pb[Mg_1/3Nb_2/3]O₃ was gradually substituted by Bi[Mg_2/3Nb_1/3]O₃ (BiMN) up to 30 mol%, with an overall modification by a constant fraction of PbTiO₃ (10 mol%). Monophasic perovskite powders could be prepared via the B-site precursor route. Ceramic samples of the system showed a typical relaxor behavior of frequency-dependent dielectric dispersion. Values of the maximum dielectric constant decreased substantially with increasing BiMN concentration, whereas corresponding temperatures changed only moderately.     

Structure and Dielectric Properties of the Ba(Mg1/3Nb2/3)O3-La(Mg2/3Nb1/3)O3 System

A complete range of perovskite solid solutions can be formed in the (1 − x )Ba(Mg_1/3Nb_2/3)O₃- x La(Mg_2/3Nb_1/3)O₃ (BMN-LMN) pseudobinary system. While pure BMN adopts a 1:2 cation ordered structure, 1:1 ordered phases are stabilized for 0.05 ≤ x ≤ 1.0. Dark-field TEM images indicate that the La-doped solid solutions are comprised of large 1:1 ordered domains and no evidence was found for a phase-separated structure. This observation coupled with the systematic variations in the intensities of the supercell reflections supports a charge-balanced "random-site" model for the 1:1 ordering. The substitution of La also induces a transformation from a negative to positive temperature coefficient of capacitance in the region 0.25 ≤ x ≤ 0.5.     

Processing and Electrical Properties in Lead-Based (Pb(Mg1/3Nb2/3)O3, Pb(Yb1/2Nb1/2)O3, PbTiO3) Systems

Lead-based ferroelectric (FE) ceramics exhibit superior electromechanical properties; therefore, there has been an increased focus on developing new lead-based FE materials with high Curie temperature ( T _c) and enhanced properties. The aim of this study was to investigate new compositions in the Pb(Mg_1/3Nb_2/3)O₃–Pb(Yb_1/2Nb_1/2)O₃–PbTiO₃ ( PMN–PYbN–PT) system to enhance the electromechanical properties while increasing the T _c and lowering the sintering temperature. The 0.575[0.5PMN–0.5PYbN]–0.425PT composition at PMN/PYbN (50/50) mole ratio were prepared by reactive sintering PMNT and PYbNT powder mixtures at 950°–1200°C for 4 h. PMNT and PYbNT powders were calcined via the columbite method. Samples were prepared by cold isostatic pressing at 80 MPa. Dense and fully perovskite 0.575[0.5PMN–0.5PYbN]–0.425PT ceramics were fabricated at 975°C for 4 h, and these samples displayed a remnant polarization ( P _r) of 32 μ C/cm², coercive field ( E _c) of 17 kV/cm, and a piezoelectric charge coefficient ( d ₃₃) of 475 pC/N. It is proposed that this ternary system can be tailored for various applications.     

Adhesive-Bonded Ca(Mg1/3Nb2/3)O3/Ba(Zn1/3Nb2/3)O3 Layered Dielectric Resonators with Tunable Temperature Coefficient of Resonant Frequency

Ca(Mg_1/3Nb_2/3)O₃ and Ba(Zn_1/3Nb_2/3)O₃ ceramic cylinders with the same diameter were bonded by adhesive with low dielectric loss to yield the layered dielectric resonators, and the microwave dielectric characteristics were evaluated with TE_01δ mode. With increasing the Ba(Zn_1/3Nb_2/3)O₃ thickness fraction, the resonant frequency ( f ₀) decreased, while the effective dielectric constant (ɛ _{r ,eff}) and temperature coefficient of resonant frequency (τ _f ) increased. Good microwave dielectric characteristics were attained for the samples with the Ba(Zn_1/3Nb_2/3)O₃ thickness fraction of 0.5: ɛ _{r ,eff}=34.33, Q × f =57 930 GHz and τ _f =2.6 ppm/°C. Finite-element method was used to predict the microwave dielectric characteristics of the layered resonators and good agreements were attained between the experimental results and predicted ones. Also, both experiment and finite-element analysis indicated that the effects of the adhesive on f ₀, ɛ _{r ,eff}, and τ _f were slight, while that on Q × f value was significant.     

Perovskite Phase Formation in the Relaxor System [Pb(Fe1/2Nb1/2)O3]1-x–[Pb(Zn1/3Nb2/3)O3]x

Phase formation and dielectric properties of the compositions in the system [Pb(Fe_1/2Nb_1/2)O₃]₁_ _x –[Pb(Zn_1/3Nb_2/3)O₃] _x were investigated as possible materials for multilayer ceramic capacitors. The formation of the phase with perovskite structure and dielectric properties of ceramics at room temperature in the entire composition range are presented. The undesirable pyrochlore phase can be suppressed up to x = 0.6 by adopting calcination of B-site oxides, followed by reaction with PbO. Compositions in the single-phase range can be sintered at less than 1000°C.     

Single-Calcination Synthesis of Pyrochlore Free Pb(Mg1/3Nb2/3)O3 Powders Using Particle-Coating Method

Using two-step particle-coating method, pyrochlore-free Pb(Mg_1/3Nb_2/3)O₃ (PMN) powders have been successfully synthesized by a single calcination step at a relatively lower calcined temperature of 850°C. The XRD and EDS results confirmed that the Mg–citric acid polymeric complex coatings effectively prevent direct contact between PbO and Nb₂O₅ and thus avoid the formation of pyrochlore phase. The coated powders were calcined directly without the ball-milling procedure at 850°C. The pyrochlore-free PMN powders obtained showed uniform and even grain size. The results showed that this method is an attractive method for the synthesis of PMN-based composite powders.     

B-Site Order–Disorder Transition in Pb(Mg1/3Nb2/3)O3–Pb(Mg1/2W1/2)O3 Triggered by Mechanical Activation

B-site cation order–disorder transition induced by mechanical activation was observed in Pb(Mg_1/3Nb_2/3)O₃–Pb(Mg_1/2W_1/2)O₃ (PMN–PMW) solid solution, which was examined using both XRD diffraction and Raman spectroscopic study. The order–disorder transition is composition dependent. Mechanical activation triggers the B-site disordering, which can be steadily recovered by thermal annealing at elevated temperature, i.e., at temperatures around 600°C. Raman spectroscopy demonstrated that there existed tiny ordered microdomains in 0.4PMN·0.6PMW subjected to up to 20 h of mechanical activation, although they cannot be shown by X-ray diffraction. This is a result of the equilibrium between the mechanical destruction and temperature-facilitated recovering at the collision points during mechanical activation. It is therefore unlikely that a complete disordering can be realized in PMN–PMW by mechanical activation. The disordering in PMN–PMW triggered by mechanical activation occurs simultaneously with the refinement in crystallite size at the initial stage of mechanical activation, suggesting that the fragmentation of crystallites is responsible for the order–disorder transition at least during the initial stage of mechanical activation.     

Spray Pyrolysis Synthesis and Dielectric Properties of Pb(Mg1/3Nb2/3)O3

Spray pyrolysis was used to synthesize lead magnesium niobate (PMN) by atomizing a mixture of nitrate aqueous solutions into a high-temperature furnace. This approach allows for instant removal of solvents and decomposition of metal–salts, thereby limiting phase segregation on a nanometer scale, and lowering the transformation temperature for pyrochlore-to-perovskite phase transition. As-synthesized particles were nanocrystalline pyrochlores, with an average crystallite size ∼22 nm. More than 96% perovskite phase was obtained when as-sprayed powders were subsequently calcined at 750°C for 4 h. Sintered PMN ceramics exhibited the typical frequency-dependent dielectric properties, with a peak value of dielectric constant of 18 000, and a transition temperature at −9.6°C at 100 Hz. A series of ceramics were prepared with varied grain sizes. Increasing the grain size increased the dielectric constant, probably due to the smaller fraction of the less-polarizable grain-boundary phases.     

Effects of Stacking Scheme on Microwave Dielectric Characteristics of Ca(Mg1/3Nb2/3)O3–Ba(Zn1/3Nb2/3)O3 Layered Dielectric Resonators

Ca(Mg_1/3Nb_2/3)O₃ (CMN) and Ba(Zn_1/3Nb_2/3)O₃ (BZN) ceramic disks were stacked with three stacking schemes, designated as CMN/BZN, CMN/BZN/CMN, and BZN/CMN/BZN, to yield layered dielectric resonators, and the microwave dielectric characteristics were evaluated with the TE_01δ mode. Both experiments and finite element analysis showed that the microwave dielectric characteristics of the layered resonator were determined not only by the volume fraction of BZN but also by the stacking scheme. For each stacking scheme, a good combination of microwave dielectric characteristics with an effective dielectric constant of 34.33–34.52, a Q × f value of 58 800–62 080 GHz, and a near-zero temperature coefficient of resonant frequency could be achieved by adjusting the volume fraction of BZN. The effects of the stacking scheme on the microwave dielectric characteristics of the temperature-stable layered resonator were discussed by combining finite element analysis and dielectric composite models.