A renewable pathway towards increased utilization of hydrogen in diesel engines

In the present work, dual fuel operation of a diesel engine has been experimentally investigated using biodiesel and hydrogen as the test fuels. Jatropha Curcas biodiesel is used as the pilot fuel, which is directly injected in the combustion chamber using conventional diesel injector. The main fuel (hydrogen) is injected in the intake manifold using a hydrogen injector and electronic control unit. In dual fuel mode, engine operations are studied at varying engine loads at the maximum pilot fuel substitution conditions. The engine performance parameters such as maximum pilot fuel substitution, brake thermal efficiency and brake specific energy consumption are investigated. On emission side, oxides of nitrogen, hydrocarbon, carbon monoxide and smoke emissions are analysed. Based on the results, it is found that biodiesel-hydrogen dual fuel engine could utilize up to 80.7% and 24.5% hydrogen (by energy share) at low and high loads respectively along with improved brake thermal efficiency. Furthermore, hydrocarbon, carbon monoxide and smoke emissions are significantly reduced compared to single fuel diesel engine operation. Exhaust gas recirculation (EGR) has also been studied with biodiesel-hydrogen dual fuel engine operations. It is found that EGR could improve the utilization of hydrogen in dual fuel engine, especially at the high loads. The effect of EGR is also found to reduce high nitrogen oxide emissions from the dual fuel engine and brake thermal efficiency is not significantly affected.     

Evaluating combustion,performance and emission characteristics of diesel engine using karanja oil methyl ester biodiesel blends enriched with HHO gas

With a specific end goal to take care of the worldwide demand for energy, a broad research is done to create alternative and cost effective fuel. The fundamental goal of this examination is to investigate the combustion, performance and emission characteristics of diesel engine using biodiesel blends enriched with HHO gas. The biodiesel blends are gotten by blending KOME obtained from transesterification of karanja oil in various proportions with neat diesel. The HHO gas is produced by the electrolysis of water in the presence of sodium bicarbonate electrolyte. The constant flow of HHO gas accompanied with biodiesel guarantees lessened brake specific fuel consumption by 2.41% at no load and 17.53% at full load with increased the brake thermal efficiency by 2.61% at no load and 21.67% at full load contrasted with neat diesel operation. Noteworthy decline in unburned hydrocarbon, carbon monoxide, carbon-dioxide emissions and particulate matter with the exception of NO_x discharge is encountered. The addition of EGR controls this hike in NO_x with a slight decline in the performance characteristics. It is clear that the addition of HHO gas with biodiesel blends along with EGR in the test engine improved the overall characterization of engine.     

A study on the performance and emission of a diesel engine fueled with Jatropha biodiesel oil and its blends

Biodiesel either in neat form or as a mixture with diesel fuel is widely investigated to solve the twin problem of depletion of fossil fuels and environmental degradation. The main objective of the present study is to compare performance, emission and combustion characteristics of biodiesel derived from non edible Jatropha oil in a dual fuel diesel engine with base line results of diesel fuel. The performance parameters evaluated were: brake thermal efficiency, brake specific fuel consumption, power output. As a part of combustion study, in-cylinder pressure, rate of pressure rise and heat release rates were evaluated. The emission parameters such as carbon monoxide, carbon dioxide, un-burnt hydrocarbon, oxides of nitrogen and smoke opacity with the different fuels were also measured and compared with base line results. The different properties of Jatropha oil after transestrification were within acceptable limits of standards as set by many countries. The brake thermal efficiency of Jatropha methyl ester and its blends with diesel were lower than diesel and brake specific energy consumption was found to be higher. However, HC, CO and CO₂ and smoke were found to be lower with Jatropha biodiesel fuel. NO_x emissions on Jatropha biodiesel and its blend were higher than Diesel. The results from the experiments suggest that biodiesel derived from non edible oil like Jatropha could be a good substitute to diesel fuel in diesel engine in the near future as far as decentralized energy production is concerned. In view of comparable engine performance and reduction in most of the engine emissions, it can be concluded and biodiesel derived from Jatropha and its blends could be used in a conventional diesel engine without any modification.     

Experimental investigations on combustion, performance and emissions characteristics of neat karanji biodiesel and its methanol blend in a diesel engine

The increased focus on alternative fuels research in the recent years are mainly driven by escalating crude oil prices, stringent emission norms and the concern on clean environment. The processed form of vegetable oil (biodiesel) has emerged as a potential substitute for diesel fuel on account of its renewable source and lesser emissions. The experimental work reported here has been carried out on a turbocharged, direct injection, multi-cylinder truck diesel engine fitted with mechanical distributor type fuel injection pump using biodiesel-methanol blend and neat karanji oil derived biodiesel under constant speed and varying load conditions without altering injection timings. The results of the experimental investigation indicate that the ignition delay for biodiesel-methanol blend is slightly higher as compared to neat biodiesel and the maximum increase is limited to 1 deg. CA. The maximum rate of pressure rise follow a trend of the ignition delay variations at these operating conditions. However, the peak cylinder pressure and peak energy release rate decreases for biodiesel-methanol blend. In general, a delayed start of combustion and lower combustion duration are observed for biodiesel-methanol blend compared to neat biodiesel fuel. A maximum thermal efficiency increase of 4.2% due to 10% methanol addition in the biodiesel is seen at 80% load and 16.67 s⁻¹ engine speed. The unburnt hydrocarbon and carbon monoxide emissions are slightly higher for the methanol blend compared to neat biodiesel at low load conditions whereas at higher load conditions unburnt hydrocarbon emissions are comparable for the two fuels and carbon monoxide emissions decrease significantly for the methanol blend. A significant reduction in nitric oxide and smoke emissions are observed with the biodiesel-methanol blend investigated.     

Studies on the effect of hydrogen induction on performance,emission and combustion behaviour of a WCO emulsion based dual fuel engine

This paper aims at studying the effect of hydrogen induction on engine performance, emission and combustion behaviour of a diesel engine fuelled with the emulsion of used palm oil (called as WCO-waste cooking oil) as pilot fuel and hydrogen as primary fuel. A single cylinder water-cooled direct injection diesel engine was tested at 100% and 40% loads. Results were compared with neat diesel, neat WCO and WCO emulsion at both loads in single fuel operation. WCO emulsion in single fuel mode indicated improvement in performance and reduction in all emissions as compared to neat WCO. Dual fuel operation with hydrogen induction further reduced the emissions of smoke HC and CO with WCO as pilot fuel at all power outputs. However, hydrogen induction resulted in reduced thermal efficiency at 40% load. WCO emulsion showed higher ignition delay as compared to neat WCO. Dual fuel operation with hydrogen induction increased the ignition delay further. Heat release pattern showed higher premixed combustion rate with hydrogen induction mainly at high power outputs. Premixed combustion rate became very high at higher rates of hydrogen admission mainly at high power output. In general, hydrogen induction showed superior performance at high power output and inferior performance at low power output with WCO emulsion as injected fuel.     

Effect of nanoparticles and hydrogen on combustion performance and exhaust emission of corn blended biodiesel in compression ignition engine with advanced timing

In this study, we have evaluated the influence of Zinc oxide and Titanium dioxide nanoparticles addition in hydrogen-corn blended biodiesel combustion performance and exhaust emission using a dual direct-injection compression-ignition engine. 5% of Zinc oxide and Titanium dioxide were mixed with corn-vegetable oil methyl ester under ultrasonication. Results revealed that the addition of nanoparticles improved the Brake power by 22% (Titanium dioxide) and 4% (Zinc oxide). Consequently, 18% and 15% reduction in brake specific fuel consumption indeed at 50% load compared to neat diesel. Furthermore, the addition of nanoparticles also resulted in a reduction of emission values of 37% and 26% in hydrocarbon, 26% and 36% for carbon monoxide, 19% and 15% in nitrogen oxide and followed by 13% and 8% of smoke opacity. Therefore, the results proved that hydrogen-corn biodiesel blended with nanoparticles additive reports a positive effect on compression-ignition diesel engines without major modifications in engine.     

Investigations on the influence of ethanol and water injection techniques on engine's behavior of a hydrogen - biofuel based dual fuel engine

This work explores the influence of hydrogen and ethanol on improving engine's behavior of Maduca longifolia oil (MO) based dual fuel diesel engine. A mono cylinder diesel engine was tested in dual fuel mode of operation at the rated power output of 3.7 kW under variable hydrogen energy shares from 0 to the maximum allowable limit (until severe knocking i.e. upto 20%). The knock limit was further extended by injecting water and ethanol at the intake manifold and the engine's performance, emission and combustion characteristics were analyzed. In addition ethanol was also injected and introduced along with the intake air for comparison with hydrogen dual fuel mode. Dual fuel operation increased the BTE from 25.2% with neat MO to a maximum of 28.5% and 30% respectively with hydrogen and ethanol for the energy share of 15% and 38% where as the BTE was 30.8% with ND. The smoke opacity was reduced from 78% with neat MO to 58% for the hydrogen energy share of 15% which is the MEP (maximum efficiency point) whereas the smoke emission was noted as 51% with ND operation. However, hydrogen induction increased the NO (nitric oxide) emission. Injection of water and ethanol at the inlet was observed to extend the knocking limit with improved BTE. The BTE reached a maximum of 30.1% with 5% water and 30.8% with 10% ethanol injection. The MEPs were arrived as 31% and 30% hydrogen energy shares respectively with 5% water and 10% ethanol injection. It was concluded that hydrogen induction can be very effective in improving the diesel engine's performance when using MO as base fuel when operating on dual fuel mode. The performance could be improved by extending the knock limit by injecting ethanol and water along with hydrogen.     

Effects of hydrogenation of fossil fuels with hydrogen and hydroxy gas on performance and emissions of internal combustion engines

Energy security is an important consideration for development of future transport fuels. Among the all gaseous fuels hydrogen or hydroxy (HHO) gas is considered to be one of the clean alternative fuels. Hydrogen is very flammable gas and storing and transporting of hydrogen gas safely is very difficult. Today, vehicles using pure hydrogen as fuel require stations with compressed or liquefied hydrogen stocks at high pressures from hydrogen production centres established with large investments.Different electrode design and different electrolytes have been tested to find the best electrode design and electrolyte for higher amount of HHO production using same electric energy. HHO is used as an additional fuel without storage tanks in the four strokes, 4-cylinder compression ignition engine and two-stroke, one-cylinder spark ignition engine without any structural changes. Later, previously developed commercially available dry cell HHO reactor used as a fuel additive to neat diesel fuel and biodiesel fuel mixtures. HHO gas is used to hydrogenate the compressed natural gas (CNG) and different amounts of HHO-CNG fuel mixtures are used in a pilot injection CI engine. Pure diesel fuel and diesel fuel + biodiesel mixtures with different volumetric flow rates are also used as pilot injection fuel in the test engine. The effects of HHO enrichment on engine performance and emissions in compression-ignition and spark-ignition engines have been examined in detail. It is found from the experiments that plate type reactor with NaOH produced more HHO gas with the same amount of catalyst and electric energy. All experimental results from Gasoline and Diesel Engines show that performance and exhaust emission values have improved with hydroxy gas addition to the fossil fuels except NO_x exhaust emissions. The maximum average improvements in terms of performance and emissions of the gasoline and the diesel engine are both graphically and numerically expressed in results and discussions. The maximum average improvements obtained for brake power, brake torque and BSFC values of the gasoline engine were 27%, 32.4% and 16.3%, respectively. Furthermore, maximum improvements in performance data obtained with the use of HHO enriched biodiesel fuel mixture in diesel engine were 8.31% for brake power, 7.1% for brake torque and 10% for BSFC.     

Experimental investigation on diesel engine with diestrol-water micro emulsions

Experiments were conducted on a single cylinder direct injection diesel engine using diesel, biodiesel and biodiesel-diesel-ethanol (diestrol) water micro emulsion fuels to investigate the performance, emission and combustion characteristics of the engine under different load conditions at a constant speed of 1500 rpm. The results indicated that biodiesel and micro emulsion fuels had a higher brake specific fuel consumption (BSFC) than that of diesel. A slight improvement in the brake specific energy consumption (BSEC) was observed for micro emulsion fuels. The brake thermal efficiency of biodiesel and micro emulsion fuels were comparable to that of diesel. The emission characteristics like carbon monoxide (CO), carbon dioxide (CO₂), unburnt hydrocarbon (UHC), nitric oxide (NO) and smoke emissions for biodiesel and micro emulsion fuels were lower than diesel fuel at all load conditions. The cylinder gas pressure of micro emulsion fuels was lower than diesel at low loads but it became almost identical to diesel at medium and full load conditions. The heat release rate for micro emulsion fuels was higher than biodiesel and diesel fuels for all loads. Biodiesel showed shorter ignition delay for the entire load range and the longer ignition delay observed for micro emulsion fuels.     

The effects of turbocharger on the performance and exhaust emissions of a diesel engine fuelled with biodiesel

This paper investigates the effects of turbocharger on the performance of a diesel engine using diesel fuel and biodiesel in terms of brake power, torque, brake specific consumption and thermal efficiency, as well as CO and NO_x emissions. For this aim, a naturally aspirated four-stroke direct injection diesel engine was tested with diesel fuel and neat biodiesel, which is rapeseed oil methyl ester, at full load conditions at the speeds between 1200 and 2400 rpm with intervals of 200 rpm. Then, a turbocharger system was installed on the engine and the tests were repeated for both fuel cases. The evaluation of experimental data showed that the brake thermal efficiency of biodiesel was slightly higher than that of diesel fuel in both naturally aspirated and turbocharged conditions, while biodiesel yielded slightly lower brake power and torque along with higher fuel consumption values. It was also observed that emissions of CO in the operations with biodiesel were lower than those in the operations with diesel fuel, whereas NO_x emission in biodiesel operation was higher. This study reveals that the use of biodiesel improves the performance parameters and decreases CO emissions of the turbocharged engine compared to diesel fuel.     

Impact of Carbon Nanotubes and Di-Ethyl Ether as additives with biodiesel emulsion fuels in a diesel engine – An experimental investigation

In the current global energy scenario, fossil fuels face challenges with regards to exorbitant demand, environmental hazards and escalating costs. In this regard, the technical community is in quest for alternative resources. In this context, biodiesel fuel is potentially considered as alternative fuels for compression ignition engines. Hence, in this current investigation, biodiesel and biodiesel emulsions are prepared from a vegetable oil and further subjected for the blending with potential additives such as CNT (Carbon Nanotubes) and DEE (Di-Ethyl Ether) to improve the working attributes of the diesel engine. The entire investigation was carried out in five stages. In the first stage, both pure diesel and biodiesel (derived from jatropha oil) fuels were tested in the diesel engine to obtain baseline readings. In the second stage, water–biodiesel emulsion fuel was prepared in the proportion of 91% of biodiesel, 5% of water and 4% of emulsifiers (by volume). In the third stage, 50 ppm of CNT, 50 ml of DEE and combined mixture of CNT+DEE (50 ppm CNT+50 ml DEE) were mixed with the water–biodiesel emulsion fuel separately to prepare the CNT and DEE blended water–biodiesel emulsion fuels respectively. In fourth stage, the prepared emulsion fuels were subjected to stability investigations. In the fifth stage, all the prepared stable emulsion fuels were subjected for experimental testing in a diesel engine. It was observed that the CNT and DEE blended biodiesel emulsion fuels reflected better performance, emission and combustion attributes than that of pure diesel and biodiesel. At the full load, the brake thermal efficiency, NO and smoke emission of CNT+DEE fuels was 28.8%, 895 ppm and 36%, whereas it was 25.2%, 1340 ppm and 71% for pure diesel respectively. It was also observed that on adding CNT and DEE with the biodiesel emulsion fuels, the ignition delay was shortened and henceforth, the additive blended biodiesel emulsion fuels exhibited higher brake thermal efficiency and reduced emissions (NO, smoke) than that of pure diesel and biodiesel.     

Effect of hydrogen on compression-ignition (CI) engine fueled with vegetable oil/biodiesel from various feedstocks: A review

Compression ignition (CI) engines used in the transportation sector operates on fossil diesel and is one of the biggest causes of air pollution. Numerous studies were carried out over last two decades to substitute the fossil diesel with biofuels so that the net carbon dioxide (CO₂) emission can be minimized. However, the engine performance with these fuel was sub-standard and there were many long-term issues. Therefore, many researchers inducted hydrogen along with the biofuels. The present study gives an outlook on the effect of hydrogen addition with biodiesel/vegetable oil from various sources in CI engine. Engine parameters (brake thermal efficiency, brake specific fuel consumption), combustion parameters (in-cylinder pressure and heat release rate) and emission parameters (unburned hydrocarbon (HC), carbon monoxide (CO), oxides of nitrogen (NOx) and smoke emissions) were evaluated in detail. The results show that hydrogen induction in general improves the engine performance as compared to biodiesel/vegetable oil but it is similar/lower than diesel. Except NOx emissions all other emissions showed a decreasing trend with hydrogen addition. To counter this effect numerous after-treatment systems like selective catalytic reduction (SCR), exhaust gas recirculation (EGR), selective non-catalytic reduction system (SNCR) and non-selective catalytic reduction system (NSCR) were proposed by researchers which were also studied in this review.     

发动机燃用生物柴油的性能研究

通过对比研究了柴油机燃用餐饮废弃油炼制的生物柴油、柴油及B50时在高原地区的动力性、经济性及排放特性。研究结果表明：在柴油机不进行任何调整的情况下,全负荷时,燃用生物柴油的发动机动力性降低6.8%,B50降低3%;燃用生物柴油有效燃油消耗率升高了13.8%;燃用B50在高速高负荷时柴油机热效率提高2.5%;无论在全负荷还是在部分负荷工况下,燃用生物柴油均能大幅度降低柴油机烟度、CO和HC排放,但会引起NOx排放量的上升。     

Effect of methanol fumigation on performance and emission characteristics in a waste cooking oil-fuelled single cylinder CI engine

Use of bio-oils in diesel engines results in increased NOx and smoke and reduced brake thermal efficiency. Dual-fuel engines can use a wide range of fuels mainly alcohols and yet operate with high thermal efficiency and simultaneous reduction of NO and smoke emissions. The present study aims to explore the effect of methanol–waste cooking oil (WCO) dual-fuel mode on performance and emission characteristics in a single cylinder Compression ignition (CI) engine producing 3.7 kW at 1,500 rpm. WCO was injected in the conventional injection system, replacing diesel as pilot fuel. Methanol was fumigated along with intake air using a variable jet carburetor, which was installed in the inlet manifold. The methanol was fumigated, and the energy share was varied for each load till the knock limit. Performance parameters like brake thermal efficiency (BTE) and emission parameters like HC, CO, NO, and smoke emissions were tested for various energy shares of methanol with WCO as a pilot fuel. The results show that an increase in methanol fumigation reduced BTE at lower loads. At 75% and 100% load conditions, BTE was higher with methanol addition. The maximum BTE was observed for 38% methanol share, which is about 11% higher, compared to WCO at 100% load condition. Methanol fumigation aided in the simultaneous reduction of NO and smoke emission, and the maximum reduction was occurred with 51% methanol share at 100% load condition. HC and CO emissions were higher at all load conditions with methanol fumigation.     

Effect of induction on exhaust gas recirculation and hydrogen gas in compression ignition engine with simarouba oil in dual fuel mode

Biofuels extracted from non-edible oil is sustainable and can be used as an alternative fuel for internal combustion engines. This study presents the performance, emission and combustion characteristic analysis by using simarouba oil (obtained from Simarouba seed) as an alternative fuel along with hydrogen and exhaust gas recirculation (EGR) in a compression ignition (CI) engine operating on dual fuel mode. Simarouba biofuel blend (B20) was prepared on volumetric basis by mixing simarouba oil and diesel in the proportion of 20% and 80% (v/v), respectively. Hydrogen gas was introduced at the flow rate of 2.67 kg/min, and EGR concentration was maintained at 30% of total air introduction. Performance, combustion and emission characteristics analysis were examined with biodiesel (B20), biodiesel with hydrogen substitution and biodiesel, hydrogen with EGR and were compared with neat diesel operation. Results indicate that BTE of the engine operating with biodiesel B20 was decreased when compared to neat diesel operation. However, introducing hydrogen along with B20 blend into the combustion chamber shows a slight increase in the BTE by 1%. NO_x emission was increased to 18.13% with the introduction of hydrogen than that of base fuel (diesel) operation. With the introduction of EGR, there is a significant reduction in NO_x emission due to decrease in in-cylinder temperature by 19.07%. A significant reduction in CO, CO_2, and smoke emissions were also noted with the introduction of both hydrogen and EGR. The ignition delay and combustion duration were increased with the introduction of hydrogen, EGR with biodiesel than neat diesel operation. Hence, the proposed biodiesel B20 with H₂ and EGR combination can be applied as an alternative fuel in CI engines.     

Optimisation of dry cell electrolyser and hydroxy gas production to utilise in a diesel engine operated with blends of orange peel oil in dual-fuel mode

This study aims at producing hydroxy (HHO) gas using a dry cell electrolysis setup and utilising it along with orange oil in a diesel engine. First an electrolyser was designed considering the optimised values of the material (SS316L), electrolyte (NaOH), and electrode gap (2 mm). Then the biodiesel obtained from the waste orange peels, after transesterification, were blended with diesel at 25 and 50% by vol. The HHO gas was produced by the water electrolysis method by a plate-type electrolyser having a maximum production rate of 2.5 LPM with NaOH as the electrolyte. HHO gas was inducted through the inlet manifold along with the fresh air at a constant rate of 2 LPM with both the biodiesel blends. The performance, emission, and combustion outcomes of the single cylinder diesel engine for different load conditions (0–100%) were tested for all the blends with and without HHO addition. The results showed a considerable increase in brake thermal efficiency of 1.54% at full load condition, with a noticeable decrease in fuel consumption by 11.1% compared to conventional diesel fuel, was achieved for the O25 blend with HHO induction. Moreover, emissions like hydrocarbon, carbon monoxide and smoke were reduced by 17.6, 29.5, and 12.1%, respectively. However, the improvement in combustion outcomes led to the increase in nitrogen oxides emission by 9.67%. This study helped to understand the production process of HHO gas by dry cell electrolyser and its effect on the blend of orange oil methyl ester and diesel in dual-fuel mode.     

Environment effect of La2O3 nano-additives on microalgae-biodiesel fueled CRDI engine with conventional diesel

In this present work, corn oil biodiesel with La₂O₃ was used as an additive with neat diesel fuel and blends were prepared. La₂O₃ nanoparticles are dispersed in the emulsions with different dosage levels of 50, 75, and 100 ppm. A single-cylinder, four-stroke CRDI diesel engine is made to run on different fuel concentrations to study the effect of emission characteristics of the fuel. The test engine was operated under constant engine speed (1500 rpm) and different engine load test conditions. According to the experimental results, fuel blends with biodiesel fuel emission increases CO₂ and NOx and reduces the CO, HC, and smoke emissions compared with the B20 fuel.     

Hydrogen-enriched palm biodiesel as a potential alternative fuel for diesel engines: Investigating performance and emission characteristics and mitigation strategies for air pollutants

Palm biodiesel is one of the most suitable alternative fuels due to its capability to replace traditional fossil fuel usage in IC engines. Even as palm biodiesel (POBD) reduces harmful pollutant gases, the engine performance is not on an equal scale with neat diesel. To address this shortcoming, an investigation was carried out to examine the application of palm biodiesel (PBD) and hydrogen induction through the intake air at the flow rates of 6 and 8LPM (Litre Per Minute) in the compression ignition (CI) engine. The experimental study shows that POBD has poor engine performance and moderate pollution reduction compared with neat diesel. When compared to POBD and neat diesel, the higher calorific value and other H₂ characteristics improve combustion properties, resulting in higher engine performance and lower pollutant gases (except NOx). When compared to the palm biodiesel blend (BD 30), the results of BD30+8LPM reduced the Specific fuel consumption (SFC) by 0.0885kg/kWh and improved the brake thermal efficiency (BTE) by 6.67%. The Carbon monoxide (CO), hydro carbon (HC), and smoke opacity were reduced by 0.047% volume, 29.2 ppm, and 6.52% respectively. A marginal increase in NOx was seen as 297.6 ppm.     

Using of cotton oil soapstock biodiesel–diesel fuel blends as an alternative diesel fuel

In this study, usability of cotton oil soapstock biodiesel–diesel fuel blends as an alternative fuel for diesel engines were studied. Biodiesel was produced by reacting cotton oil soapstock with methyl alcohol at determined optimum condition. The cotton oil biodiesel–diesel fuel blends were tested in a single cylinder direct injection diesel engine. Engine performances and smoke value were measured at full load condition. Torque and power output of the engine with cotton oil soapstock biodiesel–diesel fuel blends decreased by 5.8% and 6.2%, respectively. Specific fuel consumption of engine with cotton oil soapstock–diesel fuel blends increased up to 10.5%. At maximum torque speeds, smoke level of engine with blend fuels decreased up to 46.6%, depending on the amount of biodiesel. These results were compared with diesel fuel values.     

Effect of hydrogen and LPG addition on the efficiency and emissions of a dual fuel diesel engine

This paper presents some experimental investigations on dual fuel operation of a 4 cylinder (turbocharged and intercooled) 62.5 kW gen-set diesel engine with hydrogen, liquefied petroleum gas (LPG) and mixture of LPG and hydrogen as secondary fuels. Results on brake thermal efficiency and emissions, namely, un-burnt hydrocarbon (HC), carbon monoxide (CO), NO_x and smoke are presented here. The paper also includes vital information regarding performances of the engine at a wide range of load conditions with different gaseous fuel substitutions. When only hydrogen is used as secondary fuel, maximum enhancement in the brake thermal efficiency is 17% which is obtained with 30% of secondary fuel. When only LPG is used as secondary fuel, maximum enhancement in the brake thermal efficiency (of 6%) is obtained with 40% of secondary fuel. Compared to the pure diesel operation, proportion of un-burnt HC and CO increases, while, emission of NO_x and smoke reduces in both cases. On the other hand, when 40% of mixture of LPG and hydrogen is used (in the ratio 70:30) as secondary fuel, brake thermal efficiency enhances by 27% and HC emission reduces by 68%. Further, shortcoming of low efficiency at lower load condition in a dual fuel operation is removed when a mixture of hydrogen and LPG is used as the secondary fuel at higher than 10% load condition.