Combined catalytic partial oxidation and CO2 reforming of methane over ZrO2-modified Ni/SiO2 catalysts using fluidized-bed reactor

Nickel on zirconium-modified silica was prepared and tested as a catalyst for reforming methane with CO₂ and O₂ in a fluidized-bed reactor. A conversion of CH₄ near thermodynamic equilibrium and low H₂/CO ratio (1<H₂/CO<2) were obtained without catalyst deactivation during 10 h, in a most energy efficient and safe manner. A weight loading of 5 wt% zirconium was found to be the optimum. The catalysts were characterized using X-ray diffraction (XRD), H₂-temperature reaction (H₂-TPR), CO₂-temperature desorption (CO₂-TPD) and transmission election microscope (TEM) techniques. Ni sintering was a major reason for the deactivation of pure Ni/SiO₂ catalysts, while Ni dispersed highly on a zirconium-promoted Ni/SiO₂ catalyst. The different kinds of surface Ni species formed on ZrO₂-promoted catalysts might be responsible for its high activity and good resistance to Ni sintering.     

Aqueous-phase reforming of n-BuOH over Ni/Al2O3 and Ni/CeO2 catalysts

The aqueous-phase reforming (APR) of n-butanol (n-BuOH) over Ni(20 wt%) loaded Al₂O₃ and CeO₂ catalysts has been studied in this paper. Over 100 h of run time, the Ni/Al₂O₃ catalyst showed significant deactivation compared to the Ni/CeO₂ catalyst, both in terms of production rates and the selectivity to H₂ and CO₂. The Ni/CeO₂ catalyst demonstrated higher selectivity for H₂ and CO₂, lower selectivity to alkanes, and a lower amount of C in the liquid phase compared to the Ni/Al₂O₃ sample. For the Ni/Al₂O₃ catalyst, the selectivity to CO increased with temperature, while the Ni/CeO₂ catalyst produced no CO. For the Ni/CeO₂ catalyst, the activation energies for H₂ and CO₂ production were 146 and 169 kJ mol⁻¹, while for the Ni/Al₂O₃ catalyst these activation energies were 158 and 175 kJ mol⁻¹, respectively. The difference of the active metal dispersion on Al₂O₃ and CeO₂ supports, as measured from H₂-pulse chemisorption was not significant. This indicates deposition of carbon on the catalyst as a likely cause of lower activity of the Ni/Al₂O₃ catalyst. It is unlikely that carbon would build up on the Ni/CeO₂ catalyst due to higher oxygen mobility in the Ni doped non-stoichiometric CeO₂ lattice. Based on the products formed, the proposed primary reaction pathway is the dehydrogenation of n-BuOH to butaldehyde followed by decarbonylation to propane. The propane then partially breaks down to hydrogen and carbon monoxide through steam reforming, while CO converts to CO₂ mostly through water gas shift. Ethane and methane are formed via Fischer-Tropsch reactions of CO/CO₂ with H₂.     

Reforming of bioethanol over Ni/Al2O3 and Ni/CeZrO2/Al2O3 catalysts in supercritical water for hydrogen production

Bioethanol was reformed in supercritical water (SCW) at 500 °C and 25 MPa on Ni/Al₂O₃ and Ni/CeZrO₂/Al₂O₃ catalysts to produce high-pressure hydrogen. The results were compared with non-catalytic reactions. Under supercritical water and in a non-catalytic environment, ethanol was reformed to H₂, CO₂ and CH₄ with small amounts of CO and C2 gas and liquid products. The presence of either Ni/Al₂O₃ or Ni/CeZrO₂/Al₂O₃ promoted reactions of ethanol reforming, dehydrogenation and decomposition. Acetaldehyde produced from the decomposition of ethanol was completely decomposed into CH₄ and CO, which underwent a further water-gas shift reaction in SCW. This led to great increases in ethanol conversion and H₂ yield on the catalysts of more than 3-4 times than that of the non-catalytic condition. For the catalytic operation, adding small amounts of oxygen at oxygen to ethanol molar ratio of 0.06 into the feed improved ethanol conversion, at the expense of some H₂ oxidized to water, resulting in a slightly lower H₂ yield. The ceria-zirconia promoted catalyst was more active than the unpromoted catalyst. On the promoted catalyst, complete ethanol conversion was achieved and no coke formation was found. The ceria-zirconia promoter has important roles in improving the decomposition of acetaldehyde, the enhancement of the water-gas shift as well as the methanation reactions to give an extremely low CO yield and a tremendously high H₂/CO ratio. The SCW environment for ethanol reforming caused the transformation of gamma-alumina towards the corundum phase of the alumina support in the Ni/Al₂O₃ catalyst, but this transformation was slowed down by the presence of the ceria-zirconia promoter.     

CO2 reforming of methane combined with steam reforming or partial oxidation of methane to syngas over NdCoO3 perovskite-type mixed metal-oxide catalyst

CO₂ reforming with simultaneous steam reforming or partial oxidation of methane to syngas over NdCoO₃ perovskite-type mixed metal oxide catalyst (prereduced by H₂) at different process conditions has been investigated. In the simultaneous CO₂ and steam reforming, the conversion of methane and H₂O and also the H₂/CO product ratio are strongly influenced by the CO₂/H₂O feed-ratio. In the simultaneous CO₂ reforming and partial oxidation of methane, the conversion of methane and CO₂, H₂ selectivity and the net heat of reaction are strongly influenced by the process parameters (viz. temperature, space velocity and relative concentration of O₂ in the feed). In both cases, no carbon deposition on the catalyst was observed. The reduced NdCoO₃ perovskite-type mixed-oxide catalyst (Co dispersed on Nd₂O₃) is a highly promising catalyst for carbon-free CO₂ reforming combined with steam reforming or partial oxidation of methane to syngas.     

Synthesis of nanocrystalline mesoporous Ni/Al2O3SiO2 catalysts for CO2 methanation reaction

A series of nanocrystalline mesoporous Ni/Al₂O₃SiO₂ catalysts with various SiO₂/Al₂O₃ molar ratios were prepared by the sol-gel method for the carbon dioxide methanation reaction. The synthesized catalysts were evaluated in terms of catalytic performance and stability. The catalysts were studied using XRD, BET, TPR and SEM. The BET results indicated that the specific surface area of the samples with composite oxide support changed from 254 to 163.3 m²/g, and an increase in the nickel crystallite size from 3.53 to 5.14 nm with an increment of Si/Al molar ratio was visible. The TPR results showed a shift towards lower temperatures, indicating a better reducibility and easier reduction of the nickel oxide phase into the nickel metallic phase. Furthermore, the catalyst with SiO₂/Al₂O₃ molar ratio of 0.5 was selected as the optimal catalyst, which showed 82.38% CO₂ conversion and 98.19% CH₄ selectivity at 350 °C, high stability, and resistivity toward sintering. Eventually, the optimal operation conditions were specified by investigating the effect of H₂/CO₂ molar ratio and gas hourly space velocity (GHSV) on the catalytic behavior of the denoted catalyst.     

Combined air partial oxidation and CO2 reforming of coal bed methane to synthesis gas over co-precipitated Ni-Mg-ZrO2 catalyst

The present study aims at exploring a concept which can convert coal-bed methane (containing methane, air and carbon dioxide) to synthesis gas. Without pre-separation and purification, the low-cost synthesis gas can be produced by coupling air partial oxidation and CO₂ reforming of coal bed methane. For this purpose, the co-precipitated Ni-Mg-ZrO₂ catalyst was prepared. It was found that the co-precipitated Ni-Mg-ZrO₂ catalyst exhibited the best activity and stability at 800 °C during the reaction. The conversions of CH₄ and CO₂ maintained at 94.8% and 82.1% respectively after 100 h of reaction. The effect of reaction temperature was investigated. The H₂/CO ratio in the product was mainly dependent on the feed gas composition. By changing O₂/CO₂ ratio of the feed gases, the H₂/CO ratio in the off-gas varied between 0.8 and 1.8. The experimental results showed that the high thermal stability and basic properties of the catalyst, and the strong metal-support interaction played important roles in improving the activity and stability of the catalyst. With the combined reactions and the Ni-Mg-ZrO₂ catalyst, the coal bed methane could be converted to synthesis gas, which can meet the need of the subsequent synthesis processes.     

The promoting effect of La, Mg, Co and Zn on the activity and stability of Ni/SiO2 catalyst for CO2 reforming of methane

CO₂ reforming of methane into synthesis gas over Ni/SiO₂ catalysts promoted by La, Mg, Co and Zn was investigated. The catalysts were prepared by impregnation method and characterized by XRD, TPR, SEM and TG-DTA techniques. Ni-La/SiO₂ catalyst was found to exhibit high activity and excellent stability with the addition of suitable amount of La promoter, which increased the dispersion of NiO and the interaction between NiO and SiO₂. Two different types of carbon species, namely, easily oxidized carbonaceous species and inert carbon, were observed on the surface of the used catalysts. The inert carbon deposited on Ni-Mg/SiO₂ catalyst may be the main reason for its deactivation, while the principal reason for the deactivation of Ni-Co/SiO₂ catalyst might be the sintering of metallic Ni. The addition of La and Mg decreased the contribution of reverse water-gas shift reaction, leading to higher H₂ yield.     

Catalytic conversion of CH4 and CO2 to synthesis gas on Ni/SiO2 catalysts containing Gd2O3 promoter

A series of Ni/SiO₂ catalysts containing different amounts of Gd₂O₃ promoter was prepared, characterized by H₂-adsorption and XRD, and used for carbon dioxide reforming of methane (CRM) and methane autothermal reforming with CO₂ + O₂ (MATR) in a fluidized-bed reactor. The results of pulse surface reactions showed that Ni/SiO₂ catalysts containing Gd₂O₃ promoter could increase the activity for CH₄ decomposition, and Raman analysis confirmed that reactive carbon species mainly formed on the Ni/SiO₂ catalysts containing Gd₂O₃ promoter. In this work, it was found that methane activation and reforming reactions proceeded according to different mechanisms after Gd₂O₃ addition due to the formation of carbonate species. In addition, Ni/SiO₂ catalysts containing Gd₂O₃ promoter demonstrated higher activity and stability in both CRM and MATR reactions in a fluidized bed reactor than Ni/SiO₂ catalysts without Gd₂O₃ even at a higher space velocity.     

Investigation of water gas-shift activity of Pt–MOx–CeO2/Al2O3 (M = K,Ni, Co) using modular artificial neural networks

The water gas shift activity of promoted Pt–CeO₂/Al₂O₃ catalysts were investigated in this work. The catalysts were prepared by incipient to wetness impregnation and tested using a microflow reaction system. It was found that K has beneficial effects under product-containing feed compositions while Co and Ni promoters worsen catalyst performance. The reaction temperature and feed H₂O/CO ratio positively affect the catalytic activity, whereas CO₂ and H₂ addition to the feed decreases CO conversion, as expected. The experimental results were also modeled using modular neural networks, at which the catalyst preparation and operational (reaction) variables were used together in the same network because they are interacting but processed differently because they are dissimilar in their form (i.e. categorical versus continuous) and their effects on catalytic activity. It was concluded that the effects of catalyst preparation and operational variables and their relative importance could be comprehended more accurately by using this approach, which may be also employed in other similar systems.     

Enhancement of the quality of syngas from catalytic steam gasification of biomass by the addition of methane/model biogas

In this study, methane and model biogas were added during the catalytic steam gasification of pine to regulate the syngas composition and improve the quality of syngas. The effects of Ni/γ-Al₂O₃ catalyst, steam and methane/model biogas on H₂/CO ratio, syngas yield, carbon conversion rate and tar yield were explored. The results indicated that the addition of methane/model biogas during biomass steam gasification could increase the H₂/CO ratio to about 2. Methane/model biogas, steam and Ni/γ-Al₂O₃ catalyst significantly affected the quality of syngas. High H₂ content syngas with H₂/CO ratio of about 2, biomass carbon conversion >85% and low tar yield was achieved under the optimum condition: S/C = 1.5, α = 0.2 and using Ni/γ-Al₂O₃ catalyst. According to ANOVA, methane and catalyst were the key influencing factors of the H₂/CO ratio and syngas yield, and the tar yield mainly depended on the Ni/γ-Al₂O₃ catalyst. Biogas, as a more environmentally friendly material than methane, can also regulate the composition of syngas co-feeding with biomass.     

Comparative study on the promotion effect of Mn and Zr on the stability of Ni/SiO2 catalyst for CO2 reforming of methane

The stability of Mn-promoted Ni/SiO₂ catalyst for methane CO₂ reforming was investigated comparatively to that of Zr-promoted Ni/SiO₂. The catalysts were prepared by the same impregnation method with the same controlled promoter contents and characterized by TPR, XRD, TG, SEM, XPS and Raman techniques. The addition of Mn to Ni/SiO₂ catalyst promoted the dispersion of Ni species, leading to smaller particle size of NiO on the fresh Ni–Mn/SiO₂ catalyst and the formation of NiMn₂O₄, which enhanced the interaction of the modified support with Ni species. Thus, the Ni–Mn/SiO₂ catalyst showed higher activity and better ability of restraining carbon deposition than Ni/SiO₂ catalyst. Besides, it exhibited stable activity at reaction temperatures over the range from 600 °C to 800 °C. However, the introduction of Zr increased the reducibility of Ni–Zr/SiO₂, and the catalyst deactivated much more dramatically when the reaction temperature decreased due to its poor ability of restraining carbon deposition, and its activity decreased monotonically with time on stream at 800 °C.     

Effects of modifying Ni/Al2O3 catalyst with cobalt on the reforming of CH4 with CO2 and cracking of CH4 reactions

Alumina supported nickel (Ni/Al₂O₃), nickel–cobalt (Ni–Co/Al₂O₃) and cobalt (Co/Al₂O₃) catalysts containing 15% metal were synthesized, characterized and tested for the reforming of CH₄ with CO₂ and CH₄ cracking reactions. In the Ni–Co/Al₂O₃ catalysts Ni–Co alloys were detected and the surface metal sites decreased with decrease in Ni:Co ratio. Turnover frequencies of CH₄ were determined for both reactions. The initial turnover frequencies of reforming (TOF_DRM) for Ni–Co/Al₂O₃ were greater than that for Ni/Al₂O₃, which suggested a higher activity of alloy sites. The initial turnover frequencies for cracking (TOF_CRK) did not follow this trend. The highest average TOF_DRM, H₂:CO ratio and TOF_CRK were observed for a catalyst containing a Ni:Co ratio of 3:1. This catalyst also had the maximum carbon deposited during reforming and produced the maximum reactive carbon during cracking. It appeared that carbon was an intermediate product of reforming and the best catalyst was able to most effectively crack CH₄ and oxidize carbon to CO by CO₂.     

High quality syngas production from pressurized K2CO3 catalytic coal gasification with in-situ CO2 capture

The enhanced K-catalytic coal gasification by CO₂ sorption reaction (EKcSG) was proposed to produce syngas with high content of H₂ and CH₄ and perform in-situ CO₂ capture. CO₂ is reduced dramatically with the introduction of the CaO into the reactor under typical K-catalytic coal gasification condition (3.5 MPa, 700 °C). The carbonation reaction of CaO can promote the syngas production by improving the equilibrium of the water-gas shift reaction and supplying heat for coal gasification reaction. In the presence of the CaO sorbent (Ca/C = 0.5), the CO₂ concentration in the product gas decreased from 25.61% to 12.80% compared with that without CaO. Correspondingly, the total concentration of H₂ and CH₄ is improved from 65.61% to 82.99% and the carbon conversion reached above 95%. The effect of Ca/C ratio and reaction temperature was investigated during the EKcSG process. It is considered that Ca/C ratio of 0.5 is the best proportion in terms of carbon conversion and CO₂ absorption in our experimental conditions.     

Effect of preparation methods on the performance of Ni/Al2O3 catalysts for aqueous-phase reforming of ethanol: Part I-catalytic activity

The effect of preparation method on the performance of Ni/Al₂O₃ catalysts for aqueous-phase reforming of ethanol (EtOH) has been investigated. The first catalyst was prepared by a sol–gel (SG) method and for the second one the Al₂O₃ support was made by a solution combustion synthesis (SCS) route and then the metal was loaded by standard wet impregnation. The catalytic activity of these catalysts of different Ni loading was compared with a commercial Al₂O₃ supported Ni catalyst [CM (10%)] at different temperatures, pressures, feed flow rates, and feed concentrations. Based on the product distribution, the proposed reaction pathway is a mixture of dehydrogenation of EtOH to CH₃CHO followed by C–C bond breaking to produce CO + CH₄ and oxidation of CH₃CHO to CH₃COOH followed by decarbonylation to CO₂ + CH₄. CH₄(C₂H₆ and C₃H₈) also can form via Fischer–Tropsch reactions of CO/CO₂ with H₂. The CH₄ (C₂H₆ and C₃H₈) reacts to form hydrogen and carbon monoxide through steam reforming, while CO converts to CO₂ mostly through the water–gas shift reaction (WGSR). SG catalysts showed poorer WGSR activity than the SCS catalysts. The activation energies for H₂ and CO₂ production were 153, 155 and 167 kJ/mol and 158, 160 and 169 kJ/mol for SCS (10%), SG (10%), and CM (10%) samples, respectively.     

Toluene steam reforming properties of CaO based synthetic sorbents for biomass gasification process

Biomass gasification process generates undesired Topping Atmosphere Residue (TAR), removable by catalytic steam reforming. The use of a CO₂-sorbent powder inside the reactor bed can minimize the content of carbon dioxide and carbon monoxide by enhancing the water gas shift (WGS) reaction, offering a fuel gas rich of H₂. The present study addresses the practical feasibility of such concepts, using toluene as a representative TAR and a hybrid compound Ni/CaO–Ca₁₂Al₁₄O₃₃ as reactor bed material, simultaneously acting as reforming catalyst and CO₂ sorbent. In fact, the CaO is the effective sorbent, whereas the Ca₁₂Al₁₄O₃₃ is a support for both the CaO and the active metallic Ni particles. A different synthesis route with respect to the literature has been developed for the production of the Ni/CaO–Ca₁₂Al₁₄O₃₃ and a total of three different bed reactor powders have been tested and compared: (i) a mixture of olivine and commercial nickel catalyst, (ii) a mixture of CaO–Ca₁₂Al₁₄O₃₃ and commercial nickel catalyst, and (iii) the Ni/CaO–Ca₁₂Al₁₄O₃₃ combined catalyst and sorbent. The best performances have been observed in the latter, with toluene conversion close to 99%, and the volume fraction of hydrogen in the gas over 95%. During multi-cycle tests, the synthetic Ni/CaO–Ca₁₂Al₁₄O₃₃ combined catalyst and sorbent exhibited superior resistance to carbon deposition and stability in toluene conversion compared to the other bed materials that suffer from decreased conversion efficiency after few cycles.     

Ni/MgAl2O4 catalyst for low-temperature oxidative dry methane reforming with CO2

Oxidative dry reforming of methane has been performed for 100 h on stream using Ni supported on MgAl₂O₄ spinel at different loadings at 500–700 °C, CO₂/CH₄ molar ratio of 0.76, and variable O₂/CH₄ molar ratio (0.12–0.47). Syngas with an H₂/CO ratio of 1.5–2.1 has been produced by manipulating reforming feed composition and temperature. The developed oxidative dry reforming process allowed high CH₄ conversion at all conditions, while CO₂ conversion decreased significantly with the lowering of the reforming temperature and increasing O₂ concentration. When considering both greenhouse gas conversions and H₂/CO ratio enhancement, the optimal reforming condition should be assigned to 550 °C and O₂/CH₄ molar ratio of 0.47, which delivered syngas with H₂/CO ratio of 1.5. Coke-free operation was also achieved, due to the combustion of surface carbon species by oxygen. The 3.4 wt% Ni/MgAl₂O₄ catalyst with a mean Ni nanoparticle diameter of 9.8 nm showed stable performance during oxidative dry reforming for 100 h on stream without deactivation by sintering or coke deposition. The superior activity and stability of MgAl₂O₄ supported Ni catalyst shown during reaction trials is consistent with characterization results from XRD, TPR, STEM, HR-STEM, XPS, and CHNS analysis.     

Why Ni/CeO2 is more active than Ni/SiO2 for CO2 methanation? Identifying effect of Ni particle size and oxygen vacancy

An impregnated Ni/CeO₂ catalyst with an array structure and a phyllosilicate-based Ni/SiO₂ catalyst prepared by hydrothermal method were designed for CO₂ methanation. The as-synthetized Ni/SiO₂ catalyst exhibits a high Ni content of 25.9 wt%, while its CO₂ conversion at low temperature is far lower than that of Ni/CeO₂, whose Ni content is only 10.0 wt%. TEM and XRD results show that the Ni/CeO₂ catalyst possesses very tiny Ni particle size of around 1.2 nm, which leads to large H₂ uptake capacity. XPS and Raman analyses indicate that Ni/CeO₂ obtains more oxygen vacancies resulting in promotion of the CO₂ activation. The combined effect of the Ni/CeO₂ catalyst to enhance chemisorption of H₂ and CO₂ leads to high low-temperature activity.     

Promotional effect of alkaline earth over Ni-La2O3 catalyst for CO2 reforming of CH4: Role of surface oxygen species on H2 production and carbon suppression

Alkaline earth elements (Mg, Ca and Sr) on Ni-La₂O₃ catalyst have been investigated as promoters for syngas production from dry CO₂ reforming of methane (DRM). The catalysis results of DRM performance at 600 °C show that the Sr-doped Ni-La₂O₃ catalyst not only yields the highest CH₄ and CO₂ conversions (∼78% and ∼60%) and highest H₂ production (∼42% by vol.) but also has the lowest carbon deposition over the catalyst surface. The XPS, O₂-TPD, H₂-TPR and FTIR results show that the excellent performance over the Sr-doped Ni-La₂O₃ catalyst is attributed to the presence of a high amount of lattice oxygen surface species which promotes C-H activation in DRM reaction, resulting in high H₂ production. Moreover, these surface oxygen species on the Ni-SDL catalyst can adsorb CO₂ molecules to form bidentate carbonate species, which can then react with the surface carbon species formed during DRM, resulting in higher CO₂ conversion and lower carbon formation.     

Synthesis gas production in the combined CO2 reforming with partial oxidation of methane over Ce-promoted Ni/SiO2 catalysts

A series of nickel-based catalyst supported on silica (Ni/SiO₂) with different loading of Ce/Ni (molar ratio ranging from 0.17 to 0.84) were prepared using conventional co-impregnation method and were applied to synthesis gas production in the combination of CO₂ reforming with partial oxidation of methane. Among the cerium-containing catalysts, the cerium-rich ones exhibited the higher activity and stability than the cerium-low ones. The temperature-programmed reduction (TPR) and UV–vis diffuse reflectance spectroscopy (UV–vis DRS) analysis revealed that the addition of CeO₂ reduced the chemical interaction between Ni and support, resulting in an increase in reducibility and dispersion of Ni. Over NiCe-x/SiO₂ (x = 0.17, 0.50, 0.67, 0.84) catalysts, the reduction peak in TPR profiles shifted to the higher temperature with increasing Ce/Ni molar ratio, which was attributed to the smaller metallic nickel size of the reduced catalysts. The transmission electron microscopy (TEM) and X-ray diffraction (XRD) for the post-reaction catalysts confirmed that the promoter retained the metallic nickel species and prevented the metal particle growth at high reaction temperature. The NiCe-0.84/SiO₂ catalyst with small Ni particle size exhibited the stable activity with the constant H₂/CO molar ratio of 1.2 during 6-h reaction in the combination of CO₂ reforming with partial oxidation of methane at 850 °C and atmospheric pressure.     

Optimization of renewable hydrogen-rich syngas production from catalytic reforming of greenhouse gases (CH4 and CO2) over calcium iron oxide supported nickel catalyst

Multi-response optimization of hydrogen-rich syngas from catalytic reforming of greenhouses (methane and carbon dioxide over Calcium iron oxide supported Nickel (15 wt%Ni/CaFe₂O₄) catalyst was performed by varying reaction temperature (700–800 °C), feed ratio (0.4–1.0) and gas hourly space velocity (10,000–60,000 h^?1)) using response surface methodology. Four response surface methodology (RSM) models were obtained for the prediction of reactant conversion and the product yield. The analysis of variance (ANOVA) conducted on the model showed that the parameters have significant effect on the responses. Optimum conditions for the methane dry reforming over the 15 wt%Ni/CaFe₂O₄ catalyst were obtained at reaction temperature, feed ratio and gas hourly space velocity (GHSV) of 832.45 °C, 0.96 and 35,000 mL g^?1 h^?1 respectively with overall desirability value of 0.999 resulting in the highest methane (CH₄) and carbon dioxide (CO₂) conversions of 85.00%, 88.00% and hydrogen (H₂) and carbon monoxide (CO) yields of 77.82% and 75.76%, respectively.