Integrated Hydrogen-Sensing Amplifier With GaAs Schottky-Type Diode and InGaP–GaAs Heterojunction Bipolar Transistor

New hydrogen-sensing amplifiers are fabricated by integrating a GaAs Schottky-type hydrogen sensor and an InGaP–GaAs heterojunction bipolar transistor. Sensing collector currents ( $I_{rm CN}$ and $I_{rm CH}$) reflecting to $hbox{N}_{2}$ and hydrogen-containing gases are employed as output signals in common-emitter characteristics. Gummel-plot sensing characteristics with testing gases as inputs show a high sensing-collector-current gain $(I_{rm CH}/I_{rm CN})$ of $≫hbox{3000}$. When operating in standby mode for in situ long-term detection, power consumption is smaller than 0.4 $muhbox{W}$. Furthermore, the room-temperature response time is 85 s for the integrated hydrogen-sensing amplifier fabricated with a bipolar-type structure.      

A 2.4–2.5 GHz WLAN Direct-Conversion Receiver Front-End With Low-Distortion Baseband Filters

Low-distortion I/Q baseband filters interface with a 2.5 GHz RF receiver front-end configured as a Gm-cell in a direct-conversion architecture targeted towards WLAN 802.11b application. The active I/Q current-mode filters use AC current to carry the large swing of both desired and blocker signals, relaxing the voltage headroom requirement to a 1.2 V supply. An on chip master–slave automatic tuner is used to lock the filter bandwidth to a precision 20 MHz reference crystal oscillator, resulting in a $≪ ,$3% tuning accuracy and $≪, $ 0.5% I/Q bandwidth matching. The receiver achieves a 3.2 dB DSB NF, ${-}$14 dBm out-of-band IIP3, and ${+}$ 27 dBm worst case IIP2, all referred to the LNA input, while drawing 30mA from a 2.7 V supply. The chip is fabricated in a 0.5 $mu$m 46 GHz $f_{T}$ SiGe BiCMOS process. The active area is 2.54 mm$^{2}$ .      

A Linearization Technique for RF Receiver Front-End Using Second-Order-Intermodulation Injection

A linearization technique is proposed in which low-frequency second-order-intermodulation $({rm IM}_{2})$ is generated and injected to suppress the third-order intermodulation $({rm IM}_{3})$. The proposed linearization technique is applied to both a low-noise amplifier (LNA) and a down-conversion mixer in an RF receiver front-end (RFE) working at 900 MHz. Fabricated in a 0.18$ mu{hbox{m}}$ CMOS process and operated at 1.5 V supply with a total current of 13.1 mA, the RFE delivers 22 dB gain with 5.3 dB noise figure (NF). The linearization technique achieves around 20 dB ${rm IM}_{3}$ suppression and improves the RFE's ${rm IIP}_{3}$ from $-$ 10.4 dBm to 0.2 dBm without gain reduction and noise penalty while requiring only an extra current of 0.1 mA.      

A Short Range, Low Data Rate, 7.2 GHz-7.7 GHz FM-UWB Receiver Front-End

A 9 mW FM-UWB receiver front-end for low data rate ( $≪$$ hbox{50~kbps}$), short range ( $≪$$hbox{10~m}$) applications operating in the ultra-wideband (UWB) band centered at 7.45 GHz is described in this paper. A single-ended-to-differential preamplifier with 30 dB voltage gain, a 1 GHz bandwidth FM demodulator, and a combined (preamp/demodulator) receiver front-end were fabricated in 0.25 $muhbox{m}$ SiGe:C BiCMOS and characterized. Measured receiver sensitivity is $-hbox{85.8~dBm}$ while consuming 9 mW from a 1.8 V supply, and $-hbox{83~dBm}$ consuming 6 mW at 1.5 V. 15-20 m range line-of-sight in an indoor environment is realized, justifying FM-UWB as a robust radio technology for short range, low data rate applications. Multi-user and interference capabilities are also evaluated.      

Characterization and Modeling of RF-Performance $(f_{T})$ Fluctuation in MOSFETs

The fluctuation of RF performance (particularly for $f_{T}$ : cutoff frequency) in the transistors fabricated by 90-nm CMOS technology has been investigated. The modeling for $f_{T}$ fluctuation is well fitted with the measurement data within approximately 1% error. Low-$V_{t}$ transistors (fabricated by lower doping concentration in the channel) show higher $f_{T}$ fluctuation than normal transistors. Such a higher $f_{T}$ fluctuation results from $C_{rm gg}$ (total gate capacitance) variation rather than $g_{m}$ variation. More detailed analysis shows that $C_{rm gs} + C_{rm gb}$ (charges in the channel and the bulk) are predominant factors over $C_{rm gd}$ (charges in LDD/halo region) to determine $C_{rm gg}$ fluctuation.      

A Silicon-Germanium Receiver for X-Band Transmit/Receive Radar Modules

This work investigates the potential of commercially-available silicon-germanium (SiGe) BiCMOS technology for X-band transmit/receive (T/R) radar modules, focusing on the receiver section of the module. A 5-bit receiver operating from 8 to 10.7 GHz is presented, demonstrating a gain of 11 dB, and average noise figure of 4.1 dB, and an input-referred third-order intercept point $({hbox{IIP}}_{3})$ of $-$13 dBm, while only dissipating 33 mW of power. The receiver is capable of providing 32 distinct phase states from 0 to 360$^{circ}$ , with an rms phase error $≪ !{hbox{9}}^{circ}$ and an rms gain error $≪ ,$0.6 dB. This level of circuit performance and integration capability demonstrates the benefits of SiGe BiCMOS technology for emerging radar applications, making it an excellent candidate for integrated X-band phased-array radar transmit/receive modules.      

High-Speed 2$, times ,$2 Switch for Multiwavelength Silicon-Photonic Networks–On-Chip

We report the fabrication and experimental verification of a multiwavelength high-speed 2$, times ,$ 2 silicon photonic switch for ultrahigh-bandwidth message routing in optical on-chip networks. The structure employs only two microring resonators in order to implement the bar and cross states of the switch. These states are toggled using an optical pump at 1.5-$mu$m wavelengths inplane with the waveguide devices, though electronic, rather than optical, control schemes are envisioned for more complex systems built from these devices. Experiments characterize bit-error-rate performance in the bar and cross states during static and dynamic operation. The all-optical demonstration exhibits the ability of the switch to implement ultra-short transition times ( $≪ $2 ns), high extinction ratios ($>$10 dB), and low power penalties (${sim} 1$ dB) at a data rate of 10 Gb/s. Further performance improvements are expected by using electronic carrier injection via p-i-n diodes surrounding the ring waveguides. The 2$, times ,$2 switching functionality facilitates the design of more complex routing structures, allowing the implementation of high-functionality integrated optical networks.      

High-Temperature Microwave Performance of Submicron AlGaN/GaN HEMTs on SiC

The effect of temperature on the small-signal radio-frequency (RF) performance of submicron AlGaN/GaN high-electron-mobility transistors on SiC has been studied from room temperature (RT) up to 600 K. A relation between ambient and channel temperatures has been established by means of finite-element simulations. The thermal behavior of the intrinsic parameters $C_{rm gs}$, $C_{rm gd}$, $g_{m, {rm int}}$, and $g_{rm ds}$ has been extracted accurately from RF measurements by means of the small-signal equivalent circuit. Main dc parameters $(I_{D}, g_{m, {rm ext}})$ show reductions close to 50% between RT and 600 K, mainly due to the decrease in the electron mobility and drift velocity. In the same range, $f_{T}$ and $f_{max}$ suffer a 60% decrease due to the reduction in $g_{m, {rm ext}}$ and a slight increase of $C_{rm gs}$ and $C_{rm gd}$. An anomalous thermal evolution of $C_{rm gd}$ at low $I_{D}$ has been identified, which is indicative of the presence of traps.      

Performance Improvement of N-Type $hbox{TiO}_{x}$ Active-Channel TFTs Grown by Low-Temperature Plasma-Enhanced ALD

We report on performance improvement of $n$-type oxide–semiconductor thin-film transistors (TFTs) based on $hbox{TiO}_{x}$ active channels grown at 250 $^{circ}hbox{C}$ by plasma-enhanced atomic layer deposition. TFTs with as-grown $hbox{TiO}_{x}$ films exhibited the saturation mobility $(mu_{rm sat})$ as high as 3.2 $hbox{cm}^{2}/hbox{V}cdothbox{s}$ but suffered from the low on–off ratio $(I_{rm ON}/I_{rm OFF})$ of $hbox{2.0} times hbox{10}^{2}$. $hbox{N}_{2}hbox{O}$ plasma treatment was then attempted to improve $I_{rm ON}/I_{rm OFF}$. Upon treatment, the $hbox{TiO}_{x}$ TFTs exhibited $I_{rm ON}/I_{rm OFF}$ of $hbox{4.7} times hbox{10}^{5}$ and $mu_{rm sat}$ of 1.64 $hbox{cm}^{2}/hbox{V}cdothbox{s}$, showing a much improved performance balance and, thus, demonstrating their potentials for a wide variety of applications such as backplane technology in active-matrix displays and radio-frequency identification tags.      

Q-Band pHEMT and mHEMT Subharmonic Gilbert Upconversion Mixers

This letter makes a comparison between Q-band 0.15 $mu{rm m}$ pseudomorphic high electron mobility transistor (pHEMT) and metamorphic high electron mobility transistor (mHEMT) stacked-LO subharmonic upconversion mixers in terms of gain, isolation and linearity. In general, a 0.15 $mu{rm m}$ mHEMT device has a higher transconductance and cutoff frequency than a 0.15 $mu{rm m}$ pHEMT does. Thus, the conversion gain of the mHEMT is higher than that of the pHEMT in the active Gilbert mixer design. The Q-band stacked-LO subharmonic upconversion mixers using the pHEMT and mHEMT technologies have conversion gain of $-$7.1 dB and $-$0.2 dB, respectively. The pHEMT upconversion mixer has an ${rm OIP}_{3}$ of $-$12 dBm and an ${rm OP}_{1 {rm dB}}$ of $-$24 dBm, while the mHEMT one shows a 4 dB improvement on linearity for the difference between the ${rm OIP}_{3}$ and ${rm OP}_{1 {rm dB}}$. Both the chip sizes are the same at 1.3 mm $times$ 0.9 mm.      

A 3–10 GHz CMOS UWB Low-Noise Amplifier With ESD Protection Circuits

A low-power fully integrated low-noise amplifier (LNA) with an on-chip electrostatic-static discharge (ESD) protection circuit for ultra-wide band (UWB) applications is presented. With the use of a common-gate scheme with a ${rm g}_{rm m}$ -boosted technique, a simple input matching network, low noise figure (NF), and low power consumption can be achieved. Through the combination of an input matching network, an ESD clamp circuit has been designed for the proposed LNA circuit to enhance system robustness. The measured results show that the fabricated LNA can be operated over the full UWB bandwidth of 3.0 to 10.35 GHz. The input return loss $({rm S}_{11})$ and output return loss $({rm S}_{22})$ are less than ${-}8.3$ dB and ${-}9$ dB, respectively. The measured power gain $({rm S}_{21})$ is $11 pm 1.5$ dB, and the measured minimum NF is 3.3 dB at 4 GHz. The dc power dissipation is 7.2 mW from a 1.2 V supply. The chip area, including testing pads, is 1.05 mm$,times,$ 0.73 mm.      

A 10:1 Unequal Wilkinson Power Divider Using Coupled Lines With Two Shorts

A novel unequal Wilkinson power divider is presented. A coupled-line section with two shorts is proposed to realize the high characteristic impedance line, which cannot be implemented by conventional microstrip fabrication technique due to fabrication limitation. The proposed coupled-line structure is compatible with single layer integration and can be easily designed based on an even-odd mode analysis. As a design example, a 10:1 Wilkinson power divider at 2 GHz is fabricated and measured. The measured $-10~{rm dB}$ bandwidth of $S_{11}$ is about 16%, and the isolation $S_{32}$ is better than $-20~{rm dB}$ . The measured amplitude balance between output port 2 and port 3 is between $-10.20~{rm dB}$ and $-9.52~{rm dB}$, and the corresponding phase difference is between 0$^{circ}$ and 4.6$^{circ}$.      

Slope Interconnect Effort: Gate-Interconnect Interdependent Delay Modeling for Early CMOS Circuit Simulation

We propose an analytical closed-form gate-interconnect interdependent delay model that accounts for the dynamic behavior of signal slope across different regions of operation. In the presence of interconnects, the gate driver influences the input slope of the driven wire affecting the interconnect delay, and the driven wire acts as a parasitic load to the driver affecting the gate delay. Hence, it is essential to consider their interdependence for an accurate estimation of the circuit delay. The proposed model converts a signal slope into its effective fan-out for a simple yet accurate delay estimation. Simulations show that, for ISCAS benchmark circuits, our framework exhibits an error of $≪$ 5.3% at each stage and $≪$ 4.3% for the path delay with a speedup of three orders of magnitude over HSPICE at the 130-nm technology node. Two test chips have been fabricated in 90- and 65-nm CMOS technologies to verify the effectiveness of the proposed model. Measured results show that, for a wide range of interconnect lengths (2000 and 1400 ${rm mu}hbox{m}$ ) and geometries, the proposed model predicts the circuit delay with an error of 5.7% at a supply voltage of $V_{{rm dd}}=1.2 hbox{V}$ and 4.8% at $V_{{rm dd}}=0.3 hbox{V}$ .      

A 0.13 $mu$ m CMOS Quad-Band GSM/GPRS/EDGE RF Transceiver Using a Low-Noise Fractional-N Frequency Synthesizer and Direct-Conversion Architecture

This paper presents a single-chip CMOS quad-band (850/900/1800/1900 MHz) RF transceiver for GSM/GPRS/EDGE applications which adopts a direct-conversion receiver, a direct-conversion transmitter and a fractional-N frequency synthesizer with a built-in DCXO. In the GSM mode, the transmitter delivers 4 dBm of output power with 1$^{circ}$ RMS phase error and the measured phase noise is ${-}$164.5 dBc/Hz at 20 MHz offset from a 914.8$~$MHz carrier. In the EDGE mode, the TX RMS EVM is 2.4% with a 0.5 $~$dB gain step for the overall 36 dB dynamic range. The RX NF and IIP3 are 2.7 dB/ ${-}$12 dBm for the low bands (850/900 MHz) and 3 dB/${-}$ 11 dBm for the high bands (1800/1900 MHz). This transceiver is implemented in 0.13 $mu$m CMOS technology and occupies 10.5 mm$^{2}$ . The device consumes 118 mA and 84 mA in TX and RX modes from 2.8 V, respectively and is housed in a 5$,times,$ 5 mm$^{2}$ 40-pin QFN package.      

Positive Bias Temperature Instability (PBTI) Characteristics of Contact-Etch-Stop-Layer-Induced Local-Tensile-Strained $hbox{HfO}_{2}$ nMOSFET

The positive bias temperature instability (PBTI) characteristics of contact-etch-stop-layer (CESL)-strained $hbox{HfO}_{2}$ nMOSFET are thoroughly investigated. For the first time, the effects of CESL on an $hbox{HfO}_{2}$ dielectric are investigated for PBTI characteristics. A roughly 50% reduction of $V_{rm TH}$ shift can be achieved for the 300-nm CESL $hbox{HfO}_{2}$ nMOSFET after 1000-s PBTI stressing without obvious $ hbox{HfO}_{2}/hbox{Si}$ interface degradation, as demonstrated by the negligible charge pumping current increase ($≪$ 4%). In addition, the $hbox{HfO}_{2}$ film of CESL devices has a deeper trapping level (0.83 eV), indicating that most of the shallow traps (0.75 eV) in as-deposited $ hbox{HfO}_{2}$ film can be eliminated for CESL devices.      

Demonstration of Tunneling FETs Based on Highly Scalable Vertical Silicon Nanowires

This letter demonstrates a vertical silicon-nanowire (SiNW)-based tunneling field-effect transistor (TFET) using CMOS-compatible technology. With a $hbox{Si} hbox{p}^{+}{-}hbox{i}{-} hbox{n}^{+}$ tunneling junction, the TFET with a gate length of $sim$200 nm exhibits good subthreshold swing of $sim$ 70 mV/dec, superior drain-induced-barrier-lowering of $sim$ 17 mV/V, and excellent $I_{rm on} {-} I_{rm off}$ ratio of $sim!!hbox{10}^{7}$ with a low $I_{rm off} (sim!!hbox{7} hbox{pA}/muhbox{m})$. The obtained 53 $muhbox{A}/muhbox{m} I_{rm on}$ can be further enhanced with heterostructures at the tunneling interface. The vertical SiNW-based TFET is proposed to be an excellent candidate for ultralow power and high-density applications.      

A 0.55 V 60 dB-DR Fourth-Order Analog Baseband Filter

A 0.55 V supply voltage fourth-order low-pass continuous-time filter is presented. The low-voltage operating point is achieved by an improved bias circuit that uses different opamp input and output common-mode voltages. The fourth-order filter architecture is composed by two Active- ${rm G}_{rm m}{-}{rm RC}$ biquadratic cells, which use a single opamp per-cell with a unity-gain-bandwidth comparable to the filter cut-off frequency. The $-$ 3 dB filter frequency is 12 MHz and this is higher than any other low-voltage continuous-time filter cut-off frequency. The $-$3 dB frequency can be adjusted by means of a digitally-controlled capacitance array. In a standard 0.13 $mu{rm m}$ CMOS technology with ${V}_{THN}approx 0.25 {rm V}$ and ${V}_{THP}approx 0.3 {rm V}$, the filter operates with a supply voltage as low as 0.55 V. The filter $({rm total} {rm area}=0.47 {rm mm}^{2})$ consumes 3.4 mW. A 8 dBm-in-band IIP3 and a 13.3 dBm-out-of-band IIP3 demonstrate the validity of the proposal.      

High-Reflectivity Thermally Stable Ultrafast Induced Fiber Bragg Gratings in H$_{2}$ -Loaded SMF-28 Fiber

High-temperature stable high-reflectivity gratings are fabricated in hydrogen-loaded single-mode fiber (SMF-28) using ultrafast 800-nm radiation. An index modulation of $sim 9times 10^{-4}$ and a loss of $>$15 dB at the Bragg resonance is present after isochronal annealing up to 1000 $^{circ}hbox{C}$ followed by 96 h of isothermal annealing.      

A Biphase Modulator Circuit for Impulse Radio-UWB Applications

This letter presents a circuit to provide binary phase shift keying to ultra-wideband (UWB) impulse transmitters. The circuit is based on a Gilbert-cell multiplier and uses active on-chip balun and unbalanced-to-balanced converters for single-ended to single-ended operation. Detailed measurements of the circuit show a gain ripple of $pm 1~{rm dB}$ at an overall gain of $-2~{rm dB}$, an input reflection below $-12~{rm dB}$, an output reflection below $-18~{rm dB}$, a group delay variation below 6 ps and a $-1~{rm dB}$ input compression point of more than 1 dBm in both switching states over the full 3.1–10.6 GHz UWB frequency range. A time domain measurement verifies the switching operation using an FCC-compliant impulse generator. The circuit is fabricated in a $0.8~mu {rm m}$ Si/SiGe HBT technology, consumes 31.4 mA at a 3.2 V supply and has a size of $510 times 490~mu{rm m}^{2}$ , including pads. It can be used in UWB systems using pulse correlation reception or spectral spreading.      

A $Q$ -Band Four-Element Phased-Array Front-End Receiver With Integrated Wilkinson Power Combiners in 0.18-$mu{{hbox{m}}}$ SiGe BiCMOS Technology

A four-element phased-array front-end receiver based on 4-bit RF phase shifters is demonstrated in a standard 0.18- $mu{{hbox{m}}}$ SiGe BiCMOS technology for $Q$-band (30–50 GHz) satellite communications and radar applications. The phased-array receiver uses a corporate-feed approach with on-chip Wilkinson power combiners, and shows a power gain of 10.4 dB with an ${rm IIP}_{3}$ of $-$13.8 dBm per element at 38.5 GHz and a 3-dB gain bandwidth of 32.8–44 GHz. The rms gain and phase errors are $leq$1.2 dB and $leq {hbox{8.7}}^{circ}$ for all 4-bit phase states at 30–50 GHz. The beamformer also results in $leq$ 0.4 dB of rms gain mismatch and $leq {hbox{2}}^{circ}$ of rms phase mismatch between the four channels. The channel-to-channel isolation is better than $-$35 dB at 30–50 GHz. The chip consumes 118 mA from a 5-V supply voltage and overall chip size is ${hbox{1.4}}times {hbox{1.7}} {{hbox{mm}}}^{2}$ including all pads and CMOS control electronics.