互联网流量的结构特性:重叠社团和相关性(英文)

There is an increasing number of Internet applications, which leads to an increasing network capacity and availability. Internet traffic characterisation and application identification are, therefore, more important for efficient network management. In this paper, we construct flow graphs from detailed Internet traffic data collected from the public networks of Internet Service Providers. We analyse the community structures of the flow graph that is naturally formed by different applications. The community size, degree distribution of the community, and community overlap of 10 Internet applications are investigated. We further study the correlations between the communities from different applications. Our results provide deep insights into the behaviour Internet applications and traffic, which is helpful for both network management and user behaviour analysis.     

Research on Value Assessment-Based Accurate Identification of Government and Corporate Customers of Telecom Operators

Aiming at discovering target customers, this article establishes the value assessment system for government ＆ corporate customers according to the level, stability and accessibility of customer value. With 137 customers as samples, it builds the government ＆ corporate customer value assessment system through analytic hierarchy process （AHP） and identifies target government ＆corpora te customers by indicator optimization, model fitting and cluster analysis. All these achievements help accurate identification of high-value government and corporate customers and optimization of resource allocation for customer service.     

基于非线性DAC的高速直接数字频率合成器

This paper presents a high speed ROM-less direct digital frequency synthesizer （DDFS） which has a phase resolution of 32 bits and a magnitude resolution of 10 bits. A 10-bit nonlinear segmented DAC is used in place of the ROM look-up table for phase-to-sine amplitude conversion and the linear DAC in a conventional DDFS. The design procedure for implementing the nonlinear DAC is presented. To ensure high speed, current mode logic （CML） is used. The chip is implemented in Chartered 0.35μm COMS technology with active area of 2.0 × 2.5 mm^2 and total power consumption of 400 mW at a single 3.3 V supply voltage. The maximum operating frequency is 850 MHz at room temperature and 1.0 GHz at 0℃.     

一种适用于“模一”多带OFDM超宽带系统中跳频产生的3.96GHz锁相环

A fully integrated phase-locked loop（PLL） is presented for a single quadrature output frequency of 3.96 GHz.The proposed PLL can be applied to mode-1 MB-OFDM UWB hopping carrier generation.An adaptive frequency calibration loop is incorporated into the PLL.The capacitance area in the loop filter is largely reduced through a capacitor multiplier.Implemented in a CMOS process, this PLL draws 13.0 mA current from a single 1.2 V supply while occupying 0.55 mm2 die area.Measurement results show that the PLL achieves a phase noise of-70 dBc/Hz at 10 kHz offset and-113 dBc/Hz at 1 MHz offset.The integrated RMS jitter from 1 kHz to 10 MHz is 2.2 ps.The reference spur level is less than-68 dBc.     

具有频率调谐的GNSS接收机双模复数滤波器

A fifth/seventh order dual-mode OTA-C complex filter for global navigation satellite system receivers is implemented in a 0.18μm CMOS process.This filter can be configured as the narrow mode of a 4.4 MHz bandwidth center at 4.1 MHz or the wide mode of a 22 MHz bandwidth center at 15.42 MHz.A fully differential OTA with source degeneration is used to provide sufficient linearity.Furthermore,a ring CCO based frequency tuning scheme is proposed to reduce frequency variation.The measured results show that in narrow-band mode the image rejection ratio（IMRR）is 35 dB,the filter dissipates 0.8 mA from the 1.8 V power supply,and the out-of-band rejection is 50 dB at 6 MHz offset.In wide-band mode,IMRR is 28 dB and the filter dissipates 3.2 mA.The frequency tuning error is less than±2%.     

应用于低中频和零中频DVB调谐器中8阶信道滤波器设计

An eighth order active-RC filter for low-IF and zero-IF DVB tuner applications is presented, which is implemented in Butterworth biquad structure. An automatic frequency tuning circuit is introduced to compensate the cut-off frequency variation using a 6-bit switched-capacitor array. Switched-resistor arrays are adopted to cover different cut-off frequencies in low-IF and zero-IF modes. Measurement results show that precise cut-off frequencies at 2.5, 3, 3.5 and 4 MHz in zero-IF mode, 5, 6, 7 and 8 MHz in low-IF mode can be achieved, 60 dB frequency attenuation can be obtained at 20 MHz, and the in-band group delay agrees well with the simulation. Two-tone testing shows the in-band IM3 achieves -52 dB and the out-band IM3 achieves -55 dB with -11 dBm input power. This proposed filter circuit, fabricated in a SMIC 0.18μm CMOS process, consumes 4 mA current with 1.8 V power supply.     

A 3.1-4.8 GHz transmitter with a high frequency divider in 0.18μm CMOS for OFDM-UWB

A fully integrated low power RF transmitter for a WiMedia 3.1-4.8 GHz multiband orthogonal frequency division multiplexing ultra-wideband system is presented. With a separate transconductance stage, the quadrature up-conversion modulator achieves high linearity with low supply voltage. The co-design of different resonant frequencies of the modulator and the differential to single （D2S） converter ensures in-band gain flatness. By means of a series inductor peaking technique, the D2S converter obtains 9 dB more gain without extra power consumption. A divided-by-2 divider is used for carrier signal generation. The measurement results show an output power between -10.7 and -3.1 dBm with 7.6 dB control range, an OIP3 up to 12 dBm, a sideband rejection of 35 dBc and a carrier rejection of 30 dBc. The ESD protected chip is fabricated in the Jazz 0.18μm RF CMOS process with an area of 1.74 mm^2 and only consumes 32 mA current （at 1.8 V） including the test associated parts.     

一种适用于多带OFDM超宽带系统中的快速跳频3子带CMOS频率综合器

A fast-hopping 3-band （mode 1） multi-band orthogonal frequency division multiplexing ultra-wideband frequency synthesizer is presented. This synthesizer uses two phase-locked loops for generating steady frequencies and one quadrature single-sideband mixer for frequency shifting and quadrature frequency generation. The generated carriers can hop among 3432 MHz, 3960 MHz, and 4488 MHz. Implemented in a 0.13 μm CMOS process, this fully integrated synthesizer consumes 27 mA current from a 1.2 V supply. Measurement shows that the out-of-band spurious tones are below -50 dBc, while the in-band spurious tones are below -34 dBc. The measured hopping time is below 2 ns. The core die area is 1.0 ×1.8 mm^2.     

Does Amplify-and-Forward Cooperative Relay Improve OFDM/OFDMA Ergodic Capacity？

The ergodic information rate for Orthogonal Frequency-Division Multiplexing / Orthogonal Frequency-Division Multiple Access with amplify-and-forward （AF） relaying systems in the presence of frequency offsets is evaluated. Unlike previous work, per-subcarrier adaptive power allocation is performed on each relay to optimize the system ergodic information rate. For a given frequency offset and total number of relays M, the AF ergodic information rate is proven to be a monotonically increasing function of α （the ratio of the power allocated to the source node and the total transmit power）, implying that the maximum ergodic information rate can be obtained at α=1 （i.e., there is no cooperative relay）. Furthermore, the proof of ＂cooperative relays cannot improve the AF ergodic information rate in a quasi-static wireless channel＂ is also provided in this letter.     

A power scalable PLL frequency synthesizer for high-speed △-∑ ADC

A 35-130 MHz/300-360 MHz phase-locked loop frequency synthesizer for △-∑ analog-to-digital con- verter （ADC） in 65 nm CMOS is presented. The frequency synthesizer can work in low phase-noise mode （300-360 MHz） or in low-power mode （35-130 MHz） to satisfy the ADC＇s requirements. To switch between these two modes, a high frequency GHz LC VCO followed by a divided-by-four frequency divider and a low frequency ring VCO followed by a divided-by-two frequency divider are integrated on-chip. The measured results show that the fre- quency synthesizer achieves a phase-noise of-132 dBc/Hz at 1 MHz offset and an integrated RMS jitter of 1.12 ps with 1.74 mW power consumption from a 1.2 V power supply in low phase-noise mode. In low-power mode, the frequency synthesizer achieves a phase-noise of-112 dBc/Hz at 1 MHz offset and an integrated RMS jitter of 7.23 ps with 0.92 mW power consumption from a 1.2 V power supply.     

Software Radio——Software Radio： A Review of Design Considerations and Digital Hardware Choices

This paper reviews the requirements for Software Defined Radio （SDR） systems for high-speed wireless applications and compares how well the different technology choices available- from ASICs, FPGAs to digital signal processors （DSPs） and general purpose processors （GPPs） - meet them.     

EEFA： Energy Efficiency Frame Aggregation Scheduling Algorithm for IEEE 802.11n Wireless Network

Packet size is restricted due to the error-prone wireless channel which drops the network energy utilization. Furthermore, the frequent packet retransmissions also lead to energy waste. In order to improve the energy efficiency of wireless networks and save the energy of wireless devices, EEFA （Energy Efficiency Frame Aggregation）, a frame aggregation based energy-efficient scheduling algorithm for IEEE 802.11n wireless network, is proposed. EEFA changes the size of aggregated frame dynamically according to the frame error rate, so as to ensure the data transmission and retransmissions completed during the TXOP and reduce energy consumption of channel contention. NS2 simulation results show that EEFA algorithm achieves better performance than the original frame-aggregation algorithm.     

适用于OFDM UWB 系统的低功耗，大锁定范围注入锁定分频器

This paper describes a divide-by-two injection-locked frequency divider （ILFD） for frequency synthesizers as used in multiband orthogonal frequency division multiplexing （OFDM） ultra-wideband （UWB） systems. By means of dual-injection technique and other conventional tuning techniques, such as DCCA and varactor tuning, the divider demonstrates a wide locking range while consuming much less power. The chip was fabricated in the Jazz 0.18μm RF CMOS process. The measurement results show that the divider achieves a locking range of 4.85 GHz （6.23 to 11.08 GHz） at an input power of 8 dBm. The core circuit without the test buffer consumes only 3.7 mA from a 1.8 V power supply and has a die area of 0.38×0.28 mm^2. The wide locking range combined with low power consumption makes the ILFD suitable for its application in UWB systems.     

SDN-Based Data Offioading for 5G Mobile Networks

The rapid growth of 3G/4G enabled devices such as smartphones and tablets in large numbers has created increased demand formobile data services.Wi-Fi offloading helps satisfy the requirements of data-rich applications and terminals with improved multi-media.Wi-Fi is an essential approach to alleviating mobile data traffic load on a cellular network because it provides extra capaci-ty and improves overall performance.In this paper,we propose an integrated LTE/Wi-Fi architecture with software-defined net-working(SDN)abstraction in mobile backhaul and enhanced components that facilitate the move towards next-generation 5G mo-bile networks.Our proposed architecture enables programmable offloading policies that take into account real-time network condi-tions as well as the status of devices and applications.This mechanism improves overall network performance by deriving real-time policies and steering traffic between cellular and Wi-Fi networks more efficiently.     

应力和电阻率可控的适用于高品质因子MEMS器件的原位掺硼LPCVD多晶硅薄膜

The simultaneous control of residual stress and resistivity of polysilicon thin films by adjusting the deposition parameters and annealing conditions is studied. In situ boron doped polysilicon thin films deposited at 520 ℃ by low pressure chemical vapor deposition （LPCVD） are amorphous with relatively large compressive residual stress and high resistivity. Annealing the amorphous films in a temperature range of 600-800 ℃ gives polysilicon films nearly zero-stress and relatively low resistivity. The low residual stress and low resistivity make the polysilicon films attractive for potential applications in micro-electro-mechanical-systems （MEMS） devices, especially in high resonance frequency （high-f） and high quality factor （high-Q） MEMS resonators. In addition, polysilicon thin films deposited at 570 ℃ and those without the post annealing process have low resistivities of 2-5 mΩ·cm. These reported approaches avoid the high temperature annealing process （〉 1000 ℃）, and the promising properties of these films make them suitable for high-Q and high-f MEMS devices.     

A low power 3-5 GHz CMOS UWB receiver front-end

A novel low power RF receiver front-end for 3-5 GHz UWB is presented. Designed in the 0.13μm CMOS process, the direct conversion receiver features a wideband balun-coupled noise cancelling transconductance input stage, followed by quadrature passive mixers and transimpedance loading amplifiers. Measurement results show that the receiver achieves an input return loss below -8.5 dB across the 3.1-4.7 GHz frequency range, maximum voltage conversion gain of 27 dB, minimum noise figure of 4 dB, IIP3 of -11.5 dBm, and IIP2 of 33 dBm. Working under 1.2 V supply voltage, the receiver consumes total current of 18 mA including 10 mA by on-chip quadrature LO signal generation and buffer circuits. The chip area with pads is 1.1 × 1.5 mm^2.     

适用于双金属栅集成的TaN湿法腐蚀

Wet-etch etchants and the TaN film method for dual-metal-gate integration are investigated. Both HF/HN O3/H2O and NH4OH/H2O2 solutions can etch TaN effectively, but poor selectivity to the gate dielectric for the HF/HNO3/H2O solution due to HF being included in HF/HNO3/H2O, and the fact that TaN is difficult to etch in the NH4OH/H2O2 solution at the first stage due to the thin TaOxNy layer on the TaN surface, mean that they are difficult to individually apply to dual-metal-gate integration. A two-step wet etching strategy using the HF/HNO3/H2O solution first and the NH4OH/H2O2 solution later can fully remove thin TaN film with a photo-resist mask and has high selectivity to the HfSiON dielectric film underneath. High-k dielectric film surfaces are smooth after wet etching of the TaN metal gate and MOSCAPs show well-behaved C-V and Jg-Vg characteristics, which all prove that the wet etching of TaN has little impact on electrical performance and can be applied to dual-metal-gate integration technology for removing the first TaN metal gate in the PMOS region.     

一种应用于频率综合器的全差分电荷泵的设计与噪声分析

A fully-differential charge pump（FDCP）with perfect current matching and low output current noise is realized for phase-locked loops（PLLs）.An easily stable common-mode feedback（CMFB）circuit which can handle high input voltage swing is proposed.Current mismatch and current noise contribution from the CMFB circuit is minimized.In order to optimize PLL phase noise,the output current noise of the FDCP is analyzed in detail and calculated with the sampling principle.The calculation result agrees well with the simulation.Based on the noise analysis,many methods to lower output current noise of the FDCP are discussed.The fully-differential charge pump is integrated into a 1–2 GHz frequency synthesizer and fabricated in an SMIC CMOS 0.18μm process.The measured output reference spur is–64 dBc to–69 dBc.The in-band and out-band phase noise is–95 dBc/Hz at 3 kHz frequency offset and–123 dBc/Hz at 1 MHz frequency offset respectively.     

Software-Defined Cellular Mobile Network Solutions

The emergency relating to software-defined networking(SDN),especially in terms of the prototype associated with OpenFlow,pro-vides new possibilities for innovating on network design.Researchers have started to extend SDN to cellular networks.Such newprogrammable architecture is beneficial to the evolution of mobile networks and allows operators to provide better services.Thetypical cellular network comprises radio access network(RAN)and core network(CN);hence,the technique roadmap diverges intwo ways.In this paper,we investigate SoftRAN,the latest SDN solution for RAN,and SoftCell and MobileFlow,the latest solu-tions for CN.We also define a series of control functions for CROWD.Unlike in the other literature,we emphasize only software-defined cellular network solutions and specifications in order to provide possible research directions.     

基于代数签名且支持数据动态更新的云数据完整性验证方案(英文)

Cloud storage is one of the main application of the cloud computing. With the data services in the cloud, users is able to outsource their data to the cloud, access and share their outsourced data from the cloud server anywhere and anytime. However, this new paradigm of data outsourcing services also introduces new security challenges, among which is how to ensure the integrity of the outsourced data. Although the cloud storage providers commit a reliable and secure environment to users, the integrity of data can still be damaged owing to the carelessness of humans and failures of hardwares/softwares or the attacks from external adversaries. Therefore, it is of great importance for users to audit the integrity of their data outsourced to the cloud. In this paper, we first design an auditing framework for cloud storage and proposed an algebraic signature based remote data possession checking protocol, which allows a third-party to auditing the integrity of the outsourced data on behalf of the users and supports unlimited number of verifications. Then we extends our auditing protocol to support data dynamic operations, including data update, data insertion and data deletion. The analysis and experiment results demonstrate that our proposed schemes are secure and efficient.