茶渣吸附U(Ⅵ)的特性

通过静态吸附实验,考察了铀溶液初始pH、初始浓度以及吸附时间、吸附剂粒度、温度对茶渣吸附U(Ⅵ)的影响,分析了吸附过程的动力学行为及等温吸附特性,并通过红外光谱和扫描电镜探讨了吸附机理。结果表明:pH对茶渣吸附U(Ⅵ)的影响较大,pH为2和6时吸附量分别为13.90、43.19 mg·g^-1。茶渣吸附U(Ⅵ)的过程较慢,吸附过程需要12 h才能达到平衡。吸附过程的准二级动力学方程的拟合效果优于准一级动力学方程。吸附量随铀溶液浓度的增加而增大,而吸附率则相反。铀溶液初始浓度为10~100 mg·L^-1,相应的吸附量为9.40~70.05 mg·g^-1,吸附率为94.04%~70.05%。茶渣吸附U(Ⅵ)的动力学行为更符合准二级动力学方程,等温吸附数据对Freundlich方程的拟合度较高。茶渣粒度及温度对茶渣吸附U(Ⅵ)的影响不大。茶渣吸附U(Ⅵ)的过程中,起主要作用的基团有羟基、羰基、硝基、P-O、Si-O。     

Adsorption characteristics of U(Ⅵ)on tea waste

通过静态吸附实验,考察了铀溶液初始pH、初始浓度以及吸附时间、吸附剂粒度、温度对茶渣吸附U(Ⅵ)的影响,分析了吸附过程的动力学行为及等温吸附特性,并通过红外光谱和扫描电镜探讨了吸附机理。结果表明:pH对茶渣吸附U(Ⅵ)的影响较大,pH为2和6时吸附量分别为13.90、43.19 mg·g^-1。茶渣吸附U(Ⅵ)的过程较慢,吸附过程需要12 h才能达到平衡。吸附过程的准二级动力学方程的拟合效果优于准一级动力学方程。吸附量随铀溶液浓度的增加而增大,而吸附率则相反。铀溶液初始浓度为10~100 mg·L^-1,相应的吸附量为9.40~70.05 mg·g^-1,吸附率为94.04%~70.05%。茶渣吸附U(Ⅵ)的动力学行为更符合准二级动力学方程,等温吸附数据对Freundlich方程的拟合度较高。茶渣粒度及温度对茶渣吸附U(Ⅵ)的影响不大。茶渣吸附U(Ⅵ)的过程中,起主要作用的基团有羟基、羰基、硝基、P—O、Si—O。     

Adsorption of uranium from sulfate leach liquor using rice straw impregnated with chlorophenyl hydrazinyl pyrazoloquinazolinon

The impregnation of rice straw with 2-amino-3-(2-(4-chlorophenyl)hydrazinyl)-8,8-dimethyl-8,9-dihydropyrazolo[1,5-a]quinazolin-6(7H)-one (CPHPQ) has been used for the recovery of uranium from sulfate leach liquor. The uranium adsorption and elution of solvent impregnated mercerized rice straw (SIMRS) were carried out using a batch technique. The uranium adsorption controlling factors include pH, initial uranium concentration, contact time, S/L ratio, and temperature. Thermodynamic characteristics showed that the adsorption process is exothermic with enthalpy change ΔH = ?152.1 kJ/mol. The kinetics data fit well with a pseudo-second-order model. The equilibrium data fit well with the Langmuir isotherm. Uranium cake was obtained from the eluate solution using hydrogen peroxide as UO₄.2H₂O precipitate.     

短孔道介孔二氧化硅SBA-15对铀的吸附性能

以短孔道介孔二氧化硅SBA-15为铀吸附剂,考察吸附时间、初始液pH、初始浓度对吸附性能的影响,并分析了吸附动力学和吸附等温线以及吸附前后红外光谱变化。结果表明,初始液pH对吸附具有重要的影响,最佳吸附的pH值为6; 吸附在30 min即可达到平衡; 当初始浓度为100 mg·L^-1时,饱和吸附量为311 mg·g^-1;吸附量随铀溶液初始浓度的增大而增大,而吸附百分数则相反;吸附等温线符合Langmuir和Freundlich吸附模型,吸附动力学符合准二级动力学方程;吸附过程中起主要作用的基团是Si-OH和Si-O-Si。     

Synthesis and Anti-Candida Activity of Cobalt(II) Complexes of Benzene-1,2-Dioxyacetic Acid (bdoaH(2)). X-Ray Crystal Structures of [Co(bdoa)(H(2)O)(3)] 3.5H(2)O and {[CO(phen)(3)](bdoa)}(2)24H(2)O (phen = 1,10-Phenanthroline)

Co(CH(3)CO(2))(2)4H(2)O reacts with benzene-1,2-dioxyacetic acid (bdoaH(2)) to give the Co(2+) complexes [Co(bdoa)(H(2)O)(3)]H(2)O (1a) and [Co(bdoa)(H(2)O)(3)] 3.5H(2)O (1b). Subsequent reaction of 1a with 1,10- phenanthroline produces [CO(phen)(3)] bdoa10H(2)O (2a) and {[CO(phen)(3)](bdoa)}(2)24H(2)O (2b). Molecular structures of 1b and 2b were determined crystallographically. In 1b the bdoa(2-)- ligates the metal by two carboxylate oxygens and two ethereal oxygens, whereas in 2b the bdoa(2-) is uncoordinated. The Mn(2+) and Cu(2+) complexes [Mn(bdoa)(phen)(2)]H(2)O (3) and [Cu(pdoa)(imid)(2)] (4) were also synthesised, 1a-4 and other metal complexes of bdoa H(2) (metal = Mn(2+), Co(2+) ,Cu(2+), Cu(+) ) were screened for their ability to inhibit the growth ofhe yeast Candida albicans. Complexes incorporating the 1,10-phenanthroline ligand were the most active.     

四种生物吸附剂对铀的吸附性能研究

以保护环境为目的,以寻求廉价而有效的生物吸附材料为出发点,研究了啤酒酵母菌、北海海草、榕树叶、杉树皮等4种吸附剂对铀的吸附性能的影响。结果表明:4种吸附剂对低浓度铀具有很好的富集作用,其吸附率都在99%以上;每种吸附剂都存在1个最适pH值和1个最佳投放质量浓度,依次对应为4.0—5.0,4—4.5,3.5—4.0,3.0—4.0和10,12,8,10 g/L;4种生物吸附剂对铀吸附符合Freundlich和Langmuir吸附等温方程,且吻合良好;另外4种吸附剂对铀的吸附在吸附量之间存在较大差别,在同一平衡浓度下,吸附量大小顺序为:啤酒酵母菌>榕树叶>北海海草>杉树皮。     

Adsorption of anionic dyes on poly(epicholorohydrin dimethylamine) modified bentonite in single and mixed dye solutions

The performance of poly(epicholorohydrin dimethylamine) modified bentonite (EPIDMA/bentonite) as an adsorbent to remove anionic dyes, namely Direct Fast Scarlet, Eosin Y and Reactive Violet K-3R, was investigated in single, binary and ternary dye systems. In adsorption experiments in single dye solutions, the adsorption of the three dyes onto EPIDMA/bentonite was described by the Langmuir isotherm model and the pseudo-second-order kinetic model. At low dosage of EPIDMA/bentonite, preferential adsorption was observed for the dye with higher affinity to the adsorbent in mixed dye systems. The reduction in uptake of the dye with increasing equilibrium dye concentration in the isotherm and desorption in the kinetic curves were observed for the dye with lower affinity. The total amount of dyes adsorbed versus the total equilibrium dye concentrations were fitted well by the Langmuir isotherm model. The kinetics of the total adsorbed amount of dyes followed the pseudo-second-order kinetic model. The effect of the dosage of adsorbent on color removal efficiency, residual color distribution and adsorption kinetics was investigated.     

针状微胶囊Mg(OH)_2/EVA纳米复合材料的制备及性能研究

将自制针状微胶囊纳米氢氧化(镁Mg(OH)2)与乙烯-乙酸乙烯共聚(物EVA)经双螺杆挤出机熔融共混挤出造粒,然后利用注射机制成针状微胶囊Mg(OH)2/EVA纳米复合材料,对其力学性能、热稳定性和流变性能进行了研究。结果表明:纳米Mg(OH)2用量为4%时,复合材料的拉伸强度最大,加工流动性较好;在低温区时,纳米Mg(OH)2含量对复合材料的热稳定性能几乎没有影响,在高温区时,纳米Mg(OH)2的加入使其热稳定性略有提高。     

Al（OH）3胶体的制备及其对铀的吸附机理

为了研究在地浸采铀中胶体对矿层的阻塞及对铀酰离子吸附迁移影响,采用硝酸铝与氨水为原料制备Al（OH）₃,并用在pH = 6条件下制备所得的Al（OH）₃对铀进行吸附实验研究,考察了吸附的pH值、初始浓度及吸附时间等对Al（OH）₃吸附铀的影响。对实验数据使用准一级、复合二级与Elovich 动力学模型进行计算与分析,得出Elovich 动力学方程更适合描述Al（OH）₃对铀吸附,吸附主要是表面吸附;使用 Freundlich与Langmuir等温吸附方程对实验数据进行拟合,结果表明Langmuir模型更适合描述Al（OH）₃对铀酰离子的吸附;对吸附前、后的Al（OH）₃进行SEM与激光粒度分析。     

应用光谱分析技术研究榕树叶吸附铀的机理

为了了解榕树叶吸附铀的过程机制,改善榕树叶吸附能力,提高铀的去除率,采用红外光谱仪、扫描电镜仪、X射线衍射仪、X射线光电子能谱仪等现代分析仪器探讨榕树叶吸附铀的机理。结果表明:榕树叶主要由碳水化合物、木质素及纤维素等组成,其吸收峰是由C=O的伸缩振动峰、苯环的骨架振动峰、苯羟基中C—O的伸缩振动峰构成;吸附UO22+后,榕树叶细胞的表面形态发生了改变,表面上分布的空隙和空洞减少,呈现出较多电子不透明的微小颗粒,相互黏合在一起,但没有形成新晶形结构,只是吸附过程中部分晶相转变为非晶相,其基本结构仍保持完整;因此榕树叶吸附铀的机理为表面络合吸附机理,UO22+主要与细胞表面上—OH、C=O、P—O及Si=O等基团螯合,形成配合物。     

Syntheses and characterization of new nickel coordination polymers with 4,4'-dipyridylsulfide. Dynamic rearrangements of one-dimensional chains responding to external stimuli: temperature variation and guest releases/re-inclusions

Crystal structures and dynamic rearrangements of one-dimensional coordination polymers with 4,4'-dipyridylsulfide (dps) have been studied. Reaction of Ni(NO(3))(2)·6H(2)O with dps in EtOH yielded [Ni(dps)(2)(NO(3))(2)] ·EtOH (1), which had channels filled with guest EtOH molecules among the four Ni(dps)(2) chains. This coordination polymer reversibly transformed the channel structure responding to temperature variations. Immersion of 1 in m-xylene released guest EtOH molecules to yield a guest-free coordination polymer [Ni(dps)(2)(NO(3))(2)] (2a), which was also obtained by treatment of Ni(NO(3))(2)·6H(2)O with dps in MeOH. On the other hand, removal of the guest molecules from 1 upon heating at 130 °C under reduced pressure produced a guest-free coordination polymer [Ni(dps)(2)(NO(3))(2)] (2b). Although the 2a and 2b guest-free coordination polymers have the same formula, they showed differences in the assembled structures of the one-dimensional chains. Exposure of 2b to EtOH vapor reproduced 1, while 2a did not convert to 1 in a similar reaction. Reaction of Ni(NO(3))(2)·6H(2)O with dps in acetone provided [Ni(dps)(NO(3))(2)(H(2)O)] ·Me(2)CO (4) with no channel structure. When MeOH or acetone was used as a reaction solvent, the [Ni(dps)(2)(NO(3))(2)] · (guest molecule) type coordination polymer, which was observed in 1, was not formed. Nevertheless, the reaction of Ni(NO(3))(2)·6H(2)O with dps in MeOH/acetone mixed solution produced [Ni(dps)(2)(NO(3))(2)]·0.5(MeOH·acetone) (5), which has an isostructural Ni-dps framework to 1.     

Nano-Mg(OH)2 platelets coated flexible polyurethane foam for fast and environment-friendly removal of Cu2+ from aqueous solution

In this study, flexible polyurethane foam (FPUF) was successfully coated with nano-Mg(OH)₂ platelets. Due to the strong interaction between chitosan and nano-Mg(OH)₂, it was possible to yield modified foam with a weight-gain of up to 15 wt% by depositing one chitosan layer and one nano-Mg(OH)₂ layer. Meanwhile, the adsorption isotherms of Cu²⁺ on FPUF covered with 10 wt% coating (FPUF-10) shows the Langmuir behavior. It was found that for the FPUF-10, the removal % for Cu²⁺ after 30 min and 50 min treatment were 86% and 90%, respectively. Moreover, the maximum removal % could reach up to 95%.     

胶原纤维负载锆对氟离子和磷酸根的吸附去除

将Zr(Ⅳ)负载在胶原纤维基质上制备吸附材料,研究了该吸附材料对水溶液中氟离子和磷酸根离子的吸附特性。结果表明,胶原纤维负载Zr(Ⅳ)(ZrCF)对氟离子和磷酸根离子均有较强的吸附能力,在pH=4～9,胶原纤维负载Zr(Ⅳ)对氟离子保持较高的吸附容量;ZrCF吸附磷酸根的适宜pH=3.0～6.0。胶原纤维负载Zr(Ⅳ)对氟离子和磷酸根离子的吸附等温线均符合Langmuir方程;吸附动力学研究表明,胶原纤维负载Zr(Ⅳ)对氟离子和磷酸根离子的吸附动力学可以用准二级速率方程来描述。水中常见的Cl-、NO3-、CO23-和SO24-对ZrCF吸附氟离子和磷酸根离子的影响不大,模拟地下水体系的动态实验结果表明,ZrCF对磷酸根的亲和力更强。     

纤维素亲和膜对木瓜蛋白酶的吸附特性

以纤维素滤纸膜为载体,染料汽巴蓝F3GA为配基,制备出一种新型亲和膜色谱介质。分别在277,298,310K的均衡实验条件下,批量法对木瓜蛋白酶进行等温吸附测定。所得的数据用准一级动力学模型和准二级动力学模型进行分析。结果表明:准二级动力学模型具有更好的相关性,纤维素染料亲和膜对木瓜蛋白酶的吸附符合Lang-muir吸附模型,在298K条件下吸附现象的热力学参数:ΔGΘ,ΔHΘ,ΔSΘ分别为-7.71kJ/mol,34.91kJ/mol和0.143kJ/(mol.K),染料纤维素亲和膜对木瓜蛋白酶的吸附是自发的,并且是吸热过程。     

羟基锡酸锌包覆纳米氢氧化镁在PVC中的应用

通过均匀沉淀法制备了羟基锡酸锌包覆纳米氢氧化镁并将其应用到聚氯乙烯(PVC)中。利用XRD、TG、DTA对羟基锡酸锌包覆纳米氢氧化镁的性能进行了研究,并通过氧指数、烟密度研究了羟基锡酸锌包覆纳米氢氧化镁对PVC的阻燃和抑烟性能的影响,同时对其力学性能也进行了研究。结果表明:纳米氢氧化镁表面均匀地包覆了羟基锡酸锌;羟基锡酸锌包覆纳米氢氧化镁对PVC的阻燃和抑烟性能明显优于单独添加羟基锡酸锌、纳米氢氧化镁以及羟基锡酸锌包覆微米氢氧化镁和羟基锡酸锌与纳米氢氧化镁混和物时的阻燃、抑烟性能;纳米材料的加入对PVC的力学性能也产生了有利的影响。     

Interaction of [Rh(2)(O(2)CCH(3))(4)(H(2)O)(2)] and [Rh(2)(O(2)CCH(OH)Ph)(2)(phen)(2)(H(2)O)(2)](O(2)C-CH(OH)Ph)(2) With Sulfhydryl Compounds and Ceruloplasmin

The interaction of binuclear rhodium(II) complexes [Rh(2)(OOCCH(3))(4)(H(2)O)(2)], [Rh(2){OOCCH(OH)Ph}(2)(phen)(2)(H(2)O)(2)] {OOCCH(OH)Ph}(2), [Rh(2)(OOCCH(3))(2)(bpy)(2)(H(2)O)(2)](OOCCH(3))(2) and [Rh(2)Cl(2)(OOCMe)(2)(bpy)(2)](3H(2)O) with ceruloplasmin, cysteine, glutathione and coenzyme A have been investigated using. UV-Vis and CD spectroscopies. The complexes containing phen or bpy at pH = 7.4 and 4.0 are readily reduced with sulfhydryl compounds, while rhodium(II) acetate is relatively stable in these conditions. Complex [Rh(2){OOCCH(OH)Ph}(2)(phen)(2)(H(2)O)(2)] strongly changes structure of ceruloplasmin leading to the decrease of of alpha-helix content and loss of oxidase activity.     

纳米聚丙烯酸酯改性纳米Mg(OH)_2及其在LDPE中的应用

采用纳米聚丙烯酸酯乳液改性纳米Mg(OH)2,通过单螺杆挤出机制备了纳米Mg(OH)2/低密度聚乙烯(LDPE)复合材料,利用红外光谱、扫描电镜、透射电镜等方法对改性前后的Mg(OH)2及Mg(OH)2/LDPE复合材料进行了表征。结果表明:纳米Mg(OH)2表面经纳米聚丙烯酸酯乳液改性后吸附上了一层聚丙烯酸酯;纳米聚丙烯酸酯乳液改性提高了纳米Mg(OH)2的热稳定性,分解温度提高了27℃;改性纳米Mg(OH)2在LDPE基体中分散更为均匀;改性纳米Mg(OH)2的用量为LDPE的15%时复,合材料的拉伸强度比纯LDPE提高了6.5%。     

Friedel盐对废水中低浓度Cd2+的吸附动力学

以合成的Friedel盐(FS, 3CaO×A12O3×CaCl2×10H2O)为吸附剂,研究了FS去除废水中Cd2+的反应动力学和等温吸附特性. 考察了FS盐用量、温度及Cd2+初始浓度对Cd2+去除的影响. 结果表明,FS用量为0.03 g/L时,在室温下对废水中初始浓度为10 mg/L的Cd2+的去除率大于94.34%,吸附容量可达301.9 mg/g,吸附主要以离子交换吸附为主,最终形成Cd4Al2(OH)12Cl2(H2O)4×xH2O及Cd4Al2(OH)12Cl2×4H2O化合物. 利用一级动力学模型关联了反应动力学数据,得到速率常数k=0.049 min-1,吸附行为较符合Langmuir等温吸附方程.     

Extent of the Acidification by N7-Coordinated cis-Diammine-Platinum(II) on the Acidic Sites of Guanine Derivatives

Coordination of two monoprotonated 2'-deoxyguanosine 5'-monophosphate species, H(dGMP)(-), via N7 to cis-(NH(2))(2)Pt(2+) gives the complex cis-(NH(2))(2)Pt(H.dGMP)(2) which is a four-protonic acid. The corresponding acidity constants were measured by potentiometric pH titrations (25; I = 0.1 M, NaNO(3)). The first two protons are released from the two -P(O)(2)(OH)(-) groups (PK(a/1)= 5.57; PK(a/2) = 6.29) and the next two protons are from the H(N1) sites of the guanine residues (PK(a/3) = 8.73; PK(a/4) = 9.48). The micro acidity constants of the various sites are also evaluated. Comparison of these data with those determined for the three-protonic H(2)(dGMP)(+/-) (PK(a/1) = 2.69 for the H(+)(N7) site; PK(a/2) = 6.29 for -P(O)(2)(OH)(-) ;PK(a/3) = 9.56 for H(N1)) shows that on average the N-7-coordinated Pt(2+) acidifies the phosphate protons by Delta pK(a) = 0.36 and the H(N1) sites by Delta pK(a) = 0.46. These results are further compared with those obtained previously for cis-(NH(2))(2)Pt(L)(2), where L = 9-ethylguanine or monoprotonated 2'-deoxycytidine 5'-monophosphate. Conclusions regarding platinated DNA are also presented.