A time-delay jitter-insensitive continuous-time bandpass /spl Delta//spl Sigma/ modulator architecture

In this paper, we present a new continuous-time bandpass delta-sigma (/spl Delta//spl Sigma/) modulator architecture with mixer inside the feedback loop. The proposed bandpass /spl Delta//spl Sigma/ modulator is insensitive to time-delay jitter in the digital-to-analog conversion feedback pulse, unlike conventional continuous-time bandpass /spl Delta//spl Sigma/ modulators. The sampling frequency of the proposed /spl Delta//spl Sigma/ modulator can be less than the center frequency of the input narrow-band signal.     

A time-interleaved continuous-time /spl Delta//spl Sigma/ modulator with 20-MHz signal bandwidth

This paper presents the first implementation results for a time-interleaved continuous-time /spl Delta//spl Sigma/ modulator. The derivation of the time-interleaved continuous-time /spl Delta//spl Sigma/ modulator from a discrete-time /spl Delta//spl Sigma/ modulator is presented. With various simplifications, the resulting modulator has only a single path of integrators, making it robust to DC offsets. A time-interleaved by 2 continuous-time third-order low-pass /spl Delta//spl Sigma/ modulator is designed in a 0.18-/spl mu/m CMOS technology with an oversampling ratio of 5 at sampling frequencies of 100 and 200 MHz. Experimental results show that a signal-to-noise-plus-distortion ratio (SNDR) of 57 dB and a dynamic range of 60 dB are obtained with an input bandwidth of 10 MHz, and an SNDR of 49 dB with a dynamic range of 55 dB is attained with an input bandwidth of 20 MHz. The power consumption is 101 and 103 mW, respectively.     

A 1.5-V 12-bit power-efficient continuous-time third-order /spl Sigma//spl Delta/ modulator

This paper presents the design strategy, implementation, and experimental results of a power-efficient third-order low-pass /spl Sigma//spl Delta/ analog-to-digital converter (ADC) using a continuous-time (CT) loop filter. The loop filter has been implemented by using active RC integrators. Several power optimizations, design requirements, and performance limitations relating to circuit nonidealities in the CT modulator are presented. The influence of the low supply voltage on the various building blocks such as the amplifier as well as on the overall /spl Sigma//spl Delta/ modulator is discussed. The ADC was implemented in a 3.3-V 0.5-/spl mu/m CMOS technology with standard threshold voltages. Measurements of the low-power 1.5-V CT /spl Sigma//spl Delta/ ADC show a dynamic range and peak signal-to-noise-plus-distortion ratio of 80 and 70 dB, respectively, in a bandwidth of 25 kHz. The measured power consumption is only 135 /spl mu/W from a single 1.5-V power supply.     

IF-sampling fourth-order bandpass /spl Delta//spl Sigma/ modulator for digital receiver applications

Bandpass modulators sampling at high IFs (/spl sim/200 MHz) allow direct sampling of an IF signal, reducing analog hardware, and make it easier to realize completely software-programmable receivers. This paper presents the circuit design of and test results from a continuous-time tunable IF-sampling fourth-order bandpass /spl Delta//spl Sigma/ modulator implemented in InP HBT IC technology for use in a multimode digital receiver application. The bandpass /spl Delta//spl Sigma/ modulator is fabricated in AlInAs-GaInAs heterojunction bipolar technology with a peak unity current gain cutoff frequency (f/sub T/) of 130 GHz and a maximum frequency of oscillation (f/sub MAX/) of 130 GHz. The fourth-order bandpass /spl Delta//spl Sigma/ modulator consists of two bandpass resonators that can be tuned to optimize both wide-band and narrow-band operation. The IF is tunable from 140 to 210 MHz in this /spl Delta//spl Sigma/ modulator for use in multiple platform applications. Operating from /spl plusmn/5-V power supplies, the fabricated fourth-order /spl Delta//spl Sigma/ modulator sampling at 4 GSPS demonstrates stable behavior and achieves a signal-to-(noise + distortion) ratio (SNDR) of 78 dB at 1 MHz BW and 50 dB at 60 MHz BW. The average SNDR performance measured on over 250 parts is 72.5 dB at 1 MHz BW and 47.7 dB at 60 MHz BW.     

A novel noise efficient feedback DAC within a switched capacitor /spl Sigma//spl Delta/ ADC

Efficient sampling of the reference noise within a bilinear switched capacitor /spl Sigma//spl Delta/ analog-to-digital converter (ADC), resulting in improved thermal noise performance is presented. Bilinear integrators contain a zero at the Nyquist frequency, with the result that no charge is transferred from the reference when a transition occurs in the modulator output. The average noise power added by the reference digital-to-analog converter (DAC) can be reduced substantially if the reference DAC is sampled only when charge is to be transferred. For midscale inputs, the sampled noise from a single bit reference DAC is reduced by more than 5 dB. When multibit quantization and feedback is used the reference noise can be further suppressed, in the case of 5 bits of feedback the reference noise is reduced by more than 20 dB.     

Sturdy MASH /spl Delta//spl Sigma/ modulator

A new Delta-Sigma modulator is proposed. Its operation is similar to that of a multi-stage noise-shaping structure but requires no digital noise cancellation filters. Thus, the need for matching required between analogue and digital filters is eliminated. Simulation results and mathematical analysis demonstrate the effectiveness of this structure     

A high-frequency double-sampling second-order /spl Delta//spl Sigma/ modulator

As the minimum feature size of VLSI technologies scales down, more of the signal processing tasks are performed in the digital domain. This results in increased speed, resolution, and dynamic range requirements for the analog-to-digital converter (ADC). High-speed and high-accuracy designs can be achieved by using oversampling ADC structures, which demand amplifiers with a high gain and a high unity-gain frequency. Due to the difficulty to meet both of these specifications, the ADC resolution at a frequency in the megahertz range appears to be limited by amplifier settling requirements. Design techniques to improve the ADC performance are presented. The proposed modulator structure uses the double-sampled technique, which increases by a factor of two the maximum speed of operation and correctly operates even with low dc gain amplifiers. Furthermore, the signal-to-noise ratio is significantly improved by a calibration stage, which dynamically estimates the offset errors to be removed by a simple subtraction from the output signal.     

A continuous-time /spl Sigma//spl Delta/ Modulator with reduced sensitivity to clock jitter through SCR feedback

This paper presents a means to overcome the high sensitivity of continuous-time sigma-delta (/spl Sigma//spl Delta/) modulators to clock jitter by using a modified switched-capacitor structure with resistive element in the continuous-time feedback digital-analog converter (DAC). The reduced sensitivity to jitter is both simulated and proven by measured results from two implemented third-order modulators. Additionally, the nonideal behavior is analyzed analytically and by simulations.     

Self-tuning algorithms for high-performance bandpass switched-capacitor /spl Sigma//spl Delta/ modulators

Switched-capacitor high-frequency bandpass /spl Sigma//spl Delta/ modulators could suffer from capacitor mismatch, finite opamp dc gain, and finite opamp bandwidth. These problems make the notch frequency and the quality factor of the zeros of the noise transfer function to deviate from their nominal values, strongly affecting the modulator dynamic range (DR). In order to avoid this situation, two sampled-data algorithms have been developed which allow to self-calibrate the bandpass /spl Sigma//spl Delta/ modulators. They use 3500 gate and 0.043 mm/sup 2/ area and consume power only when they are active, while, when the system is on, they are off and do not interfere with standard operation. The validity of the proposal is demonstrated by a silicon prototype in which the proposed solution allows to guarantee a 75-dB DR performance also under worst case conditions. In the particular case, it allows for the recovery of 3 dB in the SNR for the 200-kHz FM band (from 73 to 76 dB).     

A continuous-time /spl Sigma//spl Delta/ ADC with increased immunity to interferers

Receivers are being digitized in a quest for flexibility. Analog filters and programmable gain stages are being exchanged for digital processing at the price of a very challenging ADC. This paper presents an alternative solution where the filter and programmable gain functionality is integrated into a /spl Sigma//spl Delta/ ADC. The novel filtering ADC is realized by adding a high-pass feedback path to a conventional /spl Sigma//spl Delta/ ADC while a compensating low-pass filter in the forward path maintains stability. As such, the ADC becomes highly immune to interferers even if they exceed the maximum allowable input level for the wanted channel. As a consequence, the ADC input range can be programmed dynamically to the level of the wanted signal only. This results in an input-referred dynamic range of 89 dB in 1-MHz bandwidth and an intentionally moderate output signal-to-noise-and-distortion ratio of 46-59 dB (depending on the programmed gain). The merged functionality enables a better overall power/performance balance for the receiver baseband. The design consumes less than 2 mW and active area is 0.14 mm/sup 2/ in a 0.18-/spl mu/m digital CMOS technology.     

Tunable continuous-time bandpass /spl Sigma//spl Delta/ modulators with fractional delays

An analytical design methodology for continuous-time (CT) bandpass (BP) /spl Sigma//spl Delta/ modulators is presented. Second- and fourth-order tunable continuous time BP /spl Sigma//spl Delta/ modulator design equations are presented. A novel /spl Sigma//spl Delta/ loop architecture, where the traditional CT BP loop filter function is replaced with the filter function with fractional delays, is proposed. Validity of the methodology is confirmed by mixed-signal behavioral simulations.     

Double-sampling single-loop /spl Sigma//spl Delta/ modulator topologies for broad-band applications

This paper presents novel double sampling high-order single loop sigma-delta modulator structures for wide-band applications. To alleviate the quantization noise folding into the inband frequency region, two previously reported techniques are used. The digital-to-analog converter's sampling paths are implemented with the single-capacitor approach and an additional zero is placed at the half of the sampling frequency of the modulator's noise transfer function (NTF). The detrimental effect of this additional zero on both the NTF and signal transfer function is also resolved through the proposed modulator architectures with a low additional circuit requirement.     

Improved design method for continuous-time quadrature bandpass /spl Sigma//spl Delta/ ADCs

In continuous-time quadrature bandpass /spl Sigma//spl Delta/ ADCs it is desirable to limit the number of cross-couplings. This can be achieved by implementing the loop as a cascade of complex integrators with only real coefficients. It is shown that this may result in a very poor approximation of the desired noise transfer function, because the effect of the DAC pulse is not taken into account correctly. A simple implementation that solves this problem is proposed.     

High-level synthesis of switched-capacitor, switched-current and continuous-time /spl Sigma//spl Delta/ modulators using SIMULINK-based time-domain behavioral models

This paper presents a high-level synthesis tool for /spl Sigma//spl Delta/ modulators (/spl Sigma//spl Delta/Ms) that combines an accurate SIMULINK-based time-domain behavioral simulator with a statistical optimization core. Three different circuit techniques for the modulator implementation are considered: switched-capacitor, switched-current and continuous-time. The behavioral models of these circuits, that take into account the most critical limiting factors, have been incorporated into the SIMULINK environment by using S-function blocks, which drastically increase the computational efficiency. The precision of these models has been validated by electrical simulations using HSPICE and experimental measurements from several silicon prototypes. The combination of high accuracy, short CPU time and interoperability of different circuit models together with the efficiency of the optimization engine makes the proposed tool an advantageous alternative for /spl Sigma//spl Delta/M synthesis. The implementation on the well-known MATLAB/SIMULINK platform brings numerous advantages in terms of data manipulation, processing capabilities, flexibility and simulation with other electronic subsystems. Moreover, this is the first tool dealing with the synthesis of /spl Sigma//spl Delta/Ms using both discrete-time and continuous-time circuit techniques.     

A 14-bit high-temperature /spl Sigma//spl Delta/ modulator in standard CMOS

Experimental verification is given for the use of /spl Sigma//spl Delta/ modulation for high-temperature applications (/spl ges/approximately 150/spl deg/C) in a standard CMOS process. Switched-capacitor circuits are used to implement a second-order single-stage and a third-order 2-1 MASH /spl Sigma//spl Delta/ modulator with single-bit quantization. The two modulators have an oversampling ratio of 256 with an input signal bandwidth of 500 Hz. The modulators were fabricated in a 1.5-/spl mu/m standard CMOS technology. A fully differential signal path and near minimum sized switches are used to mitigate the effect of large junction-to-substrate leakage current present at high temperatures. Experimental results show both modulators are capable of over 14 bits of resolution at 225/spl deg/C and over 13 bits of resolution at 255/spl deg/C. Results show that the single-stage modulator is more resistant to high-temperature circuit impairment than is the MASH cascaded structure.     

Cascade /spl Sigma//spl Delta/ modulator with digital correction for finite amplifier gain effects

A simple and fully digital solution to correct the effect of amplifier finite gain in cascade /spl Sigma//spl Delta/ modulators is presented. The main contribution of this study is a simple digital method to evaluate the integrator pole errors, which are further taken into account to modify the reconstruction filter. The method is applied to a 2-1 cascade modulator.     

Resonator-based multi-stage /spl Sigma//spl Delta/ modulator for wideband applications with improved dynamic range

A new design methodology for wideband, multi-stage, multi-bit /spl Sigma//spl Delta/ modulators (/spl Sigma//spl Delta/Ms) with improved dynamic range, is presented. The key to improving dynamic range is to have the first stage oscillated, then the coarse quantisation noise vanishes and hence circuit non-linearities do not cause a leakage quantisation noise problem. Based on the proposed methodology, a fourth-order four-bit /spl Sigma//spl Delta/M can achieve the dynamic range of 80 dB at the OSR of 8 without using additional calibration techniques.     

Highly linear 2.5-V CMOS /spl Sigma//spl Delta/ modulator for ADSL+

We present a 90-dB spurious-free dynamic range sigma-delta modulator (/spl Sigma//spl Delta/M) for asymmetric digital subscriber line applications (both ADSL and ADSL+), with up to a 4.4-MS/s digital output rate. It uses a cascade (MASH) multibit architecture and has been implemented in a 2.5-V supply, 0.25-/spl mu/m CMOS process with metal-insulator-metal capacitors. The prototypes feature 78-dB dynamic range (DR) in the 30-kHz to 2.2-MHz band (ADSL+) and 85-dB DR in the 30-kHz to 1.1-MHz band (ADSL). Integral and differential nonlinearity are within /spl plusmn/0.85 and /spl plusmn/0.80 LSB/sub 14 b/, respectively. The /spl Sigma//spl Delta/ modulator and its auxiliary blocks (clock phase and reference voltage generators, and I/O buffers) dissipate 65.8 mW. Only 55 mW are dissipated in the /spl Sigma//spl Delta/ modulator.     

Noise-coupled /spl Delta//spl Sigma/ ADC's

The first-order noise coupling scheme proposed earlier is generalised to the realisation of higher-order enhancement. It is also extended to single-stage DeltaSigma loops, and to split structures with self-enhancement. The advantages and limitations of these new DeltaSigma architectures are compared with those of conventional single-stage and cascade DeltaSigma structures. As demonstrated by an example, they exhibit improved stability and robustness under practical fabrication conditions     

Interstage network to control overload in cascaded continuous-time /spl Sigma//spl Delta/ modulators

An improved interstage network suitable for avoiding overload and for increasing the signal-to-noise ratio in low-oversampling-ratio cascaded continuous-time SigmaDelta modulators is reported. Feedforward coefficients, going from the input signal to the second stage, are used to control overload without affecting the behaviour of the noise cancellation filters. Moreover, the anti-aliasing functionality is preserved. Simulation results show the utility of the proposed network in terms of the overload performance