Synthesis, microstructure, and photocatalysis of In2O3 hollow particles

Indium oxide (In₂O₃) microspheres with hollow interiors have been prepared by a facile implantation route which enables indium ions released from indium-chloride precursors to implant into nonporous polymeric templates in C₂Cl₄ solvent. The templates are then removed upon calcination at 500 °C in air atmosphere, forming hollow In₂O₃ particles. Specific surface area (0.5-260 m² g⁻¹) and differential pore volume (7 × 10⁻⁹ to 3.8 × 10⁻⁴ m³ g⁻¹ Å⁻¹) of the hollow particles can be tailored by adjusting the precursor concentration. For the hollow In₂O₃ particles with high surface area (260 m² g⁻¹), an enhanced photocatalytic efficiency (up to ∼one-fold increase) against methylene blue (MB) dye is obtained under UV exposure for the aqueous In₂O₃ colloids with a dilute solids concentration of 0.02 wt.%.     

Characterization of photovoltaics with In2S3 nanoflakes/p-Si heterojunction

We demonstrate that heterojunction photovoltaics based on hydrothermal-grown In₂S₃ on p-Si were fabricated and characterized in the paper. An n-type In₂S₃ nanoflake-based film with unique ''cross-linked network’ structure was grown on the prepared p-type silicon substrate. It was found that the bandgap energy of such In₂S₃ film is 2.5 eV by optical absorption spectra. This unique nanostructure significantly enhances the surface area of the In₂S₃ films, leading to obtain lower reflectance spectra as the thickness of In₂S₃ film was increased. Additionally, such a nanostructure resulted in a closer spacing between the cross-linked In₂S₃ nanostructures and formed more direct conduction paths for electron transportation. Thus, the short-circuit current density (Jsc) was effectively improved by using a suitable thickness of In₂S₃. The power conversion efficiency (PCE, η) of the AZO/In₂S₃/textured p-Si heterojunction solar cell with 100-nm-thick In₂S₃ film was 2.39%.     

Preparation and electrochemical performance of In-doped ZnO as anode material for Ni–Zn secondary cells

In-doped ZnO (IZO) samples were synthesized by a simple co-precipitation method. X-ray diffraction (XRD) patterns, Raman spectra and scanning electron microscopy (SEM) images show that IZO with 2.5 wt% In₂O₃ has a pure wurtzite structure and a plate-like morphology. IZO with 16.3 wt% In₂O₃ (theoretical value) mainly shows a wurtzite structure. Cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and galvanostatic charge–discharge measurement were utilized to examine the electrochemical performances of IZO with 2.5 wt% In₂O₃ as anode material for Ni–Zn simulated cells. Compared with the physical mixture of ZnO with In₂O₃, IZO increases the charge-transfer resistance of zinc electrode. Furthermore, the initial discharge capacity of IZO is 569 mAh g⁻¹, and the discharge capacity decays slightly with the capacity retention ratio of 95.2% over 73 cycles, which is much higher than that of the physical mixture of ZnO with In₂O₃.     

Photoinduced Heterogeneous Processes on Chemical Phase Components of Solid Tropospheric Aerosols

This work shows the results of photoinduced process investigations over some metal oxides of the semiconductor type (In₂O₃, Sc₂O₃, V₂O₅ and MoO₃) and insulator type (MgO). These metal oxides can be the chemical phase components of solid tropospheric aerosols. The quantum yields and spectral dependencies of the quantum yields of photoadsorption and photocatalytic oxidation in the spectral region including the spectral region of solar tropospheric irradiation are determined.     

Preparation, characterization and electrocatalytic properties of poly(luminol) and polyoxometalate hybrid film modified electrodes

Hybrid films composed of poly(luminol) and nanometer-sized clusters of polyoxometalate, SiMo₁₂O₄₀⁴⁻ and PMo₁₂O₄₀³⁻ have been prepared in acidic aqueous solutions. These films are stable and electrochemically active, and produced on glassy carbon, platinum, gold and transparent semiconductor tin oxide electrodes. The electrochemical quartz crystal microbalance and cyclic voltammetry were used to study in situ growth of the hybrid poly(luminol)/SiMo₁₂O₄₀⁴⁻ and poly(luminol)/PMo₁₂O₄₀³⁻. Both the poly(luminol)/SiMo₁₂O₄₀⁴⁻ and poly(luminol)/PMo₁₂O₄₀³⁻ hybrid films showed four redox couples and the electrochemical properties were compared to SiMo₁₂O₄₀⁴⁻ and PMo₁₂O₄₀³⁻. When transferred to various acidity aqueous solutions, the four redox couples and the formal potentials of two hybride film were observed to be pH-dependent. The electrocatalytic reduction of ClO₃⁻, BrO₃⁻, IO₃⁻, S₂O₈²⁻ and NO₂⁻ by a poly(luminol)/PMo₁₂O₄₀³⁻ hybrid film in an acidic aqueous solution showed an electrocatalytic reduction activity of IO₃⁻ > BrO₃⁻ and ClO₃⁻. The electrocatalytic oxidation of dopamine and epinephrine by a poly(luminol)/PMo₁₂O₄₀³⁻ hybrid film was also investigated.     

A Flower-like In2O3 Catalyst Derived via Metal–Organic Frameworks for Photocatalytic Applications

The most pressing concerns in environmental remediation are the design and development of catalysts with benign, low-cost, and efficient photocatalytic activity. The present study effectively generated a flower-like indium oxide (In₂O₃-MF) catalyst employing a convenient MOF-based solvothermal self-assembly technique. The In₂O₃-MF photocatalyst exhibits a flower-like structure, according to morphology and structural analysis. The enhanced photocatalytic activity of the In₂O₃-MF catalyst for 4-nitrophenol (4-NP) and methylene blue (MB) is likely due to its unique 3D structure, which includes a large surface area (486.95 m² g⁻¹), a wide spectrum response, and the prevention of electron–hole recombination compared to In₂O₃-MR (indium oxide-micro rod) and In₂O₃-MD (indium oxide-micro disc). In the presence of NaBH₄ and visible light, the catalytic performances of the In₂O₃-MF, In₂O₃-MR, and In₂O₃-MD catalysts for the reduction of 4-NP and MB degradation were investigated. Using In₂O₃-MF as a catalyst, we were able to achieve a 99.32 percent reduction of 4-NP in 20 min and 99.2 percent degradation of MB in 3 min. Interestingly, the conversion rates of catalytic 4-NP and MB were still larger than 95 and 96 percent after five consecutive cycles of catalytic tests, suggesting that the In₂O₃-MF catalyst has outstanding catalytic performance and a high reutilization rate.     

Preparation of In,H-ZSM-5 for DeNOx reactions by solid-state ion exchange

A simple method is proposed to prepare In,H-ZSM-5 catalyst for DeNOx reactions. This consists of mechanically mixing the fine powders of In₂O₃ and H-ZSM-5 followed by heating in oxygen free inert gas flow to 580 °C where indium undergoes thermal auto-reduction and moves into exchange positions as In⁺ without destroying the crystalline structure of the zeolite.It was evidenced by IR, temperature-programmed reduction (TPR) and reoxidation that, once In⁺ was introduced into the lattice either by reductive solid-state ion exchange (RSSIE) or by thermal auto-reductive SSIE, it can be oxidized by O₂ or in the DeNOx reaction to (InO)⁺. The formed (InO)⁺ can easily be reduced to In⁺ suggesting that In,H-ZSM-5 might be a good catalyst for reactions where a redox cycle in the catalyst is involved in the reaction mechanism.Selective catalytic reduction (SCR) by methane proved that only a small fraction of In exchanged, together with some acid sites of the zeolite formed the active center for the catalytic reaction. XRD, XPS and FT-IR using pyridine proved that the structure of the zeolite and these centers are stable under reaction conditions and In is mainly in the form of (InO)⁺ in the used catalyst.     

Side-by-Side In(OH)<Subscript>3</Subscript> and In<Subscript>2</Subscript>O<Subscript>3</Subscript> Nanotubes: Synthesis and Optical Properties

A simple and mild wet-chemical approach was developed for the synthesis of one-dimensional (1D) In(OH)₃ nanostructures. By calcining the 1D In(OH)₃ nanocrystals in air at 250 °C, 1D In₂O₃ nanocrystals with the same morphology were obtained. TEM results show that both 1D In(OH)₃ and 1D In₂O₃ are composed of uniform nanotube bundles. SAED and XRD patterns indicate that 1D In(OH)₃ and 1D In₂O₃ nanostructures are single crystalline and possess the same bcc crystalline structure as the bulk In(OH)₃ and In₂O₃, respectively. TGA/DTA analyses of the precursor In(OH)₃ and the final product In₂O₃ confirm the existence of CTAB molecules, and its content is about 6%. The optical absorption band edge of 1D In₂O₃ exhibits an evident blueshift with respect to that of the commercial In₂O₃ powders, which is caused by the increasing energy gap resulted from decreasing the grain size. A relatively strong and broad purple-blue emission band centered at 440 nm was observed in the room temperature PL spectrum of 1D In₂O₃ nanotube bundles, which was mainly attributed to the existence of the oxygen vacancies.     

Growth of In2O3 Nanowires Catalyzed by Cu via a Solid–Liquid–Solid Mechanism

In₂O₃ nanowires that are 10–50 nm in diameter and several hundred nanometers to micrometers in length have been synthesized by simply annealing Cu–In compound at a relatively low temperature of 550°C. The catalysis of Cu on the growth of In₂O₃ nanowires is investigated. It is believed that the growth of In₂O₃ nanowires is via a solid–liquid–solid (SLS) mechanism. Moreover, photoluminescence (PL) peaks of In₂O₃ nanowires at 412 and 523 nm were observed at room temperature, and their mechanism is also discussed.     

Dehydrogenation of propane in the presence of N2O over In2O3―Al2O3 mixed oxide catalysts

Dehydrogenation of propane coupled with N₂O over a series of binary In₂O₃―Al₂O₃ mixed oxides was investigated. In contrast to the poor performance for sole N₂O decomposition, a remarkable synergy was identified between N₂O decomposition and propane dehydrogenation. Among the catalysts tested, the In₂O₃―Al₂O₃ sample containing a 20 mol% In₂O₃ showed the highest activity for propane dehydrogenation in the presence of N₂O. Moreover, stability far superior to those of the conventional iron-based materials was observed, attributable to the moderate surface acidity of the In―Al―O composite. The essential role of N₂O is suggested to generate active oxygen species facilitating propane dehydrogenation.     

The effect of Bi2O3 compensation during thermal treatment on the crystalline and electrical characteristics of bismuth titanate thin films

Bismuth titanate thin films are deposited on ITO/glass substrates by rf magnetron sputtering at room temperature using a Bi₄Ti₃O₁₂ ceramic target. The deposited Bi₄Ti₃O₁₂ films are annealed in a conventional furnace in ambient air for 10 min at temperatures ranging from 550 to 640 °C. One specimen is annealed in a crucible containing additional Bi₂O₃ compensation powder, while the other specimen is annealed in ambient air. XRD analysis shows that the crystal phases of films annealed with Bi₂O₃ powder are better than those of films annealed without Bi₂O₃ powder. Furthermore, the EDS results reveal that the bismuth weight percentage of the former is higher than that of the latter. SIMS analysis shows that the bismuth decreases near the surface of Bi₄Ti₃O₁₂ film annealed without Bi₂O₃ powder, but reveals a stable distribution throughout the film annealed with Bi₂O₃ powder. These results imply that bismuth is readily evaporated during the thermal treatment process, particularly from the region near the film surface. Finally, the dielectric and polarization properties of the thin films annealed with Bi₂O₃ powder are found to be superior to those of the films annealed in ambient air.     

Promotional effect of H2O on the activity of In2O3‐doped Ga2O3–Al2O3 for the selective reduction of nitrogen monoxide

Effect of metal oxide additives on the catalytic performance of Ga₂O₃–Al₂O₃ prepared by the sol–gel method for the selective reduction of NO with propene in the presence of oxygen was studied. Of several metal oxide additives, the addition of In₂O₃ enhanced drastically the activity of Ga₂O₃–Al₂O₃ for NO reduction by propene in the presence of H₂O. In addition, the activity of In₂O₃‐doped Ga₂O₃–Al₂O₃ catalyst was extremely intensified by the presence of H₂O below 350°C. The promotional effect of H₂O was interpreted by the suppression of undesirable propene oxidation and the removal of carbonaceous materials deposited on the catalyst surface. We also found that close interaction of In₂O₃ and Ga₂O₃ is necessary for the enhancement of activity by H₂O. A lot of hydrocarbons except methane and oxygenated compounds served as good reducing agents, among which propene and 2‐propanol were the most efficient ones. In₂O₃‐doped Ga₂O₃–Al₂O₃ catalyst was capable of reducing NO into N₂ quite efficiently in the presence of H₂O at a very high space velocity. This revised version was published online in July 2006 with corrections to the Cover Date.     

Mechanistic study of the reduction of oxygen in air electrode with manganese oxides as electrocatalysts

Electrochemical reduction of oxygen (O₂) in air electrode with manganese oxides (MnOx) as electrocatalysts was studied with MnOx/Nafion-modified gold (Au) electrodes using cyclic voltammetry, potential-controlled amperometry and rotating ring-disk electrode (RRDE) voltammetry in alkaline aqueous solution. At Nafion-modified (MnOx free) Au electrode, O₂ reduction undergoes two successive two-electron processes with HO₂⁻ as intermediate. The presence of MnOx, including Mn₂O₃, Mn₃O₄, Mn₅O₈ and MnOOH, on Nafion-modified Au electrodes obviously increases the first reduction peak current of O₂ to hydrogen peroxide (HO₂⁻ in this case) and decreases the second one of HO₂⁻ to OH⁻, while does not shift the reduction potential. MnOx was found to show catalytic activity for the disproportionation reaction of HO₂⁻ to O₂ and OH⁻ and thus, the O₂ reduction in air electrode was considered to include an initial two-electron reduction of O₂ to HO₂⁻ followed by a disproportionation reaction of HO₂⁻ into O₂ and OH⁻ catalyzed by MnOx. The excellent activity of MnOx for the follow-up disproportionation reaction substantially results in an overall four-electron reduction of O₂ at MnOx/Nafion-modified Au electrodes in the first reduction step, depending on potential scan rate and the kind of MnOx. The present work provides a scientific significance of the mechanism of O₂ reduction in air electrode using MnOx as electrocatalysts to effect a four-electron reduction of O₂ to OH⁻.     

A comparative electrochemical study of LiMn2O4 spinel thin-film and porous laminate

Novel Electrostatic Spray Deposition (ESD) technique was used to fabricate LiMn₂O₄ spinel thin-films. Cyclic voltammograms of both the ESD and porous laminate films show the double peaks in the 4.0 V range characteristic of the LiMn₂O₄ spinel materials. The porous laminates exhibit two semicircles in the impedance spectra while the ESD films show only one single semicircle. The diffusion time constant in the laminate films was typically one order of magnitude larger than that in the ESD thin-films. The apparent lithium-ion chemical diffusion coefficient in LiMn₂O₄ was found to be of the order of 10⁻⁹ cm²/s for both the porous laminate film and the ESD films despite the difference in the diffusion time constants.     

Investigation on Photovoltaic Performance based on Matchstick-Like Cu2S–In2S3 Heterostructure Nanocrystals and Polymer

In this paper, we synthesized a novel type II cuprous sulfide (Cu₂S)–indium sulfide (In₂S₃) heterostructure nanocrystals with matchstick-like morphology in pure dodecanethiol. The photovoltaic properties of the heterostructure nanocrystals were investigated based on the blends of the nanocrystals and poly(2-methoxy-5-(2′-ethylhexoxy)-p-phenylenevinylene) (MEH-PPV). In comparison with the photovoltaic properties of the blends of Cu₂S or In₂S₃ nanocrystals alone and MEH-PPV, the power conversion efficiency of the hybrid device based on blend of Cu₂S–In₂S₃ and MEH-PPV is enhanced by ~3–5 times. This improvement is consistent with the improved exciton dissociation or separation and better charge transport abilities in type II heterostructure nanocrystals.     

Memory characteristics of multi-stacked thin films using La2O3 and LaAlO3 as charge trap layer

Al₂O₃/La₂O₃/Al₂O₃ (ALA) and Al₂O₃/LaAlO₃/Al₂O₃ (A/LAO/A) multi-stacked films were deposited on Si substrates by MOCVD. No interfacial layers (Al_xSi_yO_z) were observed in TEM images, and the thickness ratio of the tunnel oxide (bottom oxide), trap layer (middle oxide), and blocking oxide (top oxide) was about (1:1.3:3) in both films. Memory windows of the (ALA) and (A/LAO/A) films were 1.31 V and 3.13 V, respectively. Each value in the program/erase cycle test was maintained for up to 10⁴ cycles.     

Nanocrystalline In2O3-SnO2 thick films for low-temperature hydrogen sulfide detection

Nanocrystalline In₂O₃-SnO₂ thick films were fabricated using the screen-printing technique and their responses toward low concentrations of H₂S in air (2-150 ppm) were tested at 28-150 °C. The amount of In₂O₃-loading was varied from 0 to 9 wt.% of SnO₂ and superb sensing performance was observed for the sensor loaded with 7 wt.% In₂O₃, which might be attributed to the decreased crystallite size as well as porous microstructure caused by the addition of In₂O₃ to SnO₂ without structural modification. The interfacial barriers between In₂O₃ and SnO₂ might be another major factor. Typically, the response of 7 wt.% In₂O₃-loaded SnO₂ sensor toward 100 ppm of H₂S was 1481 at room temperature and 1921 at optimal operating temperature (40 °C) respectively, and showed fast and recoverable response with good reproducibility when operated at 70 °C, which are highly attractive for the practical application in low-temperature H₂S detection.     

High Efficiency of Noble Metal and Metal Oxide Catalyst Systems for the Selective Reduction of NO with Propene in Lean Exhaust Gas

An investigation was conducted of noble metal and metal oxide catalysts deposited on Al₂O₃. The noble metals Pt, Pd, Rh the metal oxides CuO, SnO₂, CoO, Ag₂O, In₂O₃, catalysts were examined. Also investigated were noble metal Pt, Pd, Rh-doped In₂O₃/Al₂O₃ catalysts prepared by single sol–gel method. Both were studied for their capability to reduce NO by propene under lean conditions. In order to improve the catalytic activity and the temperature window, the intermediate addition propene between a Pt/Al₂O₃ oxidation and metal oxide combined catalyst system was also studied. Pt/Al₂O₃ and In₂O₃/Al₂O₃ combined catalyst showed high NO reduction activity in a wider temperature window, and more than 60% NO conversion was observed in the temperature range of 300–550 °C.     

Femtosecond Carrier Dynamics in In2O3 Nanocrystals

We have studied carrier dynamics in In₂O₃ nanocrystals grown on a quartz substrate using chemical vapor deposition. Transient differential absorption measurements have been employed to investigate the relaxation dynamics of photo-generated carriers in In₂O₃ nanocrystals. Intensity measurements reveal that Auger recombination plays a crucial role in the carrier dynamics for the carrier densities investigated in this study. A simple differential equation model has been utilized to simulate the photo-generated carrier dynamics in the nanocrystals and to fit the fluence-dependent differential absorption measurements. The average value of the Auger coefficient obtained from fitting to the measurements was γ = 5.9 ± 0.4 × 10⁻³¹ cm⁶ s⁻¹. Similarly the average relaxation rate of the carriers was determined to be approximately τ = 110 ± 10 ps. Time-resolved measurements also revealed ~25 ps delay for the carriers to reach deep traps states which have a subsequent relaxation time of approximately 300 ps.     

Electrochemical investigation of the dimeric oxo-bridged ruthenium complex in aqueous solution and its incorporation within a cation-exchange polymeric film on the electrode surface for electrocatalytic activity of hydrogen peroxide oxidation

Electrochemical behavior of oxo-bridged dinuclear ruthenium(III) complex ([(bpy)2(H₂O)Ru^III-O-Ru^III(H₂O)(bpy)2]⁴⁺) has been studied in aqueous solution (KCl 0.5 mol L⁻¹) by both cyclic and rotating disk electrode (RDE) voltammetry in order to identify and elucidate the reaction mechanism. Modified electrode containing the oxo-bridged ruthenium complex incorporated into a cation-exchange polymeric film deposited onto platinum electrode surface was studied. Cyclic voltammetry at the modified electrode in KCl solution showed a single-electron reduction/oxidation of the couple Ru^III-O-Ru^III/Ru^III-O-Ru^IV. The modified electrode exhibited electrocatalytic property toward hydrogen peroxide oxidation in KCl solution with a decrease of the overpotential of 340 mV compared with the platinum electrode. The Tafel plot analyses have been used to elucidate the kinetics and mechanism of the hydrogen peroxide oxidation. The first at low overpotential region there is no significant change in the Tafel slope (∼0.130 V dec⁻¹) with varying peroxide concentration. The second region at higher overpotential the slope values (0.91–0.47 V dec⁻¹) were depended on the peroxide concentration. The apparent reaction order for H₂O₂ varies from 0.16 to 0.50 in function of the applied potential. The apparent reaction order (at constant potential) with respect to H⁺ concentration of 10⁻⁵ to 10⁻¹ mol L⁻¹ was 0.25. A plot of the anodic current vs. the H₂O₂ concentration for chronoamperometry (potential fixed = +0.61 V) at the modified electrode was linear in the 1.0 × 10⁻⁵ to 2.5 × 10⁻⁴ mol L⁻¹ concentration range.