Textural and pseudocapacitive characteristics of sol-gel derived RuO2·xH2O: Hydrothermal annealing vs. annealing in air

Hydrous ruthenium dioxide (RuO₂·xH₂O) prepared in a modified sol-gel process was subjected to annealing in air and water at various temperatures for supercapacitor applications. The textural and pseudocapacitive characteristics of RuO₂·xH₂O annealed in air and water were systematically compared to show the benefits of annealing in water (denoted as hydrothermal annealing). An important concept that hydrothermal annealing effectively restricts condensation of hydroxyl groups within nanoparticles, inhibits crystal growth, and maintains high water content of RuO₂·xH₂O is demonstrated in this work. The unique textural characteristics of hydrothermally annealed RuO₂·xH₂O are attributable to the high-pressured, water-enriched surroundings which restrain coalescence of RuO₂·xH₂O nanocrystallites. The crystalline, hydrous nature of hydrothermally annealed RuO₂·xH₂O favors the utilization of active species in addition to a merit of minor dependence of specific capacitance on the scan rate of CV for pseudocapacitors. As a result, RuO₂·xH₂O with hydrothermal annealing at 225 °C for 24 h exhibits 16 wt.% water, an average particle size of about 7 nm, and specific capacitance of ca. 390 F g⁻¹.     

Hydrothermal synthesis and electrochemical capacitance of RuO2·xH2O loaded on benzenesulfonic functionalized MWCNTs

Amorphous RuO₂·xH₂O was well coated on the benzenesulfonic functionalized multi-wall carbon nanotubes (f-MWCNTs) successfully via hydrothermal method. The decorated benzenesulfonic groups served as a bifunctional role both for solubilizing and dispersing MWCNTs into aqueous solution and for tethering Ru³⁺ precursor to facilitate the following uniform chemical deposition of RuO₂·xH₂O. The electrochemical performance of RuO₂/f-MWCNTs and utilization of RuO₂·xH₂O were evidenced by cyclic voltammetry and galvanostatic charge/discharge tests. The specific capacitance of 1143 Fg⁻¹ for RuO₂·xH₂O was obtained from RuO₂/f-MWCNTs with 32 wt.% RuO₂·xH₂O, which was much higher than that of just 798 Fg⁻¹ for the RuO₂/p-MWCNTs. Even though the RuO₂·xH₂O loading increases to 45 wt.%, the utilization of RuO₂·xH₂O still possesses as high as 844.4 Fg⁻¹, indicating a good energy capacity in the case of high loading.     

RuO2·xH2O/NiO composites as electrodes for electrochemical capacitors: Effect of the RuO2 content and the thermal treatment on the specific capacitance

RuO₂·xH₂O/NiO composites having RuO₂ contents in the range 0-100 wt.% have been prepared by a co-precipitation method. Structural, microstructural and textural transformations after heating the as-prepared composites at 200 and 600 °C have been followed by X-ray diffraction, scanning electron microscopy (SEM) and nitrogen adsorption/desorption isotherms. At 200 °C the composites are made of micrometric particles in which nanometric crystallites of the two oxides are aggregated. The composites show microporosity (0.02-0.10 cm³/g), mesoporosity (0.07-0.12 cm³/g) and relatively high specific surface area (62-309 m²/g). At 600 °C the composites are fully dehydrated and RuO₂ has crystallized and segregated. Microporosity and mesoporosity as well as specific surface area are strongly decreased. Specific capacitance and specific surface area of the composites heated at 200 and 600 °C have been measured and discussed on the basis of the RuO₂ content. For comparison the specific capacitance and specific surface area of mixtures of NiO and RuO₂·xH₂O (or RuO₂) have been taken as references. The higher specific capacitance of the 200 °C-heated composites compared to the 600 °C-heated ones is due to the higher specific surface area of the former and the higher pseudocapacitance of RuO₂·xH₂O compared to RuO₂. The discussion reported in this work can be applied to other composites such as RuO₂·xH₂O/carbon and RuO₂·xH₂O/other oxides.     

Two-step hydrothermal synthesis of Ru-Sn oxide composites for electrochemical supercapacitors

A two-step hydrothermal process was developed to synthesize hydrous 30RuO₂-70SnO₂ composites with much better capacitive performances than those fabricated through the normal hydrothermal process, co-annealing method, or modified sol-gel procedure. A very high specific capacitance of RuO₂ (C_S,Ru), ca. 1150 F g⁻¹, was obtained when this composite was synthesized via this two-step hydrothermal process with annealing in air at 150 °C for 2 h. The voltammetric currents of this annealed composite were found to be quasi-linearly proportional to the scan rate of CV (up to 500 mV s⁻¹), demonstrating its excellent power property. From Raman, UV-vis spectroscopic and TEM analyses, the reduction in mean particulate size is clearly found for this two-step oxide composite, attributable to the co-precipitation of (Ru_δSn_1−δ)O₂·xH₂O onto partially dissolved SnO₂·xH₂O and the formation of (Ru_δSn_1−δ)O₂·xH₂O crystallites in the second step. This effect significantly promotes the utilization of RuO₂ (i.e., very high C_S,Ru). The excellent capacitive performances, very similar to that of RuO₂·xH₂O, suggest the deposition of RuO₂-enriched (Ru_δSn_1−δ)O₂·xH₂O onto SnO₂·xH₂O seeds as well as the individual formation of (Ru_δSn_1−δ)O₂·xH₂O crystallites in the second hydrothermal step.     

Soft template synthesis of mesoporous Co3O4/RuO2·xH2O composites for electrochemical capacitors

Co₃O₄/RuO₂·xH₂O composites with various Ru content (molar content of Ru = 5%, 10%, 20%, 50%) were synthesized by one-step co-precipitation method. The precursors were prepared via adjusting pH of the mixed aqueous solutions of Co(NO₃)₂·6H₂O and RuCl₃·0.5H₂O by using Pluronic123 as a soft template. For the composite with molar ratio of Co:Ru = 1:1 annealed at 200 °C, Brunauer-Emmet-Teller (BET) results indicated that the composite showed mesoporous structure, and the specific surface area of the composite was as high as 107 m² g⁻¹. The electrochemical performances of these composites were measured in 1 M KOH electrolyte. Compared with the composite prepared without template, the composite with P123 exhibited a higher specific capacitance. When the molar content of Ru was rising, the specific capacitance of the composites increased significantly. It was also observed that the crystalline structures as well as the electrochemical activities were strongly dependent on the annealing temperature. A capacitance of 642 F/g was obtained for the composite (Co:Ru = 1:1) annealed at 150 °C. Meanwhile, the composites also exhibited good cycle stability. Besides, the morphologies and textural characteristic of the samples were also investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM).     

Synthesis and characterization of ZnxMg1 − xGa2O4:Co fabricated by low-temperature burning method

A series of Zn_xMg_1 − xGa₂O₄:Co²⁺ spinels (x = 0, 0.25, 0.5, 0.75, and 1.0) was successfully produced through low-temperature burning method by using Mg(NO₃)₂·4H₂O, Zn(NO₃)₂·6H₂O, Ga(NO₃)₃·6H₂O, CO(NH₂)₂, NH₄NO₃, and Co(NO₃)₂·6H₂O as raw materials. The product was characterized by X-ray diffraction, transmission electron microscopy, and photoluminescence spectroscopy. The product was not merely a simple mixture of MgGa₂O₄ and ZnGa₂O₄; rather, it formed a solid solution. The lattice constant of Zn_xMg_1 − xGa₂O₄:Co²⁺ (0 ≤ x ≤ 1.0) crystals has a good linear relationship with the doping density, x. The synthesized products have high crystallinities with neat arrays. Based on an analysis of the form and position of the emission spectrum, the strong emission peak around the visible region (670 nm) can be attributed to the energy level transition [⁴T₁(⁴P) → ⁴A₂(⁴F)] of Co²⁺ in the tetrahedron. The weak emission peak in the near-infrared region can be attributed to the energy level transition [⁴T₁(⁴P) → ⁴T₂(⁴F)] of Co²⁺ in the tetrahedron.     

Electrochemical capacitance of nanoporous hydrous RuO2 templated by anionic surfactant

The nanoporous RuO₂·3.38H₂O was synthesized with a surfactant template using sodium dodecyl sulfate. The surface area of the material amounted to 220 m² g⁻¹ while the maximum specific capacitance obtained was 870 Fg⁻¹ at a scan rate of 10 mV s⁻¹. The specific capacitance of nanoporous RuO₂·3.38H₂O electrode exhibits enhancement, compared with other porous RuO₂ materials synthesized by different methods. The nanoporous RuO₂·3.38H₂O is a very promising material for high performance capacitance.     

Anodic deposition of hydrous ruthenium oxide for supercapaciors: Effects of the AcO concentration, plating temperature, and oxide loading

Effects of the sodium acetate (NaCH₃COO, denoted as NaAcO) concentration, plating temperature, and oxide loading on the pseudocapacitive characteristics of hydrous ruthenium oxide (denoted as RuO₂·xH₂O) films anodically plated from aqueous RuCl₃·xH₂O media were systematically investigated in this work. The electrochemical behavior of RuO₂·xH₂O with annealing in air at 200 °C for 2 h is approximately independent of the NaAcO concentration and plating temperature although a negative shift in the onset and peak potentials of deposition with rising the plating temperature is found. The morphologies and adhesion of RuO₂·xH₂O deposits strongly depend on the deposition rate which is obviously influenced by varying the above two deposition variables. The specific capacitance of RuO₂·xH₂O is monotonously decreased from 760 to 505 F g⁻¹ when the oxide loading is gradually increased from 0.34 to 1.0 mg cm⁻², due to the longer pathways of both electrons and protons during the redox transitions. The XRD and Raman spectroscopic analyses reveal the extremely localized crystalline nature of as-deposited RuO₂·xH₂O. All RuO₂·xH₂O deposits show the ideal pseudocapacitive characteristics, definitely illustrating the merits of RuO₂·xH₂O prepared by anodic deposition without considering the advantages of its simplicity, one-step, reliability, low cost, and versatility for electrode preparation.     

Synthesis and electrochemical characterization of mesoporous CoxNi1−x layered double hydroxides as electrode materials for supercapacitors

A novel nanostructured mesoporous Co_xNi_1−x layered double hydroxides (Co_xNi_1−x LDHs), which both Co(OH)₂ and Ni(OH)₂ exhibit, has been successfully synthesized by a chemical co-precipitation route using polyethylene glycol as the structure-directing reagent. Structural and morphological characterizations were performed using powder X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM). The component and thermal stability of the sample were measured by energy dispersed X-ray spectrometry (EDS), FT-IR and thermal analyses, including thermogravimetry (TG) and differential thermal analysis (DTA). Cyclic voltammogram and galvanostatic charge-discharge testified that the Co_xNi_1−x LDH has a specific capacitance of 1809 F g⁻¹ at a current density of 1 A g⁻¹ and remains at about 90.2% of the initial value after 1000 cycles at a current density of 10 A g⁻¹. The relationship between the chemical composition and the capacitance is discussed.     

Single crystal nanobelts of V3O7·H2O: A lithium intercalation host with a large capacity

In this study, single crystal V₃O₇·H₂O nanobelts were successfully synthesized using a simple hydrothermal route, in which templates or catalysts were absent. The synthesized V₃O₇·H₂O nanobelts are highly crystalline and have lengths up to several tens of micrometers. The width and thickness of the nanobelts are found to be about 30-50 and 30 nm, respectively. A lithium battery using V₃O₇·H₂O nanobelts as the positive electrode exhibits a high initial discharge capacity of 409 mAh g⁻¹, corresponding to the formation of Li_xV₃O₇·H₂O (x = 4.32). Such a high degree of electrochemical performance is attributed to the intrinsic properties of the single-crystalline V₃O₇·H₂O nanobelts.     

Hydrothermal synthesis of binary Ru-Ti oxides with excellent performances for supercapacitors

Hydrous, crystalline, binary (Ru-Ti)O₂·nH₂O with compositions equal to the ratios of metallic ions in the precursor solutions are successfully synthesized by a mild hydrothermal process. The maximum utilization of RuO₂·nH₂O (ca. 793 F/g) occurs at the composition of 60 M% TiO₂·nH₂O although phase separation is clearly found for this TiO₂-enriched binary oxides. The nano-structured architecture with a high BET surface area (ca. 253 m²/g) of the hydrothermal-derived (Ru-Ti)O₂·nH₂O with annealing at 200 °C favors the physical adsorption of water and maintains a high water content which is novel and never found before. Due to this novel nanostructure, the annealed (Ru-Ti)O₂·nH₂O synthesized by means of the hydrothermal process exhibits excellent performances (i.e., high utilization of RuO₂, high power property, and long cycle life) for supercapacitors.     

The key factor determining the anodic deposition of vanadium oxides

This work demonstrates that anodic deposition of vanadium oxide (denoted as VO_x·nH₂O) can be considered as the chemical co-precipitation of V⁵⁺ and V⁴⁺ oxy-/hydroxyl species and the accumulation of V⁵⁺ species at the vicinity of electrode surface is the key factor for the successful anodic deposition of VO_x·nH₂O at a potential much more negative than the equilibrium potential of the oxygen evolution reaction (OER). The results of in situ UV-vis spectra show that the V⁴⁺/V⁵⁺ ratio near the electrode surface can be controlled by varying the applied potential, leading to different, three-dimensional (3D) nanostructures of VO_x·nH₂O. The accumulation of V⁵⁺ species due to V⁴⁺ oxidation at potentials ≥0.4 V (vs. Ag/AgCl) has been found to be very similar to the phenomenon by adding H₂O₂ in the deposition solution. The X-ray photoelectron spectroscopic (XPS) results show that all VO_x·nH₂O deposits can be considered as aggregates consisting of mixed V⁵⁺ and V⁴⁺ oxy-/hydroxyl species with the mean oxidation state significantly increasing with the applied electrode potential.     

Study on the rapid synthesis of LiNi1−xCoxO2 cathode material for lithium secondary battery

LiNi_1−xCo_xO₂ (x = 0, 0.1, 0.2) cathode materials were successfully synthesized by a rheological phase reaction method with calcination time of 0.5 h at 800 °C. All obtained powders are pure phase with α-NaFeO₂ structure (R-3m space group). The samples deliver an initial discharge capacity of 182, 199 and 189 mAh g⁻¹ (25 mA g⁻¹, 4.35-3.0 V), respectively. The reaction mechanism was also discussed, which consists of a series of defect reactions. As a result of these defect reactions, the reaction of forming LiNi_1−xCo_xO₂ takes place in high speed.     

Synthesis and tunable thermal expansion properties of Sc2−xYxW3O12 solid solutions

A new series of rare earth solid solutions Sc_2−xY_xW₃O₁₂ was successfully synthesized by the conventional solid-state method. Effects of doping ion yttrium on the crystal structure, morphology and thermal expansion property of as-prepared Sc_2−xY_xW₃O₁₂ ceramics were investigated by X-ray diffraction (XRD), thermogravimetric analysis (TG), field emission scanning electron microscope (FE-SEM) and thermal mechanical analyzer (TMA). Results indicate that the obtained Sc_2−xY_xW₃O₁₂ samples with Y doping of 0≤x≤0.5 are in the form of orthorhombic Sc₂W₃O₁₂-structure and show negative thermal expansion (NTE) from room temperature to 600 °C; while as-synthesized materials with Y doping of 1.5≤x≤2 take hygroscopic Y₂W₃O₁₂·nH₂O-structure at room temperature and exhibit NTE only after losing water molecules. It is suggested that the obvious difference in crystal structure leads to different thermal expansion behaviors in Sc_2−xY_xW₃O₁₂. Thus it is proposed that thermal expansion properties of Sc_2−xY_xW₃O₁₂ can be adjusted by the employment of Y dopant; the obtained Sc_1.5Y_0.5W₃O₁₂ ceramic shows almost zero thermal expansion and its average linear thermal expansion coefficient is −0.00683×10⁻⁶ °C⁻¹ in the 25–250 °C range.     

One-step electrochemical preparation of the ternary (BixSb1−x)2Te3 thin films on Au(1 1 1): Composition-dependent growth and characterization studies

This study reports on the synthesis of ternary semiconductor (Bi_xSb_1−x)₂Te₃ thin films on Au(1 1 1) using a practical electrochemical method, based on the simultaneous underpotential deposition (UPD) of Bi, Sb and Te from the same solution containing Bi³⁺, SbO⁺, and HTeO₂⁺ at a constant potential. The thin films are characterized by X-ray diffraction (XRD), atomic force microscopy (AFM), energy dispersive spectroscopy (EDS) and reflection absorption-FTIR (RA-FTIR) to determine structural, morphological, compositional and optic properties. The ternary thin films of (Bi_xSb_1−x)₂Te₃ with various compositions (0.0 ≤ x ≤ 1.0) are highly crystalline and have a kinetically preferred orientation at (0 1 5) for hexagonal crystal structure. AFM images show uniform morphology with hexagonal-shaped crystals deposited over the entire gold substrate. The structure and composition analyses reveal that the thin films are pure phase with corresponding atomic ratios. The optical studies show that the band gap of (Bi_xSb_1−x)₂Te₃ thin films could be tuned from 0.17 eV to 0.29 eV as a function of composition.     

Preparation, characterization and electrical conductivity studies of NdYb1−xGdxZr2O7 (0 ≤ x ≤ 1.0) ceramics

Several compositions of NdYb_1−xGd_xZr₂O₇ (0 ≤ x ≤ 1.0) ceramics were prepared by pressureless-sintering method at 1973 K for 10 h in air. The relative density, microstructure and electrical conductivity of NdYb_1−xGd_xZr₂O₇ ceramics were analyzed by the Archimedes method, X-ray diffraction, scanning electron microscopy and impedance plots measurements. NdYb_1−xGd_xZr₂O₇ (0 ≤ x ≤ 0.3) ceramics have a single phase of defect fluorite-type structure, and NdYb_1−xGd_xZr₂O₇ (0.7 ≤ x ≤ 1.0) ceramics exhibit a single phase of pyrochlore-type structure; however, the NdYb_0.5Gd_0.5Zr₂O₇ composition shows mixed phases of both defect fluorite-type and pyrochlore-type structures. The measured values of the grain conductivity obey the Arrhenius relation. The grain conductivity of each composition in NdYb_1−xGd_xZr₂O₇ ceramics gradually increases with increasing temperature from 673 to 1173 K. NdYb_1−xGd_xZr₂O₇ ceramics are oxide-ion conductor in the oxygen partial pressure range of 1.0 × 10⁻⁴ to 1.0 atm at all test temperature levels. The highest grain conductivity value obtained in this work is 1.79 × 10⁻² S cm⁻¹ at 1173 K for NdYb_0.3Gd_0.7Zr₂O₇ composition.     

NiO-based composite electrode with RuO2 for electrochemical capacitors

NiO/RuO₂ composite materials were prepared for use in electrochemical capacitors (ECs) by co-precipitation method followed by heat treatment. X-ray diffraction (XRD) spectra indicated that no new structural materials were formed and ruthenium oxide particles were coated by NiO particles. RuO₂ partly introduced into NiO-based electrode had improved its electrochemical performance and capacitive properties by using electrochemical measurements. A maximum specific capacitance of 210 F/g was obtained for NiO-based composite electrode with 10 wt.% RuO₂ in the voltage range from −0.4 to 0.5 V in 1 mol/l KOH solution. By comparison of effect of modified modes on the specific capacitance, chemically modified composite electrodes had more stable cycling properties than those of physically modified electrodes. After 200 cycles, specific capacitance of NiO-based chemical composite electrode with 5 wt.% RuO₂ kept 95% above, while that of physical electrode was only 79% of initial specific capacitance.     

Synthesis and electrochemical performance of novel loose structured submicro/micro-sized NiSnx alloy composites for lithium batteries

An effective method of carbothermal reduction was employed to prepare spherical microcrystal NiSn_x alloy powders from oxides of Sn and Ni used as anode materials for Li-ion battery. According to XRD, SEM and TEM analysis, the synthesized spherical NiSn_x powders show a loose submicro/micro-sized structure and a multi-phase composition. The prepared NiSn_x alloy composite electrode exhibits a stable discharge capacity of electrode is ca. 380 mAh g⁻¹ at constant current density of 50 mA g⁻¹, and can be retained at 350 mAh g⁻¹ after 25 cycles. Moreover, NiSn_x alloys exhibit excellent high rate performance, i.e. stable discharge capacities of 300-310 mAh g⁻¹ and the coulombic efficiencies of 97.5-99.5% have been obtained at the current density of 500 mA g⁻¹. The loose submicro-sized particle structural characteristic and the Ni addition in Sn matrix should be responsible for the improvement of cycling stability of NiSn_x electrode. The carbothermal reduction method is simple, low-cost and mass-productive, which should be viable to other alloy composite materials system of rechargeable lithium ion batteries.     

Microwave-polyol synthesis of nanocrystalline ruthenium oxide nanoparticles on carbon nanotubes for electrochemical capacitors

The ruthenium oxide nanoparticles dispersed on multi-wall carbon nanotubes (CNTs) were successfully synthesized via microwave-polyol process combined with forced hydrolysis without additional thermal oxidation or electrochemical oxidation treatment. The HRTEM, Raman spectra and TGA curve indicate that CNTs were uniformly coated with crystalline and partially hydrous RuO₂·0.64H₂O nanoparticles of 2 nm diameter and the loading amount of ruthenium oxide in the composite could be controlled up to 70 wt.%. The specific capacitance was 450 Fg⁻¹ of ruthenium oxide/CNT composite electrode with 70 wt.% ruthenium oxide at the potential scan rate of 10 mV s⁻¹ and it decreased to 362 Fg⁻¹ by 18% at 500 mV s⁻¹. The specific capacitance of ruthenium oxide in the composite was 620 Fg⁻¹ of ruthenium oxide at 10 mV s⁻¹. The ruthenium oxide nanoparticles in ruthenium oxide/CNT nanocomposite electrode had a high ratio of outer charge to total charge of 0.81, which confirmed its high-rate capability of the composite through the preparation of the nano-sized ruthenium oxide particles on the external surface of CNTs.     

Evolution of the local structure and electrochemical properties of spinel LiNixMn2−xO4 (0 ≤ x ≤ 0.5)

A series of Ni substituted spinel LiNi_xMn_2−xO₄ (0 ≤ x ≤ 0.5) have been synthesized to study the evolution of the local structure and their electrochemical properties. X-ray diffraction showed a few Ni cations moved to the 8a sites in heavily substituted LiNi_xMn_2−xO₄ (x ≥ 0.3). X-ray photoelectron spectroscopy confirmed Ni²⁺ cations were partially oxidized to Ni³⁺. The local structures of LiNi_xMn_2−xO₄ were studied by analyzing the and A_1g Raman bands. The most compact [Mn(Ni)O₆] octahedron with the highest bond energy of Mn(Ni)O was found for LiNi_0.2Mn_1.8O₄, which showed a Mn(Ni)O average bond length of 1.790 Å, and a force constant of 2.966 N cm⁻¹. Electrolyte decomposition during the electrochemical charging processes increased with Ni substitution. The discharge capacities at the 4.1 and 4.7 V plateaus obeyed the linear relationships with respect to the Ni substitution with the slopes of −1.9 and +1.9, which were smaller than the theoretical values of −2 and +2, respectively. The smaller slopes could be attributed to the electrochemical hysteresis and the presence of Ni³⁺ in the materials.