Electrochemical activity of Geobacter sulfurreducens biofilms on stainless steel anodes

Stainless steel was studied as anode for the biocatalysis of acetate oxidation by biofilms of Geobacter sulfurreducens. Electrodes were individually polarized at different potential in the range −0.20 V to +0.20 V vs. Ag/AgCl either in the same reactor or in different reactors containing acetate as electron donor and no electron acceptor except the working electrode. At +0.20 V vs. Ag/AgCl, the current increased after a 2-day lag period up to maximum current densities around 0.7 A m⁻² and 2.4 A m⁻² with 5 mM and 10 mM acetate, respectively. No current was obtained during chronoamperometry (CA) at potential values lower than 0.00 V vs. Ag/AgCl, while the cyclic voltammetries (CV) that were performed periodically always detected a fast electron transfer, with the oxidation starting around −0.25 V vs. Ag/AgCl. Epifluorescent microscopy showed that the current recorded by chronoamperometry was linked to the biofilm growth on the electrode surface, while CVs were more likely linked to the cells initially adsorbed from the inoculum. A model was proposed to explain the electrochemical behaviour of the biofilm, which appeared to be controlled by the pioneering adherent cells playing the role of “electrochemical gate” between the biofilm and the electrode surface.     

Electroless immobilization and electrochemical characteristics of nickel hexacyanoruthenate film at an aluminum substrate

The surface of an aluminum (Al) electrode was modified with a thin film of nickel hexacyanoruthenate (NiHCR) as a novel electrode material. The modification procedure of Al surface, includes two consecutive procedures: (i) the electroless deposition of metallic nickel on the Al electrode surface from NiCl₂ solution, and (ii) the chemical transformation of deposited nickel to nickel hexacyanoruthenate films in solution of 20 mM K₃[Ru(CN)₆] + 0.5 M KNO₃. Cyclic voltammogram of the modified Al electrode showed a well-defined redox reaction due to [Ni^IIRu^III/II(CN)₆]^1−/2− system. The effects of different supporting electrolytes and solution pH were studied on the electrochemical characteristics of the modified electrode. The diffusion coefficients of K⁺ and Na⁺ cations in the film (D), the transfer coefficient (α), and the charge transfer rate constant at the modifying film/electrode interface (k_s), were calculated in the presence of both K⁺ and Na⁺ cations. The stability of the modified electrode was investigated under various experimental conditions.     

Electrochemical generation of hydrogen peroxide using surface area-enhanced Ti-mesh electrodes

Ti-mesh electrodes coated with Ti were obtained by using an electrophoretic deposition (EPD) method. The Ti coating was porous and showed a good adherence to the Ti-mesh surface, due to sintering of Ti particles during thermal treatment at 900 °C. The Ti-coated mesh electrode has a BET surface area of 3.5 m²/g, about four times larger than that of the bare electrode. The surface area-enhanced Ti-mesh electrode was applied in electrical generation of hydrogen peroxide. It was shown that the rate of hydrogen peroxide generation increased drastically compared to the fresh electrode, since the larger electrode surface area enhanced not only current density, but also the oxygen mass transfer rate.     

Impedance spectroscopy data for S2O8 anion electroreduction at Bi(1 1 1) plane

Electroreduction kinetics of the peroxodisulfate anions on the electrochemically polished Bi(1 1 1) single crystal electrode has been studied by impedance spectroscopy. Influence of the electrode potential, reaction intermediates, base electrolyte and reactant concentrations on the kinetic parameters of electroreduction has been established. Systematic analysis of the fitting results demonstrates the noticeable influence of adsorption of the reaction intermediate or reactant on the electroreduction rate of the S₂O₈²⁻ anions at the Bi(1 1 1) electrode. In the region of so-called “current pits” in the cyclic voltammetry curves, obtained by rotating disc electrode method, the mixed kinetics, i.e. the adsorption and “true” charge transfer limited steps have been established by impedance spectroscopy.     

PEM fuel cell reaction kinetics in the temperature range of 23-120 °C

The performance of a Nafion 112 based proton exchange membrane (PEM) fuel cell was tested at a temperature range from 23 °C to 120 °C. The fuel cell polarization curves were divided into two different ranges based on current density, namely, <0.4 A/cm² and >0.4 A/cm², respectively. These two ranges were treated separately with respect to electrode kinetics and mass transfer. In the high current density range, a linear increase in membrane electrode assembly (MEA) power density with increasing temperature was observed, indicating the advantages of high temperature operation.Simulation based on electrode reaction kinetic theory, experimental polarization curves, and measured cathodic apparent exchange current densities all gave temperature dependent apparent exchange current densities. Both the calculated partial pressures of O₂ and H₂ gas in the feed streams and the measured electrochemical Pt surface areas (EPSAs) decrease with increasing temperature. They were also used to obtain the intrinsic exchange current densities. A monotonic increase of the intrinsic exchange current densities with increasing temperature in the range of 23-120 °C was observed, suggesting that increasing the temperature does promote intrinsic kinetics of fuel cell reactions.There are two sets of cathode apparent exchange current densities obtained, one set is for the low current density range, and the other is for the high current density range. The different values of cathode current densities in the two current density ranges can be attributed to the different states of the cathode Pt catalyst surface. In the low current density range, the cathode catalyst surface is a Pt/PtO, and in the high current density range, the catalyst surface becomes pure Pt.     

Preparation and electrochemistry of cadmium pentacyanonitrosylferrate film modified glassy carbon electrode

A glassy carbon (GC) electrode surface was modified with a cadmium pentacyanonitrosylferrate (CdPCNF) film as a novel electrode material. The modification procedure of the GC surface includes two consecutive procedures: (i) the electrodeposition of metallic cadmium on the GC electrode surface from a CdCl₂ solution and (ii) the chemical transformation of the deposited cadmium to the CdPCNF films in 0.05 M Na₂[Fe(CN)₅NO] + 0.5 M KNO₃ solution. The modified GC electrode showed a well-defined redox couple due to [Cd^IIFe^III/II(CN)₅NO]^0/−1 system. The effects of supporting electrolytes and solution pH were studied on the electrochemical behavior of the modified electrode. The diffusion coefficients of alkali-metal cations in the film (D), the transfer coefficient (α) and the charge transfer rate constant at the modifying film | electrode interface (k_s), were calculated in the presence of various alkali-metal cations. The stability of the modified electrode was investigated under various experimental conditions.     

Electrocatalytic oxidation of l-cysteine with a stable copper-cobalt hexacyanoferrate electrochemically modified carbon paste electrode

A stable composition of hybrid copper-cobalt hexacyanoferrate (Cu-CoHCF) film was electrodeposited on a carbon paste electrode (CPE). There are a few reports for using this hybrid as a mediator, but all of them require almost 12 h conditioning time before usage. Contrary to previous reports this electrode does not require any conditioning and can be used immediately after film formation. The electrocatalytic activity of this film was investigated and showed a good electrocatalytic effect for oxidation of l-cysteine (Cys) in phosphate buffer solution (PBS) in pH range of 1-7. A linear range of 6 μM to 1 mM of Cys and an experimental detection limit of 5 μM of Cys were obtained using cyclic voltammetry method. The diffusion coefficient of Cys and catalytic rate constant for electrocatalytic reaction were also calculated. The major problem reported in electro oxidation of Cys is poisoning of electrode surface with reaction product, but in this study oxidation of Cys had no significant fouling effect on the modified electrode surface for the concentrations below 0.5 mM of Cys.     

Electrocatalytic hydrazine oxidation on quinizarine modified glassy carbon electrode

The electrocatalytic oxidation of hydrazine has been studied on glassy carbon modified by electrodeposition of quinizarine, using cyclic voltammetry and chronoamperometry techniques. It has been shown that the oxidation of hydrazine to nitrogen occurs at a potential where oxidation is not observed at the bare glassy carbon electrode. The apparent charge transfer rate constant and transfer coefficient for electron transfer between the electrode surface and immobilized quinizarine were calculated as 4.44 s⁻¹ and 0.66, respectively. The heterogenous rate constant for oxidation of hydrazine at the quinizarine modified electrode surface was also determined and found to be about 4.83 × 10³ M⁻¹ s⁻¹. The diffusion coefficient of hydrazine was also estimated as 1.1 × 10⁻⁶ cm² s⁻¹ for the experimental conditions, using chronoamperometry.     

The reduction of l-cystine hydrochloride at stationary and rotating disc mercury electrodes

The kinetics of l-cystine hydrochloride reduction have been studied at a mercury-plated copper rotating disc electrode (RDE) and at a stationary mercury disc electrode (SMDE) in 0.1 mol dm⁻³ HCl at 298 K. The reduction of the disulphide is irreversible and hydrogen evolution is the major side reaction. In contrast to steady state electrode kinetic studies at a mercury drop electrode (which shows a well-defined limiting current), the mercury-plated Cu RDE shows overlap between disulphide reduction and hydrogen evolution. These effects are attributable to strong reactant adsorption with a calculated surface coverage close to 100%. A Tafel slope of −185 mV per decade is found with a cathodic transfer coefficient of 0.32 and a formal rate constant of 6.7 × 10⁻⁹ m s⁻¹. The relative merits of steady state voltammetry at a mercury-plated copper RDE and linear sweep voltammetry at the SMDE are discussed, as is the mechanism of l-cysteine hydrochloride formation.     

Enhanced mass transport to a reticulated vitreous carbon rotating cylinder electrode using jet flow

The mass transport characteristics of a porous, rotating cylinder electrode (RCE, 1.0 cm diameter; 0.5, 0.9 or 1.2 cm long; 1.25, 2.25, 3.00 cm³ overall volume; 250-2000 rpm speed) fabricated from reticulated vitreous carbon (RVC, 60 ppi or 100 ppi) were investigated. The deposition of copper from an acid sulfate electrolyte (typically, deoxygenated 1 mM CuSO₄ in pH 2, 0.5 M Na₂SO₄ at 298 K) was used as a test reaction. The effect of a jet flow of electrolyte towards the electrode and the introduction of polypropylene baffles in the electrochemical cell were studied at controlled rotation rates of the RCE. The product of mass transport coefficient and volumetric electrode area (k_mA_e) is related to the rotation speed of the electrode. For the 60 ppi RVC RCE, the jet electrolyte flow (3.5 cm³ s⁻¹) enhanced the mass transport rates by a factor of 1.46 at low rotation speeds; this factor was reduced to 1.08 at high rotation speeds. For a 100 ppi electrode, the enhanced mass transport decreased from 1.26 to 1.03 at low and high rotation rates, respectively. Under the experimental conditions, baffles showed little effect on the mass transport rates to the RVC RCE. Mass transport to jet flow at an RVC RCE is compared to other RCEs using dimensionless group correlation.     

Microwave activation of electrochemical processes: High temperature phenol and triclosan electro-oxidation at carbon and diamond electrodes

The electrochemical oxidation of phenolic compounds in aqueous media is known to be affected by the formation of electro-polymerized organic layers which lead to partial or complete electrode blocking. In this study the effect of high intensity microwave radiation applied locally at the electrode surface is investigated for the oxidation of phenol and triclosan in alkaline solution at a 500 μm diameter glassy carbon or at a 500 μm × 500 μm boron-doped diamond electrode. The temperature at the electrode surface and mass transport enhancement are determined by calibration with the Fe(CN)₆^3−/4− redox system in aqueous 0.3 M NaOH and 0.2 NaCl (pH 12) solution. The calibration shows that strong thermal and mass transport effects occur at both glassy carbon and boron-doped diamond electrodes. The average electrode temperature reaches up to 390 K and mass transport enhancements of more than 20-fold are possible. For the phenol electro-oxidation at glassy carbon electrodes and at a concentration below 2 mM a multi-electron oxidation (ca. 4 electrons) occurs in the presence of microwave radiation. For the electro-oxidation of the more hydrophobic triclosan only the one-electron oxidation occurs. Although currents are enhanced in presence of microwave radiation, rapid blocking of the electrode surface in particular at high phenol concentrations still occurs.     

Modelling of the concentration-time relationship based on global diffusion-charge transfer parameters in a flow-by reactor with a 3D electrode

A concentration versus time relationship model based on the isothermal diffusion-charge transfer mechanism was developed for a flow-by reactor with a three-dimensional (3D) reticulated vitreous carbon (RVC) electrode. The relationship was based on the effectiveness factor (η) which lead to the simulation of the concentration decay at different electrode polarisation conditions, i.e. −0.1, −0.3 and −0.59 V versus SCE; the charge transfer process was used for the former and mix and a mass transport control was used for the latter. Charge transfer and mass transport parameters were estimated from experimental data using Electrochemical Impedance Spectroscopy (EIS) and Linear Voltammetry (LV) techniques, respectively.     

Diffusional mass transfer model for the adsorption of food dyes on chitosan films

The adsorption kinetics of erythrosine B and indigo carmine on chitosan films was studied by a diffusional mass transfer model. The experimental curves were obtained in batch system under different conditions of stirring rate (80–200 rpm) and initial dye concentration (20–100 mg L⁻¹). For the model development, external mass transfer and intraparticle diffusion steps were considered and the specific simplifications were based on the system characteristics. The proposed diffusional mass transfer model agreed very well with the experimental curves, indicating that the surface diffusion was the rate limiting step. The external mass transfer coefficient (k_f) was dependent of the operating conditions and ranged from 1.32 × 10⁻⁴ to 2.17 × 10⁻⁴ m s⁻¹. The values of surface diffusion coefficient (D_s) increased with the initial dye concentration and were in the range from 0.41 × 10⁻¹⁴ to 22.90 × 10⁻¹⁴ m² s⁻¹. The Biot number ranged from 17.0 to 478.5, confirming that the intraparticle diffusion due to surface diffusion was the rate limiting step in the adsorption of erythrosine B and indigo carmine on chitosan films.     

Renewable-surface sol-gel derived carbon ceramic-modified electrode fabricated by a newly synthesized polypyridil and phosphine Ru (II) complex and its application as an amperometric sensor for hydrazine

A chemically modified carbon ceramic composite electrode (CCE) containing Dichloro{(8, 9-dimethyl-dipyridio [2,3-a;2′,3′-c] phenazine-κ²-N,N′) bis(triphenylphosphine-κ-P)}ruthenium (II) complex which synthesized newly was constructed by the sol-gel technique. Electrochemical behavior and stability of modified CCE were investigated by cyclic voltammetry. The electrocatalytic activity of CCE was investigated and showed a good effect for oxidation of hydrazine in phosphate buffer solution (PBS). A linear concentration range of 6 μM to 1.2 mM of hydrazine with an experimental detection limit of 1 μM of hydrazine was obtained. The diffusion coefficient of hydrazine and its catalytic rate constant for electrocatalytic reaction along with the apparent electron transfer rate constant (k_s) and transfer coefficient (α) were also determined.The modified carbon ceramic electrode doped with this new Ru-complex showed good reproducibility, short response time (t < 2 s), remarkable long-term stability (>3 month) and especially good surface renewability by simple mechanical polishing.The results showed that this electrode could be used as an electrochemical sensor for determination of hydrazine in real water samples used in Fars Power Plant Station, including its heat recovery steam generator (HRSG) water (at different operational condition), cooling system and clean waste water.     

Nanomolar detection of rutin based on adsorptive stripping analysis at single-sided heated graphite cylindrical electrodes with direct current heating

A single-sided heated graphite cylindrical electrode (ss-HGCE) was designed. Compared to previous alternative current (AC) heating, much simpler and cheaper direct current (DC) heating supplier was adopted for the first time to perform adsorptive accumulation of rutin at ss-HGCE at elevated electrode temperature. This offers great promise for low cost, miniaturization and high compatibility with portability. The square wave voltammetry (SWV) stripping peak current was enhanced with increasing the electrode temperature only during preconcentration step. This enhancement was contributed to the forced thermal convection induced by heating the electrode rather than the bulk solution, which is able to improve mass transfer and facilitate adsorption hence enhance stripping response. A detection limit of 1.0 × 10⁻⁹ M (S/N = 3) could be obtained at an electrode temperature of 48 °C during 5 min accumulation, one magnitude lower than that at 28 °C (room temperature). This is the lowest value at carbon-based electrodes for rutin determination as we know. Such novel method was also successfully used to determine rutin in pharmaceutical tablets.     

An electrochemical study of neutral red-DNA interaction

Electrochemical methods were used to investigate the interaction of neutral red (NR) with double-stranded calf thymus DNA, in solution as well as using a DNA-modified glassy carbon (GC-DNA) electrode. The results were compared with those obtained from bare glassy carbon (GC) electrode. The formal potential of NR was more positive when GC-DNA electrode was used although the rate of heterogeneous electron transfer is as high as that of using GC electrode. GC-DNA electrode enables preconcentration of NR for chosen times on the electrode surface, despite the fact that the mass transfer effects in the thin DNA layer adsorbed on the surface was still observed using cyclic voltammetry and electrochemical impedance spectroscopy techniques. Parameters, such as the diffusion coefficient of NR, binding site size in base pairs and the ratio of the binding constants for the oxidized and reduced forms of the bound species were obtained. A binding isotherm for NR at GC-DNA electrode was obtained from coulometric titrations and gave an affinity constant equal to 2.76 × 10⁴ L mol⁻¹. From the studies of the interaction in solution, the diffusion coefficient of free and DNA-bound NR, binding constant and binding site size of the DNA-NR complex was also obtained simultaneously by non-linear fitting analysis of voltammetric data.     

An enzyme-based microfluidic biofuel cell using vitamin K3-mediated glucose oxidation

Viamin K₃-modified poly-l-lysine (PLL-VK₃) was synthesized and used as the electron transfer mediator during catalytic oxidation of NADH by diaphorase (Dp) at the anode of biofuel cell. PLL-VK₃ and Dp were co-immobilized on an electrode and then coated with NAD⁺-dependent glucose dehydrogenase (GDH). The resulting enzymatic bilayer (abbreviated PLL-VK₃/Dp/GDH) catalyzed glucose oxidation. Addition of carbon black (Ketjenblack, KB) into the bilayer enlarged the effective surface area of the electrode and consequentially increased the catalytic activity. An oxidation current of ca. 2 mA cm⁻² was observed when the electrochemical cell contained a stirred 30 mM glucose, 1.0 mM NAD⁺, pH 7.0 phosphate-buffered electrolyte solution. The performance of glucose/O₂ biofuel cells, constructed as fluidic chips with controllable fuel flow and containing a KB/PLL-VK₃/Dp/GDH-coated anode and an Ag/AgCl or a polydimethylsiloxane-coated Pt cathode, were evaluated. The open circuit voltage of the cell with the PDMS-coated Pt cathode was 0.55 V and its maximum power density was 32 μW cm⁻² at 0.29 V when a pH 7.0-buffered fuel containing 5.0 mM glucose and 1.0 mM NAD⁺ was introduced into the cell at a flow rate of 1.0 mL min⁻¹. The cell's output increased as the flow rate increased. During 18 h of continuous operation of the cell with a load of 100 kΩ, the output current density declined by ca. 50%, probably due to swelling of the enzyme bilayer.     

Modification of glassy carbon electrode with multi-walled carbon nanotubes and iron(III)-porphyrin film: Application to chlorate, bromate and iodate detection

In this study, multi-wall carbon nanotubes (MWCTs) is evaluated as a transducer, stabilizer and immobilization matrix for the construction of amperometric sensor based on iron-porphyrin. 5,10,15,20-Tetraphenyl-21H,23H-porphine iron(III) chloride (Fe(III)P) adsorbed on MWCNTs immobilized on the surface of glassy carbon electrode. Cyclic voltammograms of the Fe(III)P-incorporated-MWCNTs indicate a pair of well-defined and nearly reversible redox couple with surface confined characteristics at wide pH range (2-12). The surface coverage (Γ) and charge transfer rate constant (k_s) of Fe(III)P immobilized on MWCNTs were 7.68 × 10⁻⁹ mol cm⁻² and 1.8 s⁻¹, respectively, indicating high loading ability of MWCNTs for Fe(III)P and great facilitation of the electron transfer between Fe(III)P and carbon nanotubes immobilized on the electrode surface. Modified electrodes exhibit excellent electrocatalytic activity toward reduction of ClO₃⁻, IO₃⁻ and BrO₃⁻ in acidic solutions. The catalytic rate constants for catalytic reduction of bromate, chlorate and iodate were 6.8 × 10³, 7.4 × 10³ and 4.8 × 10² M⁻¹ s⁻¹, respectively. The hydrodynamic amperometry of rotating-modified electrode at constant potential versus reference electrode was used for detection of bromate, chlorate and iodate. The detection limit, linear calibration range and sensitivity for chlorate, bromate and iodate detections were 0.5 μM, 2 μM to 1 mM, 8.4 nA/μM, 0.6 μM, 2 μM to 0.15 mM, 11 nA/μM, and 2.5 μM, 10 μM to 4 mM and 1.5 nA/μM, respectively. Excellent electrochemical reversibility of the redox couple, good reproducibility, high stability, low detection limit, long life time, fast amperometric response time, wide linear concentration range, technical simplicity and possibility of rapid preparation are great advantages of this sensor. The obtained results show promising practical application of the Fe(III)P-MWCNTs-modified electrode as an amperometric sensor for chlorate, iodate and bromate detections.     

Ni(II)-quercetin complex modified multiwall carbon nanotube ionic liquid paste electrode and its electrocatalytic activity toward the oxidation of glucose

A modified electrode Ni(II)-Qu-MWCNT-IL-PE has been fabricated by electrodepositing Ni(II)-quercetin [Ni(II)-Qu] complex on the surface of multi-wall carbon nanotube ionic liquid paste electrode (MWCNT-IL-PE) in alkaline solution. The Ni(II)-Qu-MWCNT-IL-PE exhibits the characteristic of improved reversibility and enhanced current responses of the Ni(III)/Ni(II) couple compared with Ni(II)-Qu-MWCNT-PE. It also shows good electrocatalytic activity toward the oxidation of glucose. Kinetic parameters such as the electron transfer coefficient α, rate constant k_s of the electrode reaction and the catalytic rate constant k_cat of the catalytic reaction are determined. Moreover, the catalytic current presents linear dependence on the concentration of glucose from 5.0 μM to 2.8 mM, with a detection limit of 1.0 μM by amperometry. The modified electrode for glucose determination is of the property of simple preparation, good stability, fast response and high sensitivity.     

Poly(indole-6-carboxylic acid) and tetracyanoquinodimethane-modified electrode for selective oxidation of dopamine

Poly(indole-6-carboxylic acid) (PICA) was synthesized electrochemically over glassy carbon electrode (GCE) through potentiodynamic mode of polymerization. The resulting polymer was soluble in Tris-HCl buffer (pH 7.0). The processable polymer was cast over desired electrode surface along with organic redox mediator tetracyanoquinodimethane (TCNQ) as an electron transfer relay using Nafion^®. Nafion^® was used to solubilize TCNQ as well as to introduce permselectivity to the blend of polymer and TCNQ. The above blend was cast over GCE and characterized by cyclic voltammetry followed by its application in electrochemical sensing of dopamine (DA) and ascorbic acid (AA). The modified electrode was found to be selective for DA analysis. The lowest detection limit of DA sensing was found to be 4 μМ with a sensitivity of 18 μA ± 6 nA/mM of DA.