A novel lithium intercalation compound based on the layered structure of lithium nitridonickelates Li3−2xNixN

New lithium nickel nitrides Li_3−2xNi_xN (0.20 ≤ x ≤ 0.60) have been prepared and investigated as negative electrode in the 0.85/0.02 V potential window. These materials are prepared from a Ni/Li₃N mixture at 700 °C under a nitrogen flow. Their structural characteristics as well as their electrochemical behaviour are investigated as a function of the nickel content. For the first time are reported here the electrochemical properties of a lithium intercalation compound based on a layered nitride structure. The Li_3−2xNi_xN compounds can be reversibly reduced and oxidized around 0.5 V versus Li/Li⁺ leading to specific capacities in the range 120-160 mAh/g depending on the nickel content and the C rate. Due to a large number of lithium vacancies, the structural stability provides an excellent capacity retention of the specific capacity upon cycling.     

Synthesis, characterization and electrochemical properties of a novel triphosphate LiFe2P3O10

A novel lithium iron phosphate has been synthesized by a solution route at moderate temperature. The structure was determined from powder by XRD, HRTEM and SAED experiments. LiFe₂P₃O₁₀ tripolyphosphate crystallizes in the monoclinic system, space group P2₁/m, with lattice constants a = 4.597(7) Å, b = 8.566(4) Å, c = 9.051(4) Å, β = 97.47° and Z = 2. Internal and external vibrational modes (Raman and FTIR) show that the dominant spectral features come from the (P₃O₁₀)⁵⁻ oxo-anions displaying internal and external modes along with the P-O-P bridging modes. Magnetic measurements are consistent with the high-spin configuration of Fe²⁺ cation with an effective magnetic moment 5.51 μ_B. A weak antiferromagnetic ordering is observed below the Néel temperature at T_N = 19 K. Electron paramagnetic resonance spectroscopy confirms this electronic configuration and provides evidence of the presence of a carbonaceous layer onto the particle surface. Electrochemical measurements were carried out in lithium cells with LiPF₆-EC-DEC electrolyte at 25 °C. The material delivered a capacity 70 mAh/g in the voltage range 2.7-3.9 V, close to the theoretical value (72 mAh/g). The resulting cyclic voltammogram indicates a stable structure with a good reversibility with the redox peaks at 3.26 and 3.13 V vs. Li⁰/Li⁺.     

Preparation and characterization of novel spinel Li4Ti5O12−xBrx anode materials

Br-doped Li₄Ti₅O₁₂ in the form of Li₄Ti₅O_12−xBr_x (0 ≤ x ≤ 0.3) compounds were successfully synthesized via solid state reaction. The structure and electrochemical properties of the spinel Li₄Ti₅O_12−xBr_x (0 ≤ x ≤ 0.3) materials were investigated. The Li₄Ti₅O_12−xBr_x (x = 0.2) presents the best discharge capacity among all the samples, and shows better reversibility and higher cyclic stability compared with pristine Li₄Ti₅O₁₂, especially at high current rates. When the discharge rate was 0.5 C, the Li₄Ti₅O_12−xBr_x (x = 0.2) sample presented the excellent discharge capacity of 172 mAh g⁻¹, which was very close to its theoretical capacity (175 mAh g⁻¹), while that of the pristine Li₄Ti₅O₁₂ was 123.2 mAh g⁻¹ only.     

Electrochemical properties of TiP2O7 and LiTi2(PO4)3 as anode material for lithium ion battery with aqueous solution electrolyte

Some polyanionic compounds, e.g. TiP₂O₇ and LiTi₂(PO₄)₃ with 3D framework structure were proposed to be used as anodes of lithium ion battery with aqueous electrolyte. The cyclic voltammetry properties TiP₂O₇ and LiTi₂(PO₄)₃ suggested that Li-ion de/intercalation reaction can occur without serious hydrogen evolution in 5 M LiNO₃ aqueous solution. The TiP₂O₇ and LiTi₂(PO₄)₃ give capacities of about 80 mAh/g between potentials of −0.50 V and 0 V (versus SHE) and 90 mAh/g between −0.65 V and −0.10 V (versus SHE), respectively. A test cell consisting of TiP₂O₇/5 M LiNO₃/LiMn₂O₄ delivers approximately 42 mAh/g (weight of cathode and anode) at average voltage of 1.40 V, and LiTi₂(PO₄)₃/5 M LiNO₃/LiMn₂O₄ delivers approximately 45 mAh/g at average voltage of 1.50 V. Both as-assembled cells suffered from short cycle life. The capacity fading may be related to deterioration of anode material.     

Electrochemical and thermal studies of Li[NixLi(1/3−2x/3)Mn(2/3−x/3)]O2 (x = 1/12, 1/4, 5/12, and 1/2)

Samples of the layered cathode materials, Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ (x = 1/12, 1/4, 5/12, and 1/2), were synthesized at 900 °C. Electrodes of these samples were charged in Li-ion coin cells to remove lithium. The charged electrode materials were rinsed to remove the electrolyte salt and then added, along with EC/DEC solvent or 1 M LiPF₆ EC/DEC, to stainless steel accelerating rate calorimetry (ARC) sample holders that were then welded closed. The reactivity of the samples with electrolyte was probed at two states of charge. First, for samples charged to near 4.45 V and second, for samples charged to 4.8 V, corresponding to removal of all mobile lithium from the samples and also concomitant release of oxygen in a plateau near 4.5 V. Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples with x = 1/4, 5/12 and 1/2 charged to 4.45 V do not react appreciably till 190 °C in EC/DEC. Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples charged to 4.8 V versus Li, across the oxygen release plateau, start to significantly react with EC/DEC at about 130 °C. However, their high reactivity is similar to that of Li_0.5CoO₂ (4.2 V) with 1 μm particle size. Therefore, Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples showing specific capacity of up to 225 mAh/g may be acceptable for replacing LiCoO₂ (145 mAh/g to 4.2 V) from a safety point of view, if their particle size is increased.     

An investigation of intercalation-induced stresses generated during lithium transport through sol-gel derived LixMn2O4 film electrode using a laser beam deflection method

The stress changes Δσ generated during lithium transport through the sol-gel derived Li_xMn₂O₄ film electrodes annealed at 773 and 873 K were quantitatively determined as a function of the lithium stoichiometry x using a laser beam deflection method (LBDM). Δσ generated during a real potential step between an initial electrode potential and a final applied potential was uniquely specified by the Δσ versus x curve. The Li_xMn₂O₄ film annealed at 773 K for 24 h (low temperature (LT)-Li_xMn₂O₄) showed larger capacity than the Li_xMn₂O₄ film annealed at 873 K for 6 h (high temperature (HT)-Li_xMn₂O₄) and this result is ascribed to the fact that the smaller the grain size is, the more increases the electrochemically active area of the film electrode. From the analysis of the normalised Δσ transient measured simultaneously along with the cyclic voltammogram in the potential range of 2.5-3.4 VLi/Li⁺, it is found that normalised Δσ generated in the LT-Li_xMn₂O₄ was smaller than that in the HT-Li_xMn₂O₄ during the lithium intercalation/de-intercalation around 3.0 VLi/Li⁺ region. This result gives an experimental evidence for the fact that the Jahn-Teller distortion is suppressed by the increase in the average oxidation state of manganese with decreasing in annealing temperature.     

Hydrothermal synthesis of Li4Ti5O12 microsphere with high capacity as anode material for lithium ion batteries

Lithium titanate (Li₄Ti₅O₁₂) microsphere has been successfully synthesized by a hydrothermal method. X-ray diffraction (XRD) and scanning electron microscope (SEM) are used to characterize the structure and morphology of the prepared Li₄Ti₅O₁₂ crystallites. The results show that the as-synthesized powders exhibit outstanding rate capacities and excellent cycling performance. The first discharge capacity at 0.1 C is 172.5 mAh g⁻¹, which is close to the theoretical capacity of 175 mAh/g. After 50 cycles, the efficiency of the synthesized Li₄Ti₅O₁₂ still retains up to 92.8% at 0.1 C and 95.2% at 0.5 C of its initial value, which present a promising applications as anode materials for lithium ion batteries in hybrid and plug-in hybrid electric vehicles.     

Effect of K2O on structure-property relationships and phase transformations in Li2O-SiO2 glasses

Glass compositions with formula (71.78 − x)SiO₂-2.63Al₂O₃-(2.63 + x)K₂O-23.7Li₂O (mol.%, x = 0-10) and SiO₂/Li₂O molar ratios far beyond that of stoichiometric lithium disilicate (Li₂Si₂O₅) were prepared by conventional melt-quenching technique to investigate the influence of K₂O content on structural transformations and devitrification behaviour of glasses in the Li₂O-SiO₂ system. The scanning electron microscopy (SEM) examination of as cast non-annealed glasses revealed the presence of nanosized droplets in glassy matrices suggesting occurrence of liquid-liquid phase separation. An overall trend towards depolymerization of the silicate glass network with increasing K₂O content was demonstrated by employing magic angle spinning-nuclear magnetic resonance (MAS-NMR) spectroscopy. The distribution of structural units in the experimental glasses was estimated using ²⁹Si MAS-NMR spectroscopy suggesting the appearance of Q², enhancement of Q³ and diminishing of Q⁴ groups with increasing K₂O contents. X-ray diffraction (XRD) and differential thermal analysis (DTA) were used to assess the influence of K₂O on devitrification process and formation of lithium disilicate (Li₂Si₂O₅) and/or lithium metasilicate (Li₂SiO₃) crystalline phases.     

Low temperature solid-state synthesis routine and mechanism for Li3V2(PO4)3 using LiF as lithium precursor

Monoclinic lithium vanadium phosphate, Li₃V₂(PO₄)₃, has been successfully synthesized using LiF as lithium source. The one-step reaction with stoichiometric composition and relative lower sintering temperature (700 °C) has been used in our experimental processes. The solid-state reaction mechanism using LiF as lithium precursor has been studied by X-ray diffraction and Fourier transform infrared spectra. The Rietveld refinement results show that in our product sintered at 700 °C no impurity phases of VPO₄, Li₅V(PO₄)₂F₂, or LiVPO₄F can be detected. The solid-state reaction using Li₂CO₃ as Li-precursor has also been carried out for comparison. X-ray diffraction patterns indicate that impurities as Li₃PO₄ can be found in the product using Li₂CO₃ as Li-precursor unless the sintering temperatures are higher than 850 °C. An abrupt particle growth (about 2 μm) has also been observed by scanning electron microscope for the samples sintered at higher temperatures, which can result in a poor cycle performance. The product obtained using LiF as Li-precursor with the uniform flake-like particles and smaller particle size (about 300 nm) exhibits the better performance. At the 50th cycle, the reversible specific capacities for Li₃V₂(PO₄)₃ measured between 3 and 4.8 V at 1C rate are found to approach 147.1 mAh/g (93.8% of initial capacity). The specific capacity of 123.6 mAh/g can even be hold between 3 and 4.8 V at 5C rate.     

Electrochemical behavior of lithium intercalated in a molybdenum disulfide-crown ether nanocomposite

A new nanocomposite, obtained from the intercalation of the cyclic ether 12-Crown-4 into MoS₂, Li_0.32MoS₂(12-Crown-4)_0.19, is described. The laminar product has an interlaminar distance of 14.4 Å. The electrical conductivity of the nanocomposite varies from 2.5 × 10⁻² to 4.3 × 10⁻² S cm⁻¹ in the range 25-77 °C, being about four times higher than the analogous poly(ethylene oxide) (PEO) derivative at room temperature. The electrochemical step-wise galvanostatic intercalation or de-intercalation of lithium, leading to Li_xMoS₂(12-Crown-4)_0.19 with x in the range 0.07-1.0, indicates a Li/Li⁺ pair average potential of 2.8 V. The electrochemical lithium diffusion coefficients in the crown ether intercalates, determined by galvanostatic pulse relaxation between 15 and 37 °C at different lithium intercalation degrees, are higher than those of the PEO derivatives under similar conditions, being however the diffusion mechanism rather more complex. The variation of both, the lithium diffusion activation enthalpy and the quasi-equilibrium potentials, with the lithium content shows there are two different limit behaviors, at low and high lithium intercalation degree, respectively. These features are discussed by considering the high stability of the Li-crown ether complex and the different chemical environments found by lithium along the intercalation process.     

High-rate characteristics of novel anode Li4Ti5O12/polyacene materials for Li-ion secondary batteries

In recent years, spinel lithium titanate (Li₄Ti₅O₁₂) as a superior anode material for energy storage battery has attracted a great deal of attention because of the excellent Li-ion insertion and extraction reversibility. However, the high-rate characteristics of this material should be improved if it is used as an active material in large batteries. One effective way to achieve this is to prepare electrode materials coated with carbon. A Li₄Ti₅O₁₂/polyacene (PAS) composite were first prepared via an in situ carbonization of phenol-formaldehyde (PF) resin route to form carbon-based composite. The SEM showed that the Li₄Ti₅O₁₂ particles in the composite were more rounded and smaller than the pristine one. The PAS was uniformly dispersed between the Li₄Ti₅O₁₂ particles, which improved the electrical contact between the corresponding Li₄Ti₅O₁₂ particles, and hence the electronic conductivity of composite material. The electronic conductivity of Li₄Ti₅O₁₂/PAS composite is 10⁻¹ S cm⁻¹, which is much higher than 10⁻⁹ S cm⁻¹ of the pristine Li₄Ti₅O₁₂. High specific capacity, especially better high-rate performance was achieved with this Li₄Ti₅O₁₂/PAS electrode material. The initial specific capacity of the sample is 144 mAh/g at 3 C, and it is still 126.2 mAh/g after 200 cycles. By increasing the current density, the sample still maintains excellent cycle performance.     

Synthesis and electrochemical properties of Co-doped Li3V2(PO4)3 cathode materials for lithium-ion batteries

Co-doped Li₃V_2−xCo_x(PO₄)₃/C (x = 0.00, 0.03, 0.05, 0.10, 0.13 or 0.15) compounds were prepared via a solid-state reaction. The Rietveld refinement results indicated that single-phase Li₃V_2−xCo_x(PO₄)₃/C (0 ≤ x ≤ 0.15) with a monoclinic structure was obtained. The X-ray photoelectron spectroscopy (XPS) analysis revealed that the cobalt is present in the +2 oxidation state in Li₃V_2−xCo_x(PO₄)₃. XPS studies also revealed that V⁴⁺ and V³⁺ ions were present in the Co²⁺-doped system. The initial specific capacity decreased as the Co-doping content increased, increasing monotonically with Co content for x > 0.10. Differential capacity curves of Li₃V_2−xCo_x(PO₄)₃/C compounds showed that the voltage peaks associated with the extraction of three Li⁺ ions shifted to higher voltages with an increase in Co content, and when the Co²⁺-doping content reached 0.15, the peak positions returned to those of the unsubstituted Li₃V₂(PO₄)₃ phase. For the Li₃V_1.85Co_0.15(PO₄)₃/C compound, the initial capacity was 163.3 mAh/g (109.4% of the initial capacity of the undoped Li₃V₂(PO₄)₃) and 73.4% capacity retention was observed after 50 cycles at a 0.1 C charge/discharge rate. The doping of Co²⁺into V sites should be favorable for the structural stability of Li₃V_2−xCo_x(PO₄)₃/C compounds and so moderate the volume changes (expansion/contraction) seen during the reversible Li⁺ extraction/insertion, thus resulting in the improvement of cell cycling ability.     

Microstructure effect on the electrochemical property of Li4Ti5O12 as an anode material for lithium-ion batteries

Porous (P-) and dense (D-) lithium titanate (Li₄Ti₅O₁₂) powders as an anode material for lithium-ion batteries have been synthesized by spray drying followed by solid-state calcination. Electrochemical testing results showed that the discharge capacities of P-Li₄Ti₅O₁₂ are 144 mAh/g, 128 mAh/g and 73 mAh/g at the discharging rate of 2C, 5C and 20C, respectively (cut-off voltages: 0.5-2.5 V). The corresponding values for D-Li₄Ti₅O₁₂ are 108 mAh/g, 25 mAh/g and 17 mAh/g. The higher capacity of the P-Li₄Ti₅O₁₂ at high charge/discharge rates was attributed to the shorter transport path of Li ions and higher electronic conductivity in the P-Li₄Ti₅O₁₂ as a result of its smaller primary particle size and higher surface area compared with those of the D-Li₄Ti₅O₁₂.     

Characterization of structure and electrochemical properties of lithium manganese oxides for lithium secondary batteries hydrothermally synthesized from δ-KxMnO2

Lithium manganese oxides have attracted much attention as cathode materials for lithium secondary batteries in view of their high capacity and low toxicity. In this study, layered manganese oxide (δ-K_xMnO₂) has been synthesized by thermal decomposition of KMnO₄, and four lithium manganese oxide phases have been synthesized for the first time by mild hydrothermal reactions of this material with different lithium compounds. The lithium manganese oxides were characterized by powder X-ray diffraction (XRD), inductively coupled plasma emission (ICPE) spectroscopy, and chemical redox titration. The four materials obtained are rock salt structure Li₂MnO₃, hollandite (BaMn₈O₁₆) structure α-MnO₂, spinel structure LiMn₂O₄, and birnessite structure Li_xMnO₂. Their electrochemical properties used as cathode material for secondary lithium batteries have been investigated. Of the four lithium manganese oxides, birnessite structure Li_xMnO₂ demonstrated the most stable cycling behavior with high Coulombic efficiency. Its reversible capacity reaches 155 mAh g⁻¹, indicating that it is a viable cathode material for lithium secondary batteries.     

Electrochemical behavior of LiCoO2 in a saturated aqueous Li2SO4 solution

The electrochemical behavior of a commercial LiCoO₂ with spherical shape in a saturated Li₂SO₄ aqueous solution was investigated with cyclic voltammetry and electrochemical impedance spectroscopy. Three redox couples at E_SCE = 0.87/0.71, 0.95/0.90 and 1.06/1.01 V corresponding to those found at ELi/Li⁺=4.08/3.83, 4.13/4.03 and 4.21/4.14 V in organic electrolyte solutions were observed. The diffusion coefficient of lithium ions is 1.649 × 10⁻¹⁰ cm² s⁻¹, close to the value in organic electrolyte solutions. The results indicate that the intercalation and deintercalation behavior of lithium ions in the Li₂SO₄ solution is similar to that in the organic electrolyte solutions. However, due to the higher ionic conductivity of the aqueous solution, current response and reversibility of redox behavior in the aqueous solution are better than in the organic electrolyte solutions, suggesting that the aqueous solution is favorable for high rate capability. The charge transfer resistance, the exchange current and the capacitance of the double layer vary with the charge voltage during the deintercalation process. At the peak of the oxidation (0.87 V), the charge transfer resistance is the lowest. These fundamental results provide a good base for exploring new safe power sources for large scale energy storage.     

Enhanced luminescence of novel Ca3B2O6:Dy phosphors by Li-codoping for LED applications

The Ca_3−xB₂O₆:xDy³⁺ (0.0 ≤ x ≤ 0.105) and Ca_2.95−yDy_0.05B₂O₆:yLi⁺ (0 ≤ y ≤ 0.34) phosphors were synthesized at 1100 °C in air by solid-state reaction route. The as-synthesized phosphors were characterized by X-ray powder diffraction (XRD), scanning electron microscope (SEM), photoluminescence excitation (PLE) and photoluminescence (PL) spectra. The PLE spectra show the excitation peaks from 300 to 400 nm is due to the 4f-4f transitions of Dy³⁺. This mercury-free excitation is useful for solid state lighting and light-emitting diodes (LEDs). The emission of Dy³⁺ ions upon 350 nm excitation is observed at 480 nm (blue) due to the ⁴F_9/2 → ⁶H_15/2 transitions, 575 nm (yellow) due to ⁴F_9/2 → ⁶H_13/2 transitions and a weak 660 nm (red) due to ⁴F_9/2 → ⁶H_11/2 emissions, respectively. The optimal PL intensity of the Ca_3−xB₂O₆:xDy³⁺ phosphors is found to be x = 0.05. Moreover, the PL results from Ca_2.95−yDy_0.05B₂O₆:yLi⁺ phosphors show that Dy³⁺ emissions can be enhanced with the increasing codopant Li⁺ content till y = 0.22. By simulation of white light, the CIE of the investigated phosphors can be tuned by varying the content of Li⁺ ions, and the optimal CIE value (0.300, 0.298) is realized when the content of Li⁺ ions is y = 0.22. All the results imply that the Ca_2.95−yDy_0.05B₂O₆:yLi⁺ phosphors could be potentially used as white LEDs.     

A novel layered Li [Li0.12NizMg0.32−zMn0.56]O2 cathode material for lithium-ion batteries

Layered Li[Li_0.12Ni_zMg_0.32−zMn_0.56]O₂ oxide cathodes containing lithium atoms in the transition metal layers were synthesized and characterized using X-ray diffraction (XRD), galvanostatic cycling, and differential scanning calorimetry (DSC). The Li[Li_0.12Ni_zMg_0.32−zMn_0.56]O₂ cathodes deliver a specific discharge capacity of about 190 mAh/g at room temperature and 236 mAh/g at 55 °C when cycled between 2.7 and 4.6 V versus Li/Li⁺. Excellent capacity retention and smooth potential profiles at room and elevated temperatures over extended cycles suggest that this material does not convert into a spinel structure.     

Electrochemical lithium insertion into anatase-type TiO2: An in situ Raman microscopy investigation

Anatase type TiO₂ has been previously largely reported as a candidate negative electrode material for lithium-ion batteries. We report here for the first time the complete in situ Raman study of lithium insertion and de-insertion into three variously nano-sized TiO₂ anatase powders (Prolabo, ca. 80 nm, AK1, ca. 15 nm and MTi5 ca. 8 nm), of which AK1 and MTi5 show superior capacity and cyclability. From these measurements realized in a galvanostatic mode between 3 and 1 V versus Li/Li⁺, the phase transition from a tetragonal to an orthorhombic structure was clearly observed to take place at different quantities of x in Li_xTiO₂. These results confirm the extension of the solid solution domain as particle size is reduced. For the smaller TiO₂ nano-sized materials (AK1 and MTi5), a more pronounced decrease in band intensity when x > 0.3 for Li_xTiO₂, was observed and may be related to the decrease in the optical skin depth linked to the conductivity increase as lithiation proceeds.     

Li6V10O28, a novel cathode material for Li-ion battery

A novel cathode material, lithium decavanadate Li₆V₁₀O₂₈ with a large tunnel within the framework structure for lithium ion battery has been prepared by hydrothermal synthesis and annealing dehydration treatment. The structure and electrochemical properties of the sample have been investigated. The novel material shows good reversibility for Li⁺ insertion/extraction and long cycle life. High discharge capacity (132 mAh/g) is obtained at 0.2 mA/cm² discharge current and potential range between 2.0 and 4.2 V versus Li⁺/Li. AC impedance of the Li/Li₆V₁₀O₂₈ cell reveals that the cathode process is controlled mainly by Li⁺ diffusion in the active material. The novel material would be a promising cathode material for Li-ion batteries.     

Preparation and electrical conductivity of polyethers/WS2 layered nanocomposites

Utilizing the solvothermal synthesis technique, lithium intercalated tungsten disulfide Li_xWS₂ with x > 1 was obtained, which was allowed to react with water to the formation of single-molecule-layer suspension of tungsten disulfide. The layered nanocomposites PEG, PEO/WS₂, intercalating poly(ethylene glycol) (PEG, MW ≈ 1 × 10³, 6 × 10³, 1 × 10⁴) and poly(ethylene oxide) (PEO, MW ≈ 3 × 10⁵) into the tungsten disulfide host galleries, were prepared using the improved exfoliation-adsorption technique. It was revealed that the intercalated polymers within the host galleries are in a double-layer arrangement with an interlayer expansion of about 9 Å. Despite high conductivity of the host material, those of the PEG, PEO/WS₂ nanocomposites were found to be high in the order of 1 × 10⁻² to 10⁻³ S cm⁻¹ at ambient temperature, resulted from the guest-host charge transfers.