Flow and Heat Transfer Characteristics of Two‐Phase Fluid in Inclined Pipes on a Rotation Platform

A rotating platform was used to create dynamic load, and the mixture air–water two‐phase flow and boiling steam–water two‐phase flow were obtained in an inclined test pipe. By changing the parameters, such as inclination of the test pipe, rotational speed, inlet temperature, flow rate, and so on, the experiments for two‐phase flow in the pipe at inclination of 0°, 45°, and 66° were conducted, respectively. The effects of acceleration and inclination on their flow and heat transfer characteristics were investigated. The two‐phase flow patterns in inclined pipes under rotation conditions were caught with a video camera. The images show that the impact mixed flow and churn flow were found in this research. The results show that the acceleration and pipe inclination significantly influence the flow characteristic and heat transfer of the two‐phase pipe flow. As the directions of the dynamic load and the gravity are opposite to the flow direction, the greater the dynamic load and inclination, the higher the pressure drop and the heat emission, and the lower the flow rate, the void fraction, and the fluid temperature. Therefore, the dynamic load and gravity will improve the flow resistance, enhance heat emission and reduce the heat gained by the fluid.     

Experimental study of pool boiling heat transfer of water‐based magnetic fluid on a horizontal heater

The effect of mass concentration of magnetic particles and an applied magnetic field on pool boiling heat transfer of water‐based magnetic fluid on a horizontal heater was investigated. The experimental results show that high‐concentration magnetic fluid deteriorates boiling heat transfer, while middle‐ and low‐concentration magnetic fluid enhances the boiling heat transfer. There was an optimum concentration in which the enhancement of boiling heat transfer was the best. Conclusions were the same with an applied magnetic field that enhances the boiling heat transfer of magnetic fluid further. © 2005 Wiley Periodicals, Inc. Heat Trans Asian Res, 34(3): 180–187, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20054     

Heat transfer characteristics of liquid–solid circulating fluidized beds

An experiment was conducted to obtain heat transfer data in liquid–solid circulating fluidized beds. In the experiment, two kinds of risers were provided, their inner diameter being 24 mm and 12 mm, respectively. Tested particles were of glass and ceramics, having a diameter range from 2.10 to 4.95 mm. Water at ambient conditions was used as the fluidizing liquid. The experimental data showed a trend where the heat transfer coefficient increases gradually with increasing liquid velocity approaching that for a liquid single‐phase flow (“heat transfer enhanced region”), and finally coincides with that for a liquid single‐phase flow (“liquid single‐phase heat transfer region”). The heat transfer coefficient in the heat transfer enhanced region was found to be a function of the slip velocity between liquid and particles. Based on the experimental data, a correlation was proposed for predicting the heat transfer coefficient in the entire region from the heat transfer enhanced region to the liquid single‐phase heat transfer region, which could reproduce the experimental data with an accuracy of ±15%. The proposed correlation agreed well with existing data. © 2008 Wiley Periodicals, Inc. Heat Trans Asian Res, 37(3): 127–137, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20200     

Experimental research of boiling heat transfer of smooth and screwed tube

In this paper, based on the analog theory of heat transfer research, we performed an analog experiment on boiling heat transfer in smooth tube and screwed tubes. These are widely used in the high pressure generator of lithium bromide absorption refrigeration. From the experimental research, we obtained a series of results on the boiling heat transfer of a single smooth tube and three screwed tubes. The working condition is near the zone of bubble boiling and the overheat wall temperature ranges from 2–7 °C, with a fluid medium of pure water and salt water solution. These results agreed well with the known results, and are significant for the practical design and application of a high pressure generator of lithium bromide absorption for refrigeration. © 2007 Wiley Periodicals, Inc. Heat Trans Asian Res, 36(2): 74–84, 2007; Published online in Wiley InterScience ( www.interscience. wiley.com ). DOI 10.1002/htj.20145     

A theoretical study of evaporative heat transfer in high‐velocity two‐phase flow of air–water in a small vertical tube

A theoretical study was performed to investigate the evaporative heat transfer of high‐velocity two‐phase flow of air–water in a small vertical tube under both heating conditions of constant wall temperature and constant heat flux. A simplified two‐phase flow boundary layer model was used to evaluate the evaporative heat transfer characteristics of the annular two‐phase flow. The analytical results show that the gravitational force, the gas–liquid surface tension force, and the inertial force are much smaller than the frictional force and hence can be neglected for a small tube. The evaporative heat transfer characteristics of the small tube with constant wall temperature are quite close to those of the small tube with constant heat flux. The mechanism of the heat transfer enhancement is the forced convective evaporation on the surface of the thin liquid film. © 2003 Wiley Periodicals, Inc. Heat Trans Asian Res, 32(5): 430–444, 2003; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.10110     

Experimental study of the flow boiling heat transfer enhancement and pressure drop due to the bubble behavior restricted by a screen sheet

A unique method previously proposed by the authors was applied to the heat transfer augmentation in the flow boiling field. In this method a screen sheet was placed on the horizontal heated surface where bubble nucleation occurred. Generated vapor bubbles were trapped between the screen and the wall, became flat, and moved along the surface. This restricted bubble behavior caused the heat transfer enhancement. Three types of screen sheet were tested in the present experiment and the effect of the screen on the heat transfer and two‐phase flow characteristics was investigated. In two of these cases, the screen was displaced upward by the bubble nucleation. Compared with the ordinary flow boiling case, heat transfer was enhanced by a factor of 1.2 to 6 within the present experimental range. Using a simple flow model, it was made clear that the effect of the height of the displaced screen was important in evaluating the increase in pressure drop. © 2003 Wiley Periodicals, Inc. Heat Trans Asian Res, 32(4): 319–329, 2003; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.10094     

Film boiling heat transfer around a vertical finite‐length cylinder with a convex hemispherical bottom

The film boiling heat transfer around a vertical silver cylinder with a convex hemispherical bottom was investigated experimentally in quiescent water at atmospheric pressure. The experiments have been carried out using a quenching method. The diameter and length of the test cylinder are 32 mm and 48 mm, respectively. The test cylinder was heated to about 600 °C in an electric furnace and then cooled in saturated or subcooled water with an immersion depth of about 100 mm. The degree of liquid subcooling was varied from 0 K to 30 K. The analytical solutions for saturated and subcooled boiling are obtained by applying a two‐phase boundary layer theory for vapor film with a smooth interface. The experimental data correlates within ±15% based on the proposed prediction method. Also, the lower limit of film boiling was examined in terms of wall heat flux and degree of superheating. © 2010 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20289     

Experimental studies of rotating heat pipes

Thermal characteristics of a rotating heat pipe were measured under steady state at moderate rotational speeds. Copper‐water rotating heat pipe with copper screen mesh wick was fabricated for testing at various heat loads. An experimental test rig with a water‐cooled condenser section was fabricated to study the heat transfer in the rotating heat pipe (RHP) for various heat loads and various rotational speeds ranging from 1000 rpm to 2000 rpm. A heat transfer correlation was developed for the condensing heat transfer coefficient and compared with the experimental results. © 2009 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20265     

Thermal Performance of a Phase Change Material‐Based Latent Heat Thermal Storage Unit

An experimental analysis is presented to establish the thermal performance of a latent heat thermal storage (LHTS) unit. Paraffin is used as the phase change material (PCM) on the shell side of the shell and tube‐type LHTS unit while water is used as the heat transfer fluid (HTF) flowing through the inner tube. The fluid inlet temperature and the mass flow rate of HTF are varied and the temperature distribution of paraffin in the shell side is measured along the radial and axial direction during melting and solidification process. The total melting time is established for different mass flow rates and fluid inlet temperature of HTF. The motion of the solid–liquid interface of the PCM with time along axial and radial direction of the test unit is critically evaluated. The experimental results indicate that the melting front moves from top to bottom along the axial direction while the solidification front moves only in the radial direction. The total melting time of PCM increases as the mass flow rate and inlet temperature of HTF decreases. A correlation is proposed for the dimensionless melting time in terms of Reynolds number and Stefan number of HTF. © 2013 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley Online Library ( wileyonlinelibrary.com/journal/htj ). DOI 10.1002/htj.21120     

Lattice Boltzmann simulation of mixed convection heat transfer in a corrugated wall cavity utilizing water‐based nanofluids

In the present study, the effects of Cu and CuO nanoparticles' presence on mixed convection heat transfer in a lid‐driven cavity with a corrugated wall are investigated using the lattice Boltzmann method. The boundary fitting method with second‐order accuracy at both velocity and temperature fields is used to simulate the curved boundaries in the LBM. The problem is investigated for different Richardson numbers (0.1–10), volume fractions of nanoparticles (0–0.05), curve amplitudes (0.05–0.25), and phase shifts of corrugated wall (0–270) when the Reynolds number is equal to 25. The volume fraction of added nanoparticles to the water‐based fluid is less than 0.05 to make dilute suspensions. Results show that adding nanoparticles enhances the rate of heat transfer. It is found that nanoparticles have significant effects on both fluid flow and heat transfer of the mixed convection, especially for low Richardson numbers. A comparison between Cu and CuO nanoparticles shows the Cu nanoparticles have a better effect on heat transfer enhancement for all tested conditions. The results also represent the effective role of a corrugated wall on the rate of nanofluid heat transfer. It is observed that increasing the wavy wall's amplitude leads to a decrease of the average Nusselt numberfor a high Richardson number. © 2012 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley Online Library ( wileyonlinelibrary.com/journal/htj ). DOI 10.1002/htj.21024     

Micro‐bubble emission boiling from horizontal and vertical surfaces to subcooled parallel flow water

Heat removal of more than 10 MW/m² in heat flux has been required in high‐heat‐generation equipment in nuclear fusion reactors. In some conditions of water subcooling and velocity, there appears an extraordinary high heat flux boiling in the transition boiling region. This boiling regime is called micro‐bubble emission boiling (MEB) because many micro‐bubbles are spouted from the heat transfer surface accompanying a huge sound. The study intent is to obtain heat transfer performance of MEB in horizontal and vertical heated surfaces to parallel flow of subcooled water, comparing with CHF of this system. Three types of MEB with different heat transfer performance and bubble behavior are observed according to the flow velocity and liquid subcooling. © 2003 Wiley Periodicals, Inc. Heat Trans Asian Res, 32(2): 130–140, 2003; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.10077     

Slug flow heat transfer in a semi‐infinite microtube with temperature jump wall condition

This paper presents an analytical solution of steady‐state heat transfer for laminar, two‐dimensional, and rarefied gas flow in a semi‐infinite microtube. To account for the slip‐flow characteristics of microscale heat transfer, temperature jump condition at the wall has been included in the model while the fluid velocity is assumed to be constant (slug flow). The solution yields closed form expressions for fully‐developed Nusselt numbers in terms of Knudsen number and Prandtl number under both isothermal and isoflux wall conditions. © 2009 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20263     

Hydrothermal Behavior of a Ferrofluid in a Corrugated Channel in the Presence of a Magnetic Field

In this paper, results of applying a non‐uniform magnetic field on a dilute ferrofluid (water and 3% vol. Fe₃O₄) flow in a corrugated channel under a constant heat flux boundary condition have been reported. The thermal behavior of the flow is investigated numerically using a two‐phase mixture model and control volume technique. It is concluded that using a magnetic field with a negative gradient on a nanofluid flow in corrugated channels can be proposed as a suitable method to achieve higher heat transfer performance and augment the heat transfer coefficient and also reduces the wall temperature. This method can lead to the design of more compact heat exchangers. © 2013 Wiley Periodicals, Inc. Heat Trans Asian Res, 43(1): 80–92, 2014; Published online in Wiley Online Library ( wileyonlinelibrary.com/journal/htj ). DOI 10.1002/htj.21060     

Behavioral study of alumina nanoparticles in pool boiling heat transfer on a vertical surface

Experiments were carried out to investigate the pool boiling of alumina‐water nanofluid at 0.1 g/l to 0.5 g/l of distilled water, and the nucleate pool boiling heat transfer of pure water and nanofluid at different mass concentrations were compared at and above the atmospheric pressure. At atmospheric pressure, different concentrations of nanofluids display different degrees of deterioration in boiling heat transfer. The effect of pressure and concentration of nanoparticles revealed significant enhancement in heat flux and deterioration in pool boiling. The heat transfer coefficient of 0.5 g/l alumina‐water nanofluid was compared with pure water and clearly indicates deterioration. At all pressures the heat transfer coefficients of the nanofluid were lower than those of pure water. Experimental observation revealed particles coating over the heater surface and subsequent SEM inspection of the heater surface showed nanoparticles coating on the surface forming a porous layer. To substantiate the nanoparticle deposition and its effect on heat flux, investigation was done by measuring the surface roughness of the heater surface before and after the experiment. While SEM images of the heater surface revealed nanoparticle deposition, surface roughness of the heater surface confirmed it. Based on the experimental investigations it can be concluded that an optimum thickness of nanoparticles coating favors an increase in heat flux. Higher surface temperature due to the presence of nanoparticles coating results in the deterioration of boiling heat transfer. © 2011 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley Online Library ( wileyonlinelibrary.com/journal/htj ). DOI 10.1002/htj.20365     

Characteristics of heat transfer inside a tube during sodium‐water reaction in a FBR steam generator

Sodium reacts chemically with water in the case of an unexpected tube failure of a steam generator (SG) in a fast breeder reactor (FBR). In order to predict the event with high accuracy, it is very important to understand the characteristics of heat transfer inside the tube in detail during the tube failure due to the sodium–water reaction. Experiments were performed by using purified water under the following conditions: initial pressure of 11.2–13.4 MPa, initial water temperature of 200 °C, and water mass flux of 45.7 to 3630 kg/(m²s). The test tube was heated rapidly by high‐frequency induction current. The time averaged heat flux was estimated by using an inverse solution from the measured temperatures at two points on three different locations along the tube. It was confirmed that the derived values agreed with the measured heat fluxes on the outer surface within 20% accuracy. It was found that the characteristics of the heat transfer strongly depend on the flow rate. The heat transfer on the wall changed from nucleate boiling to transient‐film boiling during increasing the heat flux and returned to the nucleate boiling during decreasing the heat flux. A counterclockwise cycle always appeared in the transition boiling region, where the nucleate and film boiling coexisted and the area ratio of these varied with time. The adequacy of heat transfer correlations to evaluate tube overheating was confirmed. © 2010 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/htj.20320     

The heat transfer heterogeneities of bends in flow boiling of hairpin tubes

A series of visual experiments were conducted for liquid– vapor two‐phase flow in hairpin tubes, and it was observed that most of the nucleation sites were located at the outer tube wall of the bend. From the simulation, it was concluded that the uneven velocity distribution in the bend induced the heat transfer heterogeneity. Furthermore, the nucleation of both the inner and outer tube wall of the bend and the wall temperature distribution were discussed to understand the physical phenomena. © 2009 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20269     

Heat transfer for flow boiling of water and critical heat flux in a half‐heated round tube under low‐pressure conditions

Heat transfer for flow boiling of water and critical heat flux (CHF) experiments in a half‐circumferentially heated round tube under low‐pressure conditions were carried out. To clarify the flow patterns in the heated section, experiments in the round tube under the same conditions were also carried out, and their results were compared. The experiments were conducted with atmospheric‐pressure water in test sections with inner diameter D = 6 mm, heated length L = 360 mm, inlet water subcooling ΔT_in = 80 K, and mass velocity G from 0 to 2000 kg/(m²·s) for the half‐circumferentially heated round tube and from 0 to 7000 kg/(m²·s) for the full‐circumferentially heated tube. The experimental data demonstrated that the wall temperature near the outlet of the half‐circumferentially heated tube remained almost the same until CHF. It was found that burnout occurred when the flow regime changed from churn flow to annular flow, and the liquid film on the heated wall dried out although liquid film on the unheated wall remained. © 2002 Wiley Periodicals, Inc. Heat Trans Asian Res, 31(3): 149–164, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.10022     

Free Convective Flow in an Open‐Ended Vertical Porous Wavy Channel with a Perfectly Conductive Thin Baffle

The problem of steady two‐dimensional free convective flow of a Walters fluid (model B ′) in a porous medium between a long vertical wavy wall and parallel flat wall in the presence of a heat source is discussed. The channel is divided into two passages by means of a thin, perfectly conductive plane baffle and each stream will have its own pressure gradient and hence the velocity will be individual in each stream. The governing equations of the fluid and the heat transfer have been solved subject to the relevant boundary conditions by assuming that the solution consists of two parts: a mean part and disturbance or perturbed part. Exact solutions are obtained for the mean part and the perturbed part is solved using long wave approximation. Results are presented graphically for the distribution of velocity and temperature fields for varying physical parameters such as Grashof number, wall temperature ratio, porous parameter, heat source/sink parameter, product of non‐dimensional wave number, and space‐coordinate and viscoelastic parameter at different positions of the baffle. The relevant flow and heat transfer characteristics, namely, skin friction and the rate of heat transfer at both walls, has been discussed in detail. © 2013 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley Online Library ( wileyonlinelibrary.com/journal/htj ). DOI 10.1002/htj.21118     

Heat transfer characteristics in a condenser of closed two‐phase thermosyphon: Effect of entrainment on heat transfer deterioration

Condensation heat transfer in a closed two‐phase thermosyphon is experimentally examined using two different types of test section. Test Section 1 is a straight‐pipe‐type thermosyphon, whereas Test Section 2 has a large‐diameter evaporator compared with a condenser to minimize entrainment at the evaporator. Condensation heat transfer in Test Section 1 shows much lower heat transfer coefficients than those estimated by a Nusselt theory. This low condensation heat transfer occurs due to a working fluid entrainment. It is confirmed from a result of Test Section 2 that the condensation heat transfer is similar to the values predicted by the Nusselt theory as far as the effect of the working fluid entrainment is negligible and flooding does not occur. A new correlation for the heat transfer coefficient considering the effect of entrainment is proposed. © 2002 Wiley Periodicals, Inc. Heat Trans Asian Res, 31(3): 212–225, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.10030     

Mixed convective heat transfer of water in a pipe under supercritical pressure

Because of the rapid properties variation of fluid under supercritical pressure, there is a violent secondary flow in a heated pipe, which will certainly complicate the heat transfer of fluid in a pipe under supercritical pressure. In this paper, a numerical study is conducted for the laminar developing mixed convective heat transfer of water under supercritical pressure. The velocity field and temperature field are given, and the influence of different parameters on flow and heat transfer is investigated in detail. The results show that secondary flow has a great influence on velocity and temperature distributions and thus affects the friction factor and the Nusselt number remarkably. © 2005 Wiley Periodicals, Inc. Heat Trans Asian Res, 34(8): 608–619, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20079