Effects of natural weathering on the fire properties of intumescent fire‐retardant coatings

Fire‐retardant coatings could be one option for providing enhanced protection to buildings during a wildfire, particularly when applied to combustible siding and in under‐eave areas. Limited studies have been conducted on their effectiveness but maintaining adequate performance after weathering has been questioned. This paper reports on a study evaluating the effect of natural weathering on the performance of intumescent‐type fire‐retardant coatings. The main concerns were (a) the reduction of ignition resistance of the coating after weathering and (b) the coating might contribute as a combustible fuel and assist the fire growth after weathering. This study evaluated the performance of 3 intumescent coatings that were exposed to natural weathering conditions for up to 12 months. A bench‐scale evaluation using a cone calorimeter was used to evaluate the performance of the coatings at 3 heat flux levels (30, 50, and 70 kW/m²). Our results showed that weathering exposure reduced the effectiveness of fire protection of intumescent coatings, but the weathered coatings did not act as additional fuels. Weathering orientation showed much less effect on the performance of intumescent coatings in comparison to other parameters. There was statistical evidence that weathering duration, heat flux level, and coating type affected the combustion properties.     

Reduced‐scale test to assess the effect of fire barriers on the flaming combustion of cored composites: An upholstery‐material case study

Herein, we describe a reduced‐scale test (“Cube” test), measuring the fire performance of specimens including a fire barrier (FB) and a flammable core material, which acts as the main fuel load. The specimen is intended to reproduce a cross‐section of a composite product where heat/mass transfer occurs primarily in a direction perpendicular to the FB. The Cube test procedure and benefits are discussed in this work by adopting residential upholstery furniture as an exemplary study. One flexible polyurethane foam, one polypropylene cover fabric, and 10 commercially available FBs were selected. They were used to compare the fire performance of FBs, measured in terms of peak of heat release rate, in the ASTM E1474‐14 standard test and the newly developed Cube test. Edge effects severely affected the performance of FBs in the ASTM E1474‐14 standard test but not in the Cube test. Furthermore, appropriate test conditions were determined in the Cube test to measure the so‐called “wetting point,” that is, the time and value of heat release rate measured when flammable liquid products were first observed on the bottom of the specimen. The relevance of the “wetting point” in terms of full‐scale fire performance and failure mechanism of FBs is discussed.     

Apparatus for the vertical orientation cone calorimeter testing of flexible polyurethane foams

Of concern to regulators and fire safety engineers is how flexible polyurethane foam drips and flows during burning. Specifically, flexible polyurethane foam forms a burning ‘pool’ of liquid as the foam decomposes, which can lead to accelerated flashover events. To fully study this phenomenon where the ‘pool fire’ accelerates heat release, large‐scale tests like the furniture calorimeter (American Society of Testing and Materials (ASTM) E1537) are used, and no small‐scale technique exists. In this paper, we present our work in developing a new sample holder that works with a bench‐scale heat release test, the cone calorimeter (ASTM E1354). The holder was built upon designs developed by the National Institute of Standards and Technology, which placed the foam in a cage in a vertical orientation during cone calorimeter testing. In this paper, we show the schematics for this test apparatus, as well as results obtained with this apparatus on four different flexible foams (shape memory and high‐density foam, flame retarded and non‐flame retarded). We compare the results from the vertical testing with that obtained via traditional horizontal ASTM E1354 testing. The advantages and disadvantages of this new apparatus are discussed in this paper. Copyright © 2014 John Wiley & Sons, Ltd.     

A simplified model for predicting the ignition of FRP composites with validation using intermediate‐scale fire experiment data

This study presents a simplified theoretical model to predict the ignition of FRP composites of general thermal thickness (GTT) subjected to one‐sided heating. A simplified GTT heat transfer model to predict the surface temperature of GTT composite panels was developed, and the exposed surface temperature was used as ignition criterion. To validate the GTT model, intermediate scale calorimeter fire tests of E‐glass fiber reinforced polyester composite panels at three heat flux levels were performed to obtain intermediate‐scale fire testing data in a controlled condition with well‐defined thermal boundary conditions. The GTT model was also verified by using results from finite element modeling predictions. This model can be used to estimate the surface temperature increase, time‐to‐ignition, and mass loss of FRP composites for fire safety design and analysis. Copyright © 2013 John Wiley & Sons, Ltd.     

Mechanical properties of fire‐damaged glass‐reinforced phenolic composites

Changes to the mechanical and physical properties of a glass‐reinforced resole phenolic composite due to intense radiant heat and fire are investigated. Fire testing was performed using a cone calorimeter, with the composite exposed to incident heat fluxes of 25, 50, 75 or 100 kW/m² for 325 s and to a constant flux of 50 kW/m² for different times up to 1800 s. The post‐fire tensile and flexural properties were determined at room temperature, and these decreased rapidly with increasing heat flux and heat exposure time due mainly to the chemical degradation of the phenolic resin matrix. The intense radiant heat did not cause any physical damage to the composite until burning began on exposure to a high heat flux. The damage consisted of cracking and combustion of the phenolic matrix at the heat‐exposed surface, but this only caused a small reduction to the mechanical properties. The implication of the findings for the use of glass‐reinforced resole phenolic composites in load‐bearing structures for marine craft and naval ships, where fire is a potential hazard, is discussed. Copyright © 2000 John Wiley & Sons, Ltd.     

Test method for concrete spalling using small electric furnace

Concrete spalling can cause severe damage to concrete structure when exposed to fire. The spalling mechanisms are not very well understood. For the testing of spalling, full‐scale structural members should be used, as spalling tests are sensitive to size effects. Full‐scale testing in large furnace is costly and is not suitable for testing large number of concrete mixture trials. The standard and hydrocarbon fire time–temperature curves have rapid temperature rise during the initial phase. This temperature rise requires a gas furnace with high heating capacity and cannot be generated by electric muffle furnace commonly available in many laboratories. This paper presents a method to carry out spalling test in small‐scale specimens with exposure to rapid temperature rise using a commonly available electric furnace in the laboratories. The tests are based on 150 mm diameter cylinders that are laterally confined to simulate full‐scale structural members. The cylinder surface is exposed to rapid temperature rise by exposing through vertical and/or horizontal holes in pre‐heated small electric furnace. Some unconfined 100 mm diameter cylinders were also exposed horizontally to test the performance of confinement. The paper shows that the hydrocarbon fire and standard fire exposure can be simulated by manipulating the exposure location of the surface of the concrete cylinder. Ordinary Portland cement concrete cylinders with different strengths were tested and different spalling patterns were observed. The spalling patterns matched the test results from a gas furnace fire test simulating the fire curves. The tests demonstrated that the method is an effective and convenient technique to predict the spalling risk of a concrete. Copyright © 2009 John Wiley & Sons, Ltd.     

A model to predict fire resistance of non‐load bearing wood‐stud walls

The author has developed a series of computer models to predict the fire resistance of wood‐framed walls and floors. The models utilize two‐dimensional heat‐conduction equations and thermo‐physical property data to describe heat transfer through the assemblies. The model for wall assemblies WALL2D, the basic version of the wall model, has already been published in Fire and Materials. Recently, WALL2D has been extended to WALL2DN to analyse heat transfer through insulated walls and walls that experience openings at the joints between adjacent sheets of gypsum board. Since gypsum board shrinks at high temperatures, the joints between adjacent sheets of gypsum board open. Hot fire gases, thereby, enter the openings and heat the edge of the gypsum board and wood studs. The new model WALL2DN simulates the joint opening and describes the resultant effect of openings. The model also calculates heat transfer through insulation in the stud cavity and depicts the effect of insulation on the fire resistance of non‐load bearing wall assemblies. Insulation selected in WALL2DN is glass‐fibre insulation, rock‐fibre insulation, polystyrene foam and polyurethane foam. When walls are exposed to fire, the insulation in the cavity shrinks (and/or melts) and an empty space appears at the interface between insulation and gypsum board. The model simulates this shrinking behaviour of insulation in the cavity. Finally, the model was validated by comparing the predicted results to those from full‐scale standard fire‐endurance tests. Copyright © 2003 John Wiley & Sons, Ltd.     

Incident heat flux measurements in floor and wall furnaces of different sizes

This paper presents the results of incident heat flux experiments in standard (full‐scale) and non‐standard (intermediate‐scale) wall and floor fire resistance furnaces. These experiments were conducted to investigate the effects of full‐scale furnace depth (wall and floor furnaces), furnace size (full‐ and intermediate‐scale furnaces) and intermediate‐scale furnace orientation (vertical and horizontal positions) on the incident heat flux in fire resistance test furnaces. Copyright © 2005 Crown in the right of Canada. Published by John Wiley & Sons, Ltd.     

Poly(vinyl chloride) and its fire properties

This work provides an up‐to‐date review of the fire properties of poly(vinyl chloride) (PVC) materials, both rigid (unplasticized) and flexible (plasticized). The fire properties addressed include ignitability, ease of extinction (oxygen index), flame spread (small scale and intermediate scale), heat release, smoke obscuration, smoke toxicity, hydrogen chloride emission and decay, and performance in real‐scale fires. This comprehensive review includes a wide selection of references and tables illustrating the properties of PVC materials in comparison with those of other polymeric materials, including, in many instances, wood materials. The work puts these fire properties in perspective, showing that the heat release rate (the key fire property) of rigid PVC (and that of properly flame‐retarded flexible PVC) are among the lower values found for combustible materials. This work also shows that the smoke toxicity and smoke obscuration resulting from burning PVC materials in real‐scale fires is in the same range as those of other materials.     

Performance of a non‐load‐bearing steel stud gypsum board wall assembly: Experiments and modelling

A gypsum wall assembly was exposed to an intense real‐scale compartment fire. For the wall assembly, temperatures were measured at the exposed face, within the stud cavity, and at the unexposed face during the fire exposure. Total heat flux gauges were used to measure the temporal variation of the energy incident on the walls, and cameras, both visual and infrared, were used to image the unexposed face of the wall assembly during the fire exposure. The behaviour of the wall assembly under the fire load is discussed as are current model results for a simulation of the fire test. Copyright © 2006 John Wiley & Sons, Ltd.     

Investigation of a combustible material in the fire of Hengyang merchant's building

Agaric, a kind of important combustible material in the fire of Hengyang merchant's building, was investigated using different experiment equipments. Its degradation and pyrolysis behavior were studied by means of thermogravimetric and kinetic analysis and pyrolysis gas chromatography–mass spectroscopy analysis. External radiation heat and internal heat were used to ignite the agaric. For external radiation ignition, a series of bench‐scale fire tests were done in cone calorimeter in accordance with ISO 5660. As for the internal heat ignition, a fire test was carried out in a full‐scale room in accordance with ISO 9705. Multi‐parameter measurement, including heat release rate (HRR), mass loss rate (MLR), temperature field and species concentration, has been accomplished. Meanwhile, the process of a full‐scale fire test was numerically simulated. The computational results were consistent with experiment data, which will lay down a good foundation for further study in fire reconstruction of the whole fire. Copyright © 2008 John Wiley & Sons, Ltd.     

Effects of variations in incident heat flux when using cone calorimeter test data for prediction of full‐scale heat release rates of polyurethane foam

The development of methods to predict full‐scale fire behaviour using small‐scale test data is of great interest to the fire community. This study evaluated the ability of one model, originally developed during the European Combustion Behaviour of Upholstered Furniture (CBUF) project, to predict heat release rates. Polyurethane foam specimens were tested in the furniture calorimeter using both centre and edge ignition locations. Input data were obtained using cone calorimeter tests and infrared video‐based flame area measurements. Two particular issues were investigated: how variations in incident heat flux in cone calorimeter tests impact heat release rate predictions, and the ability of the model to predict results for different foam thicknesses. Heat release rate predictions showed good agreement with experimental results, particularly during the growth phase of the fire. The model was more successful in predicting results for edge ignition tests than for centre ignition tests and in predicting results for thinner foams. Results indicated that because of sensitivity of the burning behaviour to foam specimen geometry and ignition location, a single incident heat flux could not be specified for generating input for the CBUF model. Potential methods to determine appropriate cone calorimeter input for various geometries and ignition locations are discussed. Copyright © 2014 John Wiley & Sons, Ltd.     

Role of two stage pyrolysis in fire growth on flexible polyurethane foam slabs

A series of experiments designed to characterize fire behavior on flat 1.2 m × 1.2 m samples of commercial non‐fire‐retarded flexible polyurethane foam were performed. Time‐resolved heat release and mass loss rates were measured. Experimental parameters varied, including foam thickness (5.1 and 10.2 cm) and burning angle (+25°, +12.5°, 0°, ?12.5°, and ?25°). Polyurethane foam is typically produced by reacting a multifunctional isocyanate with a polyol. The foam used here was formed by reacting toluene diisocyanate and a polyol based on a condensed polyether of polypropylene oxide. Earlier cone calorimeter studies of this foam had revealed a clear two stage pyrolysis behavior in which the heated foam first released a gaseous fuel derived from the isocyanate component, while leaving behind a liquid produced primarily from the polyol, which only gasified and burned following additional heating. The subsequent burning behavior of the polyol‐derived liquid is shown in this work to play a crucial role in the maximum heat release rate and total heat released by the fires spreading across the foam slabs. Published 2013. This article is a U.S. Government work and is in the public domain in the USA.     

Inorganic polymeric materials for passive fire protection of underground constructions

Protection against fire for reinforced concrete constructions is of great importance worldwide. There is a general perception that concrete structures are incombustible and thus, they have good fire‐resistance properties. In a real fire incident, however, concrete can be subjected to excess temperatures causing severe spalling and serious damage to concrete structures with significant economic cost and high potential risk to human life safety. Although a variety of fire‐protection methods exist, there is always a need for the development of new materials with improved thermophysical properties and low cost. Inorganic polymeric materials are promising from this point of view. They are incombustible, combining excellent physical, chemical, mechanical and thermal properties with low production cost and significant environmental benefits. In this work, the thermophysical properties of ferronickel slag‐based inorganic polymeric materials are studied. The results from the laboratory scale experiments are promising and indicative of the large‐scale behavior of material. The effectiveness of this material has to be proved in large‐scale experiments at higher temperatures simulating several severe fire scenarios as well as under all kinds of mechanical loading before concluding for its applicability as a fire protection system. Copyright © 2012 John Wiley & Sons, Ltd.     

Investigation of polymeric materials using the cone calorimeter

The use of polymeric materials in building or construction applications is steadily increasing. Therefore, the potential for these materials to be exposed to fire is also increased. The understanding of the pyrolysis characteristics of these materials is thus a necessity. There are many standard tests used to evaluate materials. Unfortunately, the correlation between these tests and large scale fire is less than desirable. A new bench scale rate of heat release apparatus, the Cone Calorimeter, is now being used more frequently in pyrolysis testing of polymeric materials. This apparatus has been shown to correlate much better between room scale testing and large scale fire testing. The cone Calorimeter provides a pyrolysis profile of a material under ambient oxygen conditions. Characteristics such as ignition time, total heat release, maximum rate of heat release, mass loss during pyrolysis, CO₂, CO, and smoke production are determined. In this work several almost neat polymers are examined and the general pyrolysis characteristics of these polymers are discussed. The objective of this work is to provide information of basic polymeric pyrolysis properties of these materials. Variations in the material, i.e., molecular weight, polydispersity, and residual catalysis, along with changes in testing procedures, can have dramatic effects on results. Obviously the addition of flame retardant and flame retardant packages to any of these materials will have dramatic effects on results.     

Comparison of simulated wet bench fires with small‐ and intermediate‐scale fire tests

Fire hazard studies of clean room facilities indicated that significant losses due to fire may occur in the semiconductor industry. The present study reports the results of full‐scale wet bench fire tests conducted (1) to assess the fire hazards of existing wet bench materials not meeting the listing requirement of NFPA 318, (2) to assess the impact on wet bench fires of engineered materials with improved flammability characteristics, and (3) to compare the observed fire behavior with the results of simpler small‐ and intermediate‐scale fire tests using the same materials. The full‐scale wet bench fires were observed to be consistent in terms of chemical heat release rate, fire propagation, and smoke generation with the results of the small‐ and intermediate‐scale test results. The simpler fire tests are incorporated in FM Approvals 4910 certification for materials to be used in semiconductor fabrication facilities. The small‐scale test protocol is also standardized in NFPA 287. Copyright © 2008 John Wiley & Sons, Ltd.     

A numerical study of gypsum plasterboard behaviour under standard and natural fire conditions

Gypsum plasterboards are the most widely used passive fire protection for timber structures, especially in the case of light timber frame construction. Understanding the complex thermo‐physical behaviour of plasterboard at elevated temperature is vital in the performance‐based design of any structure adopting gypsum as passive fire protection (PFP). Numerous heat transfer studies have been conducted over the years where attempts have been made to simulate the fire performance of gypsum‐protected assemblies, subject to standard fire exposure. However, contradictory thermal properties for gypsum plasterboard are apparent throughout. As a result, it is unclear from a practitioner's perspective as to which studies represent reasonable properties for design purposes. In recognition of this the authors present a numerical study highlighting the consequences of adopting many of the differing property sets available in the literature, the sensitivity of temperature development resulting from deviations from the assumptions that underpin such properties, and the consequences of adopting plasterboard properties derived from standard fire tests, in natural fire situations. The study presents heat transfer simulations conducted using the finite element software TNO DIANA coupled with both laboratory and natural fire tests conducted on Structural Insulated Panels (SIPs) and Engineered Floor Joists (EFJs). It is found from this study that plasterboard properties are highly sensitive to the assumed free and chemically bound moisture contents. Minor percentage changes are shown to have a significant influence on the temperature development of SIPs exposed to standard furnace fires, while some of the most accepted plasterboard properties available in the literature are found, in some cases, to be non‐conservative when adopted in simulations of SIPs. More interestingly, it is also found that the properties of plasterboard available in the literature, largely derived from standard fire tests, are not independent of the heating rate. As a result, when such properties are applied to natural fire problems significant inaccuracies can occur. Copyright © 2011 John Wiley & Sons, Ltd.     

Revealing the inner secrets of intumescence: Advanced standard time temperature oven (STT Mufu+)—μ‐computed tomography approach

Intumescent coatings have been used for fire protection of steel for decades, but there is still a need for improvement and adaptation. The key parameters of such coatings in a fire scenario are thermal insulation, foaming dynamics, and cohesion. The fire resistance tests, large furnaces applying the standard time temperature (STT) curve, demand coated full‐scale components or intermediate‐scale specimen. The STT Mufu⁺ (standard time temperature muffle furnace⁺) approach is presented. It is a recently developed bench‐scale testing method to analyze the performance of intumescent coatings. The STT Mufu⁺ provides vertical testing of specimens with reduced specimen size according to the STT curve. During the experiment, the foaming process is observed with a high‐temperature endoscope. Characteristics of this technique like reproducibility and resolution are presented and discussed. The STT Mufu⁺ test is highly efficient in comparison to common tests because of the reduced sample size. Its potential is extended to a superior research tool by combining it with advanced residue analysis (μ‐computed tomography and scanning electron microscopy) and mechanical testing. The benefits of this combination are demonstrated by a case study on 4 intumescent coatings. The evaluation of all collected data is used to create performance‐based rankings of the tested coatings.     

Basalt/Polyacrylamide-Ammonium Polyphosphate Hydrogel Composites for Fire-Resistant Materials

Hydrogels containing a large amount of water are widely used as fire-resistant materials. However, when exposed to fire, the organic polymer network of gel will burn in a short time as the contained water evaporates. For that, the fire-retarding ammonium polyphosphate (APP) and woven basalt fibers are introduced in polyacrylamide (PAAm) hydrogels to improve the fire-resistant performance. Thermo-gravimetric tests indicating that the APP can prevent gel from decomposition effectively when the content is larger than 13 wt%. And the APP can form a foam layer on gel surface to protect it from burning. The basalt fibers are capable of absorbing heat and strengthening the gel. With the synergetic of APP and basalt fibers, the resultant basalt/PAAm-APP composite with high mechanical strength exhibits excellent fire-resistant performance. It can sustain the 1300 °C flame for as long as 15 min.     

Absorptivity and its dependence on heat source temperature and degree of thermal breakdown

The spectral absorptivity of 62 products has been measured in the wavelength region of 0.3–20 µm. Effective absorptivity for fire‐induced heat radiation typically lies in the range of 0.75–0.95. It was found that the effective absorptivity varies significantly with the temperature of the heat source. This has implications on the heating of a surface. The effect is more important when the absorptivity is used as input for calculations of ignition temperature and thermal inertia. It was also found that the absorptivity of radiation from fires for products exposed to irradiation in many cases decreased with increased exposure time. This is surprising since, for example, wood that is darkened when exposed to heat obviously has a higher absorptivity in the visual part of the spectrum than fresh non‐darkened wood. The reason that was identified for this is because the absorptivity in the IR drops, and measurement results are given which clearly illustrate this. Copyright © 2010 John Wiley & Sons, Ltd.