Soft furnishing fires: They're still a problem

Home fires in which soft furnishings were first ignited or contributed to fire spread cause a disproportionate share of US home fire deaths. Although the death toll from these fires is much lower than in the 1980s, the rate of death per 1000 reported fires has doubled. Data from the National Fire Incident Reporting System and the National Fire Protection Association's annual Fire Experience Survey were used to create national estimates of these fires and casualties. Including both fires in which upholstered furniture was the item first ignited and contributed most to fire spread, in 2013‐2017, upholstered furniture was involved in an estimated average of 7120 (2%) home fires per year, resulting in an average of 570 (22%) deaths per year. Mattresses or bedding were involved in estimated average of 10 530 (3%) home fires per year, resulting in an average of 370 (14%) deaths annually. In most of these fires and deaths, the item was first ignited. Smoking materials were the leading cause of these fires (20%‐26%) and associated deaths (52%‐54%). Various types of operating equipment and small open flames also play a role. Understanding the causes of these fires is essential to develop new strategies to prevent them.     

油品火灾形势分析

文章根据《中国消防年鉴》对近年油品火灾起数、造成人员伤亡、直接财产损失、起火原因等情况进行分析,揭示油品火灾的特点和规律,分析油品消防安全工作的薄弱环节和重点方向。并对今后如何做好油品消防安全工作提出对策和建议。     

Estimating the impact of the mattress fire safety Standard 16 CFR Part 1633 on bed fire outcomes

Beds are a prevalent combustible in fatal fires in the United States effective 1 July 2007, the US Consumer Product Safety Commission promulgated a standard to severely reduce the heat release rate and the early heat output from mattresses and foundations when ignited by a flaming ignition source. This study estimates the Standard's success over its first decade using fire incidence, US population, and mattress sales data. The technique mitigates the influence of some exogenous factors that might have changed during this decade. The Standard is accomplishing its purpose, preventing approximately 65 fatalities (out of an estimated 95 fatalities in 2002‐2005) from bed fires annually during 2015‐2016, although not all pre‐Standard mattresses had yet been replaced. Compared to residential upholstered furniture fires, which were not affected by the Standard, the numbers of bed fires decreased by 12%, injuries by 34%, and deaths by 82% between 2005‐2006 and 2015‐2016. Per bed fire, injuries decreased by 25% and fatalities decreased by 67%, indicating that the severity of bed fires is being reduced.     

Examining the fire risk in London dwellings using the London Fire Brigade Incident database

Analysis of the Fire Brigade's database of fires in London between 2009 and 2020 provided insight into the level of fire safety in the city and how it varies across different types of dwellings and different levels of protection. Regarding the number of fires, fatalities, and injuries, fire safety in London has significantly improved on average over these years. However, average trends cannot analyze catastrophic fires with multiple fatalities, like at Grenfell Tower in 2017, as these events are too rare to form a suitable sample size. Dwelling fires are the most lethal in London: despite accounting for only 28% of fires, they lead to 87% of fatalities and 83% of injuries. The odds of a dwelling fire becoming fatal in London fell from 1 in 174 in 2009 to 1 in 208 in 2019, a decrease of 16%. The total number of fires has decreased over this period, and the number of fires where an alarm was raised has increased, suggesting that the prevention and detection layers of fire safety have improved, while our analysis suggests that the level of protection from the compartmentation and evacuation layers has remained constant over time. An analysis of the different layers of fire protection suggests that compartmentation was the most impactful layer, with a failure in compartmentation increasing the odds of a fire being fatal by 1.5 to 5 times. Overall, this analysis shows that the fire hazard to Londoners in general is low and the lowest since 2009; however, there is still a threat that should not be understated.     

Solving the soft furnishings fire problem (without incurring collateral damage)

Fires in which soft furnishings (upholstered furniture and beds) were either the first item ignited or were identified as the major item in the fire's growth are the deadliest of residential fires. This Special Issue of Fire and Materials on Furniture Flammability grew from a small session on this subject in Interflam 2019. The issue contains 14 papers that describe the fire problems of soft furnishings, research to better understand their burning behavior, and recent success in and promising approaches to reducing the losses from these fires. This introduction concludes with the author's challenges to the fire safety community for reducing the number and consequences of soft furnishings fires.     

Australian fire statistics

This paper describes in some detail the sources of data on fires occurring in Australia with to their scope and reliability. Particular reference is made to the data published by the Fire Brigades Board of New South Wales for these are the most detailed and comprehensive published in Australia although limited to one State. Data are given on the number of fires, property loss, and deaths and injuries due to fires in Australia and on causes, occupancies, points of origin and extents of fires in New South Wales. Comparisons are made with United Kingdom and United States of America statistics where relevant data are available. In conclusion, some trends which indicate that better data should be available in the future are discussed.     

Reconstruction of Grenfell Tower fire. Part 3—Numerical simulation of the Grenfell Tower disaster: Contribution to the understanding of the fire propagation and behaviour during the vertical fire spread

The dramatic event of the Grenfell Tower (June 2017), involving a combustible façade system, has raised concerns regarding the fire risk that these systems address. Indeed, as façades are complex systems, it is not straightforward to assess which part of the system is involved in the global fire behaviour. Understanding such façade fires is thus very complex as it depends on a combination of various products and system characteristics, including window frames or air gap or cavity barriers. Fire development inside the initial apartment was investigated using an appropriate CFD model with different scenarios for the fire source and ventilation conditions in a previous study. Fire propagation through the window to the external façade and to higher apartments was modelled and validated against visual observations. This paper describes CFD modelling of the complete Grenfell tower facade, and investigates vertical fire spread behaviour over the full height façade from the initial apartment. Contributions from the combustion of all the apartments' furniture, depending on window failure, and architectural details of the refurbished façade are considered in the numerical model. The modelling results are validated by comparison with photographic and video observations of the real fire.     

Furniture and furnishings in the home—some fire statistics

A statistical study of fires in the United Kingdom involving the ignition of furniture and furnishings is presented. This paper examines the data for one year (1970). The analysis shows that in fires starting in furniture and furnishings the chance of a fatality is over twice that in other domestic fires. The majority of furniture fires involve upholstery or bedding and over 90% were started by smokers' materials, electric appliances, space heating or as the result of the activities of children or suspected arsonists. Eighty-five percent of the fatalities were found in the room of origin of the fire. Eighty per cent were overcome by smoke or toxic gases. Sixty percent of the fatalities were either under 5 or over 65 years of age. Monetary values are assigned for damage, casualties and deaths in fire. These costs can be used to assess the value of fire precautions. With the values taken, the total losses in furniture fires in the home amounted to £19 million in 1970. Life loss accounted for the major part of this sum. The expected annual loss per dwelling as a result of the ignition of furniture is thus only about £1, and is only £3 for all dwelling fires. This low figure suggests an approach of either selective spending on those most at risk (the elderly and handicapped) or by government activity through publicity and education.     

Design car fire size based on fire statistics and experimental data

Passenger vehicle fires present a significant fire hazard in enclosed car parks. Accordingly, this hazard is often used as a design fire scenario for the application of fire protection systems. Specific fire protection standards, like NFPA 88A:2019 and NFPA 502:2020 in the United States (US) or BS 7346-7:2013, NBN 21-208-2:2014, VDI 6019-1:2006, NEN 6098:2010 and ITB 493:2015 in Europe, provide varying requirements for car park fire protection. Car parks fire strategies, especially when smoke control systems are used, often make use of performance-based methods, in which fire growth (ie, heat release rate [HRR]) plays a fundamental role. The chosen HRR can influence the specification of car park construction and on smoke control system calculations. This article presents a review of 44 full-scale car fire tests together with Polish and British passenger car fire statistics from the last 8 years. Based on the collected data and the averaged tests, HRR values provided in this article could assist local authorities and stakeholders determine optimal fire safety design criteria for car parks.     

Comparison of simulated wet bench fires with small‐ and intermediate‐scale fire tests

Fire hazard studies of clean room facilities indicated that significant losses due to fire may occur in the semiconductor industry. The present study reports the results of full‐scale wet bench fire tests conducted (1) to assess the fire hazards of existing wet bench materials not meeting the listing requirement of NFPA 318, (2) to assess the impact on wet bench fires of engineered materials with improved flammability characteristics, and (3) to compare the observed fire behavior with the results of simpler small‐ and intermediate‐scale fire tests using the same materials. The full‐scale wet bench fires were observed to be consistent in terms of chemical heat release rate, fire propagation, and smoke generation with the results of the small‐ and intermediate‐scale test results. The simpler fire tests are incorporated in FM Approvals 4910 certification for materials to be used in semiconductor fabrication facilities. The small‐scale test protocol is also standardized in NFPA 287. Copyright © 2008 John Wiley & Sons, Ltd.     

Characterization and thermal degradation of protective layers in high‐rating fire‐resistant glass

Fire‐resistant glass products are considered to have better performance against fire. They are developed to replace conventional glass products. However, the smoke emitted from these products can be potentially harmful during fires and cause injuries or even deaths. Six samples of insulating glass available in the local market were selected. A variety of techniques, including X‐ray photoelectron spectroscopy, Fourier transform infrared spectroscopy (FTIR), thermogravimetric FTIR, pyrolysis–gas chromatography–mass spectrometry and tubular furnace coupled FTIR spectroscopy, were employed. According to the test results, there are two types of protective layers of the fire‐resistant glass. One consists of water, water‐soluble salt and polyamide with possible presence of alcohols, and the other consists of water metal silicates with possible presence of carboxylate and alcohols. Gases emitted from the protective layers heated in air, in argon and in vacuum are similar. Water vapor, carbon dioxide and hydrogen chloride are the main components of the gases emitted. Copyright © 2014 John Wiley & Sons, Ltd.     

Post-collision fires in road vehicles between 2002 and 2015

The loss of human lives and body injuries due to post-crash fires, either by smoke inhalation or due to burn injuries, are unfortunately not uncommon. The literature indicates that fire events related to crashes are still a significant problem. The increased combustible load in newer vehicles is an important factor to be taken into account for the fire safety, as well as their potential to release toxic fumes while burning. Trends indicate that the survivable collision energy will continue to increase, and, at the same time, the probability of post-crash fires rises with the collision energy. This means that the occupants of a vehicle may probably survive a high-energy collision but might sustain severe injuries or death due to a post-collision fire. This work reports a literature and interview study about post-crash fires including statistics on the causes and dynamics of post-crash fires in road vehicles based on the literature, crash and incident reports, as well as on interviews with medicine specialists. Results from this study indicate that fires in vehicles which originated by a collision event are a problem that remains to be solved.     

RSET/ASET,a flawed concept for fire safety assessment

For the evaluation of occupant safety in the case of building fires, the Required Safe Egress Time/Available Safe Egress Time (RSET/ASET) concept has become widespread and is now commonly used in the fire safety engineering profession. It has also become commonly used by smoke detector (smoke alarm) manufacturers in assessing whether a particular detector technology is adequate. It is shown in this paper that the concept is intrinsically flawed and its use promotes the diminishment of fire safety available to building occupants. The concept innately ignores the wide variations in capabilities and physical condition of persons involved in fire. It is based on implicitly assuming that, after a brief period where they assess the situation and mobilize themselves, occupants will proceed to the best exit in a robotic manner. This assumption completely fails to recognize that there are very few fires, especially in residential occupancies, where occupants perished or were seriously injured who had endeavored to exit in this robotic manner. Instead, in the vast majority of fire death and serious injury cases, the occupants did not move in such a manner and their evacuation took longer than anticipated on the basis of robotic movement. There is a wide variety of reasons for this, and these are well known in the profession. The concept also ignores that there can be a wide variation in fire scenarios. The same building and the same fire protection features can be evaluated, but both RSET and ASET can change drastically, depending on the scenario used. The consequence of using the RSET/ASET concept for fire safety engineering or product design purposes is that fire deaths and injuries are permitted to occur, which are preventable. Copyright © 2010 John Wiley & Sons, Ltd.     

The fire safety of TV set enclosure materials,a survey of European statistics

The composition of enclosure materials used in many TV sets sold on the European market has changed significantly since the early 1990s. To determine the potential impact of this change on TV fire safety, a review of European and US TV set fire statistics has been carried out. TV set fires can have internal electrical causes due to faults not apparent at the time of manufacture, simple wear and tear, or a variety of external causes. Recent detailed statistics suggest that about one third of all TV fires are due to external ignition. Available data show that the significant drop in the rate of TV set fires experienced in Europe during the 1980s is not continuing today. In fact, the rate appears to be increasing in some countries, such as the UK and Sweden. The number of TV set fires in Europe is estimated as 100 fires per million TV sets per year due to internal ignition sources, at least an order of magnitude higher than in the USA where the fire safety classifications for TV set enclosure materials has been historically high. TV set fires have a dramatic impact on life and property. To avoid an increase in TV set fires, fire safety requirements should be increased, and public awareness of the importance of fire safety in TVs heightened. Copyright © 2000 John Wiley & Sons, Ltd.     

Validation of the lumped parameter code COCOSYS against large‐scale OECD PRISME 2 fire experiments

Fire safety analysis is a major issue for nuclear power plants (NPPs) in the context of deterministic safety assessments as well as of probabilistic safety analyses. Oil reservoirs and cables represent major fire loads. Therefore, simulations of oil and cable fires are of interest for quantifying the risk of such internal hazards in NPPs. To investigate the applicability of lumped parameter (LP) modelling, validations against fire experiments are required. In this way, results obtained with the LP code COCOSYS for simulations of oil and cable fire experiments conducted in the OECD PRISME 2 Project are presented. The PRISME 2 VSP (vertical smoke propagation) tests involving oil fires in a confined and mechanically ventilated facility were used to assess the ability of the LP code to simulate smoke propagation through a horizontal opening from the fire compartment to a compartment on top of it. As it was already identified in the “International Collaborative Fire Modelling Project (ICFMP),” this type of opening might cause problems in fire simulations, particularly for zone or LP fire models. In these simulations, attention has been paid to the coupling between the fire and the surrounding environment due to the decrease of oxygen concentration. Furthermore, different cable materials have been tested in the PRISME 2 CORE (completing and repeating) test campaign. By simulating the CFS‐3 (cable fire spreading) test with confined underventilated conditions, the applicability of the COCOSYS cable fire model with input parameters deduced from open atmosphere fire tests (CORE‐2) was analysed. Results show that the applicability of a LP fire model to predict the pyrolysis rate is partly limited for both oil and cable fires, in confined environment. However, simulations with prescribed pyrolysis rates show encouraging results in good agreement with the experimental data and underline the capability of the LP code COCOSYS to simulate the interaction between the thermal hydraulics inside compartments and the fire source.     

A new test methodology for studying the response of walls to real fire environments

A new test methodology was developed to investigate the response of walls, partitions, and in-wall systems exposed to real fires. The apparatus includes a 3.5 m long, 2.3 m wide, and 2.3 m high fire compartment within a standard sea container. A wall specimen measuring up to 1.8 m wide, 1.8 m tall, and 0.3 m deep is mounted in a steel frame at one end of the fire compartment. Fire exposures to the wall specimen evolve over time depending on the fuel load and ventilation configuration. Gas temperatures and heat flux were characterized for five different fuel and ventilation configurations. Peak exposures ranged from 30 to 75 kW/m² for about 20 minutes. Five additional tests were conducted using a single fuel and ventilation configuration to assess the repeatability of the test methodology. It was found that a 19.3 minute growth period occurred plateauing at a ceiling temperature of 708°C for 8.4 minutes, on average. Compartment gas temperatures were found to be repeatable, having a sample standard deviation less than 32°C for symmetric data. Repeatability improved when account was taken for the rapid fire growth inflection point. The utility of the approach for studying fire performance of building elements was demonstrated.     

Evaluating the performance of a portable water–mist fire extinguishing system with additives

This study investigates how high‐pressure water–mist system discharge methodologies influence the fire extinction performance for pan pool fires and the corresponding mechanisms of restraining fire. The fire source is a pool‐fire burner. Fine water spray is injected using a portable device. The additive in the water–mist is neither toxic nor corrosive. All the tests are regarded as fuel controlled. The fire test parameters are fuel type, nozzle discharge angle, and additive solution volume. The fuels used are heptane, gasoline, and diesel. Nozzle discharge angles are 30, 45, and 60° with respect to the ground. Additive solution volumes are 0% (pure water), 3, 6, and 10%. Test results indicate that the nozzle discharge angle and additive solution volume in a water–mist fire extinction system play a significant role. Fire extinguishing efficiency is influenced by mist effects and the additive. Furthermore, the water–mist system can reduce radiation and can provide good protection for operators using portable fire extinguishing equipment. Copyright © 2008 John Wiley & Sons, Ltd.     

Poly(vinyl chloride) and its fire properties

This work provides an up‐to‐date review of the fire properties of poly(vinyl chloride) (PVC) materials, both rigid (unplasticized) and flexible (plasticized). The fire properties addressed include ignitability, ease of extinction (oxygen index), flame spread (small scale and intermediate scale), heat release, smoke obscuration, smoke toxicity, hydrogen chloride emission and decay, and performance in real‐scale fires. This comprehensive review includes a wide selection of references and tables illustrating the properties of PVC materials in comparison with those of other polymeric materials, including, in many instances, wood materials. The work puts these fire properties in perspective, showing that the heat release rate (the key fire property) of rigid PVC (and that of properly flame‐retarded flexible PVC) are among the lower values found for combustible materials. This work also shows that the smoke toxicity and smoke obscuration resulting from burning PVC materials in real‐scale fires is in the same range as those of other materials.     

Experimental studies of gypsum plasterboards and composite panels under fire conditions

Gypsum plasterboards are commonly used to protect the light gauge steel‐framed walls in buildings from fires. Single or multiple plasterboards can be used for this purpose, whereas recent research has proposed a composite panel with a layer of external insulation between two plasterboards. However, a good understanding of the thermal behaviour of these plasterboard panels under fire conditions is not known. Therefore, 15 small‐scale fire tests were conducted on plasterboard panels made of 13 and 16 mm plasterboards and four different types of insulations with varying thickness and density subject to standard fire conditions in AS 1530.4. Fire performance of single and multiple layers of gypsum plasterboards was assessed including the effects of interfaces between adjacent plasterboards. Effects of using external insulations such as glass fibre, rockwool and cellulose fibre were also determined. The thermal performance of composite panels developed from different insulating materials of varying densities and thicknesses was examined and compared. This paper presents the details of the fire tests conducted in this study and their valuable time–temperature data for the tested plasterboard panels. These data can be used for the purpose of developing and validating accurate thermal numerical models of these panels. Copyright © 2012 John Wiley & Sons, Ltd.     

消防炮在石化工业消防中的应用及推广

消防炮是现代石油化工工业消防不可缺少的重要技术装备,用于保护面积较大、火灾危险性较高而且价值较昂贵的重点工程的群组设备等要害场所,能及时、有效地扑灭较大规模的区域性火灾的灭火威力较大的灭火设备。文章介绍了消防炮的分类及主要特点,结合实例阐述其在石化工业消防中的应用情况。