8W AlGaN/GaN HEMT功率器件的研制

报道了基于国产衬底以及国产外延的AlGaN/GaN HEMT X波段功率器件的研究进展.利用国产衬底以及外延材料,优化了器件栅场板的结构,研制成功栅长0.35μm,栅宽为lmm的微波功率器件.该器件输出电流密度达到0.83A/mm,击穿电压大于100V,跨导为236mS/mm,截止频率(fT)达到30GHz,最大振荡频率(fmax)为32GHz,8GHz下在片进行连续波测试,漏端电压为40V时测试得到功率增益4.9dB,输出功率达8W,功率附加效率(PAE)为45%.     

X波段高输出功率凹栅AlGaN/GaN HEMT

使用自主研制的SiC衬底GaN HEMT外延材料,研制出高输出功率AlGaN/GaN HEMT,优化了器件研制工艺,比接触电阻率小于1.0×10-6Ω·cm2,电流崩塌参量小于10%,击穿电压大于80V.小栅宽器件工作电压达到40V,频率为8GHz时输出功率密度大于10W/mm.栅宽为2mm单胞器件,工作电压为28V,频率为8GHz时,输出功率为12.3W,功率增益为4.9dB,功率附加效率为35%.四胞内匹配总栅宽为8mm器件,工作电压为27V时,频率为8GHz时,输出功率为33.8W,功率增益为6.3dB,功率附加效率为41.77%,单胞器件和内匹配器件输出功率为目前国内该器件输出功率的最高结果.     

X波段高输出功率凹栅AlGaN/GaN HEMT

使用自主研制的SiC衬底GaN HEMT外延材料,研制出高输出功率AlGaN/GaN HEMT,优化了器件研制工艺,比接触电阻率小于1.0×10-6Ω·cm2,电流崩塌参量小于10%,击穿电压大于80V.小栅宽器件工作电压达到40V,频率为8GHz时输出功率密度大于10W/mm.栅宽为2mm单胞器件,工作电压为28V,频率为8GHz时,输出功率为12.3W,功率增益为4.9dB,功率附加效率为35%.四胞内匹配总栅宽为8mm器件,工作电压为27V时,频率为8GHz时,输出功率为33.8W,功率增益为6.3dB,功率附加效率为41.77%,单胞器件和内匹配器件输出功率为目前国内该器件输出功率的最高结果.     

高性能1mm SiC基AlGaN/GaN功率HEMT研制

在6H-SiC衬底上,外延生长了AlGaN/GaN HEMT结构,设计并实现了高性能1mm AlGaN/GaN微波功率HEMT,外延材料利用金属有机物化学气相淀积技术生长.测试表明,该lmm栅宽器件栅长为0.8μm,输出电流密度达到1.16A/mm,跨导为241mS/mm,击穿电压＞80V,特征频率达到20GHz,最大振荡频率为28GHz.5.4GHz连续波测试下功率增益为14.2dB,输出功率达4.1W,脉冲条件测试下功率增益为14.4dB,输出功率为5.2W,两端口阻抗特性显示了在微波应用中的良好潜力.     

高性能1mm SiC基AlGaN/GaN功率HEMT研制

在6H-SiC衬底上,外延生长了AlGaN/GaN HEMT结构,设计并实现了高性能1mm AlGaN/GaN微波功率HEMT,外延材料利用金属有机物化学气相淀积技术生长.测试表明,该lmm栅宽器件栅长为0.8μm,输出电流密度达到1.16A/mm,跨导为241mS/mm,击穿电压＞80V,特征频率达到20GHz,最大振荡频率为28GHz.5.4GHz连续波测试下功率增益为14.2dB,输出功率达4.1W,脉冲条件测试下功率增益为14.4dB,输出功率为5.2W,两端口阻抗特性显示了在微波应用中的良好潜力.     

蓝宝石衬底AlGaNöGaN 功率HEM Ts 研制

基于蓝宝石衬底的高微波特性 Al Ga N/Ga N HEMTs功率器件 ,器件采用了新的欧姆接触和新型空气桥方案。测试表明 ,器件电流密度 0 .784A/mm,跨导 1 97m S/mm,关态击穿电压 >80 V,截止态漏电很小 ,栅宽 1 mm的器件的单位截止频率 ( f T)达到 2 0 GHz,最大振荡频率 ( fmax) 2 8GHz,2 GHz脉冲测试下 ,栅宽 0 .75 mm器件 ,功率增益1 1 .8d B,输出功率 3 1 .2 d Bm,功率密度 1 .75 W/mm。     

基于国产外延材料的SiC基AlGaN/GaN HEMT器件研制

本文报道了基于国产外延材料的SiC基Al GaN/GaN高迁移率晶体管（HEMT）器件的研制,外延材料利用金属有机物化学气相淀积技术（MOCVD）生长,器件栅长0.8μm,输出电流密度达到0.94A/mm,在5.4GHz下,单指型管芯获得了3.1W/mm的连续波测试功率,与蓝宝石衬底的器件相比,由于自热效应的有效改善,输出功率能力大大提高.     

fT为77GHz的蓝宝石衬底0.25μm栅长AlGaN/GaN高电子迁移率功率器件

在蓝宝石衬底上用MOCVD技术生长的AlGaN/GaN结构上制作出0.25μm栅长的高电子迁移率功率晶体管.0.25μm栅长的单指器件测到峰值跨导为250mS/mm,特征频率为77GHz.功率器件的最大电流密度达到1.07A/mm.8GHz频率下在片测试80×10μm栅宽器件的输出功率为27.04dBm,同时功率附加效率达到26.5%.     

fT为77GHz的蓝宝石衬底0.25μm栅长AlGaN/GaN高电子迁移率功率器件

在蓝宝石衬底上用MOCVD技术生长的AlGaN/GaN结构上制作出0.25μm栅长的高电子迁移率功率晶体管.0.25μm栅长的单指器件测到峰值跨导为250mS/mm,特征频率为77GHz.功率器件的最大电流密度达到1.07A/mm.8GHz频率下在片测试80×10μm栅宽器件的输出功率为27.04dBm,同时功率附加效率达到26.5%.     

0.25μm Gate-Length AlGaN/GaN Power HEMTs on Sapphire with fT of 77GHz

在蓝宝石衬底上用MOCVD技术生长的AlGaN/GaN结构上制作出0.25μm栅长的高电子迁移率功率晶体管. 0.25μm栅长的单指器件测到峰值跨导为250mS/mm，特征频率为77GHz. 功率器件的最大电流密度达到1.07A/mm. 8GHz频率下在片测试80×10μm栅宽器件的输出功率为27.04dBm，同时功率附加效率达到26.5%.     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.