大尺寸KDP晶体生长开裂的尺度效应分析

在人工生长大尺寸KDP(磷酸二氢钾,KH2PO4)晶体过程中晶体会发生开裂现象,尤其是晶体生长到400mm左右时晶帽下端容易出现裂纹.为了研究KDP晶体的生长过程中的开裂机制,采用有限元方法模拟该晶体的生长过程,重点分析了晶体在不同生长尺寸的应力场分布规律,结果表明生长过程中晶体内部应力分布存在明显的尺度效应.当KDP晶体生长达到400mm时,晶帽下部受力逐渐由受压状态转变为受拉状态,根据KDP晶体材料抗拉不抗压的性质,此时开裂的机率增大.这一发现为下一步深入研究晶体生长开裂的损伤力学机制和寻找KDP晶体生长中的防裂措施奠定了基础.     

DCTA对KDP晶体的快速生长与光学性能的影响

环己二胺四乙酸(DCTA)作为一种新型添加剂被加入到KDP晶体生长溶液中。采用“点籽晶”快速生长技术, 在掺杂100×10^-6 DCTA的饱和溶液中, 生长了KDP晶体, 生长速度达20 mm/d。研究了这种新型添加剂DCTA对快速生长的KDP晶体的生长习性和光学质量的影响, 并与常用添加剂EDTA的影响效果进行了对比。研究发现, 在KDP晶体生长溶液中添加100×10^-6 DCTA使生长溶液的亚稳区宽度提高了约10℃, 晶体(100)面的生长速度提高了3~10倍; 生长出的晶体在紫外波段的透过率上升了2~8倍, 晶体内部的光散射大大减轻, 激光损伤阈值也有所提高。添加剂DCTA对KDP晶体生长及性能的改善作用比同等浓度的EDTA更加显著。     

KDP/KD*P晶体生长过程中柱面扩展的研究

目前在KDP/KD*P晶体的实际生长过程中,仍以传统降温法为主.在传统降温速度的基础上适当提高降温速度,可以加快KDP/KD*P晶体的生长速度,但与此同时有可能产生柱面扩展.为此,我们对不同生长环境下的KDP/KD*P晶体生长过程中柱面扩展进行了一系列研究.实验中所用KDP原料和去离子水均与生长大口径KDP晶体相同,其它各项条件也尽量模拟大口径KDP晶体生长过程中的实际情况.在晶体生长实验过程中通过研究不同条件下KDP/KD*P晶体的柱面扩展情况来研究柱面扩展对KDP/KD*P晶体光学质量影响的共同特点.通过分析和研究实验数据及晶体生长过程,我们认为在正常生长条件下引起柱面扩展的主要因素有两个溶液的过饱和度和籽晶柱面存在的缺陷.扩展部分的晶体的光学质量与本体部分差别较大,扩展部分对光的透过率在紫外部分下降很快,明显低于本体部分在这一波段的透过率.本体部分和扩展部分对光的透过率在其它波段差别不十分突出.     

KDP晶体包裹体的拉曼光谱研究

激光显微拉曼光谱对KDP晶体包裹体研究发现,相邻锥扇界附近的球形溶液包裹体串只有水溶液,而柱面扩展包藏和含高密度散射颗粒的KDP晶体都存在CO₂和H₂S等杂质分子.我们推断,柱、锥面包裹体成分的不同与晶体不同面的生长特征有关,CO₂等杂质气体分子的存在是柱面包裹体和散射颗粒形成的原因之一.     

硫酸盐掺杂对KDP晶体生长的影响

SO2-4是KDP原料中一种常见的杂质离子,通过传统降温法和“点籽晶”快速生长法研究了掺杂K2SO4的KDP晶体的生长.实验表明,硫酸根低浓度掺杂时可提高溶液的稳定性,促进晶体的生长,造成柱面扩展;高浓度时溶液稳定性遭到破坏,出现杂晶,晶体生长速度变慢,晶体出现开裂,柱面发生“楔化”.     

转速对快速法生长KDP晶体影响的实验与数值模拟研究

采用快速生长法在不同转速下生长了KDP晶体,对晶体生长过程中的现象进行了研究;运用fluent软件,采用多重参考模型和标准k-ε湍流模型对籽晶架和晶体在溶液中旋转产生的速度场进行了数值模拟,分析了不同转速对速度场和晶体长大对溶液稳定性的影响;结合实验现象与模拟结果分析可知,初始阶段适于KDP晶体快速生长的最优转速是100 r/min,随着晶体的长大,转速应适当降低。     

硫酸盐掺杂导致KDP晶体开裂的研究

采用传统降温法生长了掺杂不同浓度的SO42-离子KDP晶体,研究分析了晶体的宏观缺陷及开裂形式,从晶体生长角度初步分析了硫酸盐掺杂导致KDP晶体开裂的主要原因。实验表明,随着SO42-离子掺杂浓度的增大,KDP晶体的主要开裂形式是垂直于生长层{101}面的裂纹;晶体中裂纹存在的区域都分布有大量层层平行于生长层的母液包藏。随着SO42-离子掺杂浓度的进一步增大,晶体内包藏呈云雾状分布,裂纹不规则,晶体质量严重下降,透明度降低。     

Cr3+掺杂对快速生长KDP晶体的生长习性和光学性能的影响

采用快速法生长了掺杂不同Cr3+浓度的KDP晶体,测试了KDP晶体(100)面在不同Cr3+掺杂浓度下的生长速度及死区,表征了Cr3+掺杂的KDP晶体的Cr3+元素分布、透过光谱、散射颗粒分布和光损伤阈值.实验表明Cr3+易吸附在晶体(100)面,从而增大了(100)生长死区,并降低了(100)面生长速度.Cr3+使快...     

Ca2+离子对 KDP晶体生长习性及性能的影响

Ca^2＋是KDP原料中一种常见的杂质离子，通过传统降温法和“点籽晶”快速生长法研究了Ca^2＋离子对KDP晶体生长习性及性能的影响、实验表明，Ca^2＋低浓度掺杂时对溶液的稳定性及生长过程没有明显的影响；高浓度时溶液稳定性有所降低，经常出现杂品；快速生长时，晶体柱面易出现包藏，晶体的紫外透过呈下降趋势，晶体中散射颗粒密度随掺杂浓度的增加而增大、     

添加剂DTPA对KDP晶体快速生长及性能的影响研究

在添加1×10^-4 (mol/mol KDP) 二乙烯三胺五乙酸(DTPA)的溶液中, 利用“点籽晶”快速生长法生长了KDP晶体. 实验发现, 添加少量DTPA即可使不同饱和温度下的KDP生长溶液的亚稳区宽度均得到提高. 利用激光偏振干涉装置研究了不同浓度的DTPA对KDP晶体(100)面生长动力学的影响. 发现随DTPA掺杂量增加, 临界过饱和度(死区)一直降低, 生长速度则是先增加经过一个最大值后减小. 表征了晶体的光学透过率和晶体内部的杂质金属离子含量, 发现掺杂1×10^-4 (mol/mol) DTPA大幅提高了快速生长的KDP晶体在紫外区的透过率, 并有效地减少了进入晶体内部的杂质金属离子含量.     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...