Synthesis and vibrational properties of hematite (α-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>) nanoparticles

α- Fe₂O₃ nanoparticles have been synthesized by gel evaporation method in air at 300°C. The average size of as synthesized α-Fe₂O₃ nanoparticle was estimated to be 30 nm and the particles were of good crystalline nature. Shape of the nanoparticles were slightly deviated from spherical which is attributed to the asymmetric growth of primary nuclei. MicroRaman and X-ray diffraction results have shown mixed phases of α-Fe₂O₃ and γ-Fe₂O₃. However, the α-Fe₂O₃ phase is more predominant than γ-Fe₂O₃ due to the incomplete nucleation of α-Fe₂O₃ particles at the size of 30 nm. The vibrating sample magnetometer measurement shows that the nanoparticles possess ferromagnetic property.     

Synthesis and characterization of hydroxyapatite by microwave heating using CaSO<Subscript>4</Subscript>·2H<Subscript>2</Subscript>O and Ca(OH)<Subscript>2</Subscript> as calcium source

In this paper, synthesis of hydroxyapatite (HAp) in the absence or presence of 1.05 wt% magnesium oxide, as sintering additive, by heating in a microwave oven was studied. For this purpose, CaSO₄·2H₂O, Ca(OH)₂, Mg(OH)₂ and (NH₄)₂HPO₄ were used as raw materials. The total chemical reactions for all the studied compositions were observed after a 3 h microwave treatment. In case of pure hydroxyapatite, a powder with needle-like grains results. In the presence of Mg(OH)₂, the (Mg, Ca₂)·O·(HPO₄)₂·H₂O hydrated phosphate is formed besides hydroxyapatite. Pure hydroxyapatite, thermally treated at 1,200 °C, mostly transforms in β-Ca₃P₂O₈. By adding MgO into the precursor mixture, hydroxyapatite was stabilised, and found in a much greater proportion at 1,200 °C. After the thermal treatment, the hydroxyapatite, analysed by electronic microscopy, shows a prismatic morphology originating in its initial state.     

CeO<Subscript>2</Subscript> and Co<Subscript>3</Subscript>O<Subscript>4</Subscript>–CeO<Subscript>2</Subscript> nanoparticles: effect of the synthesis method on the structure and catalytic properties in COPrOx and methanation reactions

CeO₂ and Co₃O₄–CeO₂ nanoparticles were synthesized, thoroughly characterized, and evaluated in the COPrOx reaction. The CeO₂ nanoparticles were synthesized by the diffusion-controlled precipitation method with ethylene glycol. A notably higher yield was obtained when H₂O₂ was used in the synthesis procedure. For comparison, two commercial samples of CeO₂ nanoparticles (Nyacol^®)—one calcined and the other sintered—were also studied. Catalytic results of bare CeO₂ calcined at 500 °C showed a strong influence of the method of synthesis. Despite having similar BET area values, the CeO₂ synthesized without H₂O₂ was the most active sample. Co₃O₄–CeO₂ catalysts with three different Co/(Co + Ce) atomic ratios, 0.1, 0.3, and 0.5, were prepared by the wet impregnation of the CeO₂ nanoparticles. TEM and STEM observations showed that impregnation produced mixed oxides composed of small CeO₂ nanoparticles located both over the surface and inside the Co₃O₄ crystals. The mixed oxide catalysts prepared with a cobalt atomic ratio of 0.5 showed methane formation, which started at 200 °C due to the reaction between CO₂ and H₂. However, above 250 °C, the reaction between CO and H₂ became important, thus contributing to CO elimination with a small H₂ loss. As a result, CO could be totally eliminated in a wide temperature range, from 200 to 400 °C. The methanation reaction was favored by the reduction of the cobalt oxide, as suggested by the TPR experiments. This result is probably originated in Ce–Co interactions, related to the method of synthesis and the surface area of the mixed oxides obtained.     

Y<Subscript>3−x</Subscript>Gd<Subscript>x</Subscript>Fe<Subscript>5</Subscript>O<Subscript>12</Subscript>: controlled synthesis,characterization and investigation of its magnetic properties

Gadolinium substituted yttrium iron garnet (Gd: YIG: Y_3?xGd_xFe₅O₁₂ where x?=?0, 0.25, 0.5, 0.75, 1, 1.25, 1.5) nanopowders were synthesized by microwave hydrothermal method. Phase structure of synthesized powders was examined using fourier-transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) which revealed a cubic garnet structure. Spherical-like morphology of synthesized powders was confirmed by field emission scanning electron microscopy (FESEM) studies. The synthesized powders were sintered at 1100?°C for 60 min using microwave furnace and characterized by using XRD and FESEM. Magnetic properties such as saturation magnetization and Curie temperature were measured using vibration sample magnetometer (VSM) and differential scanning calorimetry (DSC) studies respectively. Temperature stability of magnetization was measured using pulse magnetometer and complex permeability was measured over a frequency range of 100 kHz–1.8 GHz. The obtained results showed that the saturation magnetization as well as permeability decrease while curie temperature and temperature stability increase with Gd concentration. It is concluded that substitution of Gd makes the YIG better microwave magnetic material, which may be used in high power non-reciprocal microwave devices in the microwave region.     

Structural and electrochemical properties of α-MnO<Subscript>2</Subscript> doped with cobalt

In this study, co-doped and undoped MnO₂ samples were prepared by redox reaction in acidic medium. X-ray diffraction patterns of pure and doped samples revealed that they crystallized in the α-form with a (2 × 2) tunnel structure. Chemical analysis indicated an increase in the concentration of K⁺ cations upon Co doping resulting in higher thermal stability. Magnetic properties show the coexistence of Mn⁴⁺ and Mn³⁺ valence states, with reduced amount of Mn³⁺ ions after the doping process. Co-doped MnO₂ has better rechargeability and capacity retention than pure α-MnO₂, but the reduction of the capacity fading occurs at the expense of the initial capacity.     

Uniformly dispersed Pd nanoparticles anchored Co(OH)<Subscript>2</Subscript>/Cu(OH)<Subscript>2</Subscript> hierarchical nanotube array as high active structured catalyst for Suzuki–Miyaura coupling reactions

Up to now, although tremendous effort has been made in exploring Pd-based catalysts for the Suzuki–Miyaura coupling reactions, there is still much room to enhance its catalytic performance by synthesis catalyst with define-designed and tailored structure. Herein, a new kind of Pd-based structured catalyst with hierarchical hollow structure (Pd/Co(OH)₂/Cu(OH)₂/copper foam) has been successfully synthesized by three facile steps. As framework, the hierarchical hollow nanoarray structure of Co(OH)₂/Cu(OH)₂/copper foam is fabricated by immersion and electrolytic deposition methods. Uniformly dispersed Pd nanoparticles with a narrow size distribution (1.5?±?0.2 nm) are anchored on the surface of the hierarchical nanotube array through an in situ spontaneous redox reaction between Co(OH)₂ and PdCl₄^2? without any surfactant at room temperature. Compared with other synthesis approaches, it just takes less than 1 h for the whole fabrication process in our strategy, exhibiting very high efficiency. In order to evaluate the catalytic performance of the as-prepared structured catalyst, 16 kinds of reagents were chosen as substrates for Suzuki–Miyaura coupling reaction, exhibiting excellent activity and reusability under mild conditions. We hope this simple and efficient method will open a new strategy to design and prepare structured catalysts.     

Preparation of β-Ca<Subscript>3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript>/Poly(D,L-lactide) and β-Ca<Subscript>3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript>/Poly(ε-caprolactone) Biocomposite Implants for Bone Substitution

Highly permeable macroporous implants of various architectures for bone grafting have been fabricated by thermal extrusion 3D printing using highly filled β-Ca₃(PO₄)₂/poly(D,L-lactide) (degree of filling up to 70 wt %) and β-Ca₃(PO₄)₂/poly(ε-caprolactone) (degree of filling up to 70 wt %) composite filaments. To modify the surface of the composite macroporous implants with the aim of improving their wettability by saline solutions, we have proposed exposing them to a cathode discharge plasma (2.5 W, air as plasma gas) in combination with subsequent etching in a 0.5 M citric acid solution. It has been shown that the main contribution to changes in the wettability (contact angle) of the composites is made by the changes produced in their surface morphology by etching in a low-temperature plasma and citric acid. An alternative approach to surface modification of the composites is to produce a carbonate hydroxyapatite layer via precipitation from a simulated body fluid solution a factor of 5 supersaturated relative to its natural analog (5xSBF).     

Synthesis and Structure of the Np(VII) Complex with Guanidinium,Li[C(NH<Subscript>2</Subscript>)<Subscript>3</Subscript>]<Subscript>2</Subscript>[NpO<Subscript>4</Subscript>(OH)<Subscript>2</Subscript>]·6H<Subscript>2</Subscript>O

The previously unknown Np(VII) compound Li[C(NH₂)₃]₂[NpO₄(OH)₂]·6H₂O (I), containing organic cations, was synthesized and studied by single crystal X-ray diffraction. In contrast to the relatively numerous structurally characterized salts of [NpO₄(OH)₂]^3– anions with Na⁺, K⁺, Rb⁺, and Cs⁺ cations, which were prepared only from strongly alkaline media, crystals of I were isolated from solutions with a very low concentration of OH^– ions (about 0.1 M). The compound is relatively stable in storage in the dry form, but is strongly hygroscopic. In the structure of I, there are two independent Np(VII) atoms with the oxygen surrounding in the form of tetragonal bipyramids. In contrast to the other salts of the [NpO₄(OH)₂]^3– anions with singlecharged alkali metal cations, the C(NH₂) ₃ ⁺ ions and hydrated Li⁺ ions in I interact with the oxygen surrounding of Np(VII) only via hydrogen bonds of types O_w–H···O and N–H···O with the formation of a three-dimensional H-bond network.     

Thermal analysis,AC conductivity and dielectric relaxation in Bis(2-methoxyanilinium) hexabromidostannate(IV) dihydrate: (C<Subscript>7</Subscript>H<Subscript>10</Subscript>NO)<Subscript>2</Subscript>SnBr<Subscript>6</Subscript>·2H<Subscript>2</Subscript>O

The (C₇H₁₀NO)₂SnBr₆·2H₂O compound is characterized by using the X-ray powder analysis, thermogravimetric analyses, differential scanning calorimetry (DSC) and complex impedance spectroscopic data. This compound exhibits a phase transition at 300 K which is characterized by differential scanning calorimetry, AC conductivity and dielectric measurements. The measurements of impedance spectroscopic are carried out in the frequency range from 100 Hz to 1 MHz with temperatures varying between 275 and 330 K. The impedance measurements indicate that the electrical properties are strongly temperature dependent. Nyquist plots (?Z′′ versus Z′) show that the conductivity behavior is accurately represented by an Rp//CPE equivalent electrical circuit model. Besides, the frequency dependence of conductivity follows Jonscher’s dynamical law with the relation: \(\sigma (\omega ,T)={\sigma _{DC}}+A(T){\omega ^{S(T)}}\). The relaxation mechanism can be observed in the complex modulus analysis M^* and the complex polarizability α^*.     

Controlled synthesis of mesoporous β-Ni(OH)2 and NiO nanospheres with enhanced electrochemical performance

Uniform mesoporous β-Ni(OH)₂ and NiO nanospheres with hierarchical structures were synthesized by a facile complexation–precipitation method. The effects of ammonia and citrate on the structure and morphology of the products were thoroughly investigated by X-ray powder diffraction, scanning electron microscopy, transmission electron microscopy and nitrogen adsorption–desorption measurements. The results indicated that ammonia played an important role for the formation of flowerlike spheres assembled from nanosheets. The addition of citrate could remarkably reduce the particle sizes and increase the specific surface areas of flowerlike spheres. A possible formation mechanism based on the experimental results was proposed to understand their growing procedures. β-Ni(OH)₂ and NiO nanospheres prepared with the addition of citrate showed excellent capacitive properties due to their mesoporous structures and large surface areas, suggesting the importance of controlled synthesis of hierarchical nanostructures for their applications.     

Synthesis and properties of actinide dimolybdate complexes M<Subscript>2</Subscript>[AnO<Subscript>2</Subscript>(MoO<Subscript>4</Subscript>)<Subscript>2</Subscript>]·H<Subscript>2</Subscript>O (M = Rb,Cs; An = Np,Pu)

New Np(VI) and Pu(VI) dimolybdates Rb₂NpO₂(MoO₄)₂·H₂O (I), Cs₂NpO₂(MoO₄)₂·H₂O (II), Cs₂PuO₂(MoO₄)₂·H₂O (III), and Rb₂PuO₂(MoO₄)₂·H₂O (IV) were synthesized under hydrothermal conditions. The crystal structures of the compounds were determined, and their absorption spectra in the UV, visible, and IR ranges were measured. The compounds crystallize in the monoclinic system. Their crystal structure is based on [AnO₂(MoO₄)₂]_n^2n– anionic layers (An = Np, Pu) formed by (AnO₂)O₅ pentagonal bipyramids and MoO₄ tetrahedra, sharing common vertices. Each An atom in the layer is bonded to other five An atoms via MoO₄ tetrahedra with the formation of a 4343² network. The effect of the ionic radius of the outer-sphere cation on the parameters of the crystal structure and features of the absorption spectra is discussed.     

Crystal structure of a Pu(VII) potassium salt,K<Subscript>3</Subscript>PuO<Subscript>4</Subscript>(OH)<Subscript>2</Subscript>·2H<Subscript>2</Subscript>O

A new Pu(VII) compound, K₃PuO₄(OH)₂·2H₂O, was synthesized, and its structure was studied by single crystal X-ray diffraction. This compound is isostructural to the previously described K₃NpO₄(OH)₂·2H₂O. The structure of the latter compound was redetermined to obtain more precise interatomic distances in the NpO₂(OH) ₂ ^3? anion. Changes in An-O bond lengths in the tetragon-bipyramidal coordination polyhedron of the compounds K₃AnO₄(OH)₂·2H₂O in going from Np(VII) to Pu(VII) were considered.     

Pt nanoparticles inside the mesopores of TiO<Subscript>2</Subscript>–MCM-48: synthesis,characterization and catalytic activity for CO oxidation

TiO₂ and Pt nanoparticles were deposited in the channels of siliceous MCM-48 via a sequential incipient wetness-impregnation method employing (NH₄)₂PtCl₄ as platinum source. The resulting composite Pt/TiO₂–MCM-48 (1 wt% Pt, ca. 3 wt% Ti) was characterized using XRD, TEM, nitrogen physisorption, hydrogen chemisorption, UV–vis spectroscopy, and XPS; its catalytic activity for CO oxidation was also explored. These data were compared with those of Pt/MCM-48 prepared via an analogous route. The results reveal that the platinum was deposited inside the intact pore system in both cases. It remains inside upon mild reduction but tends to segregate out of the pore system at higher reduction temperatures or during CO oxidation. Both composites were found to be highly active in CO oxidation, with 50% conversion at 460–475 K after activation of the unreduced catalysts in the (net oxidizing) feed. Striking differences in this activation process between Pt/MCM-48 and Pt/TiO₂–MCM-48 suggest that the precursor reduction is influenced by an interaction with the TiO₂ component in the latter.     

Synthesis and characterization of TiO<Subscript>2</Subscript>–NiO and TiO<Subscript>2</Subscript>–WO<Subscript>3</Subscript> nanocomposites

TiO₂–NiO and TiO₂–WO₃ nanocomposites were prepared by hydrothermal and surface modification methods. The samples were analyzed using X-ray diffraction, Scanning Electron Microscope images, Transmission Electron Microscope, Energy dispersive analysis, Zeta potential, Electrophoretic mobility and Photocatalysis activity measurement. XRD data sets of TiO₂–NiO, TiO₂–WO₃ powder nanocomposite have been studied for the inclusion of NiO, WO₃ on the anatase-rutile mixture phase of TiO₂ by Rietveld refinement. The cell parameters, phase fraction, the average grain size, strain and bond lengths between atoms of individual phases have been reported in the present work. Shifted positional co-ordinates of individual atoms in each phase have also been observed.     

Structure and properties of CaF<Subscript>2</Subscript>–B<Subscript>2</Subscript>O<Subscript>3</Subscript> glasses

FTIR spectroscopy has been employed to investigate the structure of CaF₂–B₂O₃ glasses. It is proposed that CaF₂ partially modifies the borate network forming \textCa _{1 / 2} ²⁺ [\textBO _{3 / 2} \textF] ^- {\text{Ca}}_{ 1 / 2}^{ 2+ } [{\text{BO}}_{ 3 / 2} {\text{F]}}^{ - } units. The rest of CaF₂ is assumed to build an amorphous network formed of CaF₄ tetrahedra. Analysis of density and molar volume revealed that the volume of CaF₄ tetrahedron in the studied glasses is slightly greater than that in the crystalline form. Data of density, molar volume, and electric conductivity have been correlated with the glass structure. As far as the authors know, CaF₂–B₂O₃ glasses are investigated for the first time.     

Effect of refractory nitride nanoadditives on the properties of (Bi,Pb)<Subscript>2</Subscript>Sr<Subscript>2</Subscript>Ca<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript>10+δ</Subscript>

We have investigated the interaction between (Bi,Pb)₂Sr₂Ca₂Cu₃O_10+δ (Bi-2223) and small additions (0.05–0.3 wt %) of nitride powders (TaN, AlN, HfN, NbN, Si₃N₄, TiN, and ZrN) with a particle size from 0.02 to above 0.5 μm and the effect of these nitrides on the microstructure, phase composition, distribution, and morphology of the resulting second-phase inclusions. The concentration and particle size of the nitrides and sintering conditions are shown to influence the superconducting transition temperature T _c, critical current density j _c, irreversible remanent magnetization, bulk density, and mechanical properties of the Bi-2223/nitride composites.     

Synthesis,electronic state,and particle size stabilization of nanoparticulate [Co(OH)<Subscript>2</Subscript>(H<Subscript>3</Subscript>O)<Stack><Subscript>δ</Subscript><Superscript>+</Superscript></Stack>]<Superscript>δ+</Superscript>

We have synthesized nanoparticulate cobalt(II) hydroxide containing Co²⁺ in tetrahedral oxygen coordination (Co _Td ²⁺ ), atypical of such systems: nano- [Co(OH)₂(H₃O) _δ ⁺ ]^δ+. The (Co _Td ²⁺ ) coordination in the hydroxide is inferred from its electronic diffuse reflectance spectrum, which shows a multiplet of strong absorption bands at 14500, 15000, and 16000 cm^?1 (⁴ A ₂(F)-⁴ T ₁(P) transition). Nanoparticulate cobalt(II) hydroxide forms in a weakly acidic medium under essentially nonequilibrium conditions due to supersaturation (by three to four orders of magnitude) with the starting reagents (CoCl₂ and LiOH) at the instant of the formation of the poorly soluble phase Co(OH)₂. Presumably, colloidal particles of nanoparticulate cobalt(II) hydroxide in a weakly acidic aqueous medium have a positive surface charge, compensated by a counter-ion (Cl^?) layer: nano-[Co(OH)₂(H₃O) _δ ⁺ ]^δ+ · δCl^?. The XRD patterns of pastes (gels) containing this hydroxide show three broad-ened lines with d = 5.31 (2θ = 16.7°), 2.77 (2θ = 32.3°), and 2.32 Å (2θ = 38.8°). According to small-angle X-ray scattering data, nano-[Co(OH)₂(H₃O) _δ ⁺ ]^δ+ has a narrow particle size distribution (1.0–2.0 nm). Synthesis and storage conditions are identified which ensure stabilization of the electronic state and particle size of nano-[Co(OH)₂(H₃O) _δ ⁺ ]^δ+ for a long time.     

Microstructure,interfaces and creep behaviour of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–Sm<Subscript>2</Subscript>O<Subscript>3</Subscript> (ZrO<Subscript>2</Subscript>) eutectic ceramic composites

New compositions in the melt-grown eutectic ceramics field are investigated for thermomechanical applications. This paper is focused on the Al₂O₃–Sm₂O₃–(ZrO₂) system. The studied compositions give rise to interconnected microstructures without anisotropy along the growth direction. At variance with the binary eutectic Al₂O₃–SmAlO₃, the homogeneity of the microstructure of the Al₂O₃–SmAlO₃–ZrO₂ ternary eutectic is less sensitive to the growth rate. Interfaces between the alumina and perovskite phases are investigated by high-resolution transmission electron microscopy (TEM). They are semi-coherent. In stepped interfaces, the facets are parallel to dense planes of each phase. The steps have a dislocation character and may accommodate both misfits. The ternary eutectic displays a very good creep behaviour with strain rates very close to those obtained on other previously studied eutectics in the Al₂O₃–RE₂O₃(RE = Y, Gd, Er)–ZrO₂ systems. The deformation micromechanisms are analysed by TEM in the three eutectic phases. After creep, dislocations are present in every phase. The activation of unusual slip systems (pyramidal slip in the alumina phase) shows that high local stresses can be reached. The presence of dislocation networks with low energy configurations is consistent with predominance of dislocation climb processes controlled by bulk diffusion.     

Glasses formation,characterization, and crystal-structure determination in the Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>–Sb<Subscript>2</Subscript>O<Subscript>3</Subscript>–TeO<Subscript>2</Subscript> system prepared in an air

A glass-forming domain is found and studied within Bi₂O₃–Sb₂O₃–TeO₂ system. The glasses composition were obtained in pseudo-binary xSbO_1.5, (1−x)TeO₂ for 0.05 ≤ x ≤ 0.20. The constitution of glasses in the system Sb₂O₃–TeO₂ was investigated by DSC, Raman, and Infrared spectroscopy. The influence of a gradual addition of the modifier oxides on the coordination geometry of tellurium atoms has been elucidated based Infrared and Raman studies and showed the transition of TeO₄, TeO₃₊₁, and TeO₃ units with increasing Sb₂O₃ content. XRD results reveal the presence of three crystalline: γ-TeO₂, α-TeO₂, and SbTe₃O₈ phases during the crystallization process. The density of glasses has been measured. The investigation in the ternary system by the solid state reaction using XRD reveals the existence of a solid solution Bi_1−x Sb_1−x Te_2x O₄ isotopic to BiSbO₄ with 0 ≤ x ≤ 0.1.     

Crystal growth,X-ray diffraction characterization,and Mössbauer spectroscopy of FeIn<Subscript>2</Subscript>S<Subscript>4</Subscript>-In<Subscript>2</Subscript>S<Subscript>3</Subscript> solid solutions

Crystals of (FeIn₂S₄)_{1 ? x} (In₂S₃) _x solid solutions consisting of large blocks have been grown by directional solidification (horizontal Bridgman process). FeIn₂S₄, In₂S₃, and the solid solutions are shown to crystallize in the spinel structure. The composition dependence of their unit-cell parameter a follows Vegard's law. The local states of the Fe ions in the solid solutions have been studied by Mössbauer spectroscopy in a transmission geometry.