BaFe<Subscript>12</Subscript>O<Subscript>19</Subscript> films produced from BaFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/α-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> heterostructures

BaFe₁₂O₁₉ hexaferrite films have been produced on thermally oxidized single-crystal silicon (SiO₂/Si) substrates by sequential ion-beam sputtering of BaFe₂O₄ and α-Fe₂O₃ targets in an argon-oxygen atmosphere. Their crystal structure has been studied, and the origin of the impurity phases forming during heat treatment has been identified. The results show that heat treatment may lead to the formation of eutectic melts. As a result, the hexaferrite films may contain spherulites.     

Catalytic combustion of methane over Pt and PdO-supported CeO<Subscript>2</Subscript>–ZrO<Subscript>2</Subscript>–Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>/γ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

Catalytic combustion of methane was investigated on Pt and PdO-supported CeO₂–ZrO₂–Bi₂O₃/γ-Al₂O₃ catalysts prepared by a wet impregnation method in the presence of polyvinylpyrrolidone. The catalysts were characterized by X-ray fluorescence analysis, X-ray powder diffraction, X-ray photoelectron spectra, transmission electron microscopy, and BET specific surface area measurements. The Pt/CeO₂–ZrO₂–Bi₂O₃/γ-Al₂O₃ and PdO/CeO₂–ZrO₂–Bi₂O₃/γ-Al₂O₃ catalysts were selective for the total oxidation of methane into carbon dioxide and steam, and no by-products such as HCHO, CO, and H₂ were obtained. The catalytic activities of the PdO/CeO₂–ZrO₂–Bi₂O₃/γ-Al₂O₃ catalysts were relatively higher than those of the Pt-supported catalysts, due to the facile re-oxidation of metallic Pd into PdO based on lattice oxygen supplied from the CeO₂–ZrO₂–Bi₂O₃ bulk. A decrease in the calcination temperature during the preparation process was found to be effective in enhancing the specific surface area of the catalysts, whereby particle agglomeration was inhibited. Optimization of the PdO amount and calcination temperature enabled complete oxidation of methane at temperatures as low as 320 °C on the 11.6 wt% PdO/CeO₂–ZrO₂–Bi₂O₃/γ-Al₂O₃ catalyst prepared at 400 °C.     

Atomistic structure and energetics of interface between Mn-doped γ-Ga<Subscript>2</Subscript>O<Subscript>3</Subscript> and MgAl<Subscript>2</Subscript>O<Subscript>4</Subscript>

The interface between an Mn-doped γ-gallium oxide (Ga₂O₃) thin film and an MgAl₂O₄ (001) substrate has been investigated using high-resolution transmission electron microscopy (HRTEM), high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM), and first-principles calculations. A high-quality Mn-doped γ-Ga₂O₃ film with a defective spinel structure has been epitaxially grown by pulsed laser deposition. The γ-Ga₂O₃ crystal shows an uniform tetragonal distortion with a tetragonality of 1.05 throughout the film thickness of 75 nm. HRTEM and HAADF-STEM observations reveal that the γ-Ga₂O₃ and MgAl₂O₄ crystals form a coherent interface without any interfacial layers or precipitates. The atomistic structure and energies are theoretically evaluated for the interfaces with two types of termination plane, i.e., Mg- and Al₂O₄-termination of MgAl₂O₄. The cation sublattice is found to be continuous for both interfaces despite the defective spinel structure of Mn-doped γ-Ga₂O₃ with some vacant cation sites. The Al₂O₄-termination shows a lower interfacial energy than the Mg-termination under most conditions of the chemical potentials. This behavior is attributed to the energetic preference of the Mn–Al₂O₄ local configuration at the interface.     

Superconducting Bands Stabilizing Superconductivity in YBa<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript>7</Subscript> and MgB<Subscript>2</Subscript>

It is shown that the ceramic superconductor YBa₂Cu₃O₇ as well as the superconducting intermetallic compound MgB₂ possesses a narrow, partly filled “superconducting band” with Wannier functions of special symmetry in their band structures. This result corroborates previous observations about the band structures of numerous superconductors and non-superconductors showing that evidently superconductivity is always connected with such superconducting bands. These findings are interpreted in the framework of a nonadiabatic extension of the Heisenberg model. Within this new group-theoretical model of correlated systems, Cooper pairs are stabilized by a nonadiabatic mechanism of constraining forces effective in narrow superconducting bands. The formation of Cooper pairs in a superconducting band is mediated by the energetically lowest boson excitations in the considered material that carry the crystal-spin angular momentum 1⋅ℏ. These crystal-spin-1 bosons are proposed to determine whether the material is a conventional low-T _c or a high-T _c superconductor. This interpretation provides the electron–phonon mechanism that enters the BCS theory in conventional superconductors.     

Growth and structure of Mg(Fe<Subscript>0.8</Subscript>Ga<Subscript>0.2</Subscript>)<Subscript>2</Subscript>O<Subscript>4 − δ</Subscript> films

Films 150–200 nm in thickness, with the nominal composition Mg(Fe_0.8Ga_0.2)₂O_{4 − δ} have been grown on (100) single-crystal silicon substrates by ion-beam sputtering in vacuum. The effect of growth and annealing conditions on the crystal structure and morphology of the films has been studied, and the thermal conditions for the growth of spinel-structure films have been optimized.     

Microwave and photoluminesent characterizations of (Ca<Subscript>2</Subscript>Mg<Subscript>3</Subscript>)(X<Subscript>1.75</Subscript>Sb<Subscript>0.25</Subscript>)TiO<Subscript>12</Subscript> [X = Nb and Ta] ceramics

(Ca₂Mg₃)(X_1.75Sb_0.25)TiO₁₂ [X = Nb and Ta] ceramics are prepared through the conventional solid-state route. The samples are calcined at 1,100 and 1,180 °C, and are sintered at 1,250 and 1,375 °C. The substitution of Sb decreases the calcination and sintering temperatures of pure (Ca₂Mg₃)(Nb/Ta)₂TiO₁₂. The structure of the samples is analyzed using X-ray diffraction method. The microstructure of the sintered pellet is studied using scanning electron microscopy. The dielectric properties such as dielectric constant (ε_r), quality factor (Q_uxf) and temperature coefficient of resonant frequency (τ_f) are measured in the microwave frequency region. By Sb substitution, thermal stability is achieved, with the increase in dielectric constant, without much change in the quality factor. The materials have intense emission lines in the wavelength region 500–700 nm. The compositions have good microwave dielectric properties and photoluminescence and hence are suitable for dielectric resonator and ceramic laser applications.     

High-damping and high-rigidity composites of Al<Subscript>2</Subscript>TiO<Subscript>5</Subscript>–MgTi<Subscript>2</Subscript>O<Subscript>5</Subscript> ceramics and acrylic resin

High-damping materials are widely used in engineering fields. In order to increase the precision of vibration control to different levels, high-damping materials with high-rigidity are required. This study attempts to develop a new high-damping high-rigidity material using ductile ceramics based on the Al₂TiO₅–MgTi₂O₅ system, which has many continuous microcracks along the grain boundaries. Ductile ceramics have high internal friction (Q ⁻¹ = 0.01–0.037), but very low rigidity (<10 GPa). The rigidity of Al₂TiO₅–MgTi₂O₅ ceramics was improved by combining them with a polymer such as acrylic resin. The Young’s modulus and internal friction of the composites of Al₂TiO₅–MgTi₂O₅ ceramics and acrylic resin are investigated. They show high-damping capacity (Q ⁻¹ = 0.03–0.04) with high rigidity (E = 50–60 GPa), and their properties depend on those of the polymer. Thus, the composites fabricated using the above method can serve as high-damping high-rigidity materials.     

Magnetic Anomalies and Electronic Structure of Ce<Subscript>2</Subscript>Cu<Subscript>2</Subscript>Mg and Ce<Subscript>2</Subscript>Pd<Subscript>2</Subscript>Mg

The intermetallic compounds RE ₂Cu₂Mg and RE ₂Pd₂Mg (RE=La, Ce) were prepared and characterized by magnetic susceptibility and heat-capacity measurements. They crystallize with an ordered U₃Si₂ type structure (space group P4/mbm) and the cerium compounds contain stable trivalent cerium ions, which undergo antiferromagnetic ordering at ∼7.5 and ∼4 K, respectively. In high magnetic fields Ce₂Cu₂Mg exhibits spin reorientation with critical field strength of 40 kOe at 5 K. The data are compared to the non-magnetic isotypic compounds La₂ T ₂Mg (T=Cu, Ni, Pd) and to the already reported intermediate valent Ce₂Ni₂Mg.     

Syntheses and proton conductivity of mesoporous Nd<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> and NdOCl–SiO<Subscript>2</Subscript> composites

Two mesoporous oxide composites of Nd₂O₃–SiO₂ and NdOCl–SiO₂ were synthesized using SBA-15 as a template and neodymium nitrate or neodymium chloride as a precursor. The porous Nd₂O₃–SiO₂ with a SBA-15-like structure has amorphous walls and the porous NdOCl–SiO₂ with a replicated structure of SBA-15 has crystalline walls. These porous materials were characterized by X-ray diffraction, transmission electron microscopy and nitrogen adsorption/desorption. They exhibited significant proton conductivities in the presence of moisture at low temperatures and the highest conductivity observed was 4.55 × 10⁻⁴ S/cm at 47 °C in wet air (RH = 28.6%).     

Dual relaxation behaviors and large electrostrictive properties of Bi<Subscript>0.5</Subscript>Na<Subscript>0.5</Subscript>TiO<Subscript>3</Subscript>–Sr<Subscript>0.85</Subscript>Bi<Subscript>0.1</Subscript>TiO<Subscript>3</Subscript> ceramics

Lead-free ceramics (1???x)Bi_0.5Na_0.5TiO₃–xSr_0.85Bi_0.1TiO₃ (BNT–xSBT, x?=?0.4, 0.5, 0.6 and 0.7) were prepared by a solid-state reaction process. Coexistence of ferroelectric relaxation at low temperature and Maxwell–Wagner dielectric relaxation at high temperature was revealed for the first time in this system. Meanwhile, hysteresis-free P–E loops combined with a very high piezoelectric strain coefficient (d₃₃) of 1658 pC/N concurrently with large electrostrictive coefficient Q?=?0.287 m⁴C^?2 were achieved. The ferroelectric relaxor behavior and large electrostrictive strain might be linked to easy reorientation and reversal of ergodic PNRs and the combined effect of Bi off-center position and lone pair electrons.     

Microstructure and properties of the Ba<Subscript>0.75−x</Subscript>Ca<Subscript>x</Subscript>La<Subscript>0.25</Subscript>Fe<Subscript>11.6</Subscript>Co<Subscript>0.25</Subscript>Ti<Subscript>0.15</Subscript>O<Subscript>19</Subscript> hexaferrites

In the case of Ti⁴⁺ remain unchanged, the Ca²⁺ substituted Ba_0.75?xCa_xLa_0.25Fe_11.6Co_0.25Ti_0.15O₁₉ (0?≤?x?≤?0.05) were prepared by conventional solid-state reaction method at temperature of 1280 °C. A ball-to-power weight ratio of 10:1. Their crystal structure and magnetic properties were mainly investigated. The results show that the single magnetoplumbite phase structure transformed into the multiphase structure. Meanwhile, the small amount of α-Fe₂O₃ phase existed in M-type phase. The micrographs were observed by a field emission scanning electron microscopy (SEM). Vibrating sample magnetometer (VSM) was used to analyze the magnetic properties. The saturation magnetization (M _s ) first increases then decreases when x from 0 to 0.03. But, when x from 0.03 to 0.05, the saturation magnetization (M _s ) first increases then decreases too. The maximum value is at x?=?0.04 (M _s ?=?70.73 emu/g). The value of coercivity (H _c ) first increases then decreases when x from 0 to 0.04. But, the value increased when x from 0.04 to 0.05. The maximum value is at x?=?0.02 (H _c ?=?1691 Oe).     

Crystallization and microstructural evolution of MgO–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript>–TiO<Subscript>2</Subscript>–La<Subscript>2</Subscript>O<Subscript>3</Subscript> glass-ceramics

Crystallization and microstructure of glasses with the molar compositions 1MgO·1.2Al₂O₃·2.8SiO₂·1.2TiO₂·xLa₂O₃ (x = 0.1 and 0.4) were thermally treated at different temperatures in the range from 950 to 1250 °C and then analyzed by X-ray diffraction and scanning electron microscopy, in combination with energy-dispersive X-ray spectroscopy and electron backscatter diffraction. It was found that the microstructure is first homogeneous with the precipitation of randomly distributed crystals and then indialite domains with embedded perrierite and rutile crystals are formed. For higher temperatures or prolonged times, more domains appear and expand into the bulk of the sample. Finally, the entire sample consists of the indialite domains and the boundaries that are enriched in rutile, perrierite, and magnesium aluminotitanate. Nevertheless, very distinct differences are observed between the samples with different La₂O₃ concentrations. For the sample with x = 0.4, the domains were detected at lower temperatures, while the quantity and size of the domains increase faster due to the promoted precipitation of indialite. For the sample with x = 0.1, in addition to the domain boundaries, secondary boundaries between the “regions” (assemblages of the domains) are observed in a larger length scale. The average size of the crystalline phases found between the “regions” is larger than that typically observed at the domain boundaries. The sizes of the crystals at the boundaries decrease with higher concentrations of La₂O₃, and the crystals (especially perrierite) within the domains become larger, resulting in a more homogeneous microstructure. This results in better dielectric properties, i.e., much higher quality factor for the sample with x = 0.4 in comparison to that with x = 0.1 after heat-treatment at 1150 or 1250 °C.     

Variable—Range hopping in Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>-K<Subscript>2</Subscript>B<Subscript>4</Subscript>O<Subscript>7</Subscript> glasses

The dc conductivity of the glasses in the Fe₂O₃-Bi₂O₃-K₂B₄O₇ system was studied at temperatures between 223 and 393 K. At temperatures from 300 to 223 K, T^–1/4 (T is temperature) dependence of the conductivity was found, however, both Mott variable-range hopping and Greaves intermediate range hopping models are found to be applicable. Mott and Greaves parameters analysis gave the density of states at Fermi level N (E_F) = 3.13 × 10²⁰–21.01 × 10²⁰ and 1.93 × 10²¹–16.39 × 10²¹ cm^–3eV^–1 at 240 K, respectively. The variable-range hopping conduction occurred in the temperature range T = 300–223 K, since W_D was found to be large (W_D = 0.08–0.14 eV for these glasses) and dominated the conduction at T < 300 K.     

Synthesis and study of structural,dielectric, magnetic and magnetoelectric properties of K<Subscript>0.5</Subscript>Na<Subscript>0.5</Subscript>NbO<Subscript>3</Subscript>–CoMn<Subscript>0.2</Subscript>Fe<Subscript>1.8</Subscript>O<Subscript>4</Subscript> composites

Magnetoelectric (ME) composites consisting of K_0.5Na_0.5NbO₃ (KNN) as ferroelectric phase and CoMn_0.2Fe_1.8O₄ (CMFO) as ferrite phase with general formula (x) CoMn_0.2Fe_1.8O₄–(1???x) K_0.5Na_0.5NbO₃ (x?=?10, 20, 30, 40 and 50 wt%) were synthesized using solid state reaction method. X-ray diffraction analysis asserts the existence of component phases including spinel phase of CMFO and orthorhombic phase of KNN. Field emission scanning electron microscopy has been used for studying the morphology and calculation of average grain size. The temperature dependent dielectric properties including dielectric constant (\(\varepsilon ^{\prime}\)) and dielectric loss (tan δ) at different frequencies has been studied and both are found to increase with incorporation of CMFO. Magnetic hysteresis loops have been measured at temperatures of 300 and 5 K. Variation of magnetization versus temperature has been studied in field cooled and zero field cooled modes. Polarization versus electric field (P–E) hysteresis loops are obtained at room temperature indicating presence of ferroelectric ordering in the composites at room temperature. The remnant polarization (2P_r) and coercive field (2E_c) are found to decrease linearly with incorporation of CMFO. ME voltage coefficient (α_ME) has been measured. The maximum value of α_ME is found to be 5.941 mV/cm-Oe for 10% CMFO–90% KNN bulk composite.     

Dielectric and piezoelectric properties of Bi<Subscript>0.5</Subscript>Na<Subscript>0.5</Subscript>TiO<Subscript>3</Subscript>–BaNb<Subscript>2</Subscript>O<Subscript>6</Subscript> lead-free piezoelectric ceramics

Lead-free piezoelectric ceramics (1 − x)Bi_0.5Na_0.5TiO₃–xBaNb₂O₆ (BNT–BN100x), a new member of the BNT-based group, was prepared by conventional solid state reaction. X-ray diffraction showed that BaNb₂O₆ (BN) diffused into the lattice of Bi_0.5Na_0.5TiO₃ to form a solid solution with perovskite-type structure. The temperature dependence of dielectric constant ε_r revealed that the solid solution underwent two phase transitions from ferroelectric to anti-ferroelectric and anti-ferroelectric to paraelectric. Both the transition temperature T _d and T _m were shifted to lower with the increasing content of BaNb₂O₆. The temperature dependence of dielectric constant at different frequency revealed that the solid solution exhibited obviously dielectric relaxation characteristics. The sample with x = 0.6 mol% exhibited excellent electrical properties, piezoelectric constant d ₃₃ = 94 pC/N; electromechanical coupling factor k _p = 0.185. The results showed that BNT–BN100x ceramics were good candidates for use as lead-free piezoelectric ceramics.     

Synthesis and characterization of TiO<Subscript>2</Subscript>–NiO and TiO<Subscript>2</Subscript>–WO<Subscript>3</Subscript> nanocomposites

TiO₂–NiO and TiO₂–WO₃ nanocomposites were prepared by hydrothermal and surface modification methods. The samples were analyzed using X-ray diffraction, Scanning Electron Microscope images, Transmission Electron Microscope, Energy dispersive analysis, Zeta potential, Electrophoretic mobility and Photocatalysis activity measurement. XRD data sets of TiO₂–NiO, TiO₂–WO₃ powder nanocomposite have been studied for the inclusion of NiO, WO₃ on the anatase-rutile mixture phase of TiO₂ by Rietveld refinement. The cell parameters, phase fraction, the average grain size, strain and bond lengths between atoms of individual phases have been reported in the present work. Shifted positional co-ordinates of individual atoms in each phase have also been observed.     

Structure and properties of CaF<Subscript>2</Subscript>–B<Subscript>2</Subscript>O<Subscript>3</Subscript> glasses

FTIR spectroscopy has been employed to investigate the structure of CaF₂–B₂O₃ glasses. It is proposed that CaF₂ partially modifies the borate network forming \textCa _{1 / 2} ²⁺ [\textBO _{3 / 2} \textF] ^- {\text{Ca}}_{ 1 / 2}^{ 2+ } [{\text{BO}}_{ 3 / 2} {\text{F]}}^{ - } units. The rest of CaF₂ is assumed to build an amorphous network formed of CaF₄ tetrahedra. Analysis of density and molar volume revealed that the volume of CaF₄ tetrahedron in the studied glasses is slightly greater than that in the crystalline form. Data of density, molar volume, and electric conductivity have been correlated with the glass structure. As far as the authors know, CaF₂–B₂O₃ glasses are investigated for the first time.     

Kinetics of Thermal Transformation of Mg<Subscript>3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript> · 8H<Subscript>2</Subscript>O to Mg<Subscript>3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript>

The kinetics of thermal dehydration of Mg₃(PO₄)₂ · 8H₂O was investigated using thermogravimetry at four different heating rates. The activation energies of the dehydration step of Mg₃(PO₄)₂ · 8H₂O were calculated through the isoconversional Ozawa and Kissinger-Akahira-Sunose (KAS) methods and iterative methods, which were found to be consistent and indicate a single mechanism. The possible conversion function of the dehydration reaction for Mg₃(PO₄)₂ · 8H₂O has been estimated through the Coats and Redfern integral equation, and a better kinetic model such as random nucleation of the “Avrami–Erofeev equation (A _3/2 model)” was found. The thermodynamic functions (ΔH*, ΔG*, and ΔS*) of the dehydration reaction are calculated by the activated complex theory and indicate that it is a non-spontaneous process when the introduction of heat is not connected.     

Synthesis and piezoelectric properties of (Na<Subscript>0.5</Subscript>Bi<Subscript>0.5</Subscript>)<Subscript>0.94</Subscript>Ba<Subscript>0.06</Subscript>TiO<Subscript>3</Subscript> ceramics prepared by sol–gel auto-combustion method

In this study, NaNO₃, Bi(NO₃)₃·5H₂O, Ba(NO₃)₂, Ti(OC₄H₉)₄ and citric acid were successfully introduced to fabricate lead-free piezoelectric (Na_0.5Bi_0.5)_0.94Ba_0.06TiO₃ [NBBT] nanopartical powders by a novel modified sol–gel auto-combustion method. The resultant products were characterized by the X-ray diffraction analysis and transmission electron microscope method. (Na_0.5Bi_0.5)_0.94Ba_0.06TiO₃ + Mn(NO₃)₂ [NBBTM] can be sintered by the traditional solid-state reaction, and the effects of NBBT doped different amounts of Mn(NO₃)₂ at various sintering temperatures upon phase formation, microstructure as well as piezoelectric properties were further studied. The experimental results show that it was helpful to control their chemical ingredients and microstructure to prepare nanocrystalline single phase NBBT powders. Where is the X-ray diffraction result of the corresponding ceramics to prove the existence of the mixing between rhombohedral and tetragonal phases at the MPB compositions. Doping 0.015 mol% Mn(NO₃)₂ into NBBT at 1,090 °C, piezoelectric constant (d ₃₃) and relative dielectric constant (ε_r) reach the superior value of 159pC/N and 1,304, respectively, and dielectric loss (tan δ) and electromechanical coupling factor (K _t) are 2.5% and 65%, respectively.     

Preparation and properties of Bi<Subscript>6</Subscript>Ti<Subscript>5</Subscript>WO<Subscript>22</Subscript>: a new phase in the Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>–TiO<Subscript>2</Subscript>–WO<Subscript>3</Subscript> system

In a recent report, the evaluation of the phase relations in the Bi₂O₃–TiO₂–WO₃ ternary system has shown the existence of a new phase with nominal composition close to Bi₆Ti₅WO₂₂. In the present contribution we attempt to prepare this single phase by using a solid state route. Although XRD analyses also show traces of two minority Aurivillius-type phases in the synthesized materials, the crystal structure of the Bi₆Ti₅WO₂₂ phase has been determined by Rietveld analyses revealing a complex structure similar to that of Bi₃(AlSb₂)O₁₁ and PbHoAl₃O₈ related compounds. The electrical response of this new phase was characterized as well. Three peaks are observed in its dielectric response: two of them positioned around 0 °C and can be assigned to this Bi₆Ti₅WO₂₂ structure. The third one rises up to 665 °C and confirms the presence of the Aurivillius-type phases.