Single‐Pot Ethane Carboxylation Catalyzed by New Oxorhenium(V) Complexes with N,O Ligands

The oxorhenium(V) chelates [ReOCl(N,O‐L)(PPh₃)] [N,O‐L=(OCH₂CH₂)N(CH₂CH₂OH)(CH₂COO) ( 2 ), (OCH₂CH₂)N(CH₂COO)(CH₂COOCH₃) ( 3 )] and [ReOCl₂(N,O‐L)(PPh₃)] [N,O‐L=C₅H₄N(COO‐2) ( 4 ) C₅H₃N(COOCH₃‐2)(COO‐6) ( 5 )] have been prepared by reaction of [ReOCl₃(PPh₃)₂] ( 1 ), in refluxing methanol, with N,N‐bis(2‐hydroxyethyl)glycine [bicine; N(CH₂CH₂OH)₂(CH₂COOH)], N‐(2‐hydroxyethyl)iminodiacetic acid [N(CH₂CH₂OH)(CH₂COOH)₂], picolinic acid [NC₅H₄(COOH‐2)] or 2,6‐pyridinedicarboxylic acid [NC₅H₃(COOH‐2,6)₂], respectively, with ligand esterification in the cases of 3 and 5 . All these complexes have been characterized by IR and multinuclear NMR spectroscopy, FAB⁺‐MS, elemental and X‐ray diffraction structural analyses. They act as catalysts, in a single‐pot process, for the carboxylation of ethane by CO, in the presence of potassium peroxodisulfate K₂S₂O₈, in trifluoroacetic acid (TFA), to give propionic and acetic acids, in a remarkable yield (up to ca. 30%) and under relatively mild conditions, with some advantages over the industrial processes. The picolinate complex 4 provides the most active catalyst and the carboxylation also occurs, although much less efficiently, by the TFA solvent in the absence of CO. The selectivity can be controlled by the ethane and CO pressures, propionic acid being the dominant product for pressures about ca. 7 and 4 atm, respectively (catalyst 4 ), whereas lower pressures lead mainly to acetic acid in lower yields. These reactions constitute an unprecedented use of Re complexes as catalysts in alkane functionalization.     

Synthesis and Characterization of Glucosamide Surfactant

The synthesis and structural analysis of glucosamide surfactants of the general formula C_nH_2n+1NH(CH₂)₂NHCO(CHOH)₄CH₂OH (n = 8, 10, 12) are described, and the surface activity properties of the surfactants are studied. N‐alkylethylenediamines were synthesized by the alkylation of the ethylenediamine with alkyl bromide. The glucosamide surfactants, N‐alkyl‐N′‐glucosylethylenediamine (C_nGA), were prepared by amidation of the precursor diamine with d ‐gluconic acid δ‐lactone. They were structurally characterized by IR, ¹H NMR and MS. They reduced the surface tension of water to approximately 26–27 mN m^?1 at concentration levels of (0.5–1.6) × 10^?3 mol L^?1.     

Combination of allyl protection and HYCRAMTM-linker technology for the synthesis of peptides with problematical amino acids and sequences

Analogues of both the nonapeptides, bradykinin and bradykinin potentiating nonapeptide BPP_9α, were synthesized using HYCRAM^TM-technique. The bradykinin analogues were assembled by the Boc-, Ddz- and Fmoc-strategy starting with Boc-Arg(Aloc)₂-OCr–OH, Ddz-Arg(Mtr)-OCr–OH and Fmoc–Arg(Mtr)-OCr–OH. While Boc- and Ddz-strategy provide peptides in good yield and purity, the Fmoc-strategy leads to a loss of peptide from resin. For simultaneous cleavage from HYCRAM^TM-resin and removal of Aloc-side chain protection optimized conditions for catalytic cleavage with Pd° were developed. As shown by the synthesis of BPP_9αanalogues the HYCRAM^TM-linker and the chlorotrityl resin allow the assembly of peptides with the C-terminal sequence Pro-Pro by preventing dioxopiperazine formation. Since the BPP_9α sequence contains the tripeptide Trp-X-Arg an intramolecular migration of the N^G-protecting group to the indole ring under conditions used for its removal had to be avoided. By the use of HYCRAM^TM-linker in combination with Aloc protection for the guanidino group and Ddz for N^αno modification of Trp occurred. HYCRAM^TM-technology in combination with Boc-, Ddz- or Aloc/All-protecting groups facilitates the synthesis of peptides with such very labile amino acids like cis-4-hydroxyproline.     

Synthesis,Surface and Antimicrobial Activities of Novel Cationic Gemini Surfactants

A series of novel cationic gemini surfactants [C_nH_2n+1–O–CH₂–CH(OH)–CH₂–N⁺(CH₃)₂–(CH₂)₂]₂·2Br^? [ 3a (n = 12), 3b (n = 14) and 3c (n = 16)] having a 2‐hydroxy‐1,3‐oxypropylene group [?CH₂–CH(OH)–CH₂–O–] in the hydrophobic chain have been synthesized and characterized. Their water solubility, surface activity, foaming properties, and antibacterial activity have been examined. The critical micelle concentration (CMC) values of the novel cationic gemini surfactants are one to two orders of magnitude smaller than those of the corresponding monomeric surfactants. Furthermore, the novel cationic gemini surfactants have better water solubility and surface activity than the comparable [C_nH_2n+1–N⁺(CH₃)₂–(CH₂)₂]₂·2Br^? (n‐4‐n) geminis. The novel cationic gemini surfactants 3a and 3b also exhibit good foaming properties and show good antibacterial and antifungal activities.     

Fully Enzymatic Resolution of Chiral Amines: Acylation and Deacylation in the Presence of Candida antarctica Lipase B

A fully enzymatic methodology for the resolution of chiral amines has been demonstrated. Candida antarctica lipase B (CaLB)‐catalyzed acylation with N‐methyl‐ and N‐phenylglycine, as well as analogues having the general formula R¹ X CH₂CO₂R² (R¹=Me, Ph; X=O, S) afforded the corresponding enantioenriched amides, which were subsequently enzymatically hydrolyzed. Surprisingly, CaLB also proved to be the catalyst of choice for this latter step. The heteroatom in the acyl donor profoundly influences both the enzymatic acylation and deacylation; the O‐substituted reagents performed best with regard to enantioselectivity as well as reaction rate in synthesis and hydrolysis.     

Effect of primary polymer chain rigidity on intramolecular cyclization and intramolecular crosslinking in free‐radical crosslinking monomethacrylate/dimethacrylate copolymerizations

d‐Bornyl methacrylate (BoMA) was chosen as a typical example of bulky monomethacrylate monomers, the polymerization of which led to the formation of a rigid polymer chain. To discuss the effect of primary polymer chain rigidity on intramolecular cyclization, we compared the solution copolymerization results of BoMA with 1 mol % ethylene dimethacrylate (EDMA; n = 1) and poly(ethylene glycol dimethacrylate) [CH₂?C(CH₃)CO(OCH₂CH₂)_nOCOC(CH₃)?CH₂, n = 9 (PEGDMA‐9)] with those of methyl methacrylate (MMA) with 1 mol % EDMA and PEGDMA‐9; the dependence of the weight‐average degree of polymerization on conversion for the former BoMA copolymerization systems was completely opposed to that for the latter MMA systems, and this was a reflection of a reduced occurrence of intramolecular cyclization caused by the rigidity of the primary polymer chain. The effect of primary polymer chain rigidity on intramolecular crosslinking was discussed through a comparison of both BoMA/EDMA and MMA/EDMA copolymerizations. The correlations of the intrinsic viscosity, root‐mean‐square (rms) radius of gyration, and second virial coefficient with the molecular weight were examined for both BoMA/EDMA (90/10) and MMA/EDMA (90/10) copolymerizations in a dilute solution because microgelation was observed in solution MMA/EDMA (90/10) copolymerization as a reflection of a locally extensive occurrence of intramolecular crosslinking. The logarithmic plots of both the intrinsic viscosity and rms radius of gyration versus the molecular weight for MMA/EDMA copolymerization were compared with those for the corresponding BoMA/EDMA copolymerizations. The second virial coefficients were greater than 10^?5 mol cm³ g^?2 for BoMA/EDMA copolymers, even when the conversion was very close to the gel point, whereas they were quite low, that is, less than 10^?5 mol cm³ g^?2, for an MMA/EDMA copolymer obtained at more than 15% conversion. These were ascribed to a suppressed occurrence of intramolecular crosslinking, a reflection of the lessened flexibility of the polymer main chain and a steric effect due to the bulky d‐bornyl groups. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1086–1093, 2004     

Supramolecular structure of the tetrabutylammonium salt of 2-phenylpropionitrile

The deprotonation of 2-phenylpropionitrile Ph(CH₃)CHCN ( 3 ) by n-Bu)₄N⁺(OH)^– results in the corresponding tetrabutylammonium salt ( 4 ) in excellent yield. An X-ray structural analysis shows that the compound is not a genuine carbanion (“naked anion”). Instead, a dimeric form is found in the crystal in which the nitrogen of the cyano group in the anion undergoes multiple H-bonding with the α-methylene units of the (n-Bu)₄N⁺ cations as a consequence of CH…︁N interactions. A cryoscopic study of the compound in benzene indicates the existence of tetramers, which means that in solution supramolecular ions pairs are involved.     

Detection of end-groups and estimation of molecular weights of polyiminoalkenes by 13C n.m.r. spectroscopy

Linear polyiminoalkenes R²-[NHCHR¹CH₂]-_nX, (R¹ = H, CH₃, C₂H₅), were prepared by alkaline hydrolysis of the N-formyl precursors, which had been obtained by the polymerization of oxazoline, 4-methyloxazoline and 4-ethyloxazoline, respectively, using methyl iodide, ethyl iodide or dimethyl sulphate as initiator. When the initiator concentration was 5–20 mol % of the initial monomer concentration, the ¹³C n.m.r. spectra showed minor peaks which could be assigned to carbon atoms in the two end units, R² being CH₃ or C₂H₅ according to the initiator, and X being OH. This confirms the mechanism in which the attack on the oxazoline molecule occurs at the nitrogen atom, with subsequent opening of the OCH₂ bond. For R¹ = C₂H₅ the end-group X was successfully converted to Cl by reaction with thionyl chloride.Values of n determined by v.p.o. were in the range 5–20 and similar values were obtained from ¹³C n.m.r. peak intensities using the ratio of the average main peak intensity to the average end-group peak intensity. A correlation was also noted with the ratio of the initial monomer and initiator concentrations; after allowance for yield an initiator efficiency of the order of 50–100% may be deduced.     

Peptide Synthesis at High Pressure: Activation volume of a peptide coupling,synthesis of a glutathione derivative

From the pressure-induced rate enhancement the activation volume of the peptide coupling 1 with the sodium salt of glycine 2 leading to the corresponding dipeptide derivative 3 was determined to be strongly negative (ΔV^≠ = −(19.3 ± 0.5) cm³mol⁻¹ at 51.7 °C, CH₃OH). This finding indicates that and association with the developing of charge proceeds in the rate-determining transition state. The pressure-induced peptide coupling was exploited to synthesize a derivative ( 12a, b ) of glutathione (γ-Glu-Cys-Gly), a biologically important tripeptide, starting from either glycine or glutamic acid.     

Diruthenium(I,I) Catalysts for the Formation of β‐ and γ‐Lactams via Carbenoid C?H Insertion of α‐Diazoacetamides

Intramolecular carbenoid C H insertion of five α‐diazoacetamides [N₂CH CONR₂, NR₂=NEt₂ ( 3a ), NBu₂ ( 3b ), N(i‐Pr)₂ ( 3c ), N(CH₂Ph)₂ ( 3d ), N(i‐Pr)(CH₂Ph) ( 3e )], was investigated using as catalysts dinuclear Ru(I,I) complexes of the type [Ru₂(μ‐L¹)₂(CO)₄L²₂], where L¹ is a bidentate bridging acetate, calix[4]arenedicarboxylate, saccharinate, pyridin‐2‐olate, or triazenide ligand, as well as [RuCl₂(p‐cymene)]₂. The Ru(I,I) complexes were found to be suitable catalysts for the carbenoid cyclization reactions, except in the case of 3a . With diazoamides 3b–e , [Ru₂(μ‐sac)₂(CO)₅]₂ (sac=saccharinate) and [Ru₂(μ‐6‐chloropyridin‐2‐olate)₂(CH₃CN)₂(CO)₄] are as effective as Rh₂(OAc)₄ under the same conditions, although some differences in the regioselectivity and chemoselectivity of the cyclization are observed. The carbenoid cyclization reactions yield γ‐lactams from diazoamides 3a and 3b , both a β‐ and a γ‐lactam from 3c , and a β‐lactam as well as a 3‐azabicyclo[5.3.0]deca‐5,7,9‐trien‐2‐one from 3d . With 3e , formation of γ‐lactam 21 and of bicyclic lactam 23 prevails.     

Polymer electrolyte complexes of LiCIO4 and comb polymers of siloxane with oligo-oxyethylene side chains

Polysiloxanes with oligo-oxyethylene side chains of the type —O(CH₂CH₂O)₇CH₃ and —(CH₂)₃O(CH₂CH₂O)_nCH₃ (average n ≈ 7 and 11) were synthesized from poly(hydrogenmethylsiloxane) and characterized by ¹H n.m.r., ²⁹Si n.m.r., i.r. and g.p.c. Cyclic analogues were used as model compounds and synthesized from tetramethylcyclotetrasiloxane. Polymer electrolyte complexes were made from the comb polymers and LiClO₄ by solvent-casting from THF, and their conductivities measured as a function of temperature and studied by differential scanning calorimetry and correlated with their conductivity behaviour. Maximum conductivities close to 10^?4S cm^?1 were achieved at room temperature and at ethylene oxide units to Li⁺ ratios of about 25. Cross-linking or blending with high molecular weight poly(oxyethylene) lowers the conductance somewhat but vastly improves the mechanical properties of the complexes, and the blends with PEO can be cast into thin, flexible and tough films with good conducting properties.     

Ionic polymers with expanded π‐conjugation systems derived from through‐space interaction in piperazinium and homopiperazinium rings

Reactions of N‐(2,4‐dinitrophenyl)‐4‐arylpyridinium chlorides (aryl (Ar) = phenyl and 4‐biphenyl) with piperazine or homopiperazine caused opening of the pyridinium ring and yielded polymers that consisted of 5‐piperazinium‐3‐arylpenta‐2,4‐dienylideneammonium chloride (? N(CH₂CH₂)₂N⁺ (Cl^?)?CH? CH?C(Ar)? CH?CH? ) or 5‐homopiperazinium‐3‐arylpenta‐2,4‐dienylideneammonium chloride (? N(CH₂CH₂CH₂)(CH₂CH₂)N⁺ (Cl^?)?CH? CH?C(Ar)? CH?CH? ) units. ¹H NMR spectral analysis suggested that the π‐electrons of the penta‐2,4‐dienylideneammonium group of the polymers were delocalized. UV‐visible spectral measurements revealed that the π‐conjugation system expanded along the polymer chains because of the orbital interaction between electrons of the two nitrogen atoms of the piperazinium and homopiperazinium rings. However, the π‐conjugation length depended on the distance between the two nitrogen atoms; that is, the polymers containing the piperazinium ring had a longer π‐conjugation length than those containing the homopiperazinium ring. Conversion of the piperazinium and homopiperazinium rings from the boat to the chair form led to a decrease in the π‐conjugation length. The surface of pellets that were molded from the polymers exhibited metallic luster, and these polymers underwent electrochemical oxidation in solution. Copyright © 2010 Society of Chemical Industry     

Magnetic behavior of polycarbosilazane ?FeII, ?FeIII and mixed‐valence ?FeII–III chloride metallopolymers

Fe^II, Fe^III and mixed‐valence Fe^II–III chlorides were reacted with poly[N,N′‐bis(dimethylsilyl)ethylenedi‐ amine], [? Si(CH₃)₂NHCH₂CH₂NH? ]_n, to form the corresponding Fe‐polycarbosilazane macromolecular complexes. The average chain–chain spacing in these materials was estimated from X‐ray diffraction data and found to be 6.94, 7.29, 7.30 and 7.45 Å in metal‐free and Fe^II? , Fe^III? and Fe^II–III‐containing polycarbosilazanes, respectively. This demonstrates that Fe^II, Fe^III and Fe^II–III chlorides are encapsulated between the polycarbosilazane chains. The chain–chain expansions in the divalent Fe^II and trivalent Fe^III chloride macromolecular complexes are comparable, but less than that in the Fe^II–III chloride analog, which suggests that different chain–chain packings exist in the mixed‐valence macromolecular complex. The magnetic properties of the resulting complexes were investigated by measuring the magnetization in magnetic fields up to 8 kOe and in the temperature range from liquid nitrogen temperature to room temperature. Copyright © 2007 Society of Chemical Industry     

Vinyl ether‐based polyacetal polyols with various main‐chain structures and polyurethane elastomers prepared therefrom: Synthesis,structure, and functional properties

Novel acid degradable polyacetal polyols and polyacetal polyurethanes able to controlled acid degradation were developed. Polyacetal polyols with various main‐chain structures were synthesized by polyaddition of various vinyl ethers with a hydroxyl group [4‐hydroxy butyl vinyl ether (CH₂?CH? O? CH₂CH₂CH₂CH₂? OH), 2‐hydroxy ethyl vinyl ether (CH₂?CH? O? CH₂CH₂? OH), diethylene glycol monovinyl ether (CH₂?CH? O? CH₂CH₂OCH₂CH₂? OH), and cyclohexanedimethanol monovinyl ether (CH₂?CH? O? CH₂? C₆H₁₀? CH₂? OH)] with p‐toluenesulfonic acid monohydrate (TSAM) as a catalyst in the presence of the corresponding diols [1,4‐butandiol (HO? CH₂CH₂CH₂CH₂? OH), ethylene glycol (HO? CH₂CH₂? OH), diethylene glycol (HO? CH₂CH₂OCH₂CH₂? OH), and 1,4‐cyclohexanedimethanol (HO? CH₂? C₆H₁₀? CH₂? OH)], respectively. Polyacetal polyurethanes were prepared by a two‐step polymerization, using the synthesized polyacetal polyols, 4,4′‐diphenylmethane diisocyanate (MDI), and 1,4‐butandiol (BD) as a chain extender. Depending on the main‐chain structures, these polyurethanes had different glass transition temperature (from ?44 to 19 °C) and properties such as hydrophobic or hydrophilic. Polyurethanes containing the hydrophilic main‐chain exhibited the thermoresponsiveness and had the certain volume phase transition temperature (VPTT). The polyacetal polyurethanes were flexible elastomers around room temperature (～25 °C) and thermally stable (T_d ≥ 310 °C) and additionally exhibited smooth degradation with a treatment of aqueous acid in THF at room temperature to give the corresponding raw material diols. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44088.     

Efficient synthesis of organic carbonates and poly(1,4‐butylene carbonate‐co‐terephthalate)s

Dimethyl carbonate (DMC) is an environmentally benign chemical currently produced using CO₂. Using the conventional Dean–Stark apparatus, a method was developed for the effective and selective removal of the methanol generated in the transesterification of DMC with alcohol. Using this device, various diols (HO‐A‐OH; A = (CH₂)₄, (CH₂)₂O(CH₂)₂, CH₂C₆H₁₀CH₂, and CH₂C₆H₄CH₂) were converted to mixtures of the corresponding MeOC(O)[O‐A‐OC(O)]OMe and MeOC(O)[O‐A‐OC(O)]₂OMe. Dialkyl carbonates such as dibutyl carbonate, dibenzyl carbonate, and diallyl carbonate were also efficiently prepared from the corresponding alcohols using this device. The compound prepared from 1,4‐butanediol, MeOC(O)[O(CH₂)₄OC(O)]_1.5OMe, was subjected to polycondensation with HO(CH₂)₄[O₂CC₆H₄CO₂(CH₂)₄]_1.5OH or HO(CH₂)₄[O₂CC₆H₄CO₂(CH₂)₄]_1.8OH, which directly was prepared from terephthalic acid and 1,4‐butanediol. The polycondensation afforded high‐molecular‐weight poly(1,4‐butylene carbonate‐co‐terephthalate)s (PBCTs) with M_w of 80–270 kDa and 0.40–0.46 terephthalate mole fractions. PBCTs are attractive materials with potential biodegradability and LDPE‐like thermal properties. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44951.     

Nickel(II) complexes bearing the bis(β‐ketoamino) ligand for the copolymerization of norbornene with a higher 1‐alkene

A novel bis(β‐ketoamino)Ni(II) complex catalyst, Ni{CF₃C(O)CHC[N(naphthyl)]CH₃}₂, was synthesized, and the structure was solved by a single‐crystal X‐ray refraction technique. The copolymerization of norbornene with higher 1‐alkene was carried out in toluene with catalytic systems based on nickel(II) complexes, Ni{RC(O)CHC[N(naphthyl)]CH₃}₂(R?CH₃, CF₃) and B(C₆F₅)₃, and high activity was exhibited by both catalytic systems. The effects of the catalyst structure and comonomer feed content on the polymerization activity and the incorporation rates were investigated. The reactivity ratios were determined to be r_1‐octene = 0.009 and r_norbornene = 13.461 by the Kelen–Tüdõs method for the Ni{CH₃C(O)CHC[N(naphthyl)]CH₃}₂/B(C₆F₅)₃ system. The achieved copolymers were confirmed to be vinyl‐addition copolymers through the analysis of ¹H‐NMR and ¹³C‐NMR. The thermogravimetric analysis results showed that the copolymers exhibited good thermal stability (decomposition temperature, T_dec > 400°C), and the glass‐transition temperature of the copolymers were observed between 215 and 275°C. The copolymers were confirmed to be noncrystalline by wide‐angle X‐ray diffraction analysis and showed good solubility in common organic solvents. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Inhibition of polyketone oxidation

Oxidation of polyketones [poly(ethylene ketone) (? CH₂? CH₂? CO‐)_n and poly(propylene ketone) (? CH₂? CH(CH₃)? CO‐)_n] in the presence of antioxidant [2,2′‐methylene‐bis(4‐methyl‐6‐tert‐butylphenol)] was studied in the temperature range 120–190°C. The effectiveness of the antioxidant in polyketones is much lower than that in polyolefins. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1182–1185, 2003     

Effects of amines on the polymerization of isoprene with sec-butyllithium catalyst

Polymerization of isoprene (IP) with alkyllithium (RLi) catalysts in the presence of amines such as triethylamine (TEA), 1,2-dipiperidinoethane (DPPE) and N,N,N′,N′-tetramethyldiaminoalkanes [(CH₃)₂N(CH₂)_nN(CH₃)₂ where n=1, 2, 3, 4 and 6 (TMDAA)] has been studied. By adding the amines, the polymerization rate of IP was accelerated, and the contents of 3,4- and 1,2-units in the resulting polymers increased. The effects of methylene chain length of the TMDAA on the polymerization were examined. It was found that both the polymerization rates and the microstructure of the polymers depend on the methylene length of the TMDAA. The amines having 2 and 3 methylenes in (CH₃)₂N(CH₂)_nN(CH₃)₂ favoured production of the polymer consisting of predominantly 1,2- and 3,4-units. It was proposed that two types of active sites for the polymerization of IP were produced depending on the number n of the TMDAA. Two types of active species were confirmed to be produced with sec-BuLi in the presence of N,N,N′,N′-tetramethylethylenediamine (TMEDA) depending on the TMEDA/sec-BuLi mole ratios. © 1998 SCI.     

Improved Synthesis and X‐Ray Structure of 5‐Aminotetrazolium Nitrate

5‐Aminotetrazolium nitrate was synthesized in high yield and characterized using Raman and multinuclear NMR spectroscopy (¹H, ¹³C, ¹⁵N). The molecular structure of 5‐aminotetrazolium nitrate in the crystalline state was determined by X‐ray crystallography: monoclinic, P 2₁/c, a=1.05493(8) nm, b=0.34556(4) nm, c=1.4606(1) nm, β=90.548(9)°, V=0.53244(8) nm³, Z=4, ϱ=1.847 g cm⁻³, R₁=0.034, wR₂ (all data)=0.090. The thermal stability of 5‐aminotetrazolium nitrate was determined using differential scanning calorimetry; the compound decomposes at 167 °C. The enthalpy of combustion (Δ_combH) of 5‐aminotetrazolium nitrate ([CH₄N₅]⁺[NO₃]⁻) was determined experimentally using oxygen bomb calorimetry: Δ_combH([CH₄N₅]⁺[NO₃]⁻)=−6020±200 kJ kg⁻¹. The standard enthalpy of formation (Δ_fH°) of [CH₄N₅]⁺[NO₃]⁻ was obtained on the basis of quantum chemical computations at the electron‐correlated ab initio MP2 (second order Møller‐Plesset perturbation theory) level of theory using a correlation consistent double‐zeta basis set (cc‐pVTZ): Δ_fH°([CH₄N₅]⁺[NO₃]⁻(s))=+87 kJ mol⁻¹=+586 kJ kg⁻¹. The detonation velocity (D) and the detonation pressure (P) of 5‐aminotetrazolium nitrate were calculated using the empirical equations by Kamlet and Jacobs: D([CH₄N₅]⁺[NO₃]⁻)=8.90 mm μs⁻¹ and P([CH₄N₅]⁺[NO₃]⁻)=35.7 GPa.     

Effect of chemically modified clinoptilolite on the thermal,morphological, and gas separation properties of mixed matrix membranes

Mixed matrix membranes (MMM) based on polysulfone and chemically modified clinoptilolite were prepared. Clinoptilolite enriched with Ca²⁺, K⁺, and Na⁺ by ion exchange at two test temperatures was prepared. Chemical composition was monitored by energy dispersive X‐ray spectroscopy. X‐ray diffraction, thermogravimetric analysis, and N₂ adsorption–desorption isotherms were also performed. Thermal and morphological properties of MMM were evaluated. CH₄/CO₂ gas mixture permeability tests at different upstream pressure were carried out. Type of exchanged cation in modified clinoptilolite affected the CO₂ permeability. An improvement on the CO₂/CH₄ selectivity values in the MMM compared to the polymeric membrane was appreciated. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45659.