Electromagnetic interference shielding mechanisms of CNT/polymer composites

The electromagnetic interference (EMI) shielding mechanisms of multi-walled carbon nanotube (MWCNT)/polymer composites were analyzed experimentally and theoretically. For the experimental analysis, EMI shielding effectiveness (SE) of MWCNT/polypropylene (PP) composite plates made in three different thicknesses and at four different concentrations were studied. A model based on the shielding of electromagnetic plane wave was used to theoretically study the EMI shielding mechanisms. The experimental results showed that absorption is the major shielding mechanism and reflection is the secondary shielding mechanism. The modeling results demonstrated that multiple-reflection within MWCNT internal surfaces and between MWCNT external surfaces decrease the overall EMI SE. The EMI SE of MWCNT/PP composites increased with increase in MWCNT content and shielding plate thickness.     

Effects of hybrid fillers on the electrical conductivity,EMI shielding effectiveness,and flame retardancy of PBT and PolyASA composites with carbon fiber and MWCNT

The effects of hybrid fillers of carbon fiber (CF) and multiwall carbon nanotube (MWCNT) on the electrical conductivity, electromagnetic interference shielding effectiveness (EMI SE), flame retardancy, and mechanical properties of poly(butylene terephthalate) (PBT)/poly(acrylonitrile-co-styrene-co-acrylate) (PolyASA) (70/30, wt %) with conductive filler composites were investigated. The CF was used as the main filler, and MWCNT was used as the secondary filler to investigate the hybrid filler effect. For the PBT/PolyASA/CF (8 vol %)/MWCNT (2 vol %) composite, a higher electrical conductivity (1.4 × 10⁰ S cm⁻¹) and EMI SE (33.7 dB) were observed than that of the composite prepared with the single filler of CF (10 vol %), which were 9.0 × 10⁻² S cm⁻¹ and 23.7 dB, respectively. This increase in the electrical properties might be due to the longer CF length and hybrid filler effect in the composites. From the results of aging test at 85 °C, 120 h, the electrical conductivity and EMI SE of the composites decreased slightly compared to that of the composite without aging. The results of electrical conductivity, EMI SE, and flame retardancy suggested that the composite with the hybrid fillers of CF and MWCNT showed a synergetic effect in the PBT/PolyASA/CF (8 vol %)/MWCNT (2 vol %) composite. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48162.     

High electromagnetic interference shielding with high electrical conductivity through selective dispersion of multiwall carbon nanotube in poly (ε‐caprolactone)/MWCNT composites

This study presents the preparation of electrically conducting poly(ε‐caprolactone) (PCL)/multiwall carbon nanotube (MWCNT) composites with very low percolation threshold (p_c). The method involves solution blending of PCL and MWCNT in the presence of commercial PCL beads. The PCL beads were added into high viscous PCL/MWCNT mixture during evaporation of solvent. Here, the used commercial PCL polymer beads act as an ‘excluded volume’ in the solution blended PCL/MWCNT region. Thus, the effective concentration of the MWCNT dramatically increases in the solution blended region and a strong interconnected continuous conductive network path of CNT−CNT is assumed throughout the matrix phase with the addition of PCL bead which plays a crucial role to improve the electromagnetic interference shielding effectiveness (EMI SE) and electrical conductivity at very low MWCNT loading. Thus, high EMI SE value (∼23.8 dB) was achieved at low MWCNT loading (1.8 wt %) in the presence of 70 wt % PCL bead and the high electrical conductivity of ∼2.49×10⁻² S cm⁻¹ was achieved at very low MWCNT loading (∼0.15 wt %) with 70 wt % PCL bead content in the composites. The electrical conductivity gradually increased with increasing the PCL bead concentration, as well as, MWCNT loading in the composites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42161.     

Electrical, morphological and rheological properties of carbon nanotube composites with polyethylene and poly(phenylene sulfide) by melt mixing

Electrical, morphological and rheological properties of polyethylene (PE)/multi-walled carbon nanotube (MWCNT) and poly(phenylene sulfide) (PPS)/MWCNT composites were studied with the MWCNT content using vector network analyzer, scanning electron microscopy and rotational rheometry. From the results of electrical conductivity and electromagnetic interference shielding efficiency (EMI SE) of the PE/MWCNT and PPS/MWCNT composites, the electrical percolation threshold of the composites has found to be 5 and 3 wt% MWCNT, respectively. From the results of the EMI SE of the composites, it was suggested that the increase in homogeneous dispersion of the MWCNT in the PPS matrix has been attributed to the increase in connectivity of the MWCNT-MWCNT network structure of the composite. Therefore, the higher values of the EMI SE with the MWCNT content were observed in the PPS/MWCNT than the PE/MWCNT composites. From the results of the rheological properties of the PE/MWCNT and PPS/MWCNT composites, the increase in the complex viscosity was observed for the PPS/MWCNT than the PE/MWCNT composites. The increase in complex viscosity maybe due to the increase in homogeneous dispersion of the MWCNT in the PPS matrix than that in the PE matrix. From the results of the rheological properties of the PE/MWCNT and PPS/MWCNT composites, it was suggested that the homogeneous dispersion of the MWCNT in the polymer matrix has affected the increase in complex viscosity of the PPS/MWCNT composite. This result of rheological behavior is consistent with the results of the EMI SE of the PE/MWCNT and PPS/MWCNT composites.     

Fabrication and characterization of NBR/MWCNT composites by latex technology

To develop a rubber composite with excellent electrical properties, a sort of synthetic rubber, acrylonitrile butadiene rubber (NBR) with CN dipoles as matrix, multi‐walled carbon nanotubes (MWCNTs) as filler, was synthesized. NBR composites reinforced with 0.5, 1.5, 3, 10, and 20 phr MWCNT contents were fabricated by latex technology. The electrical conductivity, dielectric characteristics, and electromagnetic interference (EMI) shielding effectiveness at room temperature of NBR/MWCNT composites were investigated. MWCNTs were found well dispersed into NBR matrix even for 20 phr content by FESEM observation. The electrical conductivity increased with an increment of MWCNT content. The dielectric constant was over 10⁴ at 10³ Hz frequency for 10 and 20 phr MWCNTs‐reinforced NBR composites. It was attributed to the increased electrons and interface polarization. The improved conductivity and dielectric permittivity resulted in an enhanced EMI shielding effectiveness. The EMI shielding effectiveness reached 26 dB at 16.7 GHz frequency for NBR/20 phr MWCNT composite with 1.0 mm thickness. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

ASA/graphite/carbon black composites with improved EMI SE,conductivity and heat resistance properties

Composites, comprised of acrylonitrile styrene acrylate copolymer (ASA)/graphite (GR) with high electromagnetic interference shielding effectiveness (EMI SE), were fabricated by the introduction of carbon black (CB). The effects of CB on properties such as EMI SE, morphology, heat resistance, rheological and mechanical performance of the composites were characterized using a scanning electron microscope (SEM), rotational rheometer, electromagnetic shielding measuring instruments. The graphite and carbon black exhibited positive synergistic action, which promoted the complete formation of conductive networks in ASA matrix. The EMI SE and electrical conductivity of the ASA/GR/CB composites increased with higher CB loadings. In the frequency range of 30–3000 MHz, the maximum EMI SE of ASA composites with 50 % fillers reached 40 dB, but with 40 % fillers this property reached its maximum value of 50 dB. The flexural strength of ASA/GR/CB composites started to decline as CB loading exceeded 5 %. The heat resistance of the composites was improved due to the addition of CB. In this respect, the vicar softening temperature (VST) of the composites with 40 % fillers increased from 115.1 to 132.7 °C, and the VST of the composites with 50 % fillers was elevated from 125.4 to 138.9 °C.     

Dynamic mechanical characterization of PC/MWCNT composites under variable temperature conditions

A dynamic mechanical analysis has been performed on composite materials of polycarbonates (PC) and multi-walled carbon nanotubes (MWCNT) for evaluation of their mechanical hardness and storage modulus under the combined effects of variable loading frequencies and temperature conditions. The PC-based engineering machine components that are subjected to variable external loads and temperature conditions are not durable owing to the viscoelastic properties of PC. Composites of PC with MWCNT (2, 5 and 10 wt%) were fabricated and their mechanical characterization tests revealed that with increase in MWCNT composition both storage modulus and hardness enhanced significantly in comparison to pure PC. For 10 wt% PC/MWCNT composite, the average storage modulus increased in the range of 40–92%, while the average hardness was enhanced in a range of 88–121% for the combined effect of temperature range of 30–90 °C and loading frequency range of 30–230 Hz. With increase in temperature, the maxima of storage moduli and hardness for these composites shifted toward higher loading frequencies, indicating that these composites can be used for wider loading frequency range. Therefore, the experimental results of this paper have shown that the mechanical properties of PC-based composite materials with minor MWCNT compositions are enhanced significantly and hence can be used for automotive and aerospace engine parts where loading frequencies are high and temperature conditions are variable.     

Electrical conductivity and EMI shielding effectiveness of polyurethane foam–conductive filler composites

The morphological, electrical, and thermal properties of polyurethane foam (PUF)/single conductive filler composites and PUF/hybrid conductive filler composites were investigated. For the PUF/single conductive filler composites, the PUF/nickel‐coated carbon fiber (NCCF) composite showed higher electrical conductivity and electromagnetic interference shielding effectiveness (EMI SE) than did the PUF/multiwall carbon nanotube (MWCNT) and PUF/graphite composites; therefore, NCCF is the most effective filler among those tested in this study. For the PUF/hybrid conductive fillers PUF/NCCF (3.0 php)/MWCNT (3.0 php) composites, the values of electrical conductivity and EMI SE were determined to be 0.171 S/cm and 24.7 dB (decibel), respectively, which were the highest among the fillers investigated in this study. NCCF and MWCNT were the most effective primary and secondary fillers, and they had a synergistic effect on the electrical conductivity and EMI SE of the PUF/NCCF/MWCNT composites. From the results of thermal conductivity and cell size of the PUF/conductive filler composites, it is suggested that a reduction in cell size lowers the thermal conductivity of the PUF/conductive filler composites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44373.     

聚丙烯基复合材料的结晶行为

综述了3类聚丙烯(PP)基复合材料体系包括PP/无机物体系、PP/有机物体系和PP／聚合物体系的结晶行为。阐述了PP基体的结晶结构以及结晶动力学特征,包括添加物对PP的结晶温度、结晶速率及结晶度等的影响;分析了结晶行为对复合材料力学性能的影响。复合材料界面对基体聚合物取向结晶形态及结晶行为的影响等还需进一步研究。     

High‐performance EMI shielding materials based on short carbon fiber‐filled ethylene vinyl acetate copolymer,acrylonitrile butadiene copolymer,and their blends

The composites of carbon fiber with EVA, NBR, and their blends have been made by melt mixing technique. Stress–strain plots of different composites show that the necking phenomenon is increasing with the increase in fiber concentration in the polymer matrix. The scanning electron microscopic analysis and swelling study exhibit poor interaction between the short carbon fiber and polymer matrix. The decrease in DC resistivity with the increase in short carbon fiber concentration has been explained on the basis of percolation theory. EMI SE increases slightly with the increase in frequency of electromagnetic radiation but increases sharply with the increase in fiber concentration. EMI SE also depends on blend composition and increases with the increase in EVA concentration in the blend. Return loss is decreasing but absorption loss is increasing with the increase in fiber loading. A linear relationship is observed between the EMI SE and thickness of the composites. The EMI SE is found to increase exponentially with the increase in conductivity of the composite. The permeability value is decreasing with the increase in frequency as well as fiber loading. Thermal properties of the composites have been evaluated by thermogravimetric analysis and dynamic mechanical analysis. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Effects of interfacial adhesion on properties of polypropylene/Wollastonite composites

Wollastonite reinforced polypropylene (PP/CaSiO₃) composites were prepared by melt extrusion. A silane coupling agent and a maleic anhydride grafted PP (PP‐g‐MA) were used to increase the interfacial adhesion between the filler and the matrix. The increased adhesion observed by scanning electron microscopy (SEM) resulted in improved mechanical properties. A model was applied to describe the relationship between the interfacial adhesion and tensile properties of PP/CaSiO₃ composites. There is stronger interfacial adhesion between silane‐treated CaSiO₃ and polymer matrix containing PP‐g‐MA as a modifier. Results of dynamic mechanical thermal analysis (DMTA) showed that stronger interfacial adhesion led to higher storage modulus. The influence of CaSiO₃ particles on the crystallization of PP was studied by using differential scanning calorimetry (DSC). The introduction of CaSiO₃ particles does not affect the crystallization temperature and crystallinity of PP matrix significantly. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermoplastic polyvinyl alcohol/multiwalled carbon nanotube composites: Preparation,mechanical properties,thermal properties,and electromagnetic shielding effectiveness

This study uses the solution mixing method to combine plasticized polyvinyl alcohol (PVA) as a matrix, and multiwalled carbon nanotubes (MWCNTs) as reinforcement to form PVA/MWCNTs films. The films are then laminated and hot pressed to create PVA/MWCNTs composites. The control group of PVA/MWCNTs composites is made by incorporating the melt compounding method. Diverse properties of PVA/MWCNTs composites are then evaluated. For the experimental group, the incorporation of MWCNTs improves the glass transition temperature (T_g), crystallization temperature, T_c), and thermal stability of the composites. In addition, the test results indicate that composites containing 1.5 wt % of MWCNTs have the maximum tensile strength of 51.1 MPa, whereas composites containing 2 wt % MWCNTs have the optimal electrical conductivity of 2.4 S/cm, and electromagnetic shielding effectiveness (EMI SE) of ?31.41 dB. This study proves that the solution mixing method outperforms the melt compounding method in terms of mechanical properties, dispersion, melting and crystallization behaviors, thermal stability, and EMI SE. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43474.     

Noncovalent compatibilization of polypropylene/MWCNT composites using an amino‐pyridine grafted polypropylene matrix

Polypropylene (PP)/multiwalled carbon nanotube (MWCNT) composites are prepared by implementing noncovalent compatibilization. The compatibilization method involves PP matrix functionalization with pyridine (Py) aromatic moieties, which are capable of π–π interaction with MWCNT sidewalls. Imaging revealed that the addition of 25 wt% of PP‐g‐Py to neat PP is capable of drastically reducing nanotube aggregate size and amount, compared to a matrix containing the equivalent amount of a maleated PP (PP‐g‐MA). Raman spectroscopy confirms improved polymer/nanotube interaction with the PP‐g‐Py matrix. The electrical percolation threshold appears at a MWCNT loading of approximately 1.2 wt%, and the maximum value of the electrical conductivity achieved is 10⁻² S/m, irrespective of the functionalization procedure. The modulus of the composites is improved with the addition of MWCNTs. Furthermore, composites functionalized with Py display significant improvements in composite ductility compared with their maleated counterparts because of the improved filler dispersion. POLYM. COMPOS., 37:2794–2802, 2016. © 2015 Society of Plastics Engineers     

Morphological,mechanical, and electromagnetic interference shielding effectiveness characteristics of glass fiber/epoxy resin/MWCNT buckypaper composites

Glass fiber/epoxy resin composites (GF/EP) using one and three multi-walled carbon nanotube buckypapers (BP) were obtained and their complex parameters, reflectivity, and electromagnetic interference (EMI) shielding effectiveness (SE) at X-band (8.2–12.4 GHz) and Ku-band (12.4–18 GHz) were evaluated. The preparation of BP used polyacrylonitrile (PAN) nanofibers (PF These composites show both large storage and energy loss capacity in both bands revealing promising results related to EMI SE applications. Besides, a high attenuation of around 67% and 72% were achieved for BP based composites. The cross-section view of the buckypaper and the laminates was analyzed by scanning electron microscopy (SEM). The incorporation of the CNT film into the laminates showed no improvements in the elastic properties through dynamic mechanical analyses (DMA). Nevertheless, a decrease in the shear properties by the compression shear test (CST) and interlaminar shear strength (ILSS) has been observed. GF/EP/BP/PF composite presented a reduction of 29 and 39% in its ILSS properties compared to the base laminate (GF/EP). Also, the decrease was even more significant, revealing a steep reduction in its CST properties. On the other hand, the removal of the pan nanofiber (PF) led to better mechanical properties for GF/EP/BP/RPF composites. Results have shown ILSS values of 47.4 ± 2.2 MPa which are close to the base laminate (52.4 ± 3.1 MPa). The removal of the PF provided larger porous in the CNT network, making the impregnation by epoxy easier in the BP/RPF which resulted in improved shear properties compared to GF/EP/BP/PF samples.     

Synergistic effect of multiwalled carbon nanotubes and an intumescent flame retardant: Toward an ideal electromagnetic interference shielding material with excellent flame retardancy

To shield undesirable electromagnetic waves caused by electronic devices and simultaneously resolve the flame safety of the electronic components, an electromagnetic interference (EMI) shielding material with excellent flame‐retardant properties is urgently needed. The synergistic effect of the intumescent flame retardant (IFR) and multiwalled carbon nanotubes (MWCNTs) for polystyrene (PS) nanocomposites prepared by melt blending was investigated. The results show that addition of certain amounts of IFRs facilitated the dispersion of MWCNTs in the PS matrix, and the percolation threshold of the MWCNTs in the PS matrix also decreased from 1.67 ± 0.05 to 1.29 ± 0.04 wt %. Moreover, the EMI shielding efficiencies (SEs) of the PS–MWCNT–IFR composites were consistently higher than those of the PS–MWCNT composites without the addition of the IFRs at the same MWCNT content; this indicated that the synergistic effect of the MWCNTs and IFRs effectively improved the EMI SE of the PS–MWCNT–IFR composites. Furthermore, the limiting oxygen index (LOI) testing results show that the LOI values of the PS–MWCNT composites were consistently higher than 27%; this indicated that the PS–MWCNT composites effectively met the needs of flame safety; this indicated that the PS–MWCNT–IFR composite is a novel and promising candidate for an ideal EMI shielding material with excellent flame‐retardant properties for today's electronic devices. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45088.     

Graphene nanoplate and multiwall carbon nanotube–embedded polycarbonate hybrid composites: High electromagnetic interference shielding with low percolation threshold

This study has reported the preparation of polycarbonate (PC)/graphene nanoplate (GNP)/multiwall carbon nanotube (MWCNT) hybrid composite by simple melt mixing method of PC with GNP and MWCNT at 330°C above the processing temperature of the PC (processing temperature is 280°C) followed by compression molding. Through optimizing the ratio of (GNP/MWCNT) in the composites, high electromagnetic interference shielding effectiveness (EMI SE) value (∼21.6 dB) was achieved at low (4 wt%) loading of (GNP/MWCNT) and electrical conductivity of ≈6.84 × 10⁻⁵ S.cm⁻¹ was achieved at 0.3 wt% (GNP/MWCNT) loading with low percolation threshold (≈0.072 wt%). The high temperature melt mixing of PC with nanofillers lowers the melt viscosity of the PC that has helped for better dispersion of the GNPs and MWCNTs in the PC matrix and plays a key factor for achieving high EMI shielding value and high electrical conductivity with low percolation threshold than ever reported in PC/MWCNT or PC/graphene composites. With this method, the formation of continuous conducting interconnected GNP‐CNT‐GNP or CNT‐GNP‐CNT network structure in the matrix polymer and strong π–π interaction between the electron rich phenyl rings and oxygen atom of PC chain, GNP, and MWCNT could be possible throughout the composites. POLYM. COMPOS., 37:2058–2069, 2016. © 2015 Society of Plastics Engineers     

Comparative study of electromagnetic interference shielding properties of injection molded versus compression molded multi-walled carbon nanotube/polystyrene composites

This study compares electromagnetic interference (EMI) shielding properties of injection molded versus compression molded multi-walled carbon nanotube/polystyrene (MWCNT/PS) composites, i.e., properties such as EMI shielding effectiveness (EMI SE), electrical conductivity, real permittivity and imaginary permittivity. The injection molded (MWCNT-aligned) samples showed lower EMI shielding properties than compression molded (randomly distributed MWCNT) samples that was attributed to lower probability of MWCNTs contacting each other due to MWCNT alignment. The compression molded samples showed higher electrical conductivity and lower electrical percolation threshold than the injection molded samples. The compression molded samples at MWCNT concentrations of 5.00 and 20.0 wt.% showed real permittivity two times and imaginary permittivity five times greater than the injection molded samples. The EMI SE for the compression molded samples at MWCNT concentrations of 5.00 and 20.0 wt.% was 15.0 and 30.0 dB, respectively, significantly greater than EMI SE for the injection molded samples. Lower EMI SE for the injection molded samples was ascribed to lower electrical conductivity, real permittivity (polarization loss) and imaginary permittivity (Ohmic loss). Comparison of the EMI shielding properties of the compression molded versus injection molded samples confirmed that EMI shielding does not require filler connectivity; however it increases with filler connectivity.     

Properties of microinjection molding of polymer multiwalled carbon nanotube conducting composites

The effects of processing conditions on the microstructure and properties of polypropylene/multiwalled carbon nanotube (PP/MWCNT) and polycarbonate/multiwalled carbon nanotube (PC/MWCNT) composites were studied. Samples of various MWCNT loadings were prepared by diluting commercial masterbatches. Different processing conditions were then used to systematically change the degree of nanotube alignment, from random to highly aligned. The crystallinity of the PP/MWCNT nanocomposites was found to go through a maximum as a function of nanotube content while the overall rate of crystallization increased. For the highly sheared microinjected PP/MWCNT samples well oriented crystals were formed. Electrical conductivity of the nanocomposites was improved by the presence of the crystalline structure; however, the high degree of nanotube alignment in the microparts resulted in a significant increase in the electrical percolation threshold. The PP nanocomposites exhibited mechanical properties significantly enhanced by nanotube loading; this effect was small in the case of the PC nanocomposites. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Effects of carbon fiber modification with multiwall CNT on the electrical conductivity and EMI shielding effectiveness of polycarbonate/carbon fiber/CNT composites

The effect of carbon fiber (CF) modification with multiwall carbon nanotube (CNT) on the electrical, mechanical, and rheological properties of the polycarbonate (PC)/CF/CNT composite was investigated. The CF and multiwall CNT (MWCNT) were treated with sulfuric acid and nitric acid (3:1 wt %) mixture, to modify the CF with the CNT. For the PC with acid-treated CNT (a-CNT) modified acid-treated CF (a-CF) (PC/a-CF/a-CNT) composite, the electrical conductivity, and the electromagnetic interference shielding effectiveness (EMI SE) showed the highest values, compared with those of the PC/a-CF and PC/a-CF/CNT composites. The EMI SE of the PC/a-CF (10 wt %)/a-CNT (0.5 wt %) composite was found to be 26 (dB at the frequency of 10.0 GHz, and the EMI SE was increased by 91.2%, compared to that of the PC/a-CF composite at the same amount of total filler content. Among the composites studied in this work, the PC/a-CF/a-CNT composite also showed the highest values of relative permittivity (ε_r) and dielectric loss factor. The above results suggest that the CF modification with the a-CNT significantly affected the electrical conductivity and EMI SE of the composite, and the hybrid fillers of the a-CNT and a-CF resulted in good electrical pathways in the PC/a-CF/a-CNT composite. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47302.     

Electrical and electromagnetic interference shielding properties of flow-induced oriented carbon nanotubes in polycarbonate

The electrical and electromagnetic interference shielding effectiveness (EMI SE) properties of multi-walled carbon nanotubes/polycarbonate (MWCNT/PC) composites are investigated. The composites were prepared by diluting masterbatch (15 wt.% MWCNT) using a Haake mixer and then injection-molded into a dog-bone mold. Various MWCNT alignments were created by changing operating conditions. Electrical resistivity measurements were carried out at three different areas at both parallel and perpendicular to the flow direction. The results showed higher resistivity and percolation threshold at higher alignments in both parallel and perpendicular to the flow direction. By applying Ohm’s law it was seen that after percolation, the field emission mechanisms are more important at higher orientations. Higher MWCNT alignments were observed in areas with higher resistivities, and this was verified using SEM, TEM and Raman spectroscopy techniques. Additionally, EMI SE measurements were done on compression-molded samples at different concentrations and thicknesses. The results showed that both EMI SE by reflection and absorption increased with increase in MWCNT loading and shielding material thickness.