Electrochemical determination of arsenite using a gold nanoparticle modified glassy carbon electrode and flow analysis

A flow analysis electrochemical system has been developed, characterized, and optimized for the determination of arsenite (As(III)). Sensitivity was significantly improved by the electrochemical deposition of gold nanoparticles on a dual glassy carbon electrode, which was inserted into a cross-flow thin-layer electrochemical cell. The electrochemical system was linear up to 15 ppb with a detection limit of 0.25 ppb. Gold deposition was evident from cyclic voltammetry measurements, whereas atomic force microscopy and scanning electron microscopy revealed the size and distribution of deposited gold nanoparticles. The size and density of the nanoparticles were related to the gold salt concentration, deposition time, and potential as well as the electrode position. The response to arsenite was directly related to the frequency, increment, and amplitude of the square wave voltammetry as well as the deposition time and potential. Estimated reproducibility was +/-1.1% at 95% confidence interval for 40 repeated analyses of 8 ppb arsenite during continuous analysis. The reproducibility was far superior if the electrochemical reduction of arsenite was performed in nitric acid instead of hydrochloric or sulfuric acid. The electrochemical system was applicable for analysis of spiked arsenic in mineral water containing a significant amount of various ion elements.     

Fabrication of cone-shaped boron doped diamond and gold nanoelectrodes for AFM-SECM

We demonstrate a reliable microfabrication process for a combined atomic force microscopy (AFM) and scanning electrochemical microscopy (SECM) measurement tool. Integrated cone-shaped sensors with boron doped diamond (BDD) or gold (Au) electrodes were fabricated from commercially available AFM probes. The sensor formation process is based on mature semiconductor processing techniques, including focused ion beam (FIB) machining, and highly selective reactive ion etching (RIE). The fabrication approach preserves the geometry of the original AFM tips resulting in well reproducible nanoscaled sensors. The feasibility and functionality of the fully featured tips are demonstrated by cyclic voltammetry, showing good agreement between the measured and calculated currents of the cone-shaped AFM-SECM electrodes.     

Platinum nanoparticle modified polyaniline-functionalized boron nitride nanotubes for amperometric glucose enzyme biosensor

A novel amperometric biosensor based on the BNNTs-Pani-Pt hybrids with Pt nanoparticle homogeneously decorated on polyaniline (Pani)-wrapped boron nitride nanotubes (BNNTs), was developed. It is shown that π interactions take place between BNNTs and polyaniline (Pani) located at N atoms from BNNTs and C atoms from Pani, resulting in the water solubility for the Pani wrapped BNNTs hybrids. The developed glucose biosensor displayed high sensitivity and stability, good reproducibility, anti-interference ability, especially excellent acid stability and heat resistance. The resulted BNNTs-Pani-Pt hybrid amperometric glucose biosensor exhibited a fast response time (within 3 s) and a linear calibration range from 0.01 to 5.5 mM with a high sensitivity and low detection limit of 19.02 mA M(-1) cm(-2) and 0.18 μM glucose (S/N = 3). Surprisedly, the relative activity of the GC/BNNTs-Pani-Pt-GOD electrode keeps almost no change in a range from pH 3 to 7. Futhermore, the BNNTs-Pani-Pt hybrid biosensor maintains a high GOD enzymatic activity even at a relatively high temperature of 60 °C. This might be attributed to the effect of electrostatic field and hydrophobia of BNNTs. The unique acid stability and heat resistance of this sensor indicate great promising application in numerous industrial and biotechnological operations involving harsh conditions.     

壳聚糖修饰掺硼金刚石薄膜电极测定铜离子

通过热丝化学气相沉积(HFCVD)的方法,以钽(Ta)为衬底,三氧化二硼(Be2O3)为硼源,制备掺硼金刚石(BDD)薄膜.并采用共价键合法进一步制得壳聚糖修饰BDD薄膜电极.以此修饰电极为工作电极,在0.1mol/L,pH=4的磷酸氢二钠缓冲液中对Cu2+进行检测.实验表明,Cu2+在4.0×10-7～1.0×10-...     

Raman spectroscopy of diamond and doped diamond

The optimization of diamond films as valuable engineering materials for a wide variety of applications has required the development of robust methods for their characterization. Of the many methods used, Raman microscopy is perhaps the most valuable because it provides readily distinguishable signatures of each of the different forms of carbon (e.g. diamond, graphite, buckyballs). In addition it is non-destructive, requires little or no specimen preparation, is performed in air and can produce spatially resolved maps of the different forms of carbon within a specimen. This article begins by reviewing the strengths (and some of the pitfalls) of the Raman technique for the analysis of diamond and diamond films and surveys some of the latest developments (for example, surface-enhanced Raman and ultraviolet Raman spectroscopy) which hold the promise of providing a more profound understanding of the outstanding properties of these materials. The remainder of the article is devoted to the uses of Raman spectroscopy in diamond science and technology. Topics covered include using Raman spectroscopy to assess stress, crystalline perfection, phase purity, crystallite size, point defects and doping in diamond and diamond films.     

Biosensor for arsenite using arsenite oxidase and multiwalled carbon nanotube modified electrodes

A biosensor for arsenite has been developed using molybdenum-containing arsenite oxidase, prepared from the chemolithoautotroph NT-26 that oxidizes arsenite to arsenate. The enzyme was galvanostatically deposited for 10 min at 10 microA onto the active surface of a multiwalled carbon nanotube modified glassy carbon electrode. The resulting biosensor enabled direct electron transfer, i.e., effecting reduction and then reoxidization of the enzyme without an artificial electron-transfer mediator. Arsenite was detected within 10 s at an applied potential of 0.3 V with linearity up to 500 ppb and a detection limit of 1 ppb. The biosensor exhibited excellent reproducibility, 2% at 95% confidence interval for 12 repeated analyses of 25 ppb arsenite. Copper, a severe interfering species commonly found in groundwater, did not interfere, and the biosensor was applicable for repeated analysis of spiked arsenite in tap water, river water, and a commercial mineral water.     

Detection of hydrogen peroxide at mesoporous platinum microelectrodes

Mesoporous (H(I)-ePt) platinum microelectrodes electrodeposited from the hexagonal (H(I)) lyotropic liquid crystalline phase are shown to be excellent amperometric sensors for the detection of hydrogen peroxide over a wide range of concentrations. Good reproducibility, high precision, and accuracy of measurements are demonstrated. Mesoporous microelectrodes retain the high rates of mass transport typical of conventional microelectrodes, and their high real surface area greatly enhances their catalytic activity. This unique combination of properties overcomes the limitations of previous amperometric hydrogen peroxide sensors and yields outstanding qualitative and quantitative results.     

Application of diamond microelectrodes for end-column electrochemical detection in capillary electrophoresis

Highly boron-doped diamond microelectrodes were employed in an end-column electrochemical detector for capillary electrophoresis (CE). The diamond microline electrodes were fabricated from conducting diamond thin films (exposed surface area, 300 x 50 microm), and their analytical performance as CE detectors was evaluated in a laboratory-made CE installation. The CE-ED system exhibited high separation efficiency for the detection of several catecholamines, including dopamine (DA), norepinephrine (NE), and epinephrine (E), with excellent analytical performance, for example, 155,000 theoretical plates for DA. The diamond-based electrochemical detection system also displayed low detection limits (approximately 20 nM for E at S/N = 3) and a highly reproducible current response with 10 repetitive injections of mixed analytes containing DA, NE, and E (each 50 microM), with relative standard deviations (RSD) of approximately 5%. The performance of the diamond detector in CE was also evaluated in the detection of chlorinated phenols (CP). When compared to the carbon fiber microelectrode, the diamond electrode exhibited lower detection limits in an end-column CE detection resulting from very low noise levels and highly reproducible analyses without electrode polishing due to analyte fouling, which makes it possible to perform easier and more stable CE analysis.     

Boron-doped diamond microelectrodes for use in capillary electrophoresis with electrochemical detection

The fabrication and characterization of boron-doped diamond microelectrodes for use in electrochemical detection coupled with capillary electrophoresis (CE-EC) is discussed. The microelectrodes were prepared by coating thin films of polycrystalline diamond on electrochemically sharpened platinum wires (76-, 25-, and 10-microm diameter), using microwave-assisted chemical vapor deposition (CVD). The diamond-coated wires were attached to copper wires (current collectors), and several methods were explored to insulate the cylindrical portion of the electrode: nail polish, epoxy, polyimide, and polypropylene coatings. The microelectrodes were characterized by scanning electron microscopy, Raman spectroscopy, and cyclic voltammetry. They exhibited low and stable background currents and sigmoidally shaped voltammetric curves for Ru(NH3)6(3+/2+) and Fe(CN)6(3-/4-) at low scan rates. The microelectrodes formed with the large diameter Pt and sealed in polypropylene pipet tips were employed for end-column detection in CE. Evaluation of the CE-EC system and the electrode performance were accomplished using a 10 mM phosphate buffer, pH 6.0, run buffer, and a 30-cm-long fused-silica capillary (75-microm i.d.) with dopamine, catechol, and ascorbic acid serving as test analytes. The background current (approximately 100 pA) and noise (approximately 3 pA) were measured at different detection potentials and found to be very stable with time. Reproducible separation (elution time) and detection (peak current or area) of dopamine, catechol, and ascorbic acid were observed with response precisions of 4.1% or less. Calibration curves constructed from the peak area were linear over 4 orders of magnitude, up to a concentration between 0.1 and 1 mM. Mass limits of detection for dopamine and catechol were 1.7 and 2.6 fmol, respectively (S/N = 3). The separation efficiency was approximately 33,000, 56,000, and 98,000 plates/m for dopamine, catechol, and ascorbic acid, respectively. In addition, the separation and detection of 1- and 2-naphthol in 160 mM borate buffer, pH 9.2, was investigated. Separation of these two analytes was achieved with efficiencies of 118,000 and 126,000 plates/m, respectively.     

Copper determination in urine by flow injection analysis with electrochemical detection at platinum disk microelectrodes of various radii

The incorporation of platinum disk microelectrodes of various radii (2.5-50 microns) in a well-jet flow cell offers reduced limits of detection for the determination of copper in urine by flow injection analysis compared with standard methods based on a conventional sized glassy carbon disk macroelectrode (radius 1.5 mm), in a thin-layer cell. The radius of the platinum disk microelectrode was found to be critical with respect to both the limit of detection and flow rate dependence. An optimal radius value of 28 microns was found with detection limits increasing with both larger and smaller electrode radii. In contrast, as theoretically expected, a diminished flow rate dependence was observed the smaller the radii of the platinum disk microelectrodes. Sample cleanup and preparation is conveniently achieved by the use of Sep-Pak cartridges and formation of a copper dithiocarbamate complex. The metal complex is easily oxidized at platinum disk microelectrodes in acetonitrile, which was the solvent used in the flow injection method of analysis.     

Factors controlling stripping voltammetry of lead at polycrystalline boron doped diamond electrodes: new insights from high-resolution microscopy

We report wide-ranging studies to elucidate the factors and issues controlling stripping voltammetry of metal ions on solid electrodes using the well-known Pb/Pb(2+) couple on polycrystalline boron doped diamond (pBDD) as an exemplar system. Notably, high-resolution microscopy techniques have revealed new insights into the features observed in differential pulse anodic stripping voltammetry (DPV-ASV) which provide a deeper understanding of how best to utilize this technique. DPV-ASV was employed in an impinging wall-jet configuration to detect Pb(2+) in the nanomolar to micromolar concentration range at a pBDD macrodisk electrode. The deposition process was driven to produce a grain-independent homogeneous distribution of Pb nanoparticles (NPs) on the electrode surface; this resulted in the observation of narrow stripping peaks. Lower calibration gradients of current or charge versus concentration were found for the low concentrations, correlating with a lower than expected (from consideration of the simple convective-diffusive nature of the deposition process) amount of Pb deposited on the surface. This was attributed to the complex nature of nucleation and growth at solid surfaces in this concentration regime, complicating mass transport. Furthermore, a clear shift negative in the stripping peak potential with decreasing concentration was seen correlating with a change in the size of the deposited NP, suggesting an NP size-dependent redox potential for the Pb/Pb(2+) couple. At high concentrations a nonlinear response was observed, with less Pb detected than expected, in addition to the observation of a second stripping peak. Atomic force microscopy (AFM) and field emission scanning electron microscopy revealed the second peak to be due to a change in deposition morphology from isolated NPs to grain-independent heterogeneous structures comprising both thin films and NPs; the second peak is associated with stripping from the thin-film structures. AFM also revealed a substantial amount of Pb remaining on the surface after stripping at high concentration, explaining the nonlinear relationship between stripping peak current (or charge) and concentration. Finally, the use of an in situ cleaning procedure between each measurement was advocated to ensure a clean Pb-free surface (verified by AFM and X-ray photoelectron spectroscopy analysis) between each run. The studies herein highlight important and complex physicochemical processes involved in the electroanalysis of heavy metals at solid electrodes, such as pBDD, that need to be accounted for when using stripping voltammetry methods.     

Properties of boron doped Tl-Ba-Ca-Cu-O superconductors

The effects of boron doping on the formation and properties of the Tl-based superconductors have been studied. Up to 10 wt.% boron has been added to the oxides having the nominal composition, Tl_1.8Ba₂Ca_2.2Cu₃O_x, by the usual solid-state reaction method. Boron additions in the range 0.8-1.0% increase the fraction of the Tl-2223 phase and significantly improve the critical temperature of the samples. Higher amounts of boron additions eliminate the Tl-2223 phase, reduce the fraction of Tl-2212 phase and cause separate non-superconducting phases to be formed. The formation of non-superconducting phases does not allow us to obtain pure Tl-2212 phase.     

Enzyme modification of platinum microelectrodes for detection of cholesterol in vesicle lipid bilayer membranes

Platinum microelectrodes are modified with a lipid bilayer membrane incorporating cholesterol oxidase. Details for electrode surface modification are presented along with characterization studies of electrode response to cholesterol solution and to cholesterol contained in the lipid bilayer membrane of vesicles. Ferrocyanide voltammetric experiments are used to track deposition of a submonolayer of a thiol-functionalized lipid on the platinum electrode surface, vesicle fusion for bilayer formation on the thiolipid-modified surface, and incorporation of cholesterol oxidase in the electrode-supported thiolipid/lipid bilayer membrane. The data are consistent with formation of a lipid bilayer structure on the electrode surface that contains defects. Experiments for detection of cholesterol solubilized in cyclodextrin solution show steady-state current responses that correlate with cholesterol concentration. Direct contact between the electrode and a vesicle lipid bilayer membrane shows a response that correlates with vesicle membrane cholesterol content.     

Fabrication and characterization of laser pulled platinum microelectrodes with controlled geometry

The development of a reproducible procedure for the fabrication of Pt disk-shaped microelectrodes with characteristic dimensions ranging from 50 nm to 1 μm in diameter was carried out using a laser pulling technique. The governing physical phenomena involved in their fabrication are discussed, and the importance of adding a critical quartz thinning step in the general procedure is demonstrated. The preparation of the microelectrodes involves sealing a platinum wire inside a quartz tubing using a pipet puller, thinning the composite material (platinum/quartz assembly), and laser pulling it to obtain two microelectrodes. The resulting microelectrodes display reproducible well-controlled geometry, which is important to downstream quantitative scanning electrochemical studies and imaging. Mechanical polishing of the microelectrode is required and remains the critical step in the fabrication of nanometer size electrodes. Following production, the microelectrodes are characterized by electron microscopy, scanning electrochemical microscopy, and cyclic voltammetry. Development of these microelectrodes is motivated by their subsequent application to electrocatalysis and their potential in theoretical study because of their well-defined geometry.     

Preparation of platinum nanoparticle and its catalytic activity for toluene oxidation

Colloidal Pt nanoparticles are prepared using H2PtCl6 as a precursor, polyvinylpyrrolidone (PVP: molecular weight = 10,000 and 40,000) and hydrogen as a stabilizing agent and a reducing agent, respectively. The amounts of the precursor and the stabilizing agent and the molecular weight of PVP have an effect on the formation of Pt nanoparticles. Supported Pt catalyst (CSPt) is prepared from colloidal Pt nanoparticles and y-Al2O3. Another supported Pt catalyst (ISPt) is prepared by using the conventional incipient wetness impregnation method with an aqueous H2PtCl6 solution and gamma-Al2O3. The catalytic activities of CSPt and ISPt catalysts are compared for VOC (toluene) oxidation. Transmission Electron Microscopy (TEM), UV-vis, X-ray diffraction (XRD) and temperature programmed reduction (TPR) are used to characterize CSPt and ISPt catalysts. The experimental results reveal that the catalytic activity of CSPt is superior to that of ISPT.     

Fabrication, characterization, and application of boron-doped diamond microelectrodes for in vivo dopamine detection

Highly boron-doped diamond (BDD) was deposited on chemically etched micrometer-sized tungsten wires using microwave plasma assisted chemical vapor deposition (MPCVD), and these were used to fabricate BDD microelectrodes. BDD microelectrodes with very small diameter (about 5 microm) and 250 microm in length could be made successfully. In addition to the unique properties of BDD electrodes, such as a very low background current, high stability, and selective oxidation of dopamine (DA) in the presence of ascorbic acid (AA), other superior properties of the microelectrodes, including a constant current response, an increase in the mass transport, and the ability for use in high resistance media were also shown. An application study was conducted for in vivo detection of DA in mouse brain, where the BDD microelectrode was inserted into the corpus striatum of the mouse brain. A clear signal current response following medial forebrain bundle (MFB) stimulation could be obtained with high sensitivity. Excellent stability was achieved, indicating that the BDD microelectrodes are very promising for future in vivo electroanalysis.     

Graphene supported platinum nanoparticle counter-electrode for enhanced performance of dye-sensitized solar cells

Composites of few layered graphene (G) and platinum (Pt) nanoparticles (NP) with different loadings of Pt were used as counter electrode (CE) in dye-sensitized solar cell (DSSC). NPs were deposited directly on to G using pulsed laser ablation method (PLD). DSSCs formed using the composite CEs show improved performance compared to conventional Pt thin film electrode (Std Pt) and unsupported Pt NPs. Composite with 27% loading of Pt shows 45% higher efficiency (η = 2.9%), greater short circuit current (J(sc) = 6.67 mA cm(-2)), and open circuit voltage (V(oc) = 0.74 V) without any loss of the fill factor (FF = 58%) as compared to the cells fabricated using Std Pt electrodes. Values of η, J(sc) and V(oc) for DSSC using Std Pt CE were 2%, 5.05 mA cm(-2) and 0.68 V, respectively. Electrochemical impedance spectroscopy using I(-)(3)/I(-) redox couple confirm lower values of charge transfer resistance for the composite electrodes, e.g., 2.36 Ω cm(2) as opposed to 7.73 Ω cm(2) of Std Pt. The better catalytic activity of these composite materials is also reflected in the stronger I(-)(3) reduction peaks in cyclic voltammetry scans.     

Simultaneous determination of serotonin and dopamine at the PEDOP/MWCNTs-Pd nanoparticle modified glassy carbon electrode

Electrochemical determination of dopamine (DA) and serotonin (5-HT) have been studied at a modified glassy carbon electrode (GCE) in 0.1 M phosphate buffer solution (PBS) using cyclic voltammetry (CV) and differential pulse voltammetry (DPV) at pH 7.4, all over the interfering biomolecule ascorbic acid (AA). The GCE was modified by palladium-functionalized, multi-walled carbon nanotubes (MWCNTs-Pd) with electrochemical deposition of poly 3,4-ethylenedioxy pyrrole (PEDOP), denoted as PEDOP/MWCNTs-Pd/GCE, and investigated by SEM and EIS experiments. The highly electrocatalytic activity of the modified electrode toward 5-HT and DA was demonstrated from the sensitive and well-separated voltammetric experiment. The oxidation peaks found were 0.165 and 0.355 mV for DA and 5-HT, respectively. The composite film shows a significant accumulation effects on two species, as well as the mutual interference among the analytes. This biosensor was best in response compared to other modified electrodes made in the same lab. The lowest detection limits were found to be 5.0 x 10(-9) and 1.0 x 10(-8) for 5-HT and DA, respectively. The respective linear ranges were determined as 1.0 x 10(-7) to 2.0 x 10(-4) and 1.0 x 10(-7) to 2.0 x 10(-4) for 5-HT and DA.     

endo-Fullerene and doped diamond nanocrystallite-based models of qubits for solid-state quantum computers

Models of encapsulated nuclear spin 1/2 1H and 31P atoms in fullerene and diamond nanocrystallite, respectively, are proposed and examined with an ab initio local density functional method for possible applications as single quantum bits (qubits) in solid-state quantum computers. A 1H atom encapsulated in a fully deuterated fullerene, C20D20, forms the first model system and ab initio calculation shows that the 1H atom is stable in its atomic state at the center of the fullerene with a barrier of about 1 eV to escape. A 31P atom positioned at the center of a diamond nanocrystallite is the second model system, and 31P atom is found to be stable at the substitutional site relative to interstitial sites by 15 eV. Vacancy formation energy is 6 eV in diamond, so the substitutional 31P atom will be stable against diffusion during the formation mechanisms within the nanocrystallite. The coupling between the nuclear spin and the weakly bound (valance) donor electron in both systems is found to be suitable for single qubit applications, whereas the spatial distributions of (valance) donor electron wave functions are found to be preferentially spread along certain lattice directions, facilitating two or more qubit applications. The feasibility of the fabrication pathways for both model solid-state qubit systems within practical quantum computers is discussed within the context of our proposed solid-state qubits.