Spectroscopic properties of Yb in heavy metal contained fluorophosphate glasses

A new series of 20Bi(PO₃)₃–10Sr(PO₃)₂–35BaF₂–35MgF₂ doped with Yb³⁺ is introduced for fiber and waveguide laser applications. The stimulated emission cross-section σ_emi, which was found to be 1.37 pm² at the lasing wavelength of 996 nm, is the highest one among fluorophosphate glasses. It has been found that an extremely high gain coefficient of G = 1.65 ms pm⁴ and high quantum efficiency of η = 93% for 1 wt.% Yb₂O₃ doped systems. The various concentration effects on laser performance properties including minimum pumping intensity I_min, the minimum fraction of excited ions β_min and the saturation pumping intensity I_sat are analyzed as a function of Yb₂O₃ concentration. Those results obtained in current system had advantage over some fluorophosphate glasses reported.     

A simple and an effective method for the fabrication of densified glass-ceramics of low temperature co-fired ceramics

This study reports a new, simple and effective pre-calcined method for fabrication BaO–TiO₂–B₂O₃–SiO₂ low temperature co-fired ceramics (LTCC) at a sintering temperature below 900 °C, and with dielectric losses (tan δ) lower than 2 × 10⁻³. The research results have shown that the addition of 2–5 wt% Al₂O₃ could easily eliminate the porosity of the glass-ceramics because of the excellent wetting behavior between alumina and the BaO–B₂O₃–SiO₂ glass liquid phase in the low temperature co-fired ceramic system.     

Frequency dependent electrical conductivity and dielectric relaxation behavior in amorphous (90V2O5–10Bi2O3) oxide semiconductors doped with SrTiO3

We report on the experimental results of frequency dependent a.c. conductivity and dielectric constant of SrTiO₃ doped 90V₂O₅–10Bi₂O₃ semiconducting oxide glasses for wide ranges of frequency (500–10⁴ Hz) and temperature (80–400 K). These glasses show very large dielectric constants (10²–10⁴) compared with that of the pure base glass (≈10²) without SrTiO₃ and exhibit Debye-type dielectric relaxation behavior. The increase in dielectric constant is considered to be due to the formation of microcrystals of SrTiO₃ and TiO₂ in the glass matrix. These glasses are n-type semiconductors as observed from the measurements of the thermoelectric power. Unlike many vanadate glasses, Long's overlapping large polaron tunnelling (OLPT) model is found to be most appropriate for fitting the experimental conductivity data, while for the undoped V₂O₅–Bi₂O₃ glasses, correlated barrier hopping conduction mechanism is valid. This is due to the change of glass network structure caused by doping base glass with SrTiO₃. The power law behavior (σ_ac=A(ω^s) with s<1) is, however, followed by both the doped and undoped glassy systems. The model parameters calculated are reasonable and consistent with the change of concentrations (x).     

Microstructures, densification and mechanical properties of TiC–Al2O3–Al composite by field-activated combustion synthesis

Dense TiC–Al₂O₃–Al composite was prepared with Al, C and TiO₂ powders by means of electric field-activated combustion synthesis and infiltration of the molten metal (here Al) into the synthesized TiC–Al₂O₃ ceramic. An external electric field can effectively improve the adiabatic combustion temperature of the reactive system and overcome the thermodynamic limitation of reaction with x < 10 mol. Thereby, it can induce a self-sustaining combustion synthesis process. During the formation of Al₂O₃–TiC–Al composite, Al is molten first, and reacted with TiO₂ to form Al₂O₃, followed by the formation of TiC through the reaction between the displaced Ti and C. Highly dense TiC–Al₂O₃–Al with relative density of up to 92.5% was directly fabricated with the application of a 14 mol excess Al content and a 25 V cm⁻¹ field strength, in which TiC and Al₂O₃ particles possess fine-structured sizes of 0.2–1.0 μm, with uniform distribution in metal Al. The hardness, bending strength and fracture toughness of the synthesized TiC–Al₂O₃–Al composite are 56.5 GPa, 531 MPa and 10.96 MPa m^1/2, respectively.     

Glass formation and conductivity in the Pb2P2O7–Ag4P2O7–AgI system

A large glass-forming domain has been identified in the Pb₂P₂O₇–Ag₄P₂O₇–AgI system. The physical properties have been determined as a function of AgI content. The ionic conductivity has been studied as a function of the Ag⁺ ion total concentration and the Ag⁺ ion concentration issued from the AgI component. The structure and electrical properties of obtained glasses are compared with those of ionic glasses of the Ag₄P₂O₇–AgI system.     

Structural and optical properties of (100 − x)(Li2B4O7) − x(SrO–Bi2O3–0.7Nb2O5–0.3V2O5) glasses and glass nanocrystal composites

Glasses of various compositions in the system (100 − x)(Li₂B₄O₇) − x(SrO–Bi₂O₃–0.7Nb₂O₅–0.3V₂O₅) (10  x  60, in molar ratio) were prepared by splat quenching technique. The glassy nature of the as-quenched samples was established by differential thermal analyses (DTA). The amorphous nature of the as-quenched glasses and crystallinity of glass nanocrystal composites were confirmed by X-ray powder diffraction studies. Glass composites comprising strontium bismuth niobate doped with vanadium (SrBi₂(Nb_0.7V_0.3)₂O_9−δ (SBVN)) nanocrystallites were obtained by controlled heat-treatment of the as-quenched glasses at 783 K for 6 h. High resolution transmission electron microscopy (HRTEM) of the glass nanocrystal composites (heat-treated at 783 K/6 h) confirm the presence of rod shaped crystallites of SBVN embedded in Li₂B₄O₇ glass matrix. The optical transmission spectra of these glasses and glass nanocrystal composites of various compositions were recorded in the wavelength range 190–900 nm. Various optical parameters such as optical band gap (E_opt), Urbach energy (ΔE), refractive index (n), optical dielectric constant and ratio of carrier concentration to the effective mass (N/m^*) were determined. The effects of composition of the glasses and glass nanocrystal composites on these parameters were studied.     

Highly stable persistent spectral hole burning in Eu ions doped oxy-fluoride glasses of 30CaF2–10Al2O3–60B2O3

High temperature persistent spectral hole burning up to room temperature has been observed in Eu³⁺ ions doped oxy-fluoride glasses with a composition of 30CaF₂–10Al₂O₃–60B₂O₃ (mol%) melted in a reducing atmosphere. The hole stability was studied through light-induced hole refilling and temperature cycling experiments. The burned holes survive thermal cycling to 300 K due to a high barrier height of 0.69 eV in the sample.     

Effect of radiation trapping on the emission properties of Er: I13/2 → I15/2 transition in oxide glasses

The effect of radiation trapping on the emission properties of Er³⁺-doped tellurite and phosphate glasses has been investigated as the function of sample thickness and doping concentration. It was found that radiation trapping exists generally in two glass matrices, even at low doping concentration (0.1 mol% Er₂O₃). The larger effect of radiation trapping in tellurite glasses compared with phosphate glasses is due to its larger emission cross-section at 1.5 μm band and the spectral overlap between the emission and absorption spectra of Er³⁺: ⁴I_13/2 ↔ ⁴I_15/2transition. Due to radiation trapping, the measured lifetime of the Er³⁺: ⁴I_13/2 level in tellurite glasses increases by about 11–37% with increasing the sample thickness at the different erbium doping concentration, while 6–17% for phosphate glasses. And the full-width at half maximum of fluorescence (FWHM) of Er³⁺: ⁴I_13/2 → ⁴I_15/2 transition in tellurite glasses increased by about 15–64% with increasing the sample thickness, while 11–55% for phosphate glasses. It caused a high overestimation on the figure of merits (FOM) for amplifier bandwidth (σ_e × FWHM).     

Phase relations, lattice thermal expansion in Ce1−xEuxO2−x/2 and Ce1−xSmxO2−x/2 systems and stabilization of cubic RE2O3 (RE: Eu, Sm)

The phase relations in CeO₂–Eu₂O₃ and CeO₂–Sm₂O₃ systems have been established under slow-cooled conditions from 1400 °C. The two-phase relations differ as the CeO₂–Eu₂O₃ system showed only two monophasic phase fields, namely F-type cubic and C-type cubic, whereas CeO₂–Sm₂O₃ system showed three phase fields namely F-type cubic, C-type cubic and a biphasic field comprising of C-type cubic and monoclinic phase. An interesting observation of this investigation is the stabilization of C-type rare-earth oxide after Ce⁴⁺ substitution, which is attributed to decrease in average cationic size on Ce⁴⁺ substitution at RE³⁺ site. The lattice thermal expansion behavior of F-type solid solution and C-type solid solution in CeO₂–Eu₂O₃ system was investigated by high-temperature XRD.     

On the structure of the NiO–Al2O3 systems, studied by diffuse-reflectance spectroscopy

Diffuse-reflectance spectra of the NiO–Al₂O₃ systems in the 350–800 nm spectral domain are analysed. Two types of Ni²⁺complexes in γ-Al₂O₃ have been found at low concentrations (<5%): [Ni²⁺6O²⁻] and [Ni²⁺4O²⁻] with octahedral (O_h) and tetrahedral (T_d) symmetries, respectively. Coexistence of these two complexes is discussed in connection with the sample preparation and their thermal treatment.     

Optical absorption of Nd, Sm and Dy in bismuth borate glasses with large radiative transition probabilities

This paper reports on the optical properties of Nd³⁺, Sm³⁺ and Dy³⁺ in bismuth borate glasses, with Bi₂O₃ content varying from 30 to 60 mol%. The variation of the optical properties with composition plays a dominant role in determining a good laser host material. The variation of the Judd–Ofelt intensity parameters Ω_t (t=2,4,6) and the radiative transition probabilities and the hypersensitive band positions, with composition, have been discussed in detail. The changes in position and intensity parameters of the transitions in the optical absorption spectra are correlated to the structural changes in the host glass matrix. The variation of Ω₂ with Bi₂O₃ content has been attributed to changes in the asymmetry of the ligand field at the rare earth ion site and to the changes in their rare earth–oxygen (R–O) covalency, whereas the variation of Ω₆ strongly depends on nephlauxetic effect. The shift of the hypersensitive band shows that the covalency of the R–O bond increases with increase of Bi₂O₃ content, due to increased interaction between the rare earth ions and the non-bridging oxygens. The radiative transition probabilities of the rare earth ions are large in bismuth borate glasses, suggesting their suitability for laser applications.     

Preparation and optical properties of sol–gel derived Er-doped Al2O3–Ta2O5 films

Thin films of the system xAl₂O₃–(100 − x)Ta₂O₅–1Er₂O₃ were prepared by a sol–gel method and a dip-coating technique. The influences of the composition and the crystallization of the films on Er³⁺ optical properties were investigated. Results of X-ray diffraction indicated that the crystallization temperature of Ta₂O₅ increased from 800 to 1000 °C with increased values of x. In crystallized films, the intensities of the visible fluorescence and upconversion fluorescence tend to decrease with an increase in x values, due to the high phonon energy of Al₂O₃; the strongest fluorescence is observed in a crystallized film for x = 4 heat treated at 1000 °C. In amorphous films obtained by heat treatment at relatively low temperatures the Er³⁺ fluorescence could not be observed because strong fluorescence from organic residues remaining in the films thoroughly covered the Er³⁺ fluorescence. On the other hand, the Er³⁺ upconversion fluorescence in the amorphous films was observed to be stronger than that in the crystallized films. The strongest upconversion fluorescence is observed in an amorphous film for x = 75 heat treated at 800 °C.     

Low-temperature ionic conductivity of the solid solution in the system ZrO2–Y2O3–Yb2O3

Compositional dependence of ionic conductivity in the system ZrO₂–Y₂O₃–Yb₂O₃ was investigated in the temperature range 573–873 K using the complex impedance technique. It was shown that the conductivity decreases with increasing concentration of Yb₂O₃ in the system ZrO₂–Y₂O₃–Yb₂O₃. Analyzing the experimental data according to the classic Arrhenius equation showed that such an experimental phenomenon can be attributed to the tighter association between Yb³⁺ and oxygen vacancy, compared with that between Y³⁺ and oxygen vacancy, which hinders the migration of oxygen vacancy in the materials.     

Raman spectroscopy and the origin of electrooptical Kerr phenomenon in niobium alkali-silicate glasses

It is shown that magnitudes of the Kerr coefficient and permittivity of 19Na₂O–11K₂O–2B₂O₃–2CdO–(66−x)SiO₂–xNb₂O₅ glasses, where 0<x<37, correlate with the content of the Na₂O·Nb₂O₅ groupings, with that content being estimated by Raman scattering data. This allows assigning to these groupings, or to other structural entities containing such groupings (for example, crystal motifs), the responsibility for high-polarizability and Kerr sensitivity of the glasses.     

Optical band gap studies on xPb3O4–(1−x)P2O5 lead[(II, IV)] phosphate glasses

A series of glasses in the xPb₃O₄–(1−x)P₂O₅ (red lead phosphate) (RLP) system with ‘x' varying from 0.075 to 0.4 were prepared by the single-step melt quenching process from Pb₃O₄ and NH₄H₂PO₄. The optical absorption spectra of these glasses have been recorded in the ultraviolet region from 200 to 400 nm and the fundamental absorption edges have been identified. The optical band gap E_opt values have been determined for all the glasses using the known theories. The (E_opt) values vary from 4.90 to 3.21 eV the highest being 4.57 eV, corresponding to the most stable glass of x=0.225. The absorption edge is attributed to the indirect transitions and the origin of the Urbach energy ΔE is suggested to be thermal vibrations. These glasses promise as potential candidates for application in optical technology compared to simple xPbO–(1−x)P₂O₅ (lead phosphate) (LP) glasses.     

Effect of β-spodumene on the phase development in an alumina/aluminium-titanate system

The effect of β-spodumene additions on the in situ phase formation and abundances in an Al₂O₃–Al₂TiO₅ system in the temperature range 1000–1400 °C has been studied by neutron diffraction and differential thermal analysis. Results show that β-spodumene began to decompose by phase separation and partial melting at 1290 °C, followed by complete melting at 1330 °C. Formation of Al₂TiO₅ was observed to occur at 1310 °C and its abundance increased with temperature. The addition of β-spodumene as a sintering aid did not cause its reaction with alumina or rutile to form additional phases. Addition of β-spodumene in excess of 5 wt% resulted in pronounced vitrification, which partly recrystallised when cooled to room temperature. The temperatures of Al₂TiO₅ formation and melting of β-spodumene are consistent with the results of differential thermal analysis.     

Influence of Mn doping on microstructure and DC-accelerated aging behaviors of ZnO–V2O5-based varistors

The microstructure, electrical properties, dielectric characteristics, and DC-accelerated aging behavior of the ZnO–V₂O₅–MnO₂ system sintered were investigated for MnO₂ content of 0.0–2.0 mol% by sintering at 900 °C. For all samples, the microstructure of the ZnO–V₂O₅–MnO₂ system consisted of mainly ZnO grain and secondary phase Zn₃(VO₄)₂. The incorporation of MnO₂ to the ZnO–V₂O₅ system was found to restrict the abnormal grain growth of ZnO. The nonlinear properties and stability against DC-accelerated aging stress improved with the increase of MnO₂ content. The ZnO–V₂O₅–MnO₂ system added with MnO₂ content of 2.0 mol% exhibited not only a high nonlinearity, in which the nonlinear coefficient is 27.2 and the leakage current density is 0.17 mA/cm², but also a good stability, in which %ΔE_1 mA = −0.6%, %Δ = −26.1%, and %Δtan δ = +22% for DC-accelerated aging stress of 0.85E_1 mA/85 °C/24 h.     

Infrared optical properties of Bi2Ti2O7 thin films by spectroscopic ellipsometry

Bi₂Ti₂O₇ thin films have been grown directly on n-type GaAs (1 0 0) by the chemical solution decomposition technique. X-ray diffraction analysis shows that the Bi₂Ti₂O₇ thin films are polycrystalline. The optical properties of the thin films are investigated using infrared spectroscopic ellipsometry (3.0–12.5 μm). By fitting the measured ellipsometric parameter (Ψ and Δ) data with a three-phase model (air/Bi₂Ti₂O₇/GaAs), and Lorentz–Drude dispersion relation, the optical constants and thickness of the thin films have been obtained simultaneously. The refractive index and extinction coefficient increase with increasing wavelength. The fitted plasma frequency ω_p is 1.64×10¹⁴ Hz, and the electron collision frequency γ is 1.05×10¹⁴ Hz, and it states that the electron average scattering time is 0.95×10⁻¹⁴ s. The absorption coefficient variation with respect to increasing wavelength has been obtained.     

Electrical properties of glasses in the Na2O–MoO3–P2O5 system

A range of coloured electronic or mixed ionic–electronic glasses has been evidenced in the Na₂O–MoO₃–P₂O₅ system. The properties of these glasses have been studied along different composition lines corresponding either to a fixed Na₂O content or a constant Mo/P ratio. An EPR spectroscopy investigation of these glasses has allowed to determine the Mo⁵⁺ ion percentages in these materials. The electrical properties of these glasses have been studied by impedance spectroscopy, and the electronic and ionic contributions have been evaluated. The properties of these sodium glasses have been compared with those of lithium glasses with the same compositions.     

Piezoelectric and dielectric properties of PZT–PZN–PMS ceramics prepared by molten salt synthesis method

Piezoelectric powders and ceramics with the composition of Pb_0.95Sr_0.05(Zr_0.52Ti_0.48)O₃–Pb(Zn_1/3Nb_2/3)O₃–Pb(Mn_1/3Sb_2/3)O₃ (PZT–PZN–PMS) were prepared by molten salt synthesis (MSS) and conventional mixed-oxide (CMO) methods, respectively. The influence of synthesis process on the properties of powders and ceramics were investigated in detail. The results show that the MSS method significantly improved the sinterability of PZT–PZN–PMS ceramics, resulting in an improvement of dielectric and piezoelectric properties compared to the CMO method. The optimum values of MSS samples are as follows: _r = 1773; tan δ = 0.0040; T_c = 280 °C; d₃₃ = 455 pC/N; k_p = 0.70; Q_m = 888; E_c = 10.3 kV/cm; and P_r = 28.2 μC/cm², at calcination of 800 °C and sintering of 1120 °C temperature.