水泥-矿渣复合胶凝材料硬化浆体的微观结构（英文）

利用压汞法、扫描电子显微镜和透射电子显微镜研究了两种不同养护条件下水泥-矿渣复合胶凝材料硬化浆体的微观结构。结果表明:常温养护3 d龄期时,随着矿渣的掺入和掺量的增加,硬化浆体的孔隙率越大,大孔含量越多;硬化浆体微观形貌显示,掺矿渣试样的反应程度比纯水泥试样更低,密实程度较差。水化后期,复合胶凝材料的水化程度虽然比纯水泥试样低,但复合试样的孔隙率更低,孔径细化。纯水泥试样中水化硅酸钙(C-S-H)凝胶的微观形貌呈单向分布的纤维状,而复合胶凝材料试样中矿渣反应生成的C-S-H凝胶呈三维分布的箔片状,能更有效的隔断和填充连通的孔隙。在高温养护条件下,掺矿渣复合胶凝材料硬化浆体早期和后期孔隙率均较低,高温激发了矿渣早期的活性。     

温度对水泥-矿渣复合胶凝材料水化的影响（英文）

研究了温度对水泥-矿渣复合胶凝材料硬化浆体微观结构及净浆和砂浆后期强度的影响。利用背散射图像分析法测定了硬化浆体中水泥和矿渣各自的反应程度。探讨了水泥-矿渣复合胶凝材料水化程度、微观结构和力学性能之间的关系。结果表明:温度对纯水泥的水化程度影响很小,但高温(60℃)降低了纯水泥净浆的后期抗压强度。高温阻碍了复合胶凝材料浆体中水泥的后期水化,但促进了矿渣的水化,提高了矿渣的后期反应程度。高温下矿渣持续反应使硬化浆体的孔结构细化,使复合胶凝材料净浆的后期抗压强度与常温养护时相近。高温对水泥-矿渣复合胶凝材料砂浆后期抗压强度的不利影响大于净浆后期抗压强度。高温养护并不导致水泥-矿渣复合胶凝材料的后期水化程度降低。复合胶凝材料的水化程度与强度不呈线性相关。     

高炉镍铁渣粉在水泥基复合胶凝材料中的水化特性研究

通过对不同高炉镍铁渣掺量的水泥-高炉镍铁渣粉复合胶凝材料水化放热速率、高炉镍铁渣粉的反应程度、硬化浆体化学结合水含量以及水化产物中C-S-H凝胶Ca/Si的测定,分别研究了水泥-高炉镍铁渣粉复合胶凝材料的早期、中长期水化进程、浆体微观形貌以及水化产物特点等水化特性.研究结果表明:高炉镍铁渣的掺入会降低水化放热速率,并推迟水化加速期放热峰的出现时间;在复合胶凝体系中,随着高炉镍铁渣粉掺量的增大,其反应程度和硬化浆体中化学结合水含量将降低.复合胶凝材料水化生成的C-S-H凝胶的Ca/Si低于水泥,且随着水化的进行呈降低趋势;高炉镍铁渣粉中的Al,在水化过程中会取代部分Si进入C-S-H凝胶中,形成C-A-S-H凝胶.     

大掺量钢渣复合胶凝材料早期水化性能和浆体结构

通过对胶凝材料早期水化放热性能和水化产物种类的测定,以及对硬化浆体显微形貌和孔结构的观察,研究了大掺量钢渣复合胶凝材料的早期水化性能和硬化浆体结构.结果表明:钢渣具有弱胶凝性能,早期活性低,大掺量钢渣使复合胶凝材料的水化诱导期延长,水化放热量降低,但对水泥早期的水化产物形成过程影响很小.大掺量钢渣复合胶凝材料早期的硬化浆体结构较疏松,孔隙率高于纯水泥浆体,且大孔数量较多.     

矿渣-水泥复合胶凝体系低温水化动力学研究

研究了低温下矿渣-水泥复合胶凝体系的水化反应特性和水化反应动力学.研究表明:低温下,复合胶凝体系的水化放热速率随着矿渣掺量的增加和环境温度的降低而下降;非蒸发水含量随着矿渣掺量的增加呈现降低的趋势;对已有水泥水化动力学方程进行计算,得到了低温条件下复合胶凝体系的动力学参数以及不同阶段反应速率和水化度间的关系,通过计算获得的动力学参数,可以对低温条件下复合胶凝体系不同反应阶段水化反应程度进行预测;在水化早期,复合胶凝体系中矿渣水化程度较低,消耗少量Ca(OH)2,使生成C-S-H凝胶的Ca/Si降低较少.在水化后期,复合胶凝体系中矿渣水化消耗较多的Ca(OH)2,使生成C-S-H凝胶的Ca/Si降低较多.矿渣掺量为50％时,硬化浆体C-S-H凝胶的Ca/Si远小于纯水泥体系.     

水泥–矿渣复合胶凝材料中矿渣的水化特性

通过对不同矿渣掺量时水泥–矿渣复合胶凝材料中矿渣的反应程度、硬化浆体中Ca（OH）2含量以及水化硅酸钙（C–S–H）凝胶的Ca/Si比（Ca和Si的摩尔比）的测定,研究复合胶凝材料体系中矿渣的水化特性。结果表明：在水泥–矿渣复合胶凝材料中,矿渣掺量越大,矿渣反应程度越低,但矿渣掺量≤70%时,对矿渣的反应程度影响不大。高温养护可提高早期矿渣的反应程度,但阻碍其后期的进一步水化。矿渣早期水化生成外部水化产物时消耗一定的Ca（OH）2,使硬化浆体中Ca（OH）2含量降低,矿渣水化吸收Ca（OH）2中的Ca2＋,使生成的C–S–H凝胶的Ca/Si比降低较少;在水化后期,矿渣生成内部水化产物不再消耗较多的Ca（OH）2,使C–S–H凝胶的Ca/Si比降低相对较多,硬化浆体中Ca（OH）2含量有增加的趋势,保证硬化浆体的长期稳定性。     

含有活性或惰性掺合料的复合胶凝材料硬化浆体的微观结构特征

用压汞法测定了不同温度条件下养护的含有粉煤灰或石英粉的复合胶凝材料硬化浆体的孔隙率.用扫描电镜观察了硬化浆体的微观形貌,同时测定了各种组成的复合胶凝材料的净浆强度.常温水化初期,活性与惰性矿物掺合料都只具有物理填充的作用,硬化浆体的孔隙率和强度由矿物掺合料的掺量所决定.高温水化条件下粉煤灰的火山灰反应提前发生.随水化龄期延长,粉煤灰逐渐发生火山灰反应,使硬化浆体结构密实,其强度逐步提高.活性与惰性矿物掺合料对复合胶凝材料浆体结构与性能的影响的差异在水化后期逐渐显现.     

高温养护下粉煤灰效应机理研究

大体积混凝土施工过程中,为降低水化热而采用大量的粉煤灰替代水泥,故对高掺量粉煤灰水泥的水化硬化机理进行深入系统的研究具有重要的意义.以大掺量粉煤灰胶凝材料硬化浆体为研究对象,结合XRD、FTIR、NMR等测试分析,研究高养护制度下粉煤灰掺量对其水化相C-S-H凝胶硅氧四面体聚合程度的影响规律.结果表明:高温养护的硬化浆体,其水化相C-S-H凝胶硅氧四面体聚合程度和Al原子取代Si原子的程度,在各个养护龄期始终高于常温养护的硬化浆体.     

等28d抗压强度条件下粉煤灰和矿渣对C50混凝土后期性能的影响

在28 d抗压强度相近的前提下,制备了纯水泥混凝土、大掺量粉煤灰混凝土、大掺量矿渣混凝土,测定了不同混凝土的后期抗压强度、抗氯离子渗透性,以及胶凝材料的化学结合水、硬化浆体中的Ca(OH)2含量.结果表明:含大掺量矿物掺合料的混凝土的后期强度和抗氯离子渗透性均明显高于纯水泥混凝土;大掺量矿渣混凝土的后期强度高于同掺量的大掺量粉煤灰混凝土;复合胶凝材料的后期水化程度增长率明显高于纯水泥;复合胶凝材料硬化浆体中后期Ca(OH)2含量明显低于纯水泥硬化浆体.     

电石渣激发矿渣-粉煤灰复合胶凝材料的作用机制

为探究矿渣、粉煤灰及电石渣的资源化利用,以电石渣作为碱激发剂,研究了矿渣-粉煤灰复合胶凝材料的水化产物组成及强度特征。采用X射线衍射(XRD)、傅里叶变换红外光谱(FTIR)、热重-差示扫描热(TG-DSC)、扫描电子显微镜及能谱(SEM-EDS)等微观测试技术,分析了复合胶凝材料的晶体结构、热化学性质以及微观形貌等特性,研究了电石渣激发矿渣-粉煤灰复合胶凝材料的作用机制。结果表明：电石渣作为碱激发剂时能为矿渣-粉煤灰复合胶凝材料提供初始水化所需要的强碱环境,驱动矿渣和粉煤灰发生水化反应。随着矿渣掺量的增加,复合胶凝材料的强度发展呈先增加后减小的变化趋势,在粉煤灰与矿渣掺量质量配比为4∶6、外掺电石渣质量分数为4%时,复合材料浆体经4 d常温养护+32 h高温蒸汽养护后抗压强度达到25.9 MPa;矿渣-粉煤灰复合胶凝体系中水化产物分布不均,主要组成为水化硅酸钙、水化铝酸钙、水化硅铝酸钙等凝胶。电石渣作为矿渣-粉煤灰体系的碱激发剂使用时效果良好。     

Insect antifeedant properties of anthranoids from the genusVismia

Vismiones and ferruginins, representatives of a new class of lypophilic anthranoids from the genusVismia were found to inhibit feeding in larvae of species ofSpodoptera, Heliothis, and inLocusta migratoria.     

Direct observation of freeze-thaw instability of latex coatings via high pressure freezing and cryogenic SEM

Despite its industrial importance, the subject of freeze-thaw (F/T) stability of latex coatings has not been studied extensively. There is also a lack of fundamental understanding about the process and the mechanisms through which a coating becomes destabilized. High pressure (2100 bar) freezing fixes the state of water-suspended particles of polymer binder and inorganic pigments without the growth of ice crystals during freezing that produce artifacts in direct imaging scanning electron microscopy (SEM) of fracture surfaces of frozen coatings. We show that by incorporating copolymerizable functional monomers, it is possible to achieve F/T stability in polymer latexes and in low-VOC paints, as judged by the microstructures revealed by the cryogenic SEM technique. Particle coalescence as well as pigment segregation in F/T unstable systems are visualized. In order to achieve F/T stability in paints, latex particles must not flocculate and should provide protection to inorganic pigment and extender particles. Because of the unique capabilities of the cryogenic SEM, we are able to separate the effects of freezing and thawing, and study the influence of the rate of freezing and thawing on F/T stability. Destabilization can be caused by either freezing or thawing. A slow freezing process is more detrimental to F/T stability than a fast freezing process; the latter actually preserves suspension stability during freezing. Presented at the 82nd Annual Meeting of the Federation of Societies for Coatings Technology, October 27–29, 2004 in Chicago, IL. Tied for first place in The John A. Gordon Best Paper Competition.     

Ethanol and (−)-α-Pinene: Attractant Kairomones for Bark and Ambrosia Beetles in the Southeastern US

In 2002–2004, we examined the flight responses of 49 species of native and exotic bark and ambrosia beetles (Coleoptera: Scolytidae and Platypodidae) to traps baited with ethanol and/or (−)-α-pinene in the southeastern US. Eight field trials were conducted in mature pine stands in Alabama, Florida, Georgia, North Carolina, and South Carolina. Funnel traps baited with ethanol lures (release rate, about 0.6 g/day at 25–28°C) were attractive to ten species of ambrosia beetles (Ambrosiodmus tachygraphus, Anisandrus sayi, Dryoxylon onoharaensum, Monarthrum mali, Xyleborinus saxesenii, Xyleborus affinis, Xyleborus ferrugineus, Xylosandrus compactus, Xylosandrus crassiusculus, and Xylosandrus germanus) and two species of bark beetles (Cryptocarenus heveae and Hypothenemus sp.). Traps baited with (−)-α-pinene lures (release rate, 2–6 g/day at 25–28°C) were attractive to five bark beetle species (Dendroctonus terebrans, Hylastes porculus, Hylastes salebrosus, Hylastes tenuis, and Ips grandicollis) and one platypodid ambrosia beetle species (Myoplatypus flavicornis). Ethanol enhanced responses of some species (Xyleborus pubescens, H. porculus, H. salebrosus, H. tenuis, and Pityophthorus cariniceps) to traps baited with (−)-α-pinene in some locations. (−)-α-Pinene interrupted the response of some ambrosia beetle species to traps baited with ethanol, but only the response of D. onoharaensum was interrupted consistently at most locations. Of 23 species of ambrosia beetles captured in our field trials, nine were exotic and accounted for 70–97% of total catches of ambrosia beetles. Our results provide support for the continued use of separate traps baited with ethanol alone and ethanol with (−)-α-pinene to detect and monitor common bark and ambrosia beetles from the southeastern region of the US.     

Methyl 2,4,6-decatrienoates Attract Stink Bugs and Tachinid Parasitoids

Halyomorpha halys (Stål) (Pentatomidae), called the brown marmorated stink bug (BMSB), is a newly invasive species in the eastern USA that is rapidly spreading from the original point of establishment in Allentown, PA. In its native range, the BMSB is reportedly attracted to methyl (E,E,Z)-2,4,6-decatrienoate, the male-produced pheromone of another pentatomid common in eastern Asia, Plautia stali Scott. In North America, Thyanta spp. are the only pentatomids known to produce methyl 2,4,6-decatrienoate [the (E,Z,Z)-isomer] as part of their pheromones. Methyl 2,4,6-decatrienoates were field-tested in Maryland to monitor the spread of the BMSB and to explore the possibility that Thyanta spp. are an alternate host for parasitic tachinid flies that use stink bug pheromones as host-finding kairomones. Here we report the first captures of adult and nymph BMSBs in traps baited with methyl (E,E,Z)-2,4,6-decatrienoate in central Maryland and present data verifying that the tachinid, Euclytia flava (Townsend), exploits methyl (E,Z,Z)-2,4,6-decatrienoate as a kairomone. We also report the unexpected finding that various isomers of methyl 2,4,6-decatrienoate attract Acrosternum hilare (Say), although this bug apparently does not produce methyl decatrienoates. Other stink bugs and tachinids native to North America were also attracted to methyl 2,4,6-decatrienoates. These data indicate there are Heteroptera in North America in addition to Thyanta spp. that probably use methyl 2,4,6-decatrienoates as pheromones. The evidence that some pentatomids exploit the pheromones of other true bugs as kairomones to find food or to congregate as a passive defense against tachinid parasitism is discussed.     

2007～2008年世界塑料工业进展

收集了2007年7月～2008年6月世界塑料工业的相关资料,介绍了2007～2008年国外塑料工业的发展情况,提供了世界塑料产量、消费量及全球各类树脂的需求量及产能情况.按通用热塑性树脂(聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂)、工程塑料(尼龙、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚)、特种工程塑料(聚苯·硫醚、液晶聚合物、聚醚醚酮)、通用热固性树脂(酚醛、聚氨酯、不饱和聚酯树脂、环氧树脂)不同品种的顺序,对树脂的产量、消费量、供需状况及合成工艺、产品应用开发、树脂品种的延伸及应用的进一步扩展等技术作了详细介绍.     

2005～2006年国外塑料工业进展

收集了2005年7月～2006年6月国外塑料工业的相关资料,介绍了2005—2006年国外塑料工业的发展情况。提供了世界塑料产量、消费量及全球各类树脂生产量以及各国塑料制品的进出口情况。作为对比,介绍了中国塑料的生产情况。按通用热塑性树脂（聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂）、工程塑料（聚酰胺、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚）、通用热固性树脂（酚醛、聚氨酯、不饱和树脂、环氧树脂）、特种工程塑料（聚苯硫醚、液晶聚合物、聚醚醚酮）的品种顺序,对树脂的产量、消费量、供需状况及合成工艺、产品开发、树脂品种的延伸及应用的扩展作了详细的介绍。