Nanorod-assembled spinel Li1.05Mn1.95O4 rods with a central tunnel along the rod-axis for high rate capability of rechargeable lithium-ion batteries

Nanorod-assembled spinel Li_1.05Mn_1.95O₄ rods with a central tunnel along the rod-axis were synthesized using highly crystalline β-MnO₂ rods as self-templates. The synthesized spinel Li_1.05Mn_1.95O₄ is an assembly of several single crystal-like nanorods with an average diameter and length of 100 and 400 nm, respectively, which was determined by microstructural Rietveld refinement using the synchrotron powder XRD data. Galvanostatic battery testing showed that central-tunneled and nanorod-assembled Li_1.05Mn_1.95O₄ rods have a high charge storage capacity at high current densities in comparison with those of the spinel rods without a tunnel structure and commercial powders. Moreover, a capacity retention value of ∼81% was observed at the end of 100 cycles at a current of 250 mAh g⁻¹.     

Improved pseudo-capacitive performance of manganese oxide films synthesized by the facile sol–gel method with iron acetate addition

Manganese oxide electrodes possessing pseudo-capacitance behaviors were successfully made with a simple sol–gel method. The experimental results showed that the specific capacitance was 101.2 F/g for pure manganese oxide films after annealing at 300 °C. However, the specific capacitance increased to 232.3 F/g with iron acetate (1.0 mol% Fe) addition and after annealing at 350 °C. The surface morphology observations revealed that the annealing temperature of 350 °C produced a higher surface area film with smaller pores. X-ray diffraction results showed that the manganese-iron oxide was composed of Mn₃O₄ and Mn₂O₃ phases, without iron oxide diffraction peaks. The manganese-iron oxide electrode with Mn₃O₄ and Mn₂O₃ phases exhibited good electrochemical performance and capacitance efficiency.     

Novel synthesis of layered LiNi1/2Mn1/2O2 as cathode material for lithium rechargeable cells

A new solution combustion synthesis of layered LiNi_0.5Mn_0.5O₂ involving the reactions of LiNO₃, Mn(NO₃)₂, NiNO₃, and glycine as starting materials is reported. TG/DTA studies were performed on the gel-precursor and suggest the formation of the layered LiNi_0.5Mn_0.5O₂ at low temperatures. The synthesized material was annealed at various temperatures, viz., 250, 400, 600, and 850 °C, characterized by means of X-ray diffraction (XRD) and reveals the formation of single phase crystalline LiNi_0.5Mn_0.5O₂ at 850 °C. The morphology of the synthesized material has been investigated by means of scanning electron microscopy (SEM) and suggests the formation of sub-micron particles. X-ray photoelectron spectroscopy (XPS) and cyclic voltammetry (CV) studies on the synthesized LiNi_0.5Mn_0.5O₂ powders indicate that the oxidation states of nickel and manganese are +2 and +4, respectively. Electrochemical galvanostatic charge-discharge cycling behavior of Li//LiNi_0.5Mn_0.5O₂ cell using 1 M LiPF₆ in EC/DMC as electrolyte exhibited stable capacities of ∼125 mAh/g in the voltage ranges 2.8-4.3 V and 3.0-4.6 V and is comparable to literature reports using high temperature synthesis route. The capacity remains stable even after 20 cycles. The layered LiNi_0.5Mn_0.5O₂ powders synthesized by this novel route have several advantages as compared to its conventional synthesis techniques.     

Lyothermal synthesis of nanocrystalline BaSnO3 powders

The synthesis of BaSnO₃ powders has been investigated at lyothermal conditions (temperature of 250 °C; t = 6 h), starting from SnO₂·xH₂O and Ba(OH)₂ and methanol, ethanol, isopropanol and acetone as solvents. Among them isopropanol was found to be the most suitable medium for preparing BaSnO₃. By addition of the modifier Genapol X-080 during the processing, the BET specific surface area of the end-powder was increased by a factor of 10. The as-prepared powder consisted of BaSn(OH)₆. The thermal behavior, the crystallization behavior and the structure evolution of the powder during heating treatment have been studied with the TG–DTA–MS, XRD and FTIR. The weight loss of the as-prepared powder of about 12 wt% heated up to 1200 °C is mainly attributed to the dehydration around 260 °C which leads to the structure rearrangement and the building of the [SnO₆] octahedra. At this temperature BaSn(OH)₆ converts to an amorphous phase, from which BaSnO₃ nucleates and grows with increasing temperature. The obtained BaSnO₃ powders had a BET specific surface area of 16.56 m²/g and a primary crystallite size of 49 nm.     

Electrochemical properties of nano- and micro-sized LiNi0.5Mn1.5O4 synthesized via thermal decomposition of a ternary eutectic Li-Ni-Mn acetate

Nano- and micro-sized LiNi_0.5Mn_1.5O₄ particles are prepared via the thermal decomposition of a ternary eutectic Li-Ni-Mn acetate. Lithium acetate, nickel acetate and manganese acetate can form a ternary eutectic Li-Ni-Mn acetate below 80 °C. After further calcination, nano-sized LiNi_0.5Mn_1.5O₄ particles can be obtained at an extremely low temperature (500 °C). When the sintering temperature goes above 700 °C, the particle size increases, and at 900 °C micro-sized LiNi_0.5Mn_1.5O₄ particles (with a diameter of about 4 μm) are obtained. Electrochemical tests show that the micro-sized LiNi_0.5Mn_1.5O₄ powders (sintered at 900 °C) exhibit the best capacity retention at 25 °C, and after 100 cycles, 97% of initial discharge capacity can still be reached. Nano-sized LiNi_0.5Mn_1.5O₄ powders (sintered at 700 °C) perform the best at low temperatures; when cycled at −10 °C and charged and discharged at a rate of 1 C, nano-sized LiNi_0.5Mn_1.5O₄ powders can deliver a capacity as high as 110 mAh g⁻¹.     

Spinel lithium manganese oxide synthesized under a pressurized oxygen atmosphere

Spinel lithium manganese oxide was synthesized via co-precipitation. The prepared lithium manganese oxide powder was further heated at 700 °C for 15 h under pressurized (3 bar) oxygen atmosphere. The resultant exhibited a highly crystalline cubic spinel phase with space group Fd3m, as confirmed by X-ray diffraction. The spinel compound exhibited a slightly smaller lattice constant than a conventional spinel compound, even though the cationic ratio of Li/Mn is the same for both compounds. Chemical titration of the Mn component showed that heat treatment under a 3 bar oxygen atmosphere resulted in slightly higher average Mn oxidation state, indicating that the amount of Mn⁴⁺ increased after the treatment. The Li_1.05Mn_1.95O_3.99 electrode exhibited improved cycling performance, namely, 96.3% of capacity retention during 100 cycles at elevated temperature (60 °C). The details of the structure and electrochemistry of the electrode are discussed.     

Synthesis of nanocrystalline Mn-Zn ferrite powders through thermolysis of mixed oxalates

Nanocrystalline Mn-Zn ferrite powders were synthesized by thermal decomposition of an oxalate precursor. Two polymorphs of a mixed Mn-Zn-Fe oxalate dihydrate were obtained by precipitation of metal ions with oxalic acid: monoclinic α-(Mn, Zn, Fe)₃(C₂O₄)₃·6H₂O is obtained after precipitation and ageing at 90 °C, whereas the orthorhombic β-type is formed after precipitation at room temperature. The morphology of the oxalate crystals can be controlled by the precipitation conditions. The α-polymorph of the mixed oxalate consists of prismatic and agglomerated particles. The β-oxalate forms non-agglomerated crystallites of submicron size. Thermal decomposition of the oxalate at 350 °C in air results in an amorphous product. Nanosize Mn-Zn ferrite powders are formed at 500 °C and a mixture of haematite and spinel is observed at 750 °C. The thermal decomposition of the mixed oxalate is monitored by thermal analysis, XRD and IR-spectroscopy. The morphology of the oxalate particles is preserved during thermal decomposition; the oxide particle aggregates display similar size and shape as the oxalates. The primary particles are much smaller; their size increases from 3 nm to 50 nm after decomposition of the oxalates at 350 and 500 °C, respectively. The powder synthesized by decomposition at 500 °C was sintered at 1150 °C to dense and fine-grained Mn-Zn ferrites.     

Improvement of electrochemical properties of LiNi0.5Mn1.5O4 spinel prepared by radiated polymer gel method

LiNi_0.5Mn_1.5O₄ as a 4.7 V-class cathode material was prepared through the radiated polymer gel method that allowed homogeneous mixing of starting materials at the atomic scale. After calcinations of the polymer gels containing the metal salts at different temperatures from 750 to 1150 °C, powders of a pure LiNi_0.5Mn_1.5O₄ phase were obtained. X-ray diffraction and transmission electron microscopy were used to characterize the structures of the powders. Galvanostatic cell cycling and a simultaneous DC resistance measurement were performed on Li/LiNi_0.5Mn_1.5O₄ cells. It is found that the powder calcined at 950 °C shows the best electrochemical performance with the initial discharge capacity of 139 mAh g⁻¹ and 96% retention after 50 cycles. Adopting a slow cooling procedure for the powder calcination can increase the capacity of LiNi_0.5Mn_1.5O₄ at the 4.7 V plateau. Besides, a “w”-shape change of the DC resistance of Li/LiNi_0.5Mn_1.5O₄ cells is a good indication of the structural change of LiNi_0.5Mn_1.5O₄ electrode during charge and discharge courses.     

Microstructure and ionic conductivity properties of gadolinia doped ceria (GdxCe1−xO2−x/2) electrolytes for intermediate temperature SOFCs prepared by the polyol method

Gd_0.1Ce_0.9O_1.95 and Gd_0.2Ce_0.8O_1.9 powders were prepared through the polyol process without using any protective agent. Microstructural and physical properties of the samples were characterized with X-ray diffraction (XRD), scanning electron microscopy (SEM), thermogravimetry (TG) and impedance analysis methods. The results of the thermogravimetry/differential thermal analysis (TG/DTA) and XRD indicated that a single-phase fluorite structure formed at the relatively low calcination temperature of 500 °C. The XRD patterns of the samples revealed that the crystallite size of the samples increased as calcination temperatures increased. The sintering behavior and ionic conductivity of pellets prepared from gadolinia doped ceria (GDC) powders, which were calcined at 500 °C, were also investigated. The relative densities of the pellets, which were sintered at temperatures above 1300 °C, were higher than 95%. The results of the impedance spectroscopy revealed that the GDC-20 sample that was sintered at 1400 °C exhibited an ionic conductivity of 3.25×10⁻² S cm⁻¹ at 800 °C in air. This result clearly indicates that GDC powder with adequate ionic conductivity can be prepared through the polyol process at low temperatures.     

Low temperature synthesis of nanocrystalline magnesium aluminate spinel by a soft chemical method

A new simple soft chemical method – synthesizing nanocrystalline MgAl₂O₄ spinel powder with oxalic acid as organic template and nitric acid as an oxidizing agent – is described. The method was developed with the objective of obtaining phase pure nanocrystalline MgAl₂O₄ spinel powder with uniform particle size and morphology at a much lower temperature than that used by conventional methods. The synthesized powders were characterized by X-ray diffractometry (XRD), thermogravimetry (TGA), Fourier transform infrared spectroscopy (FTIR), surface area analysis (BET) and field emission scanning electron microscopy (FE-SEM). The average crystallite size of the single phase material was 30 nm. Through this method, porous MgAl₂O₄ powder with a high surface area of 162.2 m²g⁻¹ and 141 m²g⁻¹ was obtained at 600 °C and 700 °C, respectively.     

Effect of synthesis condition on the structural and electrochemical properties of Li[Ni1/3Mn1/3Co1/3]O2 prepared by the metal acetates decomposition method

In order to get homogeneous layered oxide Li[Ni_1/3Mn_1/3Co_1/3]O₂ as a lithium insertion positive electrode material, we applied the metal acetates decomposition method. The oxide compounds were calcined at various temperatures, which results in greater difference in morphological (shape, particle size and specific surface area) and the electrochemical (first charge profile, reversible capacity and rate capability) differences. The Li[Ni_1/3Mn_1/3Co_1/3]O₂ powders were characterized by means of X-ray diffraction (XRD), charge/discharge cycling, cyclic voltammetry and SEM. XRD experiment revealed that the layered Li[Ni_1/3Mn_1/3Co_1/3]O₂ material can be best synthesized at temperature of 800 °C. In that synthesized temperature, the sample showed high discharge capacity of 190 mAh g⁻¹ as well as stable cycling performance at a current density of 0.2 mA cm⁻² in the voltage range 2.3-4.6 V. The reversible capacity after 100 cycles is more than 190 mAh g⁻¹ at room temperature.     

Synthesis and characterization of nanocrystalline forsterite through citrate–nitrate route

Nanocrystalline forsterite, Mg₂SiO₄, powder was synthesized according to the citrate–nitrate technique using an aqueous solution of magnesium nitrate, colloidal silica, citric acid, and ammonia. The dried precursor and the powders calcined at different temperatures were characterized by X-ray diffraction (XRD), simultaneous thermal analysis (STA), field emission scanning electron microscopy (FE-SEM), and transmission electron microscopy (TEM). The initial crystallization temperature of forsterite was around 770 °C while fully crystallized forsterite was obtained at 860 °C with a crystallite size of about 30 nm.     

Low-temperature solution combustion synthesis of high performance LiNi0.5Mn1.5O4

High-voltage LiNi_0.5Mn_1.5O₄ spinels were synthesized by a low temperature solution combustion method at 400 °C, 600 °C and 800 °C for 3 h. The phase composition, structural disordering, micro-morphologies and electrochemical properties of the products were investigated by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscope (SEM) and constant current charge–discharge test. XRD analysis indicated that single phase LiNi_0.5Mn_1.5O₄ powders with disordered Fd-3m structures were obtained by the method at 400 °C, 600 °C and 800 °C. The crystallinity increased with increasing preparation temperatures. XRD and FTIR data indicated that the degree of structural disordering in the product prepared at 800 °C was the largest and in the product prepared at 600 °C was the least. SEM investigation demonstrated that the particle size and the crystal perfection of the products were increased with increasing temperatures. The particles of the product prepared at 600 °C with ~200 nm in size are well developed and homogeneously distributed. Charge/discharge curves and cycling performance tests at different current density indicated that the product prepared at 600 °C had the largest specific capacity and the best cycling performance, due to its high purity, high crystallinity, small particle size as well as moderate amount of Mn³⁺ ions.     

Synthesis and characterization of high-density non-spherical Li(Ni1/3Co1/3Mn1/3)O2 cathode material for lithium ion batteries by two-step drying method

Non-spherical Li(Ni_1/3Co_1/3Mn_1/3)O₂ powders have been synthesized using a two-step drying method with 5% excess LiOH at 800 °C for 20 h. The tap-density of the powder obtained is 2.95 g cm⁻³. This value is remarkably higher than that of the Li(Ni_1/3Co_1/3Mn_1/3)O₂ powders obtained by other methods, which range from 1.50 g cm⁻³ to 2.40 g cm⁻³. The precursor and Li(Ni_1/3Co_1/3Mn_1/3)O₂ are characterized by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and scanning electron microscope (SEM). XPS studies show that the predominant oxidation states of Ni, Co and Mn in the precursor are 2⁺, 3⁺ and 4⁺, respectively. XRD results show that the Li(Ni_1/3Co_1/3Mn_1/3)O₂ material obtained by the two-step drying method has a well-layered structure with a small amount of cation mixing. SEM confirms that the Li(Ni_1/3Co_1/3Mn_1/3)O₂ particles obtained by this method are uniform. The initial discharge capacity of 167 mAh g⁻¹ is obtained between 3 V and 4.3 V at a current of 0.2 C rate. The capacity of 159 mAh g⁻¹ is retained at the end of 30 charge-discharge cycle with a capacity retention of 95%.     

Thermal conductivity of combustion synthesized β-sialons

To the first time, thermal conductivities of spark plasma sintered β-sialons (Si₃Al₃O₃N₅) procured from combustion synthesis (CS) with no sintering additive were measured by the laser flash method at room temperature. A full densification occurred when these materials were sintered at 1600 °C with a simultaneous pressure of 50 MPa. XRD analyses indicated that single phase β-sialons were formed after SPS though the combustion synthesized β-sialon powders had considerable amounts of silicon impurities. Thermal conductivity values increased with sintering temperature and attained a maximum of 5.49 W m⁻¹ K⁻¹ for fully densified β-sialons sintered at 1700 °C for 10 min.     

X-ray absorption spectroscopy studies of nickel oxide thin film electrodes for supercapacitors

Nickel oxide films were synthesized by electrochemical precipitation of Ni(OH)₂ followed by heat-treatment in air at various temperatures (200-600 °C). Their structure and electrochemical properties were studied by cyclic voltammetry, X-ray diffraction (XRD) and X-ray absorption spectroscopy (XAS). XRD results showed that the nickel oxide obtained at 250 °C or above has a crystalline NiO structure. The specific capacitance of the oxide depends on the heat-treatment temperature, showing a maximum value at 300 °C. XAS results revealed that the non-stoichiometric nickel oxide (Ni_1−xO) approached the stoichiometric NiO structure with increasing heat-treatment temperature due to the defect healing effect. The defective nature of the nickel oxide could be utilized to improve its specific capacitance for supercapacitor application.     

Li-intercalation behaviour of vanadium oxide thin film prepared by thermal oxidation of vanadium metal

In order to produce thin films of crystalline V₂O₅, vanadium metal was thermally oxidised at 500 °C under oxygen pressures between 250 and 1000 mbar for 1-5 min. The oxide films were characterised by X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), X-ray diffraction (XRD) and Rutherford backscattering spectrometry (RBS). The lithium intercalation performance of the oxide films was investigated by cyclic voltammetry (CV), chronopotentiometry and electrochemical impedance spectroscopy (EIS). It was shown that the composition, the crystallinity and the related lithium intercalation properties of the thin oxide films were critically dependent on the oxidation conditions. The formation of crystalline V₂O₅ films was stimulated by higher oxygen pressure and longer oxidation time. Exposure for 5 min at 750 mbar O₂ at 500 °C resulted in a surface oxide film composed of V₂O_5, and consisting of crystallites up to 200 nm in lateral size. The thickness of the layer was about 100 nm. This V₂O₅ oxide film was found to have good cycling performance in a potential window between 3.8 and 2.8 V, with a stable capacity of 117 ± 10 mAh/g at an applied current density of 3.4 μA/cm². The diffusion coefficients corresponding to the two plateaus at 3.4 and 3.2 V were determined from the impedance measurements to (5.2 and 3.0) × 10⁻¹³ cm² s⁻¹, respectively. Beneath the V₂O₅ layer, lower oxides (mainly VO₂) were found close to the metal. At lower oxygen pressure and shorter exposure times, the oxide films were less crystalline and the amount of V⁴⁺ increased in the surface oxide film, as revealed by XPS. At intermediate oxygen pressures and exposure times a mixture of crystalline V₂O₅ and V₆O₁₃ was found in the oxide film.     

Morphological and electrochemical properties of LiV3O8 cathode powders prepared by spray pyrolysis

Lithium trivanadate (LiV₃O₈) powders are prepared by spray pyrolysis. The precursor powders of LiV₃O₈ obtained by spray pyrolysis have spherical and rod-like morphologies. The LiV₃O₈ powders post-treated at 300 °C and 400 °C also have spherical and rod-like morphologies. However, the LiV₃O₈ cathode powders post-treated at 500 °C consist of only rod-like crystals. The crystalline structure of the precursor powders that were directly prepared by spray pyrolysis comprised of LiV₃O₈ layers along with a small amount of β-Li_0.33V₂O₅ impurity. The peak due to β-Li_0.33V₂O₅ persisted in the XRD spectrum even after post-treatment at 300 °C. On the other hand, crystalline structures of the powders post-treated at 400 °C and 500 °C comprised pure LiV₃O₈ layers. The initial discharge capacities of the LiV₃O₈ cathode powders decrease from 344 mAh g⁻¹ to 261 mAh g⁻¹ when the post-treatment temperatures increase from 300 °C to 500 °C. The discharge capacities of the LiV₃O₈ cathode powders obtained after post-treatment at 400 °C and 500 °C are approximately 255 mAh g⁻¹ and 236 mAh g⁻¹, respectively, after 40 cycles.     

Effect of the addition ZrO2–Al2O3 on nanocrystalline hydroxyapatite bending strength and fracture toughness

Nanocrystalline hydroxyapatite powder has been synthesized from a Ca(NO₃)₂·4H₂O and (NH₄)₂HPO₄ solution by the precipitation method. In the next step we prepared ZrO₂–Al₂O₃ powder. After preparation, the powder was dried at 80 °C and calcined at 1200 °C for 1 h. Various amounts (HAP–15 wt% ZA, HAP–30 wt% ZA) of powder were mixed with the hydroxyapatite by ball milling. The powder mixtures were pressed and sintered at 1000 °C, 1100 °C and 1200 °C for 1 h. In order to study the structural evolution, X-ray diffraction (XRD) was used. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) were used to estimate the particle size of the powder and observe fracture surfaces. Results show that the bending strength of pressed nanocrystalline HAP was improved significantly by the addition 15 wt% of ZrO₂–Al₂O₃ powders at 1200 °C, but the fracture toughness was not changed, however when 30 wt% of ZA powders were added to nanocrystalline HAP, the bending strength and fracture toughness of the specimens decreased at all sintering temperature.     

Synthesis of self-organized mixed oxide nanotubes by sonoelectrochemical anodization of Ti-8Mn alloy

Self ordered arrays of titanium manganese mixed oxide nanotubes were prepared by anodization of Ti8Mn alloy (UNS R56080) under ultrasonication in diluted ethylene glycol containing fluoride. The dimensions of the nanotubes (diameter: 20-100 nm and length: 0.5-2.0 μm) could be tuned by changing the synthesis parameters. The as-anodized nanotubes showed a stoichiometry of (Ti,Mn)O₂. Upon annealing at 500 °C in oxygen atmosphere, the nanotubes contained a mixture of anatase + rutile phases of TiO₂ and Mn₂O₃. The composition of the oxide nanotubes was influenced by the chemistry of the phases present in the alloy. More manganese content was observed in the oxide formed on the β-phase than in the oxide layer of α-phase. Anodization in the ultrasonic field increased the kinetics of nanotubular oxide formation and resulted in homogeneous ordering of the nanotubular arrays as compared to the anodization by conventional stirring in the fluoride containing ethylene glycol solution. Whereas, anodization in aqueous acidified fluoride solutions resulted in severe attack of the β-phase and did not show presence of nanotubular oxide structure.