Photocatalytic hydrogen production under direct solar light in a CPC based solar reactor: Reactor design and preliminary results

In despite of so many types of solar reactors designed for solar detoxification purposes, few attempts have been made for photocatalytic hydrogen production, which in our option, is one of the most promising approaches for solar to chemical energy conversion. Addressing both the similarity and dissimilarity for these two processes and by fully considering the special requirements for the latter reaction, a Compound Parabolic Concentrator (CPC) based photocatalytic hydrogen production solar reactor has been designed for the first time. The design and optimization of this CPC based solar reactor has been discussed in detail. Preliminary results demonstrated that efficient photocatalytic hydrogen production under direct solar light can be accomplished by coupling tubular reactors with CPC concentrators. It is anticipated that this first demonstration of concentrator-based solar photocatalytic hydrogen production would draw attention for further studies in this promising direction.     

A miniature concentrating photovoltaic and thermal system

A novel miniature concentrating PV (MCPV) system is presented and analyzed. The system is producing both electrical and thermal energy, which is supplied to a nearby consumer. In contrast to PV/thermal (PV/T) flat collectors, the heat from an MCPV collector is not limited to low-temperature applications. The work reported here refers to the evaluation and preliminary design of the MCPV approach. The heat transport system, the electric and thermal performance, the manufacturing cost, and the resulting cost of energy in case of domestic water heating have been analyzed. The results show that the new approach has promising prospects.     

ICS solar systems with two water tanks

Integrated collector storage (ICS) systems are compact solar water heaters, simple in construction, installation and operation. They are cheaper than flat plate thermosiphonic units, but their higher thermal losses make them suitable mainly for application in locations with favourable weather conditions. Aiming to the achievement of low system height and satisfactory water temperature stratification, new types of ICS systems with two horizontal cylindrical storage tanks, properly mounted in stationary CPC reflector troughs are suggested. The non-uniform distribution of solar radiation on the two absorbing surfaces is combined with the seasonal sun elevation, resulting to effective water heating. In addition, the inverted absorber concept design can be applied to ICS systems with two storage tanks. In this paper, we present the design and performance of double tank ICS solar systems, which are based on the combination of symmetric and asymmetric CPC reflectors with water storage tanks. The analytical equations of the collector geometry of all models are calculated with respect to the radius of the cylindrical water storage tank and the reflector rim angles. Experimental results for the variation of the water temperature inside storage tanks, the mean daily efficiency and the coefficient of thermal losses during night are given for all experimental models. The tests were performed without water draining and the results show that the double tank ICS systems are efficient in water temperature rise during day and satisfactory preservation of the hot water temperature during night, with the upper storage tank being more effective in performance in most of the studied models.     

Integrated collector storage solar systems with asymmetric CPC reflectors

New types of ICS solar systems were designed and outdoor tests of experimental models were performed. The systems consist of single cylindrical horizontal water storage tanks placed inside stationary truncated asymmetric CPC reflector troughs of different design. We used high emittance absorber surface, low cost curved reflectors, iron oxide glazing and thermal insulation at the non illuminated tank surfaces, aiming towards cost effective ICS systems with satisfactory heat preservation during the night. Four experimental models of different designs were constructed and tested to determine their performance regarding their mean daily efficiency and thermal losses during the night. The new ICS systems were compared to an ICS system with symmetric CPC reflectors of similar construction and dimensions and also to a typical Flat Plate Thermosiphonic Unit (FPTU). Test results showed that the ICS systems with asymmetric CPC reflectors present almost the same mean daily efficiency and better preservation of hot water temperature during the night, compared to the ICS system with the symmetric CPC reflectors. The comparison with the FPTU system confirmed the satisfied daily operation of all ICS systems and their moderate storage heat preservation during the night. Theoretical results showed acceptable thermal performance of all ICS systems regarding annual operation.     

Energy management in solar thermal power plants with double thermal storage system and subdivided solar field

In the paper, two systems for solar thermal power plants (STPPs) are devised for improving the overall performance of the plant. Each one attempts to reduce losses coming from two respective sources. The systems are simulated and compared to a reference STPP.     

Integrated solar collector–storage tank system with thermal diode

Water heating by utilizing solar energy for domestic use is a well established technique. However, most systems consist of the solar collector and storage tank as separate units and require piping and extra thermal insulation for both. This work considers an integrated system, which is easy to manufacture or to modify the storage tank to operate as a solar collector as well as a storage tank. The system contains a thermal diode to prevent reverse circulation at night-time. A prototype is constructed and a mathematical model is developed to study the thermal performance of the integrated system. It is found that the thermal efficiency of the suggested system is comparable with conventional systems. Also, simulation indicated that the thermal diode significantly reduces heat losses at night-time.     

Performance model for parabolic trough solar thermal power plants with thermal storage: Comparison to operating plant data

This paper describes a simulation model that reproduces the performance of parabolic trough solar thermal power plants with a thermal storage system. The aim of this model is to facilitate the prediction of the electricity output of these plants during the various stages of their planning, design, construction and operation. Model results for a 50 MW_e power plant are presented and compared to real data from an equivalent power plant currently operated by the ACS Industrial Group in Spain.     

Heat transfer in a conical cavity calorimeter for measuring thermal power of a point focus concentrator

A theoretical study of the heat transfer process that takes place in a special calorimeter of conical cavity named CAVICAL is presented. This instrument is used to measure the thermal power of a point focus solar concentrator system named DEFRAC, developed at the Center for Energy Research of the National University of Mexico. The DEFRAC concentrator has a power of 1.3 kWth and a very fine optical system. The calorimeter has a cavity opening of 8.24 cm². A detailed heat transfer study was done using FLUENT code. The heat transfer processes taken into account for the analysis were the radiative energy absorbed by the inner cavity wall, the energy transfer from the outer cavity wall to the air by natural convection, the energy transferred by conduction through the inner metallic wall of the calorimeter, and by forced convection to the fluid in the cooling system. The calorimetric information gathered allowed determining the thermal power that the concentrator is able to capture. Temperature and velocity fields have been calculated for each of the thermal fluids considered inside of the calorimeter. The analysis gave thermal losses and measured the thermal efficiency of the device. The information generated is useful to further optimize the design of the calorimeter.     

Heat transfer analysis of parabolic trough solar receiver

Solar Parabolic Trough Collectors (PTCs) are currently used for the production of electricity and applications with relatively higher temperatures. A heat transfer fluid circulates through a metal tube (receiver) with an external selective surface that absorbs solar radiation reflected from the mirror surfaces of the PTC. In order to reduce the heat losses, the receiver is covered by an envelope and the enclosure is usually kept under vacuum pressure. The heat transfer and optical analysis of the PTC is essential to optimize and understand its performance under different operating conditions. In this paper a detailed one dimensional numerical heat transfer analysis of a PTC is performed. The receiver and envelope were divided into several segments and mass and energy balance were applied in each segment. Improvements either in the heat transfer correlations or radiative heat transfer analysis are presented as well. The partial differential equations were discretized and the nonlinear algebraic equations were solved simultaneously. Finally, to validate the numerical results, the model was compared with experimental data obtained from Sandia National Laboratory (SNL) and other one dimensional heat transfer models. Our results showed a better agreement with experimental data compared to other models.     

ICS solar systems with horizontal (E–W) and vertical (N–S) cylindrical water storage tank

The use of a horizontal cylindrical water storage tank contributes to pressure resistant, low height and efficient ICS solar systems. These systems can satisfactorily achieve water heating when the cylindrical storage tank is combined with stationary CPC or involute type curved reflectors. The diameter of the cylindrical storage tank determines the length of the reflectors, the system depth and the ratio of the stored water per aperture area. In these solar systems the storage tank can be partially thermally insulated to suppress thermal losses from it to the ambience. We constructed four experimental models with truncated symmetric CPC reflectors, two with 90° and other two with 60° of acceptance angle, half of them without and half with a 1/4 thermally insulated storage tank cylindrical surface. In addition, we constructed two ICS systems with involute reflectors, with acceptance angle 180°, one without and the other one with a 1/4 thermally insulated storage tank. The six ICS systems were tested under the same weather conditions and without water drain, to determine their stored water temperature variation, mean daily efficiency and thermal losses during night. The results showed that CPC reflectors contribute to efficient operation of systems day and night, while involute reflectors mainly to the water heat preservation during night.     

Experimental investigation of concentrated solar air-heater with internal multiple-fin array

This paper presents the results of experimental validation of energy conversion in a concentrated solar air-heater with internal multiple-fin array. A novel high temperature solar air heater was proposed to convert solar energy to heat for space heating in climatic conditions of Poland.The aim of the study was to verify the previously created mathematical model of heat transfer processes. The collector’s performance was analysed experimentally against the reduced temperature difference. During the experiments, an electrical air heater was used to change the air temperature at the inlet of the receiver according to the test demands. Additionally, two daily performance evaluation tests were done. During the tests the all-day measured data was collected automatically and recorded at 1-min intervals. Hourly and daily thermal efficiency was calculated. Validation of the model showed its correctness and proved that the model can be accepted.     

Heat and mass transfer in a flat plate solar solid adsorption refrigeration ice maker

A uniform pressure model is presented to describe the heat and mass transfer in an adsorbent bed for a flat plate solar ice maker. This model accounts for heat and mass transfer in a porous bed in a two-dimensional transient process. An experiment has been conducted to validate this model and the calculated results are in good agreement with experiments. With the help of this model, the transient analysis and performance prediction of an intermittent solar powered solid refrigerator can be presented.     

A novel solar bi-ejector refrigeration system and the performance of the added injector with different structures and operation parameters

A novel solar bi-ejector refrigeration system was investigated, whose difference compared to the traditional system is that the circulation pump is replaced by a thermal injector. The new system works more stably and needs less maintenance work than the old one, and the whole system can more fully utilize the solar energy. The mathematical models for calculating the performance of the injector and the whole solar refrigeration system were established. The pressure rise performance of injector under different structure and operation parameters and the performance of solar bi-ejector refrigeration system were studied with R123. The results show that the discharged pressure of injector is affected by structure dimensions of injector and operation conditions. With increasing generation temperature, the entrainment ratio of ejector becomes better while that of injector becomes worse and the overall thermal efficiency of the solar bi-ejector refrigeration system first increases and then decreases with an optimum value of 0.132 at generation temperature of 105 °C, condensation temperature of 35 °C and evaporation temperature of 10 °C.     

A parabolic dish/AMTEC solar thermal power system and its performance evaluation

This paper proposes a parabolic dish/AMTEC solar thermal power system and evaluates its overall thermal–electric conversion performance. The system is a combined system in which a parabolic dish solar collector is cascaded with an alkali metal thermal to electric converter (AMTEC) through a coupling heat exchanger. A separate type heat-pipe receiver is selected to isothermally transfer the solar energy from the collector to the AMTEC. To assess the system’s overall thermal–electric conversion performance, a theoretical analysis has been undertaken in conjunction with a parametric investigation by varying relevant parameters, i.e., the average operating temperature and performance parameters associate with the dish collector and the AMTEC. Results show that the overall conversion efficiency of parabolic dish/AMTEC system could reach up to 20.6% with a power output of 18.54 kW corresponding to an operating temperature of 1280 K. Moreover, it is found that the optimal condenser temperature, corresponding to the maximum overall efficiency, is around 600 K. This study indicates that the parabolic dish/AMTEC solar power system exhibits a great potential and competitiveness over other solar dish/engine systems, and the proposed system is a viable solar thermal power system.     

Enhancing the thermal efficiency of solar ponds by extracting heat from the gradient layer

An alternative method of heat extraction from salinity-gradient solar ponds is investigated with the aim of increasing the overall energy efficiency of collecting solar radiation, storing heat and delivering this heat to an application. In this alternative method, heat is extracted from the non-convecting gradient layer of a solar pond as well as, or instead of, from the lower convective zone (LCZ). A theoretical analysis of combined gradient-layer and LCZ heat extraction is conducted to obtain expressions for the variation of temperature with depth in the pond, and the temperature gradient with depth. The dependence of the overall energy efficiency of the pond on thickness of the gradient-layer, temperature of delivered heat, and various combinations of gradient layer and LCZ heat extraction rates, including the limiting cases of gradient-layer heat extraction only, and LCZ heat extraction only, is then explored. This theoretical analysis suggests that heat extraction from the gradient layer has the potential to increase the overall energy efficiency of a solar pond delivering heat at a relatively high temperature by up to 50%, compared with the conventional method of heat extraction solely from the LCZ. The potential gain in efficiency using gradient-layer heat extraction is attributed to the lowering of heat losses by conduction to the upper convective (surface) zone that can be achieved with this method. Experimental investigations are proposed to test the predictions of the theoretical analysis in practice, and assess the impact of a number of idealized assumptions made on the findings reported here.     

A detailed nonuniform thermal model of a parabolic trough solar receiver with two halves and two inactive ends

In this paper a detailed one dimensional nonuniform thermal model of a parabolic trough solar collector/receiver is presented. The entire receiver is divided into two linear halves and two inactive ends for the nonuniform solar radiation, heat transfers and fluid dynamics. Different solar radiation and heat transfer modes can be taken into consideration for these four different regions respectively. This enables the study of different design parameters, material properties, operating conditions, fluid flow and heat transfer performance for the corresponding regions or the whole receiver. Then the nonuniform model and the corresponding uniform thermal model are validated with known performance of an existing parabolic trough solar collector/receiver. For applications, the uniform thermal model can be used to quickly compute the integral heat transfer performance of the whole PTC system while the nonuniform thermal model can be used to analyze the local nonuniform solar radiation and heat transfer performance characteristics and nonuniform heat transfer enhancements or optimizations. Later, it could also be effectively used with an intelligent optimization, such as the genetic algorithm or the particle swarm optimization, to quickly evaluate and optimize the characteristics and performance of PTCs under series of nonuniform conditions in detail.     

A concentrator module of spherical Si solar cell

Spherical Si solar cell, which is made up of Si spheres with a diameter of approximately 1.0 mm, is expected to be a promising candidate for low consumption of Si feedstock and simple process technology. This paper describes the formation process and the structure of a concentrator module in detail. The concentrator lens was formed by casting with ultraviolet light hardening resin. The concentration ratio was 4.4 times and the pitch between the spheres was 2.0 mm. By this module design, it was possible to realize a consumption of the Si feedstock of about 3.0 g/W. Conversion efficiencies of 11.3% from single-sphere cell, 8.5% from a 23-spheres module and 5.2% from a 105-spheres module under AM1.5, 100 mW/cm² illumination were achieved.     

A two dimensional thermal network model for a photovoltaic solar wall

A two dimensional thermal network model is proposed to predict the temperature distribution for a section of photovoltaic solar wall installed in an outdoor room laboratory in Concordia University, Montréal, Canada. The photovoltaic solar wall is constructed with a pair of glass coated photovoltaic modules and a polystyrene filled plywood board as back panel. The active solar ventilation through a photovoltaic solar wall is achieved with an exhaust fan fixed in the outdoor room laboratory. The steady state thermal network nodal equations are developed for conjugate heat exchange and heat transport for a section of a photovoltaic solar wall. The matrix solution procedure is adopted for formulation of conductance and heat source matrices for obtaining numerical solution of one dimensional heat conduction and heat transport equations by performing two dimensional thermal network analyses. The temperature distribution is predicted by the model with measurement data obtained from the section of a photovoltaic solar wall. The effect of conduction heat flow and multi-node radiation heat exchange between composite surfaces is useful for predicting a ventilation rate through a solar ventilation system.     

Effect of using nanofluids on efficiency of parabolic trough collectors in solar thermal electric power plants

In this paper, forced convection heat transfer nanofluid flow inside the receiver tube of solar parabolic trough collector is numerically simulated. Computational Fluid Dynamics (CFD) simulations are carried out to study the influence of using nanofluid as heat transfer fluid on thermal efficiency of the solar system. The three-dimensional steady, turbulent flow and heat transfer governing equations are solved using Finite Volume Method (FVM) with the SIMPLEC algorithm. The results show that the numerical simulation are in good agreement with the experimental data. Also, the effect of various nanoparticle volume fraction on thermal and hydrodynamic characteristics of the solar parabolic collector is discussed in details. The results indicate that, using of nanofluid instead of base fluid as a working fluid leads to enhanced heat transfer performance. Furthermore, the results reveal that by increasing of the nanoparticle volume fraction, the average Nusselt number increases.     

Modelling and performance study of a continuous adsorption refrigeration system driven by parabolic trough solar collector

This article suggests a numerical study of a continuous adsorption refrigeration system consisting of two adsorbent beds and powered by parabolic trough solar collector (PTC). Activated carbon as adsorbent and ammonia as refrigerant are selected. A predictive model accounting for heat balance in the solar collector components and instantaneous heat and mass transfer in adsorbent bed is presented. The validity of the theoretical model has been tested by comparison with experimental data of the temperature evolution within the adsorber during isosteric heating phase. A good agreement is obtained. The system performance is assessed in terms of specific cooling power (SCP), refrigeration cycle COP (COP_cycle) and solar coefficient of performance (COP_s), which were evaluated by a cycle simulation computer program. The temperature, pressure and adsorbed mass profiles in the two adsorbers have been shown. The influences of some important operating and design parameters on the system performance have been analyzed.The study has put in evidence the ability of such a system to achieve a promising performance and to overcome the intermittence of the adsorption refrigeration systems driven by solar energy. Under the climatic conditions of daily solar radiation being about 14 MJ per 0.8 m² (17.5 MJ/m²) and operating conditions of evaporating temperature, T_ev = 0 °C, condensing temperature, T_con = 30 °C and heat source temperature of 100 °C, the results indicate that the system could achieve a SCP of the order of 104 W/kg, a refrigeration cycle COP of 0.43, and it could produce a daily useful cooling of 2515 kJ per 0.8 m² of collector area, while its gross solar COP could reach 0.18.