Microstructure and mechanical properties of Al2O3/Y3Al5O12/ZrO2 ternary eutectic materials

Directionally solidified fibers and rods have been grown from the ternary Al₂O₃/Y₃Al₅O₁₂/ZrO₂ system using micro-pulling-down method. Fiber diameter could be varied 0.3 mm–2 mm at pull-rates ranging 6–900 mm/h and 500 mm in length. The ternary eutectic fibers had homogeneous colony patterned eutectic microstructures. The interlamellar spacing λ exhibited an inverse-square-root dependence on the growth speed v according to λ = 8 × v^−1/2, where λ has the dimension of μm and v is in μm/s. The tensile strength was recorded 1730 MPa at 25 °C and 1100 MPa at 1200 °C for a fiber crystals grown at a growth speed of 900 mm/h. Eutectic rods having 5 mm of diameter and up to 80 mm in length were also successfully grown by the micro-pulling-down method. The eutectic rods showed 1400 MPa of mechanical strength by compressive mode at 1500 °C with homogeneous colony microstructures.     

Microstructure of the directionally solidified ternary eutectic ceramic Al2O3/MgAl2O4/ZrO2

The directionally solidified Al₂O₃/MgAl₂O₄/ZrO₂ ternary eutectic ceramic was prepared via induction heating zone melting. Smooth Al₂O₃/MgAl₂O₄/ZrO₂ eutectic ceramic rods with diameters of 10 mm were successfully obtained. The results demonstrate that the eutectic rods consist of Al₂O₃, MgAl₂O₄ and ZrO₂ phases. In the eutectic microstructure, the MgAl₂O₄ and Al₂O₃ phases form the matrix, the ZrO₂ phase with a fibre or shuttle shape is embedded in the matrix, and a quasi-regular eutectic microstructure formed, presenting a typical in situ composite pattern. During the eutectic growth, the ZrO₂ phase grew on non-faceted phases ahead of the matrix growing on the faceted phase. The hardness and fracture toughness of the eutectic ceramics reached 12 GPa and 6.1 MPa·m ^1/2, respectively, i.e., two times and 1.7 times the values of the pre-sintered ceramic, respectively. In addition, the ZrO₂ phase in the matrix reinforced the matrix, acting as crystal whiskers to reinforce the sintered ceramic.     

Mechanical properties up to 1900 K of Al2O3/Er3Al5O12/ZrO2 eutectic ceramics grown by the laser floating zone method

Directionally solidified Al₂O₃–Er₃Al₅O₁₂–ZrO₂ eutectic rods were processed using the laser floating zone method at growth rates of 25, 350 and 750 mm/h to obtain microstructures with different domain size. The mechanical properties were investigated as a function of the processing rate. The hardness, ∼15.6 GPa, and the fracture toughness, ∼4 MPa m^1/2, obtained from Vickers indentation at room temperature were practically independent of the size of the eutectic phases. However, the flexural strength increased as the domain size decreased, reaching outstanding strength values close to 3 GPa in the samples grown at 750 mm/h. A high retention of the flexural strength was observed up to 1500 K in the materials processed at 25 and 350 mm/h, while superplastic behaviour was observed at 1700 K in the eutectic rods solidified at the highest rate of 750 mm/h.     

Growth of Al2O3/ZrO2(Y2O3) eutectic rods by the laser floating zone technique: effect of the rotation

The laser floating zone technique has been applied to the growth of Al₂O₃/ZrO₂(Y₂O₃) rods in the eutectic composition to reveal the effect of forced convection induced by rotation on the rod microstructure. A systematic experimental study of this effect has been carried out combining different source rod and/or eutectic rod rotation (0–200 rpm) and travelling speeds (10–1500 mm/h) in an axial thermal gradient close to 6 × 10⁵ C/m. The results indicate that the rotation is useful to achieve a more homogeneous temperature distribution, especially in thick rods but it has a limited effect in the change of the solidification front shape. The forced convection in the floating zone caused by rotation slightly flattens the solidification interface enhancing the homogeneity of the phase distribution across the sample. However, it introduces several new microstructural features like banding and phase coarsening that can deteriorate the mechanical behaviour of the rods. On the other hand, rods above 1.6 mm in diameter cannot be grown without cracks, even with fast eutectic rod rotation. Rotation does not change the pulling rate threshold (50 mm/h) at which the transition from coupled to dendritic and cellular growth morphology takes place.     

Synthesis and characterization of a MgO-MgAl2O4-ZrO2 composite with a continuous network microstructure

Using analytically pure MgO, analytically pure Al₂O₃ and analytically pure ZrO₂ as raw materials, Mg_4.68Al_2.64Zr_1.68O₁₂ was prepared at 1993 K for 10 h, and then, a MgO-MgAl₂O₄-ZrO₂ composite with a continuous network was successfully obtained by controlling the cooling rate based on the in-situ decomposition reaction of Mg_4.68Al_2.64Zr_1.68O₁₂ at temperatures below 1887 K. The three phases of MgO, MgAl₂O₄ and ZrO₂ are highly dispersed in this continuous network microstructure, with ZrO₂ intertwined by MgO and MgAl₂O₄ and micropores with a size of less than 2 µm. Furthermore, the synthesis mechanism of Mg_4.68Al_2.64Zr_1.68O₁₂ is given as follows: first, MgAl₂O₄ is synthesized using the reaction: MgO(s)+Al₂O₃(s)=MgAl₂O₄(s) at temperatures below 1894 K; and then, Mg_4.68Al_2.64Zr_1.68O₁₂ is further prepared through MgO and ZrO₂ diffusion and dissolution into MgAl₂O₄ at temperatures above 1894 K, for example, at 1923 K or 1993 K in this work.     

Growth-microstructure relationship in MgO-MgAl2O4 eutectic fabricated by micro-pulling down method with MgAl2O4 seed crystals

The MgO-MgAl₂O₄ eutectic was directionally solidified via micro-pulling down method in the form of rods with 2–3 mm diameter. MgAl₂O₄ single crystals (with <111> orientation) were used as crystallization seeds. At low pulling rates, especially 0.15 mm/min triangle-like cross-section was observed, which was linked to the eutectic MgAl₂O₄ following the crystallographic direction of the seed. MgO precipitates in the form of lamellae and rods with median equivalent diameter ranging from 0.19 to 0.85 μm, depending on the pulling rate. The preferred crystallization direction was <111> for both phases, however notable traces of other directions, e.g. <100>, <110> and <331> were found as well.     

Highest UV–vis transparency of MgAl2O4 spinel ceramics prepared by hot pressing with LiF

Reaction sintering of MgO and Al₂O₃ with addition of LiF as sintering additive was used to prepare MgAl₂O₄ spinel ceramic by hot pressing. The process parameter (temperature, pressure, dwell time), the stoichiometric ratio of MgO to Al₂O₃ and the selection of the alumina raw powder are equally important for highest transparency of the spinel ceramic. With this optimization highest transparency of 86% in the visible range at λ = 640 nm together with UV transmission of 62% at 200 nm for spinel ceramic with 4 mm thickness was reached.     

Formation of hollow MgO-rich spinel whiskers in low carbon MgO–C refractories with Al additives

MgO–C refractories with different carbon contents have been developed to meet the requirement of steel-making technologies. Actually, the carbon content in the refractories will affect their microstructure. In the present work, the phase compositions and microstructure of low carbon MgO–C refractories (1 wt% graphite) were investigated in comparison with those of 10 wt% and 20 wt% graphite, respectively. The results showed that Al₄C₃ whiskers and MgAl₂O₄ particles formed for all the specimens fired at 1000 °C. With the temperature up to 1400 °C, more MgAl₂O₄ particles were detected in the matrix and AlN whiskers occurred locally for high carbon MgO–C specimens (10 wt% and 20 wt% graphite). However, the hollow MgO-rich spinel whiskers began to form locally at 1200 °C and grew dramatically at 1400 °C in low carbon MgO–C refractories, whose growth mechanism was dominated by the capillary transportation from liquid Al at these temperatures.     

Experimental phase relations between MgO-saturated magnesium-aluminate spinel (MgAl2O4) and CuOx-rich liquid

Experimental phase equilibrium data for the Cu-O-Al₂O₃-MgO system is required to improve the performance of MgAl₂O₄-containing refractories and slagging in non-ferrous smelting. In this work, the phase relations of MgAl₂O₄ in the Cu-O-Al₂O₃-MgO system were studied experimentally in air within a temperature range of 1100–1400 °C using the equilibration and quenching method. The chemical compositions of the phases in the quenched samples were determined using electron probe microanalysis (EPMA). Less than 1 wt% of Al₂O₃ or MgO were found in the oxide liquid phase, whereas the solid MgAl₂O₄ and MgO phases contained up to 23 wt% and 30 wt% of ‘Cu₂O’, respectively. Discrepancies between these results and the corresponding calculated values generated by the MTDATA 6.0 software and Mtox database Version 8.2 ranged from 3 wt% to 19 wt%. The results of this work indicate that the MgAl₂O₄ spinel is chemically stable in the presence of a CuO_x-rich liquid under the conditions studied.     

Effects of LiF on the microstructure and optical properties of hot-pressed MgAl2O4 ceramics

Transparent magnesium aluminate spinel (MgAl₂O₄) ceramics were fabricated by hot-pressing of the MgO and α-Al₂O₃ powder mixture using LiF as a sintering aid. Effects of the LiF additive on densification, microstructure and optical properties of MgAl₂O₄ ceramics were systematically investigated. It has been found that the addition of LiF can effectively remove the porosity and increase the optical transparency of MgAl₂O₄ ceramics. For the spinel ceramics HP-ed at 1550 °C for 3 h with 1 wt% LiF addition, the average grain size is about 36 µm and the in-line transmittance exceeds 60% at the wavelength of 800 nm.     

Effect of MgAl2O4 nanoparticles addition on the densification and properties of MgO-CaO refractories

MgAl₂O₄nanoparticles were added to MgO–CaO refractory ceramic composites in the range of 0–8 wt%. Refractory specimens were obtained by sintering at 1650 °C for 3 h in an electric furnace. Refractory specimens were characterized by measurements of bulk density, apparent porosity, hydration resistance, cold crushing strength, crystalline phase formation, and microstructural analysis. Results show that with additions of MgAl₂O₄ nanoparticles the bulk density of the samples increased. But the apparent porosity and cold crushing strength decreased and increased, respectively with addition MgAl₂O₄ nanoparticles up to 6 wt% and for further MgAl₂O₄ nanoparticles, due to the thermal expansion mismatch, the results is reversed. Also, the hydration resistance of the samples was appreciably improved by the addition of MgAl₂O₄ nanoparticles due to its effect on decreasing the amount of free CaO in the refractory composite and promotion of densification by creating a dense microstructure.     

Effect of heat treatment conditions on the growth of MgAl2O4 nanoparticles obtained by sol-gel method

MgAl₂O₄ nanoparticles (NPs) were prepared by sol–gel method using aluminium nitrate, magnesium nitrate and citric acid as starting materials, phenolic formaldehyde resin and carbon black as additives. Growth of MgAl₂O₄ NPs in different heat treatment conditions (temperature, atmosphere, carbon additives and in Al₂O₃-C system) was investigated. MgAl₂O₄ NPs were formed at 600 °C in air atmosphere with serious agglomeration of nanoparticles having diameter of approximate 30 nm. The size of MgAl₂O₄ NPs increased greatly from 40 to 50 nm to several hundreds of nanometres as the temperature was raised from 800 °C to 1400 °C. Partial sintering of NPs was observed upon heating at temperatures higher than 1200 °C in air. In reducing atmosphere, the size of MgAl₂O₄ NPs (about 30–50 nm) changed slightly with increasing temperature. This was attributed to the dispersion of carbon inclusions in the MgAl₂O₄ grain boundaries, inducing a steric hindrance effect and inhibiting the growth of particles. MgAl₂O₄ NPs (30–50 nm) in the Al₂O₃-C system were in-situ formed at high temperatures with the use of dried precursor gels. MgAl₂O₄ NPs can contribute to improving the thermal shock resistance of Al₂O₃-C materials.     

Growth and luminescent properties of Ce-doped LiF/LiLuF4 eutectic fibers grown by micro-pulling-down method

The undoped and Ce-doped LiF/LiLuF₄ eutectic fibers with various ratios of LuF₃ to LiF were grown by the micro-pulling-down method for their application as neutron scintillators with light guiding structure. The differential thermal analysis (DTA) of undoped eutectic materials indicated that the eutectic point of LiF/LiLuF₄ was positioned around LiF 80 mol%–LuF₃ 20 mol% composition. Some of the as-produced eutectic solids had rod-like regular array structures. This was observed using SEM images of cross-sectional and parallel cuts of the grown solids. In the range of x ≥ 0.28, the dendrites appeared between the eutectic areas. Ce doped LiF/LiLuF₄ eutectic fibers demonstrated two emission peaks around 310 and 326 nm in the photoluminescence spectrum, and the decay time of the emission at 326 nm was 32.3 ns.     

Dielectric properties of new glass-ceramics for LTCC applied to microwave or millimeter-wave frequencies

A new glass-ceramics material called new-glass-ceramics (NGC) that consists of MgAl₂O₄ crystals (spinel) and highly crystallized Li–Mg–Zn–B–Si–O glass has been developed for microwave or millimeter-wave frequency applications. NGC can be sintered at temperatures below 1000 °C and co-fired with internal copper electrodes that have high electrical conductivity. Its dielectric constant is 7.4 and its Q value is higher than 2000 at 24 GHz. NGC specimens were investigated using X-ray diffraction analysis (XRD), scanning electron microscopy (SEM), and energy dispersive X-ray spectrometry (EDX). NGC mainly consists of MgAl₂O₄, Mg₃B₂O₆, and Li₂MgSiO₄ crystal phases, which have high Q values. Using NGC, we could make band pass filter (BPF) with the size 3.2 mm × 2.5 mm × 1.3 mm for fixed wireless access (F.W.A.) system at 26 GHz. This BPF can be mounted on circuit board by solder and shows good characteristics.     

Microstructures and mechanical properties of directionally solidified Al2O3/GdAlO3 eutectic ceramic by laser floating zone melting with high temperature gradient

Directionally solidified Al₂O₃/GdAlO₃ eutectic ceramic rods with high densities and low solidification defects are prepared by laser floating zone melting at solidification rate from 2 to 200 μm/s. The microstructure evolution, eutectic growth behavior and mechanical properties are investigated. At low solidification rates (<30 μm/s), the eutectic rods present a homogeneous irregular eutectic microstructure, whereas cellular microstructure containing regular lamella/rod structure is developed at higher solidification rates. The relationship is established between the eutectic interphase spacing and solidification rate, which follows the Magnin-Kurz eutectic model. The Vickers hardness (15.9–17.3 GPa) increases slightly with decreasing interphase spacing, but the fracture toughness (4.08 MPa m^1/2) shows little dependence with the solidification rate. Different crack propagation mechanisms are revealed among the indentation cracks. The flexural strength at ambient temperature reaches up to 1.14 GPa for the eutectic grown at 100 μm/s. The fracture surface analysis indicates that the surface defects are the main crack source.     

Poly(N-isopropylacrylamide) assisted microwave synthesis of magnesium aluminate spinel oxide for production of highly transparent films by hot compression

Magnesium aluminate spinel oxides have been prepared via poly(N-isopropylacrylamide) assisted microwave technique. The prepared MgAl₂O₄ powders showed a crystalline cubic structure with spinel phase after calcination at 600 °C only. The poly(N-isopropylacrylamide) amount showed a high effect on the crystallite size and the densification behavior of MgAl₂O₄. The increase of the amount of poly(N-isopropylacrylamide) reduced the sintering temperature of MgAl₂O₄ from 1400 °C to 1050 °C. The hot-pressed of MgAl₂O₄ powders in the presence of 3 wt% of poly(N-isopropylacrylamide) exhibited a full density at sintering temperature 1100 °C in 15 min only. The sintered films showed high transparency (81 ± 2%) in the wavelength range 500–1000 nm.     

Low cost foam-gelcasting preparation and characterization of porous magnesium aluminate spinel (MgAl2O4) ceramics

Porous MgAl₂O₄ ceramics were prepared via a low cost foam-gelcasting route using MgAl₂O₄ powders as the main raw material, ammonium polyacrylate as a dispersant, a small amount of modified carboxymethyl cellulose as a gelling agent, and TH-IV polymer as a foaming agent. The effects of additive's content, solid loading and gelling temperature on slurry's rheological behavior were investigated, and microstructures and properties of as-prepared porous MgAl₂O₄ ceramics examined. Based on the results, the roles played by the foaming agent in the cases of porosity, pore structure, pore size, mechanical properties and thermal conductivity were clarified. Porosity and pore sizes of as-prepared porous MgAl₂O₄ ceramics increased with increasing the foaming agent from 0.05 to 0.6 vol%. Porous MgAl₂O₄ ceramics with porosity of 75.1% and average pore size of 266 µm exhibited a compressive strength as high as 12.5±0.8 MPa and thermal conductivity as low as 0.24 W/(m K) (at 473 K).     

Capillary rise properties of porous mullite ceramics prepared by an extrusion method using organic fibers as the pore former

Porous mullite ceramics with unidirectionally oriented pores were prepared by an extrusion method to investigate their capillary rise properties. Rayon fibers 16.5 μm in diameter and 800 μm long were used as the pore formers by kneading with alumina powder, kaolin clay, China earthen clay and binder with varying Fe₂O₃ contents of 0, 5 and 7 mass%. The resulting pastes were extruded into cylindrical tubes (outer diameter (OD) 30–50 mm and inner diameter (ID) 20–30 mm), dried at room temperature and fired at 1500 °C for 4 h. The bulk densities of the resulting porous ceramics ranged from 1.31 to 1.67 g/cm³, with apparent porosities of 43.2–59.3%. The pore size distributions measured by Hg porosimetry showed a sharp peak at 10.0 μm in the sample without Fe₂O₃ and at 15.6 μm in the samples containing Fe₂O₃; these pores, which arose from the burnt-out rayon fibers, corresponded to total pore volumes ranging from 0.24 to 0.34 ml/g. SEM showed a microstructure consisting of unidirectionally oriented pores in a porous mullite matrix. Prismatic mullite crystals were well developed on the surfaces of the pore walls owing to the liquid phase formed by the Fe₂O₃ component added to color the samples. The bending strengths of the tubular samples ranged from 15.6 to 26.3 MPa. The height of capillary rise, measured under controlled relative humidities (RH) of 50, 65 and 85%, was greater in the ceramics containing Fe₂O₃ than in those without Fe₂O₃, especially in the thinner samples. The maximum capillary rise reached about 1300 mm, much higher than previously reported. This excellent capillary rise ability is thought to be due to the controlled pore size, pore distribution and pore orientation in these porous mullite ceramics.     

Crystal growth of LiF/LiYF4 eutectic crystals and their luminescent properties

Undoped and 0.5 mol% Ce-doped LiF–LiYF₄ eutectic crystals were grown by the micro-pulling-down method at different growth rates. The SEM images of all the eutectic crystals showed LiF with rod-like structure in the LiYF₄ matrix. The diameter of the rod phase systematically decreased with the increase of the growth rate. The radioluminescence spectra of cerium doped crystal under alpha-ray excitation showed emission peak at 325 nm related to Ce³⁺ 5d-4f transition. The white part in the cathodoluminescence image is considered to be due to Ce³⁺ ion in LiYF₄ phase, according to the scanning electron microscopy (SEM) image in the same region.