A Hybrid Spur Compensation Technique for Finite-Modulo Fractional-N Phase-Locked Loops

A finite-modulo fractional-$N$ PLL utilizing a low-bit high-order $DeltaSigma$ modulator is presented. A 4-bit fourth-order $DeltaSigma$ modulator not only performs non-dithered 16-modulo fractional-$N$ operation but also offers less spur generation with negligible quantization noise. Further spur reduction is achieved by charge compensation in the voltage domain and phase interpolation in the time domain, which significantly relaxes the dynamic range requirement of the charge pump compensation current. A 1.8–2.6 GHz fractional-$N$ PLL is implemented in 0.18 $mu{hbox {m}}$ CMOS. By employing high-order deterministic $DeltaSigma$ modulation and hybrid spur compensation, the spur level of less than $-$55 dBc is achieved when the ratio of the bandwidth to minimum frequency resolution is set to 1/4. The prototype PLL consumes 35.3 mW in which only 2.7 mW is consumed by the digital modulator and compensation circuits.      

A 0.13 $mu$ m CMOS Quad-Band GSM/GPRS/EDGE RF Transceiver Using a Low-Noise Fractional-N Frequency Synthesizer and Direct-Conversion Architecture

This paper presents a single-chip CMOS quad-band (850/900/1800/1900 MHz) RF transceiver for GSM/GPRS/EDGE applications which adopts a direct-conversion receiver, a direct-conversion transmitter and a fractional-N frequency synthesizer with a built-in DCXO. In the GSM mode, the transmitter delivers 4 dBm of output power with 1$^{circ}$ RMS phase error and the measured phase noise is ${-}$164.5 dBc/Hz at 20 MHz offset from a 914.8$~$MHz carrier. In the EDGE mode, the TX RMS EVM is 2.4% with a 0.5 $~$dB gain step for the overall 36 dB dynamic range. The RX NF and IIP3 are 2.7 dB/ ${-}$12 dBm for the low bands (850/900 MHz) and 3 dB/${-}$ 11 dBm for the high bands (1800/1900 MHz). This transceiver is implemented in 0.13 $mu$m CMOS technology and occupies 10.5 mm$^{2}$ . The device consumes 118 mA and 84 mA in TX and RX modes from 2.8 V, respectively and is housed in a 5$,times,$ 5 mm$^{2}$ 40-pin QFN package.      

An FIR-Embedded Noise Filtering Method for $Delta Sigma$ Fractional-N PLL Clock Generators

This paper describes a noise filtering method for $Delta Sigma$ fractional- $N$ PLL clock generators to reduce out-of-band phase noise and improve short-term jitter performance. Use of a low-cost ring VCO mandates a wideband PLL design and complicates filtering out high-frequency quantization noise from the $Delta Sigma$ modulator. A hybrid finite impulse response (FIR) filtering technique based on a semidigital approach enables low-OSR $Delta Sigma$ modulation with robust quantization noise reduction despite circuit mismatch and nonlinearity. A prototype 1-GHz $Delta Sigma$ fractional-$N$ PLL is implemented in 0.18 $muhbox{m}$ CMOS. Experimental results show that the proposed semidigital method effectively suppresses the out-of-band quantization noise, resulting in nearly 30% reduction in short-term jitter.      

Characterization and Modeling of RF-Performance $(f_{T})$ Fluctuation in MOSFETs

The fluctuation of RF performance (particularly for $f_{T}$ : cutoff frequency) in the transistors fabricated by 90-nm CMOS technology has been investigated. The modeling for $f_{T}$ fluctuation is well fitted with the measurement data within approximately 1% error. Low-$V_{t}$ transistors (fabricated by lower doping concentration in the channel) show higher $f_{T}$ fluctuation than normal transistors. Such a higher $f_{T}$ fluctuation results from $C_{rm gg}$ (total gate capacitance) variation rather than $g_{m}$ variation. More detailed analysis shows that $C_{rm gs} + C_{rm gb}$ (charges in the channel and the bulk) are predominant factors over $C_{rm gd}$ (charges in LDD/halo region) to determine $C_{rm gg}$ fluctuation.      

A 25-MHz Self-Referenced Solid-State Frequency Source Suitable for XO-Replacement

Recent trends in the development of integrated silicon frequency sources are discussed. Within that context, a 25-MHz self-referenced solid-state frequency source is presented and demonstrated where measured performance makes it suitable for replacement of crystal oscillators (XOs) in data interface applications. The frequency source is referenced to a frequency-trimmed and temperature-compensated 800-MHz free-running $LC$ oscillator (LCO) that is implemented in a standard logic CMOS process and with no specialized analog process options. Mechanisms giving rise to frequency drift in integrated LCOs are discussed and supported by analytical expressions. Design objectives and a compensation technique are presented where several implementation challenges are uncovered. Fabricated in a 0.25-$mu$m 1P5M CMOS process, and with no external components, the prototype frequency source dissipates 59.4 mW while maintaining ${pm} 152$ ppm frequency inaccuracy over process, ${pm} 10hbox{%}$ variation in the power supply voltage, and from ${-}$ 10 $^{circ}$ C to 80 $^{circ}$ C. Variation against other environmental factors is also presented. Nominal period jitter and power-on start-up latency are 2.75 ps$_{rm rms}$ and 268 $mu$s, respectively. These performance metrics are compared with an XO at the same frequency.      

$S$ - and $C$ -Band Ultra-Compact Phase Shifters Based on All-Pass Networks

Ultra-compact phase shifters are presented. The proposed phase-shifting circuits utilize the lumped element all-pass networks. The transition frequency of the all-pass network, which determines the size of the circuit, is set to be much higher than the operating frequency. This results in a significantly small chip size of the phase shifter. To verify this methodology, 5-bit phase shifters have been fabricated in the $S$ - and $C$ -band. The $S$ -band phase shifter, with a chip size of 1.87 mm $,times,$0.87 mm (1.63 mm $^{2}$), has achieved an insertion loss of ${hbox{6.1 dB}} pm {hbox{0.6 dB}}$ and rms phase-shift error of less than 2.8$^{circ}$ in 10% bandwidth. The $C$ -band phase shifter, with a chip size of 1.72 mm $,times,$0.81 mm (1.37 mm $^{2}$), has demonstrated an insertion loss of 5.7 dB $pm$ 0.8 dB and rms phase-shift error of less than 2.3 $^{circ}$ in 10% bandwidth.      

Compact $S$ -/$Ka$-Band CMOS Quadrature Hybrids With High Phase Balance Based on Multilayer Transformer Over-Coupling Technique

This paper presents compact CMOS quadrature hybrids by using the transformer over-coupling technique to eliminate significant phase error in the presence of low-$Q$ CMOS components. The technique includes the inductive and capacitive couplings, where the former is realized by employing a tightly inductive-coupled transformer and the latter by an additional capacitor across the transformer winding. Their phase balance effects are investigated and the design methodology is presented. The measurement results show that the designed 24-GHz CMOS quadrature hybrid has excellent phase balance within ${pm}{hbox{0.6}}^{circ}$ and amplitude balance less than ${pm} {hbox{0.3}}$ dB over a 16% fractional bandwidth with extremely compact size of 0.05 mm$^{2}$. For the 2.4-GHz hybrid monolithic microwave integrated circuit, it has measured phase balance of ${pm}{hbox{0.8}}^{circ}$ and amplitude balance of ${pm} {hbox{0.3}}$ dB over a 10% fractional bandwidth with a chip area of 0.1 mm$^{2}$ .      

Integrated Quadrature Couplers and Their Application in Image-Reject Receivers

Several fully-integrated multi-stage lumped-element quadrature hybrids that enhance bandwidth, amplitude and phase accuracies, and robustness are presented, and a fully-integrated double-quadrature heterodyne receiver front-end that uses two-stage Lange/Lange couplers is described. The Lange/Lange cascade exploits the inherent wide bandwidth characteristic of the Lange hybrid and enables a robust design using a relatively low transformer coupling coefficient. The measured image-rejection ratio is $>$ 55 dB over a 200 MHz bandwidth centered around 5.25 $~$GHz without any tuning, trimming, or calibration; the front-end features 23.5 dB gain, $-$79 dBm sensitivity, 5.6 dB SSB NF, $-$7$~$ dBm IIP3, $-$18 dB $S_{11}$ and a 1 mm $times$ 2 mm die area in 0.18$ mu{hbox {m}}$ CMOS.      

A V-Band CMOS VCO With an Admittance-Transforming Cross-Coupled Pair

A novel circuit topology suitable for the implementation of CMOS voltage-controlled oscillators (VCOs) at millimeter-wave frequencies is presented in this paper. By employing transmission line segments to transform the admittance of the additional cross-coupled pair, the proposed LC-tank VCO can sustain fundamental oscillation at a frequency close to the $f _{max}$ of the transistors. Using a standard 0.18 $muhbox{m}$ CMOS process, a V-band VCO is realized for demonstration. The fabricated circuit exhibits a frequency tuning range of 670 MHz in the vicinity of 63 GHz. The measured output power and phase noise at 1 MHz offset are $-hbox{15~dBm}$ and $-hbox{89~dBc}/hbox{Hz}$ , respectively. Operated at a 1.8 $~$V supply voltage, the VCO core and the output buffer consume a total DC current of 55 mA.      

Schottky Barrier Height Modulation of Nickel–Dysprosium-Alloy Germanosilicide Contacts for Strained P-FinFETs

This letter reports on the fabrication and hole Schottky barrier $(Phi_{ rm B}^{rm p})$ modulation of a novel nickel (Ni)–dysprosium (Dy)-alloy germanosilicide (NiDySiGe) on silicon–germanium (SiGe). Aluminum (Al) implant is utilized to lower the $Phi_{rm B}^{rm p}$ of NiDySiGe from $sim$0.5 to $sim$ 0.12 eV, with a correspondingly increasing Al dose in the range of $ hbox{0}$–$hbox{2}timeshbox{10}^{15} hbox{atoms}/ hbox{cm}^{2}$. When integrated as the contact silicide in p-FinFETs (with SiGe source/drain), NiDySiGe with an Al implant dose of $hbox{2}timeshbox{10}^{14} hbox{atoms}/ hbox{cm}^{2}$ leads to 32% enhancement in $I_{rm DSAT}$ over p-FinFETs with conventional NiSiGe contacts. Ni–Dy-alloy silicide is a promising single silicide solution for series-resistance reduction in CMOS FinFETs.      

A Low Phase-Noise QVCO With Integrated Back-Gate Coupling and Source Resistive Degeneration Technique

A 0.18 $mu$ m CMOS quadrature voltage-controlled oscillator with an extremely-low phase noise is presented. The excellent phase noise performance is accomplished by integration of the back-gate quadrature phase coupling and source resistive degeneration techniques into a complementary oscillator topology. The measured phase noise is as low as ${-}133$ dBc/Hz at 1 MHz offset from 3.01 GHz. The output phase imbalance is less than 1$^{circ}$ . The output power is $-1.25{pm} 0.5$ dBm and harmonic suppression is greater than 30.8 dBc. The oscillator core consumes 5.38 mA from a 1.5 V power supply. This QVCO achieves the highest figure-of-merit of ${-}193.5$ dBc/Hz.      

180$^{circ}$ and 90$^{circ}$ Phase Shifting Networks With an Octave Bandwidth and Small Phase Errors

A new phase shifting network for both 180 $^{circ}$ and 90 $^{circ}$ phase shift with small phase errors over an octave bandwidth is presented. The theoretical bandwidth is 67% for the 180$^{circ}$ phase bit and 86% for the 90$^{circ}$ phase bit when phase errors are $pm 2^{circ}$. The proposed topology consists of a bandpass filter (BPF) branch, consisting of a LC resonator and two shunt quarter-wavelength transmission lines (TLs), and a reference TL. A theoretical analysis is provided and scalable parameters are listed for both phase bits. To test the theory, phase shifting networks from 1 GHz to 3 GHz were designed. The measured phase errors of the 180$^{circ}$ and the 90$^{circ}$ phase bit are $pm 3.5^{circ}$ and $pm 2.5^{circ}$ over a bandwidth of 73% and 102% while the return losses are better than 18 dB and 12 dB, respectively.      

A Low-Voltage Mobility-Based Frequency Reference for Crystal-Less ULP Radios

The design of a 100 kHz frequency reference based on the electron mobility in a MOS transistor is presented. The proposed low-voltage low-power circuit requires no off-chip components, making it suitable for application in wireless sensor networks (WSN). After a single-point calibration, the spread of its output frequency is less than 1.1% (3$sigma $) over the temperature range from $-{hbox{22}},^{circ}{hbox{C}}$ to 85$,^{circ}{hbox{C}}$ . Fabricated in a baseline 65$~$nm CMOS technology, the frequency reference circuit occupies 0.11$ hbox{mm}^{2}$ and draws 34 $ muhbox{A}$ from a 1.2 V supply at room temperature.      

A 0.8 V, 2.6 mW, 88 dB Dual-Channel Audio Delta-Sigma D/A Converter With Headphone Driver

A 0.8 V third-order multibit $DeltaSigma$ DAC with headphone driver is described. It is the first sub-1 V audio $DeltaSigma$ DAC with integrated on-chip headphone driver. The dual-channel operation in digital section was efficiently realized with a time-interleaved single-channel hardware and extra registers. Using novel DAC architecture suitable for low-voltage operation, the analog section requires only one opamp per channel for the D/A conversion, low-pass filtering, and driving the headphone. Two prototype ICs (separate digital and analog chips), implemented in a 0.35$ muhbox{m}$ CMOS process, achieved an 88 dB dynamic range, while consuming 2.6 mW from a 0.8 V supply.      

A Phase-Locked Loop With Injection-Locked Frequency Multiplier in 0.18-$mu{hbox{m}}$ CMOS for $V$ -Band Applications

In this paper, a novel CMOS phase-locked loop (PLL) integrated with an injection-locked frequency multiplier (ILFM) that generates the $V$-band output signal is proposed. Since the proposed ILFM can generate the fifth-order harmonic frequency of the voltage-controlled oscillator (VCO) output, the operational frequency of the VCO can be reduced to only one-fifth of the desired frequency. With the loop gain smaller than unity in the ILFM, the output frequency range of the proposed PLL is from 53.04 to 58.0 GHz. The PLL is designed and fabricated in 0.18-$mu{hbox{m}}$ CMOS technology. The measured phase noises at 1- and 10-MHz offset from the carrier are $-$ 85.2 and $-{hbox{90.9 dBc}}/{hbox{Hz}}$, respectively. The reference spur level of $-{hbox{40.16 dBc}}$ is measured. The dc power dissipation of the fabricated PLL is 35.7 mW under a 1.8-V supply. It can be seen that the advantages of lower power dissipation and similar phase noise can be achieved in the proposed PLL structure. It is suitable for low-power and high-performance $V$-band applications.      

$hbox{TiN/ZrO}_{2}$/Ti/Al Metal–Insulator–Metal Capacitors With Subnanometer CET Using ALD-Deposited $hbox{ZrO}_{2}$ for DRAM Applications

We provide the first report of the structural and electrical properties of $hbox{TiN/ZrO}_{2}$/Ti/Al metal–insulator–metal capacitor structures, where the $hbox{ZrO}_{2}$ thin film (7–8 nm) is deposited by ALD using the new zirconium precursor ZrD-04, also known as Bis(methylcyclopentadienyl) methoxymethyl. Measured capacitance–voltage ($C$– $V$) and current–voltage ( $I$–$V$) characteristics are reported for premetallization rapid thermal annealing (RTP) in $hbox{N}_{2}$ for 60 s at 400 $^{circ}hbox{C}$, 500 $^{circ}hbox{C}$, or 600 $^{ circ}hbox{C}$. For the RTP at 400 $^{circ}hbox{C}$ , we find very low leakage current densities on the order of nanoamperes per square centimeter at a gate voltage of 1 V and low capacitance equivalent thickness values of $sim$ 0.9 nm at a gate voltage of 0 V. The dielectric constant of $ hbox{ZrO}_{2}$ is 31 $pm$ 2 after RTP treatment at 400 $^{circ}hbox{C}$.      

Oversampling A/D Converters With Reduced Sensitivity to DAC Nonlinearities

To alleviate the image-rejection requirements of the front-end filters and the feedback digital-to-analog converter (DAC) matching requirements, an oversampling complex discrete-time (DT) $DeltaSigma$ analog-to-digital converter (ADC) with a signal-transfer function that achieves significant filtering of interfering signals is proposed. With a filtering signal transfer function (STF) and stopband attenuation greater than 30 dB, the $DeltaSigma$ modulator reduces the intermodulation of the desired signal and the interfering signals at the input of a quantizer, and also avoids feedback of high-frequency interfering signals at the input of the modulator. This filtering of the interfering signals reduces sensitivity to DAC nonlinearities. The reported DT complex $DeltaSigma$ ADC is intended for digital television (DTV) receiver applications. With a maximum intended sampling frequency of 128 MHz and an oversampling ratio of 16, the ADC has been designed to support a maximum DTV signal bandwidth of 8 MHz. The IC achieved a 70.9-dB signal-to-noise-and-distortion ratio over a 6-MHz band centered around 3 MHz. The image-rejection ratio of the $DeltaSigma$ ADC was measured to be greater than 65 dB. The fabricated chip consumes 122.4 mW and occupies a silicon area of 2.15 $hbox{mm}^{2}$.      

A 14 mW Fractional-N PLL Modulator With a Digital Phase Detector and Frequency Switching Scheme

In this work an all-digital phase detector for a fractional-${N}$ PLL is proposed and demonstrated. The phase detector consists of a single flip-flop, which acts as an oversampled 1 bit phase quantizer. A digital sampling scheme that enables FSK modulation rates much larger than the loop bandwidth is demonstrated, without compromising on the frequency accuracy of the output signal. A prototype 2.2 GHz fractional-${N}$ synthesizer incorporating the digital phase detector and sampling scheme is presented as a proof of concept. Although the loop bandwidth is only 142 kHz, an FSK modulation rate of 927.5 kbs is achieved. The 0.7 ${hbox{mm}}^{2}$ prototype is implemented in 0.13 $mu{hbox{m}}$ CMOS consumes 14 mW from a 1.4 V supply.      

A Fully Differential Comparator-Based Switched-Capacitor $DeltaSigma$ Modulator

In this brief, a fully differential comparator-based switched-capacitor (CBSC) second-order delta-sigma $(DeltaSigma)$ modulator is presented. To ensure differential operation, the CBSC $DeltaSigma$ modulator utilizes a common-mode feedback circuit to balance the pull-up current and the pull-down current in the ramp generator. This modulator has been fabricated in a standard 0.18-$muhbox{m}$ CMOS process. The active area is 0.21 $hbox{mm}^{2}$, and the power consumption, excluding output buffers, is 0.42 mW from a 1.8-V supply. This modulator achieves 65.3-dB signal-to-noise-plus-distortion ratio and an input dynamic range of 71 dB when sampled at 2.56 MS/s $(hbox{OSR} = 64)$.      

A Relationship Between Phase Delay and Attenuation Due to Rain and Its Applications to Satellite and Deep-Space Tracking

We present and discuss two main results concerning the relationship between phase delay due to rain and rain attenuation, useful in calculations concerning high precision tracking of satellites and deep-space spacecrafts using interferometry techniques. We have found these two results with the Synthetic Storm Technique [SST] applied to a large data bank of rain rate time series collected at three sites in Italy. The first result concerns a formula that provides the extra signal phase delay $tau$ (picoseconds) due to rain as a function of rain attenuation $A$ (dB), frequency $f$ (GHz) and slant path elevation angle $theta$ (degrees), given by $tau = (860.4 - 4.82 theta)f^{- 1.71}A^{0.73}$, for $20^{circ} leq theta ≪ 44^{circ}$, and by $tau = 648.3f^{- 1.71}A^{0.73}$, for $44^{circ} leq theta leq 90^{circ}$ . The formula allows estimating the phase delay due to rain attenuation, with overall average (normalized) error ${-}3hbox{%}$, standard deviation 11.1%, root-mean square 11.5% for 20$^{circ}$ slant paths. The second result concerns a method to predict phase delay from the probability distribution of rain rate (SST probability model), very useful when only the probability distribution of rain rate is known.