Synthesis, phase relation and electrical and electrochemical properties of ruthenium-substituted Li2MnO3 as a novel cathode material

Layered oxides, ruthenium-substituted Li₂MnO₃, were synthesized at 800 °C and 1200 °C. Their phase relation and electrical and electrochemical properties were investigated. Li₂Mn_1−xRu_xO₃ synthesized at 800 °C clearly separated into two phases, manganese-rich and ruthenium-rich phases, except for the narrow composition range of 0 ≤ x ≤ 0.05, while Li₂Mn_1−xRu_xO₃ synthesized at 1200 °C formed two solid solutions in the whole composition range across a structural transition between x = 0.6 and 0.8. The electrical resistivity of Li₂Mn_1−xRu_xO₃ decreased with increasing ruthenium content. Li₂Mn_0.2Ru_0.8O₃ (x = 0.8) synthesized at 1200 °C showed the lowest resistivity of 5.7 × 10² Ω cm at room temperature. The discharge capacity and cycling performance were improved by the ruthenium substitution. Li₂Mn_0.4Ru_0.6O₃ (x = 0.6) exhibited a discharge capacity of 192 mAh g⁻¹ in the initial cycle and 169 mAh g⁻¹ in the tenth cycle with high and almost constant charge-discharge efficiencies of 99% from the second to tenth cycle at a current rate of 1/10C. The ruthenium substitution to Li₂MnO₃ is quite effective to improve electrical conductivity and charge-discharge performance.     

Fabrication and electrochemical characterization of a vertical array of MnO2 nanowires grown on silicon substrates as a cathode material for lithium rechargeable batteries

A complementary metal-oxide-semiconductor (CMOS) compatible process for fabricating on-chip microbatteries based on nanostructures has been developed by growing manganese dioxide nanowires on silicon dioxide (SiO₂)/silicon (Si) substrate as a cathode material for lithium rechargeable batteries. High aspect-ratio anodized aluminum oxide (AAO) template integrated on SiO₂/Si substrates can be exploited for fabrication of a vertical array of nanowires having high surface area. The electrolytic manganese dioxide (EMD) nanowires are galvanostatically synthesized by direct current (dc) electrodeposition. The microstructure of these nanowire arrays is investigated by scanning electron microscopy and X-ray diffraction. Their electrochemical tests show that the discharge capacity of about 150 mAh g⁻¹ is maintained during a few cycles at the high discharge/charge rate of 300 mA g⁻¹.     

Synthesis and performance of Li3(V1−xMgx)2(PO4)3 cathode materials

In order to search for cathode materials with better performance, Li₃(V_1−xMg_x)₂(PO₄)₃ (0, 0.04, 0.07, 0.10 and 0.13) is prepared via a carbothermal reduction (CTR) process with LiOH·H₂O, V₂O₅, Mg(CH₃COO)₂·4H₂O, NH₄H₂PO₄, and sucrose as raw materials and investigated by X-ray diffraction (XRD), scanning electron microscopic (SEM) and electrochemical impedance spectrum (EIS). XRD shows that Li₃(V_1−xMg_x)₂(PO₄)₃ (x = 0.04, 0.07, 0.10 and 0.13) has the same monoclinic structure as undoped Li₃V₂(PO₄)₃ while the particle size of Li₃(V_1−xMg_x)₂(PO₄)₃ is smaller than that of Li₃V₂(PO₄)₃ according to SEM images. EIS reveals that the charge transfer resistance of as-prepared materials is reduced and its reversibility is enhanced proved by the cyclic votammograms. The Mg²⁺-doped Li₃V₂(PO₄)₃ has a better high rate discharge performance. At a discharge rate of 20 C, the discharge capacity of Li₃(V_0.9Mg_0.1)₂(PO₄)₃ is 107 mAh g⁻¹ and the capacity retention is 98% after 80 cycles. Li₃(V_0.9Mg_0.1)₂(PO₄)₃//graphite full cells (085580-type) have good discharge performance and the modified cathode material has very good compatibility with graphite.     

Synthesis and characterization of Li2MnSiO4/C nanocomposite cathode material for lithium ion batteries

A high capacity Li₂MnSiO₄/C nanocomposite cathode material with good rate performance for lithium ion batteries through a solution route has been successfully prepared. The material is able to deliver a reversible capacity of 209 mAh g⁻¹ in the first cycle, i.e. more than one electron exchange can be reversible cycled in the materials. The highly dispersion of nanocrystalline Li₂MnSiO₄ which was surround by a thin film of carbon was attributed to the cause of excellent performance of the materials. Ex situ XRD and IR results show that poor cycling behavior of Li₂MnSiO₄ might be due to an amorphization process of the materials.     

Synthesis and electrochemical performance of Li2CoSiO4 as cathode material for lithium ion batteries

Li₂CoSiO₄ has been prepared successfully by a solution route or hydrothermal reaction for the first time, and its electrochemical performance has been investigated primarily. Reversible extraction and insertion of lithium from and into Li₂CoSiO₄ at 4.1 V versus lithium have shown that this material is a potential candidate for the cathode in lithium ion batteries. At this stage reversible electrochemical extraction was limited to 0.46 lithium per formula unit for the Li₂CoSiO₄/C composite materials, with a charge capacity of 234 mAh g⁻¹ and a discharge capacity of 75 mAh g⁻¹.     

Preparation of α-LiFeO2-based cathode materials by an ionic exchange method

β-FeOOH prepared with an enhanced hydrolysis method had been subjected to H⁺/Li⁺ exchange with various lithium salts in ethanol for various duration. The effects of the kind of lithium salt used and the duration of ionic exchange on the composition, the crystalline structure, and the electrochemical properties of the prepared powders were investigated. It was found that α-LiFeO₂ can be prepared from β-FeOOH by an ionic exchange reaction with LiOH in ethanol at 85 °C. α-LiFeO₂ powders so prepared show electrochemical active properties with reversible capacity of 65–80 mAh g⁻¹. The in situ XRD patterns of the cycled α-LiFeO₂ cathode revealed that the crystalline structure remains unchanged while the lattice of cubic decreases and increases periodically upon charge/discharge cycling. The results of XANES suggest that the electrochemical reaction of the Fe³⁺/Fe²⁺ redox couple occurs as the prepared α-LiFeO₂ electrode is charge/discharge cycled.     

A novel sol-gel method based on FePO4·2H2O to synthesize submicrometer structured LiFePO4/C cathode material

Carbon coated LiFePO₄/C cathode material is synthesized with a novel sol-gel method, using cheap FePO₄·2H₂O as both iron and phosphorus sources and oxalic acid (H₂C₂O₄·2H₂O) as both complexant and reductant. In H₂C₂O₄ solution, FePO₄·2H₂O is very simple to form transparent sols without controlling the pH value. Pure submicrometer structured LiFePO₄ crystal is obtained with a particle size ranging from 100 to 500 nm, which is also uniformly coated with a carbon layer, about 2.6 nm in thickness. The as-synthesized LiFePO₄/C sample exhibits high initial discharge capacity 160.5 mAh g⁻¹ at 0.1 C rate, with a capacity retention of 98.7% after 50th cycle. The material also shows good high-rate discharge performances, about 106 mAh g⁻¹ at 10 C rate. The improved electrochemical properties of as-synthesized LiFePO₄/C are ascribed to its submicrometer scale particles and low electrochemical impedance. The sol-gel method may be of great interest in the practical application of LiFePO₄/C cathode material.     

Electrochemical performance of all-solid-state Li batteries based LiMn0.5Ni0.5O2 cathode and NASICON-type electrolyte

LiNi_0.5Mn_0.5O₂ thin films have been deposited on the NASICON-type glass ceramics, Li_1+x+yAl_xTi_2−xSi_yP_3−yO₁₂ (LATSP), by radio frequency (RF) magnetron sputtering followed by annealing. The films have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and Raman spectroscopy. All-solid-state Li/PEO₁₈-Li(CF₃SO₂)₂N/LATSP/LiNi_0.5Mn_0.5O₂/Au cells are fabricated using the LiNi_0.5Mn_0.5O₂ thin films and the LATSP electrolyte. The electrochemical performance of the cells is investigated by galvanostatic cycling, cyclic voltammetry (CV), potentiostatic intermittent titration technique (PITT) and electrochemical impedance spectroscopy (EIS). Interfacial reactions between LiNi_0.5Mn_0.5O₂ and LATSP occur at a temperature as low as 300 °C with the formation of Mn₃O₄, resulting in an increased obstacle for Li-ion diffusion across the LiNi_0.5Mn_0.5O₂/LATSP interface. The electrochemical performance of the cells is limited by the interfacial resistance between LATSP and LiNi_0.5Mn_0.5O₂ as well as the Li-ion diffusion kinetics in LiNi_0.5Mn_0.5O₂ bulk.     

Preparation of spherical LiNi0.80Co0.15Mn0.05O2 lithium-ion cathode material by continuous co-precipitation

Micro-spherical Ni_0.80Co_0.15Mn_0.05(OH)₂ precursors with a narrow size-distribution and high tap-density are prepared successfully by continuous co-precipitation of the corresponding metal salt solutions using NaOH and NH₄OH as precipitation and complexing agents. LiNi_0.80Co_0.15Mn_0.05O₂ is then prepared as a lithium battery cathode from this precursor by the introduction of LiOH·H₂O. The pH and NH₃:metal molar ratio show significant effects on the morphology, microstructure and tap-density of the prepared Ni_0.80Co_0.15Mn_0.05(OH)₂ and the R values and I(0 0 3)/I(1 0 4) ratio of lithiated LiNi_0.80Co_0.15Mn_0.05O₂. Spherical LiNi_0.80Co_0.15Mn_0.05O₂ prepared under optimum conditions reveals a hexagonally ordered, layered structure without cation mixing and an initial charging capacity of 176 mAhg⁻¹. More than 91% of the capacity is retained after 40 cycles at the 1 C rate in a cut-off voltage range of 4.3-3.0 V.     

Preparation and characterization of Ti-doped LiFePO4 cathode materials for lithium-ion batteries

Olivine structured LiFePO₄ (lithium iron phosphate) and Ti⁴⁺-doped LiFe_1−xTi_xPO₄ (0.01 ≤ x ≤ 0.09) powders were synthesized via a solution route followed by heat-treatment at 700 °C for 8 h under N₂ flowing atmosphere. The compositions, crystalline structure, morphology, carbon content, and specific surface area of the prepared powders were investigated with ICP-OES, XRD, TEM, SEM, EA, and BET. Capacity retention study was used to investigate the effects of Ti⁴⁺ partial substitution on the intercalation/de-intercalation of Li⁺ ions in the olivine structured cathode materials. Among the prepared powders, LiFe_0.97Ti_0.03PO₄ manifests the most promising cycling performance as it was cycled with C/10, C/5, C/2, 1C, 2C, and 3C rate. It showed initial discharge capacity of 135 mAh g⁻¹ at 30 °C with C/10 rate. From the results of GSAS refinement for the prepared samples, the doped-Ti⁴⁺ ions did not occupy the Fe²⁺ sites as expected. However, the occupancy of the doped Ti⁴⁺ ions are still not clear, and theoretical calculations are needed for further studies. From the variation of lattice parameters calculated by the least square method without refinement, it suggested that Ti⁴⁺-doped LiFePO₄ samples formed solid solutions at low doping levels while TiO₂ was also observed with TEM in samples prepared with doping level higher than 5 mol%.     

Reaction mechanism and kinetics of lithium ion battery cathode material LiNiO2 with CO2

The reaction between LiNiO₂ and CO₂ is relevant to the synthesis and storage of LiNiO₂-based cathode materials for lithium ion batteries. In this work, this reaction was investigated in pure CO₂ atmosphere at both room and high temperatures. The reaction products (Li₂CO₃, NiO, and O₂) and activation energies were determined by means of XRD, XPS, MS and TGA techniques. The reaction mechanism was explored in an effort to clarify some inconsistencies in the previous works. Kinetics analysis was also carried out to understand the reaction process relevant to the synthesis and storage of LiNiO₂ cathode material.     

Synthesis, structure and electrochemical Li insertion behaviour of Li2Ti6O13 with the Na2Ti6O13 tunnel-structure

Li₂Ti₆O₁₃ has been prepared from Na₂Ti₆O₁₃ by Li ion exchange in molten LiNO₃ at 325 °C. Chemical analysis and powder X-ray diffraction study of the reaction product respectively indicate that total Na/Li exchange takes place and the Ti-O framework of the Na₂Ti₆O₁₃ parent structure is kept under those experimental conditions. Therefore, Li₂Ti₆O₁₃ has been obtained with the mentioned parent structure. An important change is that particle size is decreased significantly which is favoring lithium insertion. Electrochemical study shows that Li₂Ti₆O₁₃ inserts ca. 5 Li per formula unit in the voltage range 1.5-1.0 V vs. Li⁺/Li, yielding a specific discharge capacity of 250 mAh g⁻¹ under equilibrium conditions. Insertion occurs at an average equilibrium voltage of 1.5 V which is observed for oxides and titanates where Ti(IV)/Ti(III) is the active redox couple. However, a capacity loss of ca. 30% is observed due to a phase transformation occurring during the first discharge. After the first redox cycle a high reversible capacity is obtained (ca. 160 mAh g⁻¹ at C/12) and retained upon cycling. Taking into consideration these results, we propose Li₂Ti₆O₁₃ as an interesting material to be further investigated as the anode of lithium ion batteries.     

Enhanced electrochemical properties of Li(Ni0.4Co0.3Mn0.3)O2 cathode by surface modification using Li3PO4-based materials

The surface of a commercial Li[Ni_0.4Co_0.3Mn_0.3]O₂ cathode is modified using Li₃PO₄-based coating materials. The electrochemical properties of the coated materials are investigated as a function of the pH value of the coating solution and the composition of coating materials. The Li₃PO₄ coating solution with pH 2 is found to be favorable for the formation of stable coating layers having enhanced electrochemical properties. The Li₃PO₄, Li_1.5PO₄, and PO₄ coating layers are formed as amorphous phases. However, the Li_3−xNi_x/2PO₄ coating layers are composed of small particles with a crystalline phase covered with an amorphous phase. Li₃PO₄ and Li_1.5PO₄ coatings considerably enhance the rate capability of the Li[Ni_0.4Co_0.3Mn_0.3]O₂ electrode. In contrast, the Li_3−xNi_x/2PO₄ coating material, which contained Ni, has an inferior rate capability compared to the Li_xPO₄ series (x = 1.5 and 3), although the LiNiPO₄-coated electrode shows a better rate capability than a pristine one. Li₃PO₄-based coating materials are effective at enhancing the cyclic performance of the electrode in the voltage range of 3.0-4.8 V. DSC analysis also confirms the improved thermal stability attained by coating the cathode with Li₃PO₄-based materials.     

Mg-doped LiNi0.5Mn1.5O4 spinel for cathode materials

Lithium-ion batteries are becoming more and more important not only for portable electronic devices, but also in prevision of high power electric vehicles. In such an optic, deep studies regarding all the components of a secondary battery are in development. In this study, high voltage cathode materials have been selected. Crystals with spinel structure have a 3D vacancy pathway suitable for Li-ions transport. The material under study was LiNi_0.5Mn_1.5O₄ doped with magnesium replacing the nickel. Various samples were synthesized via three different routes: a solid-state method, a modified sol–gel method and a xerogel method. The structure and morphology of the powders were analyzed with HRTEM and XRD. Electrochemical tests were also performed. A wide range of particle sizes (from micro to nanosize) was the result of the different synthesis routes. Unfortunately pure materials were not always obtained. The electrochemical tests showed improvement of the material's cyclability, by reducing the particle size. The electrochemical tests further confirmed the existence of a Li_1+dMn_2−dO₄ impurity. The results are quite promising, however, further improvement of the purity of the electrode composition are needed.     

Synthesis and electrochemical performances of Li3V2(PO4)3/(Ag + C) composite cathode

Li₃V₂(PO₄)₃, Li₃V₂(PO₄)₃/C and Li₃V₂(PO₄)₃/(Ag + C) composites as cathodes for Li ion batteries are synthesized by carbon-thermal reduction (CTR) method and chemical plating reactions. The microstructure and morphology of the compounds are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The Li₃V₂(PO₄)₃/(Ag + C) particles are 0.5-1 μm in diameters. As compared to Li₃V₂(PO₄)₃, Li₃V₂(PO₄)₃/C, the Li₃V₂(PO₄)₃/(Ag + C) composite cathode exhibits high discharge capacity, good cycle performance (140.5 mAh g⁻¹ at 50th cycle at 1 C, 97.3% of initial discharge capacity) and rate behavior (120.5 mAh g⁻¹ for initial discharge at 5 C) for the fully delithiated (3.0-4.8 V) state. Electrochemical impedance spectroscopy (EIS) measurements show that the carbon and silver co-modification decreases the charge transfer resistance of Li₃V₂(PO₄)₃/(Ag + C) cathode, and improves the conductivity and boosts the electrochemical performance of the electrode.     

Synthesis and performance of carbon-coated Li3V2(PO4)3 cathode materials by a low temperature solid-state reaction

The carbon-coated monoclinic Li₃V₂(PO₄)₃ (LVP) cathode materials can be synthesized by a low temperature solid-state reaction route. The influences of different heat treatments on the LVP have been investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical methods. In the range of 3.0-4.3 V, both LVP/C electrodes present good rate capability and excellent cyclic performance. It is found that the sample (LVP1/C) prepared by the two-step heat treatment with pre-sintering at 350 °C delivers the initial discharge capacity of 99.8 mAh g⁻¹ at 10 C charge-discharge rate and still retains 95.8 mAh g⁻¹ after 300 cycles. For the sample (LVP2/C) synthesized by the one-step heat treatment, 95.9 and 90.0 mAh g⁻¹ are obtained in the 1st and 300th cycles at 10 C rate, respectively. Our results based on the XRD patterns and the SEM images suggest that the good rate capability and cyclic performance may be owing to the pure phases, small particles, large specific surface areas and residual carbon. In the range of 3.0-4.8 V, compared with the LVP2/C, the LVP1/C also exhibits better performance.     

Temperature-controlled microwave solid-state synthesis of Li3V2(PO4)3 as cathode materials for lithium batteries

Monoclinic Li₃V₂(PO₄)₃ can be rapidly synthesized at 750 °C for 5 min (MW5m) by using temperature-controlled microwave solid-state synthesis method (TCMS). The carbon-free sample MW5m presents well electrochemical properties. In the cut-off voltage 3.0-4.3, MW5m presents a charge capacity 132 mAh g⁻¹, almost equivalent to the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹), and discharge capacity 126.4 mAh g⁻¹. In the cut-off voltage 3.0-4.8 V, MW5m shows an initial discharge capacity of 183.4 mAh g⁻¹, near to the theoretical discharge capacity. In the cycle performance, the capacity fade of Li₃V₂(PO₄)₃ is dependent on the cut-off voltage and the preparation method.     

Nano-sized LiMn2O4 spinel cathode materials exhibiting high rate discharge capability for lithium-ion batteries

Nano-sized LiMn₂O₄ spinel with well crystallized homogeneous particles (60 nm) is synthesized by a resorcinol-formaldehyde route. Micro-sized LiMn₂O₄ spinel with micrometric particles (1 μm) is prepared by a conventional solid-state reaction. These two samples are characterized by XRD, SEM, TEM, BET, and electrochemical methods. At current rate of 0.2C (1C = 148 mA g⁻¹), a discharge capacity of 136 mAh g⁻¹ is obtained on the nano-sized LiMn₂O₄, which is higher than that of micro-sized one (103 mAh g⁻¹). Furthermore, compared to the micro-sized sample, nano-sized LiMn₂O₄ shows much better rate capability, i.e. a capacity of 85 mAh g⁻¹, 63% of that at 0.2C, is realized at 60C. The excellent high rate performance of nano-sized LiMn₂O₄ spinel may be attributed to its impurity-free nano-sized particles, higher surface area and well crystalline. The outstanding electrochemical performances demonstrate that the nano-sized LiMn₂O₄ spinel will be the promising cathode materials for high power lithium-ion batteries used in hybrid and electric vehicles.     

Surface modification of Li[Ni0.3Co0.4Mn0.3]O2 cathode by Li-La-Ti-O coating

A Li[Ni_0.3Co_0.4Mn_0.3]O₂ cathode is modified by applying a Li-La-Ti-O coating using the hydrothermal method. The coated Li[Ni_0.3Co_0.4Mn_0.3]O₂ is characterized by X-ray diffraction analysis, scanning electron microscopy, energy-dispersive spectrometry, transmission electron microscopy, and differential scanning calorimetry. The Li-La-Ti-O coating layer is formed as crystalline (perovskite structure) or amorphous phase depending on the heating temperature. The Li-La-Ti-O coated Li[Ni_0.3Co_0.4Mn_0.3]O₂ electrode has better rate capability than the pristine electrode. In particular, the rate capability is significantly associated with heating temperature; this is probably due to the phase of the coating layer. It appears that the Li-La-Ti-O coating of amorphous phase is superior to that of crystalline phase for obtaining enhanced rate capability of the coated samples. The thermal stability and cyclic performance of the Li[Ni_0.3Co_0.4Mn_0.3]O₂ electrode are also improved by Li-La-Ti-O coating. These improvements indicate that the Li-La-Ti-O coating is effective in suppressing the chemical and structural instabilities of Li[Ni_0.3Co_0.4Mn_0.3]O₂.     

Synthesis and electrochemical characterization of amorphous Li-Fe-P-B-O cathode materials for lithium batteries

Various types of amorphous Li-Fe-P-B-O were investigated for use as a cathode material. The samples were prepared by the melt quench technique with a single roll. The samples had monotonically decreasing charge-discharge profiles peculiar to amorphous materials, and were between 76 and 119 mAh g⁻¹. The electrochemical performance of these amorphous Li-Fe-P-B-O materials improved with increasing boron ratio, improving from 85 to 119 mAh g⁻¹. Although the redox potentials of amorphous Li-Fe-P-O did not shift with changing P/Fe ratio, those of amorphous Li-Fe-P-B-O did shift with changing B/P ratio. The redox potentials of the Li-Fe-P-B-O in the ratios of 2/1/2/0, 2/1/1/1, 2/1/0.5/1.5, and 2/1/0/2 were approximately 3.1, 2.9, 2.6, and 2.2 V vs. Li/Li⁺, respectively. This demonstrates that the redox potentials of amorphous polyanionic materials can be tuned by adjusting the electronegativity of the glass former, such as phosphorus and boron.