Effect of synthesis temperature on the properties of LiFePO4/C composites prepared by carbothermal reduction

LiFePO₄/C composite cathode materials were synthesized by carbothermal reduction method using inexpensive FePO₄ as raw materials and glucose as conductive additive and reducing agent. The precursor of LiFePO₄/C was characterized by differential thermal analysis and thermogravimetry. The microstructure and morphology of the samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscope (TEM) and particle size analysis. Cyclic voltammetry (CV) and charge/discharge cycling performance were used to characterize their electrochemical properties. The results showed that the LiFePO₄/C composite synthesized at 650 °C for 9 h exhibited the most homogeneous particle size distribution. Residual carbon during processing was coated on LiFePO₄, resulting in the enhancement of the material's electronic properties. Electrochemical measurements showed that the discharge capacity first increased and then decreased with the increase of synthesis temperature. The optimal sample synthesized at 650 °C for 9 h exhibited a highest initial discharge capacity of 151.2 mA h g⁻¹ at 0.2 C rate and 144.1 mA h g⁻¹ at 1 C rate with satisfactory capacity retention rate.     

A study on the electrochemical characteristics of LiFePO4 cathode for lithium polymer batteries by hydrothermal method

Phospho-olivine LiFePO₄ cathode materials were prepared by hydrothermal reaction at 150 °C. Carbon black was added to enhance the electrical conductivity of LiFePO₄. LiFePO₄-C powders (0, 3, 5 and 10 wt.%) were characterized by X-ray diffraction (XRD) and transmission electron microscope (TEM). LiFePO₄-C/solid polymer electrolyte (SPE)/Li cells were characterized electrochemically by charge/discharge experiments at a constant current density of 0.1 mA cm⁻² in a range between 2.5 and 4.3 V vs. Li/Li⁺, cyclic voltammetry (CV) and ac impedance spectroscopy. The results showed that initial discharge capacity of LiFePO₄ was 104 mAh g⁻¹. The discharge capacity of LiFePO₄-C/SPE/Li cell with 5 wt.% carbon black was 128 mAh g⁻¹ at the first cycle and 127 mAh g⁻¹ after 30 cycles, respectively. It was demonstrated that cycling performance of LiFePO₄-C/SPE/Li cells was better than that of LiFePO₄/SPE/Li cells.     

Cathode performance of olivine-type LiFePO4 synthesized by chemical lithiation

Chemical lithiation with LiI in acetonitrile was performed for amorphous FePO₄ synthesized from an equimolar aqueous suspension of iron powder and an aqueous solution of P₂O₅. An orthorhombic LiFePO₄ olivine structure was obtained by annealing a chemically lithiated sample at 550 °C for 5 h in Ar atmosphere. The average particle size remained at approximately 250 nm even after annealing. The lithium content in the sample was quantitatively confirmed by Li atomic absorption analysis and ⁵⁷Fe Mössbauer spectroscopy. While an amorphous FePO₄/carbon composite cathode has a monotonously decreasing charge–discharge profile with a reversible capacity of more than 140 mAh g⁻¹, the crystallized LiFePO₄/carbon composite shows a 3.4 V plateau corresponding to a two-phase reaction. This means that the lithium in the chemically lithiated sample is electrochemically active. Both amorphous FePO₄ and the chemically lithiated and annealed crystalline LiFePO₄ cathode materials showed good cyclability (more than 140 mAh g⁻¹ at the 40th cycle) and good discharge rate capability (more than 100 mAh g⁻¹ at 5.0 mA cm⁻²). In addition, the fast-charge performance was found to be comparable to that with LiCoO₂.     

Improved high-rate charge/discharge performances of LiFePO4/C via V-doping

V-doped LiFePO₄/C cathode materials were prepared through a carbothermal reduction route. The microstructure was characterized by X-ray diffraction, X-ray photoelectron spectroscopy and scanning electron microscopy. The electrochemical Li⁺ intercalation performances of V-doped LiFePO₄/C were compared with those of undoped one through galvanostatic intermittent titration technique, cyclic voltamperometry, and electrochemical impedance spectrum. V-doped LiFePO₄/C showed a high discharge capacity of ∼70 mAh g⁻¹ at the rate of 20 C (3400 mA g⁻¹) at room temperature. The significantly improved high-rate charge/discharge capacity is attributed to the increase of Li⁺ ion “effective” diffusion capability.     

Synthesis of carbon-coated LiFePO4 nanoparticles with high rate performance in lithium secondary batteries

A novel preparation technique was developed for synthesizing carbon-coated LiFePO₄ nanoparticles through a combination of spray pyrolysis (SP) with wet ball milling (WBM) followed by heat treatment. Using this technique, the preparation of carbon-coated LiFePO₄ nanoparticles was investigated for a wide range of process parameters such as ball-milling time and ball-to-powder ratio. The effect of process parameters on the physical and electrochemical properties of the LiFePO₄/C composite was then discussed through the results of X-ray diffraction (XRD) analysis, field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), the Brunauer-Emmet-Teller (BET) method and the use of an electrochemical cell of Li|1 M LiClO₄ in EC:DEC = 1:1|LiFePO₄. The carbon-coated LiFePO₄ nanoparticles were prepared at 500 °C by SP and then milled at a rotating speed of 800 rpm, a ball-to-powder ratio of 40/0.5 and a ball-milling time of 3 h in an Ar atmosphere followed by heat treatment at 600 °C for 4 h in a N₂ + 3% H₂ atmosphere. SEM observation revealed that the particle size of LiFePO₄ was significantly affected by the process parameters. Furthermore, TEM observation revealed that the LiFePO₄ nanoparticles with a geometric mean diameter of 146 nm were coated with a thin carbon layer of several nanometers by the present method. Electrochemical measurement demonstrated that cells containing carbon-coated LiFePO₄ nanoparticles could deliver markedly improved battery performance in terms of discharge capacity, cycling stability and rate capability. The cells exhibited first discharge capacities of 165 mAh g⁻¹ at 0.1 C, 130 mAh g⁻¹ at 5 C, 105 mAh g⁻¹ at 20 C and 75 mAh g⁻¹ at 60 C with no capacity fading after 100 cycles.     

Structural and electrochemical properties of Cl-doped LiFePO4/C

Cl-doped LiFePO₄/C cathode materials were synthesized through a carbothermal reduction route, and the microstructure and electrochemical performances were systematically studied. Cl-doped LiFePO₄/C cathode materials presented a high discharge capacity of ∼90 mAh g⁻¹ at the rate of 20 C (3400 mA g⁻¹) at room temperature. Electrochemical impedance spectroscopy and cyclic voltamperometry indicated the optimized electrochemical reaction and Li⁺ diffusion in the bulk of LiFePO₄ due to Cl-doping. The improved Li⁺ diffusion capability is attributed to the microstructure modification of LiFePO₄ via Cl-doping.     

A simple,cheap soft synthesis routine for LiFePO4 using iron(III) raw material

An order olivine structure LiFePO₄ was synthesized with a simple rheological phase reaction (RPR) of LiOH·H₂O and FePO₄·4H₂O in the presence of PEG as a reductive agent and carbon source. A required amount of water was added to the starting materials to form the rheological precursor and decomposed at 700 °C to form the crystalline phase LiFePO₄ directly, without ball-milling, preparation of intermediates, pre-sintering and post-deposition treatment. Fine particles with an average particle size about 216 nm are examined by scanning electron microscopy (SEM) and optical particle size analyzer. An initial discharge capacity of 157 mAh g⁻¹ was achieved for the as-prepared LiFePO₄ material with a rate of 0.1C (17 mA g⁻¹), what's more, this material shows excellent specific capacity, charge–discharge efficiency and cycle efficiency at high current rates, almost no capacity loss can be observed up to 40 cycles with the rate of 1, 2 and 3C at room temperature. The simple, cheap process as well as the excellent high-rate performance makes this RPR method feasible commercially.     

Optimized solid-state synthesis of LiFePO4 cathode materials using ball-milling

Olivine-type LiFePO₄ cathode materials were synthesized by a solid-state reaction method and ball-milling. The ball-milling time, heating time and heating temperature are optimized. A heating temperature higher than 700 °C resulted in the appearance of impurity phase Fe₂P and growth of large particle, which was shown by high resolution X-ray diffraction and field emission scanning electron microscopy. The impurity phase Fe₂P exhibited a considerable capacity loss at the 1st cycle and a gradual increase in discharge capacity upon cycling. Moreover, it exhibited an excellent high-rate capacity of 104 mAh g⁻¹ at 3 C in spite of the large particle size. The optimum synthesis conditions for LiFePO₄ were ball-milling for 24 h and heat-treatment at 600 °C for 3 h. LiFePO₄/Li cells showed an enhanced cycling performance and a high discharge capacity of 160 mAh g⁻¹ at 0.1 C.     

Synthesis of LiFePO4/C composite with high-rate performance by starch sol assisted rheological phase method

LiFePO₄/C composite was synthesized at 600 °C in an Ar atmosphere by a soluble starch sol assisted rheological phase method using home-made amorphous nano-FePO₄ as the iron source. XRD, SEM and TEM observations show that the LiFePO₄/C composite has good crystallinity, ultrafine sphere-like particles of 100-200 nm size and in situ carbon. The synthesized LiFePO₄ could inherit the morphology of FePO₄ precursor. The electrochemical performance of the LiFePO₄ by galvanostatic cycling studies demonstrates excellent high-rate cycle stability. The Li/LiFePO₄ cell displays a high initial discharge capacity of more than 157 mAh g⁻¹ at 0.2C and a little discharge capacity decreases from the first to the 80th cycle (>98.3%). Remarkably, even at a high current density of 30C, the cell still presents good cycle retention.     

Effects of carbon coating and iron phosphides on the electrochemical properties of LiFePO4/C

Carbon coated LiFePO₄ (LiFePO₄/C) with different contents of high electron conductive iron phosphide phase was synthesized by an aqueous sol–gel method in a reductive sintering atmosphere. Different synthesis parameters were used for adjusting the microstructure and phase compositions of the products. The effects of the carbon coating and iron phosphides on the electrochemical properties of the LiFePO₄/C electrodes were studied by means of testing the discharge capacities at rates of 0.1–5C (1C = 170 mAh g⁻¹) and analyzing the CV curves. The results show that carbon coating in a content of 1.5 wt.% derived from the carbon source of ethylene glycol greatly decreases the particle size of LiFePO₄ in one order in the specific surface area, and significantly improves the rate capability of LiFePO₄. The effect of the content of FeP on the capacity of the carbon coated LiFePO₄ was different at different discharge rates. Increasing the content of FeP from 1.2 to 3.7 wt.% slightly decreases the capacity of LiFePO₄/C at low discharge rate (0.1C and 1C), but obviously increases the capacity of LiFePO₄/C when the discharge rate is increased to 5C. For the carbon free sample, even it also has 1.8 wt.% FeP, it still possesses poor capacity due to the large particle size of LiFePO₄ and the lack of conductivity. And too much iron phosphides lowers the discharge capacity of the electrode since they are inert for the deinsertion/insertion of lithium ion.     

Preparation and electrochemical properties of La0.4Sr0.6FeO3 as negative electrode of Ni/MH batteries

Perovskite-type oxide La_0.4Sr_0.6FeO₃ powder was prepared by a stearic acid combustion method, and its phase structure, kinetic characteristics, and electrochemical properties were systematically investigated as the negative electrode for Ni/MH batteries. X-ray diffraction (XRD) shows that the as-prepared powder consists of a single phase with rhombohedral structure. After 20 cycles, perovskite-type structure still remains in the electrode sample. The electrochemical test shows that the reaction at the La_0.4Sr_0.6FeO₃ electrode is reversible. With an increase in temperature from 298 K to 333 K, its initial discharge capacities increase from 153.4 mA h g⁻¹ to 502.6 mA h g⁻¹ at 31.25 mA g⁻¹, and from 56.0 mA h g⁻¹ to 279.6 mA h g⁻¹ at 125 mA g⁻¹, respectively. At a discharge current density of 125 mA g⁻¹, its capacities keep steady at about 80.0 mA h g⁻¹, 195 mA h g⁻¹ and 370 mA h g⁻¹ at 298 K, 313 K and 333 K, respectively. Both the exchange current density and the proton diffusion coefficient of the La_0.4Sr_0.6FeO₃ oxide electrode also increase with temperature in a manner similar to the discharge capacity.     

Electrochemical properties of magnesium-based hydrogen storage alloys improved by transition metal boride and silicide additives

Transition metal borides and silicides prepared by mechanical alloying (MA) and chemical reduction methods (CR) were introduced to improve the corrosion resistance of magnesium-based hydrogen storage alloys. The additive of FeB prepared by MA can remarkably enhance the discharge capacity and cycling stability which has initial discharge capacity of 355.9 mA h g⁻¹ and keeps 224 mA h g⁻¹ after 100 cycles, and the exchange density I₀ of MgNi–NiB(CR) electrodes is 344.80 mA g⁻¹ but MgNi is only 67.6 mA g⁻¹ which leads to the better rate capability of the composite alloys. The results of SEM characterization, cyclic charge–discharge tests, potentiodynamic polarization, linear polarization and AC impedance experiment show that the corrosion inhibition property of MgNi in alkaline is improved by transition metal boride and silicide additives.     

Improved electrochemical performances of 9LiFePO4·Li3V2(PO4)/C composite prepared by a simple solid-state method

9LiFePO₄·Li₃V₂(PO₄)₃/C is synthesized via a carbon thermal reaction using petroleum coke as both reduction agent and carbon source. The as-prepared material is not a simple mixture of LiFePO₄ (LFP) and Li₃V₂(PO₄)₃ (LVP), but a composite possessing two phases: one is V-doped LFP and the other is Fe-doped LVP. The typical structure enhances the electrical conductivity of the composite and improves the electrochemical performances. The first discharge capacity of 9LFP·LVP/C in 18650 type cells is 168 mAh g⁻¹ at 1 C (1 C_9LFP·LVP/C = 166 mA g⁻¹), and exhibits high reversible discharge capacity of 125 mAh g⁻¹ at 10 C even after 150 cycles. At the temperature of −20 °C, the reversible capacity of 9LFP·LVP/C can maintain 75% of that at room temperature.     

Novel synthesis of LiFePO4-Li3V2(PO4)3 composite cathode material by aqueous precipitation and lithiation

LiFePO₄-Li₃V₂(PO₄)₃ composite cathode material is synthesized by aqueous precipitation of FeVO₄·xH₂O from Fe(NO₃)₃ and NH₄VO₃, following chemical reduction and lithiation with oxalic acid as the reducer and carbon source. Samples are characterized by XRD, SEM and TEM. XRD pattern of the compound synthesized at 700 °C indicates olivine-type LiFePO₄ and monoclinic Li₃V₂(PO₄)₃ are co-existed. TEM image exhibits that LiFePO₄-Li₃V₂(PO₄)₃ particles are encapsulated with a carbon shell 5-10 nm in thickness. The LiFePO₄-Li₃V₂(PO₄)₃ compound cathode shows good electrochemical performance, and its discharge capacity is about 139.1 at 0.1 C, 135.5 at 1 C and 116 mA h g⁻¹ at 3 C after 30 cycles.     

A new low-temperature synthesis and electrochemical properties of LiV3O8 hydrate as cathode material for lithium-ion batteries

LiV₃O₈, synthesized from V₂O₅ and LiOH, by heating of a suspension of V₂O₅ in a LiOH solution at a low-temperature (100-200 °C), exhibits a high discharge capacity and excellent cyclic stability at a high current density as a cathode material of lithium-ion battery. The charge-discharge curve shows a maximum discharge capacity of 228.6 mAh g⁻¹ at a current density of 150 mA g⁻¹ (0.5 C rate) and the 100 cycles discharge capacity remains 215 mAh g⁻¹. X-ray diffraction indicates the low degree of crystallinity and expanding of inter-plane distance of the LiV₃O₈ phase, and scanning electronic microscopy reveals the formation of nano-domain structures in the products, which account for the enhanced electrochemical performance. In contrast, the LiV₃O₈ phase formed at a higher temperature (300 °C) consists of well-developed crystal phases, and coherently, results in a distinct reduction of discharge capacity with cycle numbers. Thus, an enhanced electrochemical performance has been achieved for LiV₃O₈ by the soft chemical method via a low-temperature heating process.     

A novel method for synthesis of layered LiNi1/3Mn1/3Co1/3O2 as cathode material for lithium-ion battery

The layered LiNi_1/3Mn_1/3Co_1/3O₂ materials with good crystalline are synthesized by a novel method of hydrothermal method followed by a short calcination process. The crystalline structure and morphology of the synthesized materials are characterized by XRD, SEM. Their electrochemical performances are evaluated by CV, EIS and galvonostatic charge/discharge tests. The material synthesized at 850 °C for 6 h shows the highest initial discharge capacity of 187.7 mAh g⁻¹ at 20 mA g⁻¹. And the capacity retention of 97.9% is maintained at the end of 40 cycles at 1.0 C. CV test reveals almost no shift of anodic and cathodic peaks after first cycle, which indicates good reversible deintercalation and intercalation of Li⁺ ions.     

Electrochemical performance of nanostructured amorphous Co3Sn2 intermetallic compound prepared by a solvothermal route

A nanostructured amorphous Co₃Sn₂ intermetallic compound was prepared by a solvothermal route. The microstructure and the electrochemical performance were studied by X-ray diffraction (XRD), transmission electron microscopy (TEM), galvanostatic cycling, and ex situ XRD. It was found that the as-prepared material is in nanoscale and is amorphous. The amorphous Co₃Sn₂ shows a first specific capacity of 363 mA h g⁻¹ compared to 92 mA h g⁻¹ for the crystalline one prepared by annealing the amorphous material. Ex situ XRD investigation shows that the amorphous Co₃Sn₂ undergoes a crystallization process during cycling, which leads to the capacity fade.     

Effect of annealing on the electrochemical properties of ramsdellite-type lithium titanium oxide

Lithium titanium oxide (LTO) with a ramsdellite structure is an advantageous anode for lithium ion secondary batteries, because of its positive potential, which is beneficial for safety reasons. In addition, compared with other titanate anodes, it has a superior theoretical capacity of 321 mA h g⁻¹, which is close to the capacity of a practical carbonaceous anode. Our study showed that this ramsdellite-type LTO had a high discharge capacity that is stable at 250 mA h g⁻¹ at a current density of 1 mA cm⁻². However, this high capacity is only achieved by employing as-synthesized ramsdellite LTO powder. When the same powder was stored and the same evaluation was carried out, the resulting capacity was 200 mA h g⁻¹, which is lower than the capacity of as-synthesized powder. An annealing applied to the ramsdellite LTO powder appeared to restore the capacity loss after storage. Annealing at 250 °C for 5 h produced the best performance, which was even better than that obtained using the as-synthesized ramsdellite LTO powder. Moreover, we investigated the surface property of ramsdellite LTO and found that the presence of a carbon derivative is apparently responsible for blocking the Li ions insertion/extraction, and thus reducing the capacity.     

Effect of mechanical activation process parameters on the properties of LiFePO4 cathode material

Pure, nano-sized LiFePO₄ and carbon-coated LiFePO₄ (LiFePO₄/C) positive electrode (cathode) materials are synthesized by a mechanical activation process that consists of high-energy ball milling and firing steps. The influence of the processing parameters such as firing temperature, firing time and ball-milling time on the structure, particle size, morphology and electrochemical performance of the active material is investigated. An increase in firing temperature causes a pronounced growth in particle size, especially above 600 °C. A firing time longer than 10 h at 600 °C results in particle agglomeration; whereas, a ball milling time longer than 15 h does not further reduce the particle size. The electrochemical properties also vary considerably depending on these parameters and the highest initial discharge capacity is obtained with a LiFePO₄/C sample prepared by ball milling for 15 h and firing for 10 h at 600 °C. Comparison of the cyclic voltammograms of LiFePO₄ and LiFePO₄/C shows enhanced reaction kinetics and reversibility for the carbon-coated sample. Good cycle performance is exhibited by LiFePO₄/C in lithium batteries cycled at room temperature. At the high current density of 2C, an initial discharge capacity of 125 mAh g⁻¹ (73.5% of theoretical capacity) is obtained with a low capacity fading of 0.18% per cycle over 55 cycles.