Selection of anionic exchange resins for removal of natural organic matter (NOM) fractions

Early elimination of natural organic matter (NOM) by ion exchange (IEX) in water treatment is expected to improve subsequent water treatment processes and the final drinking water quality. Nine anionic exchange resins were investigated to remove NOM and specific NOM fractions determined by liquid chromatography in combination with organic carbon detection (LC-OCD) and fluorescence excitation-emission matrices (EEM). Breakthrough of NOM was predicted by model calculations using Freundlich isotherms and IEX rate experiments. The time to breakthrough varied from 4 to 38 days. Removal of specific NOM fractions proved to vary considerably for the different types of IEX resins, ranging from 1% to almost 60%. The removal of NOM fractions, specifically humic substances, increased with an increase in water content of the investigated IEX resins and with a decrease in resin size. The best-performing IEX resins consisted of the smallest resins and/or those with the highest water content. The worst-performing IEX resins reflected the highest exchanging capacities and the lowest water contents.     

Identification of nanofiltration membrane foulants

The Mery-sur-Oise plant (France) has been using nanofiltration (NF) membranes (NF200) to produce safe drinking water since 1999. However, significant fouling has been occasionally observed according to seasonal conditions, even with various pre-treatments including conventional surface water treatment followed by ozonation, acid addition to pH 6.9, anti-scalant addition, and microfiltration (6mum). Pilot-scale filtration experiments were performed to determine the effects of natural organic matter (NOM) character and ozonation on NF membrane fouling under constant operating conditions. Two parallel pilot units were operated with sand-filtered water (SFW) and sand-filtered-ozonated water (SFOW) for 3-month periods corresponding to spring and fall seasons. To identify NF foulants, Fourier transform infrared spectroscopy, fluorescence excitation emission matrix, scanning electron microscope, energy-dispersive spectrophotometry, and HPSEC-UVA-DOC-fluorescence chromatography have been used. Even though the dissolved organic carbon (DOC) and ultraviolet (UVA) levels of spring samples were lower than those of winter season, these feed waters showed higher fouling presumably due to a higher hydrophilic fraction of NOM and the presence of microorganisms. In addition, for both seasons, ozonation increased the degree of fouling mainly by a change in NOM characteristics and by the promotion of bacterial cell growth conditions. The hydrophilic NOM is not expected to be easily rejected by the relatively hydrophilic and negatively charged NF200 membrane due to its non-charged (or oppositely charged) properties, indicating a high fouling potential by NOM associated with spring samples. The adhesion of bacteria and accumulation of microalgae on the membrane may be due to the role of extracellular biopolymers released by algae upon ozonation, promoting adhesion between microorganisms and the membrane surface. Protein- and polysaccharide-like substances were found as major foulants. The reason for the minor fouling by humic substances on membranes fed with SFOW during the spring season might be a loss of membrane surface charge due to screening by significant subsequent fouling on the base of the fouling layer of extracellular materials.     

Influence of interactions between NOM and particles on UF fouling mechanisms

This study focused on the mechanistic effects of molecular interactions between inorganic particles (kaolinite) and the two main NOM fouling fractions of polysaccharides (alginate) and humics (humic acids) in ultrafiltration. Fouling effects were studied during the dead-end filtration of individual and mixed compounds as well as during the subsequent filtration of individual compounds. SEM analyses were performed to further study the fouling-layer structure. A significant synergistic effect was observed during combined particle-NOM fouling, which was considerably greater than the sum of particle and organic fouling alone. Synergistic fouling could be explained by NOM-particle interactions in the feed solution and during the fouling process. Kaolinite alone formed a fouling layer of particle aggregates, whereas humic acid adsorption onto kaolinite resulted in a fouling layer of stabilized colloids of humic acid and kaolinite. In the case of alginate, simultaneous pore-blocking and cake-layer formation of NOM and kaolinite dominated the fouling. In both cases, incorporation of the organics in the kaolinite fouling layer resulted in a fouling cake of significantly reduced porosity compared to individual particle filtration. Irreversible fouling by NOM could not be prevented by kaolinite. SEM images showed patches of the particle-fouling layer remaining on the membrane surface after backwashing, which can be linked to particle-membrane associations by NOM bridging.     

Characterizing algogenic organic matter (AOM) and evaluating associated NF membrane fouling

Occasional algal blooms, comprised of blue-green algae and/or green algae, cause significant challenges in drinking water treatment due to the release of algogenic organic matter (AOM) into water extracellularly and, upon cell lysis, intracellularly. AOM has been extracted from blue-green algae (cyanobacteria) by various means and analyzed by UV absorbance scanning, HPSEC-UV-fluorescence-DOC, UV absorbance ratio index (URI), FTIR, and fluorescence excitation emission matrix (EEM). AOM extracted in water as a solvent exhibited a high hydrophilic fraction (57.3%) with a low SUVA (1.0 L/m-mg). The molecular weight (MW) distribution showed a significant heterogeneity (high value of polydispersivity) and high protein content (as indicated by specific fluorescence). Significant amounts of proteinaceous components such as mycosporine-like amino acids (MAAs, UV-screening components) and phycobilins (light-harvesting pigment) were detected by UV/visible absorption. The presence of proteins was confirmed by FTIR (at 1661 and 1552 cm(-1)), EEM spectra (EX:278-282 nm and EM:304-353 nm), and high URI values (3.1-6.0). A bench-scale cross-flow unit, employing a flat-sheet membrane specimen, was used to examine nanofiltration (NF) membrane fouling and removal of natural organic matter (NOM) derived from different blends of Suwannee River humic acid (SRHA) and AOM: SRHA 10 mgC/L, AOM 3mg C/L + SRHA 7 mgC/L, AOM 7 mgC/L + SRHA 3 mgC/L, and AOM 10 mgC/L. The study focused mainly on the effects of two different sources of organic matter on NF (NF 200) membrane fouling under otherwise similar conditions. Flux decline and organic matter rejection as a function of delivered DOC (cumulative mass of feed DOC per unit area) showed significantly different results depending on the organic matter composition of samples even though the test conditions were the same (organic matter concentration, pH, temperature, inorganic salt composition and concentration, and recovery). A higher flux decline was observed with increasing proportions of AOM. Organic matter rejections also decreased with higher AOM contributions to the samples, indicating that lower molecular weight (MW) AOM components were not well rejected by the NF 200 membrane having a 360 Da MWCO. However, SRHA that exhibited a relatively high MW (1000-5000 Da range) and high SUVA (7.4 L/m-mg) was preferentially rejected through electrostatic repulsion/size exclusion by the NF 200 membrane, having a high negative charge, low MWCO, and relatively low hydrophobicity. Even though the DOC concentration of feed water is a decisive factor for membrane fouling along with membrane properties and operating conditions, the characteristics of organic matter are more influential in fouling potential. Protein-like and polysaccharide-like substances were found as major foulants by FTIR.     

A hybridized photocatalysis-microfiltration system with iron oxide-coated membranes for the removal of natural organic matter in water treatment: Effects of iron oxide layers and colloids

A photocatalysis/microfiltration (MF) hybrid system, with the coating of a membrane using iron oxide particles (IOPs), was investigated with respect to natural organic matter (NOM) removal and membrane permeability during the treatment of various surface waters. A comparison of the performance between bare (uncoated) and IOP-coated membranes employed for the photocatalytic hybrid system was made. Due to the additional adsorption of NOM onto IOPs on the membrane surface, the IOP-coated membrane system always achieved greater DOC removal efficiencies during photocatalysis/MF. Particularly, the influence of colloidal particles that were present in different water sources with respect to membrane fouling was explored. Colloidal fouling occurred to both bare and IOP-coated membranes, but the interaction of colloids with IOP coating layers was in close association with the characteristics of colloids, such as size distribution, resulting in opposing fouling behaviors with varying water sources. The IOP-coated membrane was able to control fouling properly when a relatively large size of colloidal particles existed in raw water, but not for the case of small colloids. The IOP coat layer may become denser as small colloids penetrate into it, therefore leading to further fouling. The analysis of the hydraulic filtration resistances revealed that such fouling was virtually reversible in being removed by backwashing processes. Scanning electron microscopic observations, however, visualized the existence of several foulants remaining at the membrane surface after backwashing when feed water, containing a relatively large portion of small-sized colloids, was supplied.     

Identification and understanding of fouling in low-pressure membrane (MF/UF) filtration by natural organic matter (NOM)

An understanding of natural organic matter (NOM) as a membrane foulant and the behavior of NOM components in low-pressure membrane fouling are needed to provide a basis for appropriate selection and operation of membrane technology for drinking water treatment. Fouling by NOM was investigated by employing several innovative chemical and morphological analyses.

Source (feed) waters with a high hydrophilic (HPI) fraction content of NOM resulted in significant flux decline. Macromolecules of a relatively hydrophilic character (e.g. polysaccharides) were effectively rejected by low-pressure membranes, suggesting that macromolecular compounds and/or colloidal organic matter in the hydrophilic NOM fraction may be a problematic foulant of low-pressure membranes. Moreover, the significant organic fouling that is contributed by polysaccharides and/or proteins in macromolecular and/or colloidal forms depends on molecular shape (structure) as well as size (i.e. molecular weight). More significant flux decline was observed in microfiltration (MF) compared to ultrafiltration (UF) membrane filtration. MF membrane fouling may be caused by pore blockage associated with large (macromolecular) hydrophilic molecules and/or organic colloids. In the case of UF membranes, the flux decline may be caused by sequential or simultaneous processes of surface (gel layer) coverage during filtration. Morphological analyses support the notion that membrane roughness may be considered as a more important factor in membrane fouling by controlling interaction between molecules and the membrane surface, compared to the hydrophobic/hydrophilic character of membranes. Membrane fouling mechanisms are not only a function of membrane type (MF versus UF) but also depend on source (feed) water characteristics.     

Interplay of different NOM fouling mechanisms during ultrafiltration for drinking water production

Ultrafiltration is an emerging technology for drinking water production, but a main challenge remains the lack of understanding about fouling. This paper investigates the impact of molecular interactions between different natural organic matter (NOM) compounds on ultrafiltration fouling mechanisms. We performed dead-end filtration experiments with individual and mixed humic acid and alginate (polysaccharide). Alginate showed detrimental, but mostly reversible, flux decline and high solute retention. Our results indicate that this was caused by pore blocking transformed into cake building and weak molecular foulant-membrane and foulant-foulant interactions. In the presence of calcium, aggravated fouling was observed, related to complexation of alginate and its subsequently induced gel formation. With humic acid, more severe irreversible fouling occurred due to humic acid adsorption. Minor adsorption of alginate onto the membrane was also observed, which probably caused the substantial irreversible flux decline. The fouling characteristics in the mixtures reflected a combination of the individual humic acid and alginate experiments and we conclude, that the individual fouling mechanisms mutually influence each other. A model elucidates this interplay of the individual fouling mechanisms via hydrophobic and electrostatic interactions. In our study such an interplay resulted in an alginate cake, or gel in the presence of calcium, which is relatively irreversibly adsorbed onto the membrane by humic acid associations. This study shows the importance of mutual influences between various foulants for improved understanding of fouling phenomena. Furthermore it shows that substances with a minor individual influence might have a large impact in mixed systems such as natural water.     

Transition in fouling mechanism in microfiltration of a surface water

The main disadvantage of membrane filtration is membrane fouling, which remains as the major obstacle for more efficient use of this technology. Information about the constituents that cause fouling is indispensable for more efficient operation. We examined the changes in both foulant characteristics and membrane morphology by performing the pilot-scale filtration test using one microfiltration membrane. During the operation, we cut the membrane fibers three times, and the components that caused irreversible fouling were extracted by acid or alkaline solution. We found that the characteristic of inorganic matter extracted by acid solution completely differed depending on the filtration period. A large amount of iron was extracted in the second chemical cleaning, while manganese was the dominant component of the extracted inorganic matter in the third chemical cleaning. The analysis of Fourier transform infrared (FTIR) and cross polarization magic angle spinning carbon-13 (CPMAS (13)C) nuclear magnetic resonance (NMR) demonstrated that the contribution of humic substances and carbohydrate in the organic foulant had increased as fouling developed. The changes in the major foulant have no relation with the fluctuation in feed water. The analysis of membrane morphology illustrated that the cake layer started to build up after the blockage of membrane pores. Based on the above results, we hypothesized the following fouling mechanism: the pores were covered or narrowed with relatively large particles such as iron, carbohydrate or protein; small particles such as manganese or humic substances blocked the narrowed pores; and finally an irreversible cake layer started to build up on the membrane surface.     

Assessing PAC contribution to the NOM fouling control in PAC/UF systems

This paper investigates the powdered activated carbon (PAC) contribution to the fouling control by natural organic matter (NOM) in PAC/UF hybrid process, as well as the foulant behaviour of the PAC itself. Solutions of NOM surrogates (humic acids, AHA, and tannic acid, TA) and AOM/EOM (algogenic organic matter/extracellular organic matter) fractions from a Microcystis aeruginosa culture were permeated through an ultrafiltration (UF) hollow-fibre cellulose acetate membrane (100 kDa cut-off). The greatest impairment on flux and the poorest rejection were associated with polysaccharide-like EOM substances combined with mono and multivalent ions. PAC, either in the absence or in the presence of NOM, did not affect the permeate flux nor the reversible membrane fouling, regardless of the NOM characteristics (hydrophobicity and protein content) and water inorganics. However, PAC controlled the irreversible membrane fouling, minimising the chemical cleaning frequency. Furthermore, PAC enhanced AHA and TA rejections and the overall removal of AOM, although it was apparently ineffective for the highly hydrophilic EOM compounds.     

Characterising humic acid fouling of nanofiltration membranes using bisphenol A as a molecular indicator

Fouling of nanofiltration (NF) membranes by humic acids was investigated using bisphenol A (BPA) as an indicator chemical to differentiate between various mechanisms that may lead to a change in solute rejection. Three commercially available NF membranes were investigated and an accelerated fouling condition was achieved with a foulant mixture containing humic acids in an electrolyte matrix. The effects of membrane fouling on the rejection of BPA were interpreted with respect to the membrane pore sizes and the fouling characteristics. Results reported here indicate that calcium concentration in the feed solution could be a major factor governing the humic acid fouling process. Moreover, a critical concentration of calcium in the feed solution was observed, at which membrane fouling was most severe. Membrane fouling characteristics were observed by their influence on BPA rejection. Such influence could result in either an increase or decrease in rejection of BPA by the three different membranes depending on the rejection mechanisms involved. It is hypothesized that these mechanisms could occur simultaneously and that the effects of each might not be easily distinguished. However, it was observed that their relative contribution was largely dependent upon membrane pore size. Pore blocking, which resulted in a considerable improvement in rejection, was prominent for the more open pore size TFC-SR2 membrane. In contrast, the cake-enhanced concentration polarisation effect was more severe for the tighter NF-270 and NF-90 membranes. For hydrophobic solutes such as BPA, the formation of the fouling layer could also interfere with the solute-membrane interaction, and therefore, exert considerable influence on the separation process.     

Reversible and irreversible low-pressure membrane foulants in drinking water treatment: Identification by principal component analysis of fluorescence EEM and mitigation by biofiltration pretreatment

With the increased use of membranes in drinking water treatment, fouling - particularly the hydraulically irreversible type - remains the main operating issue that hinders performance and increases operational costs. The main challenge in assessing fouling potential of feed water is to accurately detect and quantify feed water constituents responsible for membrane fouling. Utilizing fluorescence excitation-emission matrices (EEM), protein-like substances, humic and fulvic acids, and particulate/colloidal matter can be detected with high sensitivity in surface waters. The application of principal component analysis to fluorescence EEMs allowed estimation of the impact of surface water constituents on reversible and irreversible membrane fouling. This technique was applied to experimental data from a two year bench-scale study that included thirteen experiments investigating the fouling potential of Grand River water (Ontario, Canada) and the effect of biofiltration pre-treatment on the level of foulants during ultrafiltration (UF). Results showed that, although the content of protein-like substances in this membrane feed water (= biofiltered natural water) was much lower than commonly found in wastewater applications, the content of protein-like substances was still highly correlated with irreversible fouling of the UF membrane. In addition, there is evidence that protein-like substances and particulate/colloidal matter formed a combined fouling layer, which contributed to both reversible and irreversible fouling. It is suggested that fouling transitions from a reversible to an irreversible regime depending on feed composition and operating time. Direct biofiltration without prior coagulant addition reduced the protein-like content of the membrane feed water which in turn reduced the irreversible fouling potential for UF membranes. Biofilters also decreased reversible fouling, and for both types of fouling higher biofilter contact times were beneficial.     

Influence of electrostatic interactions on the rejection with NF and assessment of the removal efficiency during NF/GAC treatment of pharmaceutically active compounds in surface water

The removal efficiency of several pharmaceutically active compounds from two different surface water types was investigated. Two different nanofiltration (NF) membranes (Trisep TS-80 and Desal HL) were first studied at low feed water recoveries (10%). In a second phase, the combination of an NF unit at higher feed water recovery (80%) with subsequent granular activated carbon (GAC) filtration of the permeate was investigated. Results indicate that removal of the selected pharmaceuticals with NF is mainly influenced by charge effects: negatively charged solutes are better removed, compared with uncharged solutes, which are, in turn, better removed compared with positively charged solutes. This latter trend is mainly due to charge attractions between the negatively charged membrane surface and positively charged solutes. Increasing feed concentrations of positively charged pharmaceuticals lead to increasing rejection values, due to membrane charge-shielding effects. The removal efficiency of pharmaceuticals with the combination NF/GAC is extremely high. This is mainly due to an increased adsorption capacity of the activated carbon since the largest part of the natural organic matter (NOM) is removed in the NF step. This NOM normally competes with pharmaceuticals for adsorption sites on the carbon.     

Polymeric compounds in activated sludge supernatant -- Characterisation and retention mechanisms at a full-scale municipal membrane bioreactor

In this study, for the first time a full-scale membrane bioreactor (MBR) was investigated with focus on organic compounds in activated sludge over a period of approximately 2 years. Soluble extracellular polymeric substances (EPS) in the sludge supernatant and permeate as well as bound EPS extracted from fouled membranes were determined photospectrometrically and revealed a typical composition of three main components in the order metals>humic acids>carbohydrates>proteins. Results showed an important influence on membrane fouling by soluble humic substances and carbohydrates in complexes with metal cations. It was found that Fe(2+) and Fe(3+) play a decisive role in natural organic matter (NOM) complexation and subsequent membrane blockage. The determination of molar mass distribution in supernatant and permeate by size exclusion chromatography (SEC) revealed a significant retention of macromolecular compounds by the porous membranes in the range of 10-50%.     

Impact of humic acid fouling on membrane performance and transport of pharmaceutically active compounds in forward osmosis

The impact of humic acid fouling on the membrane transport of two pharmaceutically active compounds (PhACs) – namely carbamazepine and sulfamethoxazole – in forward osmosis (FO) was investigated. Deposition of humic acid onto the membrane surface was promoted by the complexation with calcium ions in the feed solution and the increase in ionic strength at the membrane surface due to the reverse transport of NaCl draw solute. The increase in the humic acid deposition on the membrane surface led to a substantial decrease in the membrane salt (NaCl) permeability coefficient but did not result in a significant decrease in the membrane pure water permeability coefficient. As the deposition of humic acid increased, the permeation of carbamazepine and sulfamethoxazole decreased, which correlated well with the decrease in the membrane salt (NaCl) permeability coefficient. It is hypothesized that the hydrated humic acid fouling layer hindered solute diffusion through the membrane pore and enhanced solute rejection by steric hindrance, but not the permeation of water molecules. The membrane water and salt (NaCl) permeability coefficients were fully restored by physical cleaning of the membrane, suggesting that humic acid did not penetrate into the membrane pores.     

Studies on the effect of humic acids and phenol on adsorption-ultrafiltration process performance

Application of pressure-driven membrane processes, such as ultrafiltration (UF) and microfiltration (MF) for surface water treatment have become very popular during last decades. Membrane fouling by humic substances (HS) is one of the major limiting factors in these processes. In order to alleviate the unfavorable effects of the presence of HS in the feed on the process performance UF and MF are often combined with adsorption on powdered activated carbon (PAC). The main goal of the present study was to evaluate the effect of humic acid (HA) on membrane fouling during UF. Moreover, the effect of PAC addition to the feed on UF process, especially on flux decline was determined. The applicability of the adsorption-ultrafiltration (PAC/UF) system to purification of water containing low (phenol) and high molecular (HA) was also investigated. Three different polymer UF membranes, prepared from polysulfone (PSF), cellulose acetate (CA) or polyacrylonitrile (PAN) were applied. It was found that the membranes prepared from PSF and CA are very susceptible to fouling caused by HA. The permeate flux decreased for ca. 50% during UF of HA solution through the PSF membrane and for ca. 45%-through the CA membrane. In the case of the PAN membrane, a negligible effect of HA on the flux was observed. On the basis of the FTIR spectra it was found that the drop in the permeate flux through these membranes may result from interactions between the negatively charged functional groups present on the membrane surface, such as carboxyl groups (CA) and sulfone groups (PSF) with HA, which results in coating of the membrane surface with HA. When PAC was added to the feed containing HA, the permeate flux through the CA and PAN membranes was maintained on a practically unchanged level. However, in case of the PSF membrane, a 50% drop in the permeate flux in comparison with the flux value, when process was conducted without PAC addition was observed. That was supposed to be due to attractive forces among hydrophobic PAC particles, HA molecules and PSF membrane surface. The performed studies showed that the application of PAC/UF system was very effective in the removal of organic substances having both, low and high molecular weights. The role of PAC suspended in a feed in the PAC/UF system is the adsorption of low molecular organic compounds, which cannot be removed by UF alone.     

Degradation of natural organic matter by TiO2 photocatalytic oxidation and its effect on fouling of low-pressure membranes

Natural organic matter (NOM) fouling continues to be the major barrier to efficient application of microfiltration (MF) and ultrafiltration (UF) in drinking water treatment. In this study, the potential of TiO2/UV photocatalytic oxidation to control fouling of membranes by NOM was evaluated. Decomposition kinetics of NOM was investigated using a commercial TiO2 catalyst, and the effect of various experimental parameters including TiO2 dosage and initial total organic carbon (TOC) concentration were also determined. The reaction kinetics was found to increase with increasing TiO2 dosage, but decrease with increasing initial TOC concentration. Even though the rate of TOC removal was relatively low, the TiO2/UV process was very effective in controlling membrane fouling by NOM. At a TiO2 concentration of 0.5 g/L, fouling of both an MF and a UF membrane was completely eliminated after 20 min of treatment. Careful analyses of specific UV absorbance (SUVA) and molecular weight (MW) distribution of NOM revealed that the effectiveness in membrane fouling control is the result of the changes in NOM molecular characteristics, namely MW and SUVA due to the preferential removal and transformation of large, hydrophobic NOM compounds. Results from this study show that TiO2/UV photocatalytic oxidation is a promising pretreatment method for MF and UF systems.     

Extracellular polymeric substances (EPS) properties and their effects on membrane fouling in a submerged membrane bioreactor

A pilot-scale submerged membrane bioreactor (MBR) for real municipal wastewater treatment was operated for over one year in order to investigate extracellular polymeric substances (EPS) properties and their role in membrane fouling. The components and properties of bound EPS were examined by the evaluation of mean oxidation state (MOS) of organic carbons, Fourier transform infrared (FT-IR) spectroscopy, three-dimensional excitation-emission matrix (EEM) fluorescence spectroscopy, and gel filtration chromatography (GFC), etc. Test results showed that MOS of organic carbons in the bound EPS was ranging from −0.14 to −0.51, and major components could be assessed as proteins and carbohydrates. FT-IR analysis confirmed the presence of proteins and carbohydrates in the bound EPS. The organic substances with fluorescence characteristics in the bound EPS were identified as proteins, visible humic acid-like substances and fulvic acid-like substances by EEM technology. GFC analysis demonstrated that EPS had part of higher MW molecules and a broader MW distribution than the influent wastewater. It was also found that a high shear stress imposed on mixed liquor could result in the release of EPS, which would in turn influence membrane fouling in MBRs. Bound EPS solution was observed to have a stronger potential of fouling than mixed liquor. During long-term operation of the MBR, bound EPS demonstrated positive correlations with membrane fouling while temperature was verified as a negative factor affecting EPS concentration. Compared to tightly bound EPS (TB-EPS), loosely bound EPS (LB-EPS) showed more significant correlations with membrane fouling. This critical investigation would contribute towards a better understanding of the behavior, composition and fouling potential of EPS in MBR operation.     

Quantitative biofouling diagnosis in full scale nanofiltration and reverse osmosis installations

Biofilm accumulation in nanofiltration and reverse osmosis membrane elements results in a relative increase of normalised pressure drop (ΔNPD). However, an increase in ΔNPD is not exclusively linked to biofouling. In order to quantify biofouling, the biomass parameters adenosine triphosphate (ATP), total cell count and heterotrophic plate count in membrane elements were investigated during membrane autopsies and compared with ΔNPD in test rigs and 15 full scale investigations with different types of feed water. The combination of biomass related parameters ATP and total cell count in membrane elements seem to be suitable parameters for diagnosis of biofouling, whereas plate counts were not appropriate to assess biofouling. The applied ΔNPD measurement was too insensitive for early detection of fouling. Measurements of biological parameters in the water were shown to be not appropriate in quantifying biofouling. Evidently, there is a need for a practical tool, sensitive pressure drop data and systematic research.     

Comparison of humic acid rejection and flux decline during filtration with negatively charged and uncharged ultrafiltration membranes

Increasingly stringent regulations for drinking water quality have stimulated the ultrafiltration (UF) to become one of the best alternatives replacing conventional drinking water treatment technologies. However, UF is not very effectively to remove humic acid due to the comparatively larger pore size compared to the size of humic acid. Fouling issue is another factor that restricts its widespread application. In this study, rejection of humic acid and flux decline were compared with essentially neutral, negatively charged version of a regenerated cellulose membrane, in which electrostatic interaction was explored for a better humic acid removal and less fouling. Solution environment, including ionic strength, pH and calcium ion concentration, affecting humic acid removal and flux decline on negatively charged and neutral membranes was also compared. Results indicated that the appropriate charge modification on the neutral UF membrane could be an effective way for better removal of NOM and reduction of the membrane fouling due to the electrostatic interactions with the combination effect of membrane pore size. Electrostatic interactions are significant important to achieve high humic acid removal and less fouling, and to improve the water quality and protect people’s health.     

Effects of Natural Organic Matter, Anthropogenic Surfactants, and Model Quinones on the Reduction of Contaminants by Zero-Valent Iron

Recent studies of contaminant reduction by zero-valent iron metal (Fe⁰) have highlighted the role of iron oxides at the metal–water interface and the effect that sorption has at the oxide–water interface on contaminant reduction kinetics. The results suggest that a variety of organic surface-active substances might enhance or inhibit contaminant degradation, depending on the degree to which they promote solubilization, sorption, and/or reaction. Of particular interest is the effect of natural organic matter (NOM), because of its ubiquitous presence in natural waters and amphiphilic properties; anthropogenic surfactants, because of their use in groundwater remediation; and certain quinones, which represent the redox-active functional groups associated with NOM. In this study, no well-defined effects of these substances were found on the reduction of nitro benzene by Fe⁰, but the reduction of carbon tetrachloride and trichloroethylene (TCE) was inhibited by NOM. Results with carbon tetrachloride showed that the inhibitory effect of humic acids was greater than fulvic acids, but that several quinonoid NOM model compounds (juglone, lawsone, and anthraquinone disulfonate) increased the rate of reduction by Fe⁰. Isotherms for adsorption of TCE and NOM onto Fe⁰ showed evidence of competition for surface sites.