In situ reaction synthesis and characterization of Ti3Si(Al)C2/SiC composites

The reaction route, microstructure, and properties of Ti₃Si(Al)C₂/SiC composites with 5–30 vol.% SiC content prepared by in situ hot pressing/solid–liquid reaction synthesis process are investigated. In contrast to monolithic Ti₃Si(Al)C₂, the SiC particle-reinforced composites exhibit higher elastic modulus, Vickers hardness, fracture toughness, improved wear, and oxidation resistance, but have a slight loss in flexural strength. The improvement in the properties is mainly ascribed to the contribution of SiC particles, and the strength degradation is due to the residual tensile stresses in the matrix.     

Direct selective extraction of titanium silicide Ti5Si3 from multi-component Ti-bearing compounds in molten salt by an electrochemical process

Titanium silicide (Ti₅Si₃) has been extracted directly from complex Ti-bearing compounds by electro-deoxidation. A pressed cylindrical pellet of the multi-component compounds acted as a cathode, and carbon-saturated liquid metal contained in a solid-oxide oxygen-ion-conducting membrane (SOM) tube served as an anode. This electrochemical process was carried out in a molten CaCl₂ system at 950–1050 °C and 3.5–4.0 V. The parameters of electrolysis and the electrolytic characteristics were investigated, and the morphology and phase composition of the final products were examined. Ti₅Si₃ was directly extracted from Ti-bearing compounds. Electrolysis time, applied potential, and electrolysis temperature are the dominant factors that affect the characteristics of the final products. The mechanisms of the extraction of Ti₅Si₃ and the removal of metallic elements (Ca, Mg, and Al) are suggested based on our experimental results and theoretical analysis. The optimal conditions of the electrolysis are a temperature of ∼1050 °C and a potential of 3.5–4.0 V, which result in rapid reduction and good product morphology. The excellent oxidation resistance of the extracted Ti₅Si₃ is confirmed.     

The preparation of Mg3Si2O5(OH)4 nanotubes under solvothermal conditions

With magnesium carbonate hydroxide and nanoporous silica as the starting materials, chrysotile (Mg₃Si₂O₅(OH)₄) nanotubes were prepared by using a solvothermal method at 400^∘C within four hours. This new method needs no strong alkali medium and the reaction time is very short. EDX analysis showed a molar ratio of 3Mg:2Si:9O of the product. Selected Area Electron Diffraction (SAED) pattern indicated that the tube axis is along [100] direction. HRTEM image showed the nanotubes were multi-walled and the distance between the two close layers was about 0.75 nm, which is very near to the distance of {001} planes. Thus, combining the results of SAED and HRTEM, we can conclude that the {001} planes of serpentine roll up along the [100] direction to form the tubular structure. The effects of various reaction conditions and the formation mechanism were also discussed.     

Rapid synthesis of Ti3AlC2/TiB2 composites by the spark plasma sintering (SPS) technique

Dense Ti₃AlC₂/TiB₂ composites were successfully fabricated from B₄C/TiC/Ti/Al powders by spark plasma sintering (SPS). The microstructure, flexural strength and fracture toughness of the composites were investigated. The experimental results indicate that the Vickers hardness increased with the increase in TiB₂ content. The maximum flexural strength (700 ± 10 MPa) and fracture toughness (7.0 ± 0.2 MPa m^1/2) were achieved through addition of 10 vol.% TiB₂, however, a slight decrease in the other mechanical properties was observed with TiB₂ addition higher than 10 vol.%, which is believed to be due to TiB₂ agglomeration.     

Laser machining of Al2O3-ZrO2 (3%Y2O3) eutectic composite

In this work we present the study of the interaction between NIR pulsed laser and Al₂O₃-ZrO₂ (3%Y₂O₃) eutectic composite. The effect produced by modifying the reference position as well as the working conditions and laser beam features has been studied when the samples are processed by means of pulse bursts.The samples were obtained by the laser floating zone technique using a CO₂ laser system. The laser machining was carried out with a Q-switched Nd:YAG laser at its fundamental wavelength of 1064 nm with pulse-widths in the nanosecond range.Geometric dimensions, i.e. ablated depth, machined width and removed volume as well as ablation yield of the resulting holes have been studied. We have described and discussed the morphology, composition and microstructure of the processed samples.     

氯化 Ti3AlC2 陶瓷制备碳化物衍生碳的结构表征

以三元碳化物陶瓷Ti_3AlC_2为原料,在500°C~1000°C温度范围内氯化制备具有纳米孔结构的碳化物衍生碳(Ti_3AlC_2-CDC)。高温氯化制备得到的Ti_3AlC_2-CDC由无定形碳和石墨组成。氯化温度越高,石墨化程度越明显,石墨有序度越高。Ti_3AlC_2-CDC的结构与前驱体Ti_3AlC_2的层状结构保持一致。但随着温度升高,Ti_3AlC_2-CDC会逐渐裂解为单片层或多片层。采用N2吸附技术研究了700°C、800°C和1000°C下制备的Ti_3AlC_2-CDC的孔隙结构特征,通过分析试样的吸附等温线特征和孔径分布探讨了温度对CDC孔结构的影响。     

Luminescence properties of Eu activated Ba2Si5N8 red phosphors with various Eu contents

This study was carried out to characterize the crystal structure and luminescence properties of Eu²⁺ doped red-emitting Ba₂Si₅N₈ phosphor. In this research, Ba₂Si₅N₈ phosphors with various Eu compositions were prepared by normal pressure sintering (NPS). Ba₃N₂, Si₃N₄ and Eu₂O₃ were sintered at a high temperature in a mixture of N₂ and H₂. The crystal structure was analyzed by X-ray diffraction(XRD), and the photoluminescence(PL) properties of the Eu²⁺ - activated Ba₂Si₅N₈ phosphors were evaluated as a function of the Eu²⁺ activator concentration. The red-emitting Ba₂Si₅N₈ phosphors showed a broad excitation band range as well as high quantum output.     

Comparative study of Li(Li1/3Ti5/3)O4 and Li(Ni1/2−xLi2x/3Tix/3)Ti3/2O4 (x = 1/3) anodes for Li rechargeable batteries

A solid solution of spinel (2/3)Li(Li_1/3Ti_5/3)O₄–(1/3)Li(Ni_1/2Ti_3/2)O₄ was prepared, and its structural/electrochemical properties were compared with Li(Li_1/3Ti_5/3)O₄ to identify the effect of doping to the structural invariance of Li(Li_1/3Ti_5/3)O₄. The solid solution retained the zero strain characteristic of Li(Li_1/3Ti_5/3)O₄ during discharge/charge with an excellent cycle stability, while the rate capability was notably improved. However, a reversible broadening of the XRD peak was observed at the end of discharge, indicating some structural changes. XANES measurements showed that the oxidation state of Ti was +4 and that of Ni was +2 in the solid solution.     

In situ synthesis,mechanical and cyclic oxidation properties of Ti3AlC2/Al2O3 composites

ABSTRACT

Ti₃AlC₂/Al₂O₃ composite materials were successfully fabricated from TiO₂/TiC/Ti/Al powders by the in situ reactive hot pressed technique. The microstructure, mechanical and oxidation properties of the composites were investigated in the paper. Vickers hardness increased with the Al₂O₃ content. The relative density of Ti₃AlC₂/Al₂O₃ composites exhibits a declining tendency with Al₂O₃ content especially exceeds 10 vol.?%. The Ti₃AlC₂/Al₂O₃ composites show excellent electrical conductivity. The flexural strength and fracture toughness of Ti₃AlC₂/10 vol. % Al₂O₃ are 461 ± 20?MPa and 6.2?±?0.2?MPa m^1/2, respectively. The cyclic oxidation behaviour of resistance of Ti₃AlC₂/10 vol. % Al₂O₃ composites at 800–1000°C generally obeys a parabolic law. The oxide scale of sample consists of a mass of α-Al₂O₃ and TiO₂, forming a dense and adhesive protect layer. The result indicates that the Al₂O₃ can greatly improve the oxidation resistance of Ti₃AlC₂.     

Material removal and surface damage in EDM of Ti3SiC2 ceramic

Material removal and surface damage of Ti₃SiC₂ ceramic during electrical discharge machining (EDM) were investigated. Melting and decomposition were found to be the main material removal mechanisms during the machining process. Material removal rate was enhanced acceleratively with increasing discharge current, i_e, working voltage, u_i, but increased deceleratively with pulse duration, t_e. Microcracks in the surface and loose grains in the subsurface resulted from thermal shock were confirmed, and the surface damage in Ti₃SiC₂ ceramic led to a degradation of both strength and reliability.     

Effect of Al2O3 on mechanical properties of Ti3SiC2/Al2O3 composite

The effect of Al₂O₃ on mechanical properties of Ti₃SiC₂/Al₂O₃ composite fabricated by SPS was studied systematically. The results show that the hardness of the Ti₃SiC₂/Al₂O₃ composite can reach 10.28 GPa, 50% higher than that of pure Ti₃SiC₂. However, slight decrease in the other mechanical properties was observed with Al₂O₃ addition higher than 5–10 vol.%, which is believed to be due to the agglomeration of Al₂O₃ in the composite.     

Effect of TiO2 doped Ni electrodes on the dielectric properties and microstructures of (Ba0.96Ca0.04)(Ti0.85Zr0.15)O3 multilayer ceramic capacitors

The effects of TiO₂-doped Ni electrodes on the microstructures and dielectric properties of (Ba_0.96Ca_0.04)(Ti_0.85Zr_0.15)O₃ multilayer ceramic capacitors (MLCCs) have been investigated. Nickel paste with a TiO₂ dopant was used as internal electrodes in MLCCs based on (Ba_0.96Ca_0.04)(Ti_0.85Zr_0.15)O₃ (BCTZ) ceramic with copper end-termination. The microstructures and defects were analysed by microstructural techniques (SEM/HRTEM) and energy-dispersive spectroscopy (EDS). The continuity of the electrode of the MLCC was measured using a scanning electron microscope, which showed that the continuity of the electrode for the MLCC with a TiO₂-doped Ni electrode was approximately 90%. However, continuity of the electrode for a conventional MLCC was below 80%. The continuity of the TiO₂-doped Ni electrode showed significant improvement in the MLCC, which was due to no reaction between Ni and BCTZ.     

Metal-organic framework Cu3 (BTC)2(H2O)3 catalyzed Aldol synthesis of pyrimidine-chalcone hybrids

A typical metal organic framework, [Cu₃ (BTC)₂(H₂O)₃, BTC = 1,3,5-benzene tricarboxylate] has been used for the synthesis of pyrimidine-chalcones. We have explored a green synthesis of pyrimidine chalcones under Cu₃(BTC)₂ catalysis by Aldol condensation. Easy isolation of product, excellent yield, and recyclable catalyst makes this reaction eco-friendly. The technology was demonstrated to be applicable to the synthesis of a host of chemical hybrids.     

The intercalation of C60-containing PEO into layered MnPS3

This paper reports the synthesis and magnetism of a new polymer-inorganic intercalation nanocomposite based on a C₆₀-containing poly(ethylene oxide) (C₆₀-PEO) into layered MnPS₃, which is characterized by XRD, IR and thermal analyses. The lattice expansion (Δd) of the intercalation nanocomposite is about 9.3 Å indicating the successful intercalation. And the charge balance is maintained by K⁺ ions coordinating with PEO chain of C₆₀-PEO polymer, which come from the pre-intercalation compound Mn_1−xPS₃[K_2x(H₂O)_y]. Magnetic measurements indicate that the intercalation nanocomposite (C₆₀-PEO/MnPS₃) exhibits a magnetic phase transition from paramagnetism to ferrimagnetism at about 40 K. And the distinctive hysteresis of M-H relationship further confirms that it is a low temperature ferrimagnetic nanocomposite.     

Room temperature multiferroic properties of Ni-doped Aurivillus phase Bi5Ti3FeO15

Single-phase Aurivillius Bi₅Ti₃Fe_0.5Ni_0.5O₁₅ (BTFN) ceramics were synthesized by the solid-state reaction method. The substitution of Ni for half Fe ions does not introduce magnetic impurity phase but increases magnetic moment more than two orders. The ferroelectric and magnetic Curie temperatures are determined to be 1100 K and 726 K. The room-temperature multiferroic behavior of the BTFN ceramics were demonstrated by the ferroelectric (2P_r=8.5 μC/cm², 2E_c=74 kV/cm) and ferromagnetic (2M_r=27.86 m emu/g, 2H_c=553 Oe) measurements. The ferromagnetism can be ascribed to the aggregation of magnetic ions at the inner octahedra by Ni doping and the spin canting of magnetic-ion-based sublattices via the Dzyaloshinskii-Moriya interaction. The present work suggests the possibility of doped Bi₅Ti₃FeO₁₅ as a potential room-temperature multiferroic.     

The effect of Al(OH)3 coating on the Li[Li0.2Ni0.2Mn0.6]O2 cathode material for lithium secondary battery

Layered Li[Li_0.2Ni_0.2Mn_0.6]O₂ powder was modified by coating its surface with amorphous Al(OH)₃. Energy dispersive spectroscopy (EDS) showed that nano-sized Al(OH)₃ powders were homogeneously dispersed in the parent Li[Li_0.2Ni_0.2Mn_0.6]O₂ powders. Al(OH)₃ coated Li[Li_0.2Ni_0.2Mn_0.6]O₂ exhibited an greater retention capacity at higher rates compared to uncoated Li[Li_0.2Ni_0.2Mn_0.6]O₂. The low area specific impedance (ASI) value of the Al(OH)₃ is the major factor for its higher rate performance. The 1.4 wt.% Al(OH)₃ coated sample had an impedance of 41 Ω cm² while uncoated Li[Li_0.2Ni_0.2Mn_0.6]O₂ had a 57 Ω cm² at 30-80% state of charge. Electrochemical impedance spectroscopy (EIS) also showed that the Al(OH)₃ coated sample had a lower charge transfer resistance (R_ct) than the uncoated sample. Differential scanning calorimetry (DSC) analysis showed that Al(OH)₃ coating improved the thermal stability. Al(OH)₃ coating increased the onset temperature of thermal decomposition and reduced the amount of heat for the exothermic peak.     

Influence of the Type of Reducing Agent (H2, CO, C3H6 and C3H8) on the Reduction of Stored NOX in a Pt/BaO/Al2O3 Model Catalyst

In this investigation, a comparative study for a NO _X storage catalytic system was performed focusing on the parameters that affect the reduction by using different reductants (H₂, CO, C₃H₆ and C₃H₈) and different temperatures (350, 250 and 150 °C), for a Pt/BaO/Al₂O₃ catalyst. Transient experiments show that H₂ and CO are highly efficient reductants compared to C₃H₆ which is somewhat less efficient. H₂ shows a significant reduction effect at relatively low temperature (150 °C) but with a low storage capacity. We find that C₃H₈does not show any NO _X reduction ability for NO _X stored in Pt/BaO/Al₂O₃ at any of the temperatures. The formation of ammonia and nitrous oxide is also discussed.     

Effects of grinding and firing conditions on CaAl2Si2O8 phase formation by solid-state reaction of kaolinite with CaCO3

The effects of grinding and firing conditions on CaAl₂Si₂O₈ phase formation by solid-state reaction of kaolinite with CaCO₃ were investigated by differential thermal analysis (DTA)–thermogravimetry (TG), X-ray powder diffraction (XRD) and ²⁹Si and ²⁷Al MAS NMR. Unground and ground samples showed similar crystallization behavior at about 850 °C, and the crystallizing temperature was relatively unaffected by grinding. On the other hand, the crystalline products were strongly influenced by the grinding. Gehlenite (Ca₂Al₂SiO₇) was the dominant phase in the unground samples but layer-structured CaAl₂Si₂O₈ was dominant in the ground samples, together with a small amount of anorthite, which is the stable phase. The amount of anorthite gradually increased with higher firing temperature, the sample fired at 1000 °C being almost completely anorthite. Grinding treatment before firing was effective in accelerating the decomposition of CaCO₃ and extending the temperature range for the formation of CaAl₂Si₂O₈, a phase with local structure similar to that of layered CaAl₂Si₂O₈.     

Thermal shock resistance of in situ formed Si2N2O–Si3N4 composites by gelcasting

Thermal shock resistance of Si₂N₂O–Si₃N₄ composites was evaluated by water quenching and subsequent three-point bending tests of strength diminution. Si₂N₂O–Si₃N₄ composites which was prepared with in situ liquid pressureless sintering process using Yb₂O₃ and Al₂O₃ powders as sintering additives by gelcasting showed no macroscopic cracks and the critical temperature difference (ΔT_c) could be up to 1400 °C. A mass of pores existed in the sintered body and the irregular shaped fibers extended from the pores increased the thermal shock property.     

Oxidation behavior and kinetics of in situ (TiB2 + TiC)/Ti3SiC2 composites in air

The isothermal oxidation behavior of in situ (TiB₂ + TiC)/Ti₃SiC₂ composite ceramics with different TiB₂ content has been investigated at 900-1200 °C in air for exposure times up to 20 h by means of X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, and energy dispersive spectroscopy. The oxidation of (TiB₂ + TiC)/Ti₃SiC₂ composites follows a parabolic rate law. With the increase in TiB₂ content, the oxidation weight gain, thickness of the oxidation scale, and parabolic rate constant decrease dramatically, which suggests that the incorporation of TiB₂ greatly improves the oxidation resistance of the composites. With the increase in oxidation temperature, the enhancement effect becomes more pronounced. Due to the incorporation of TiB₂, the oxidation scale of (TiB₂ + TiC)/Ti₃SiC₂ composites is generally composed of an outer layer of coarse-grained TiO₂ and an inner layer of amorphous boron silicate and fine-grained TiO₂. Only the dense inner layer formed on the surface acts as a diffusion barrier, retarding the inward diffusion of O, and consequently contributing to the improved oxidation resistance of the (TiB₂ + TiC)/Ti₃SiC₂ composites.