超声疲劳试验方法对S06钢疲劳性能及裂纹萌生机制的影响

采用超声疲劳试验方法和试样尺寸相近的高频疲劳试验方法对S06钢进行疲劳性能试验,将试验数据和试样断口形貌进行对比,研究超声疲劳试验方法对S06钢疲劳性能和裂纹萌生机制的影响.结果表明:在相同的应力水平下,超声加载频率下S06钢的疲劳寿命高于高频疲劳试验测得的疲劳寿命;超声疲劳试验中裂纹全部从表面萌生,而高频疲劳试样裂纹有表面萌生和内部萌生两种机制.分析了超声加载频率对S06钢疲劳性能和裂纹萌生机制产生影响的原因:对疲劳性能的影响与金属材料的晶体结构和裂纹尖端的化学反应有关,对裂纹萌生机制的影响与试样表层残余应力松弛有关.     

考虑结构裂纹扩展的振动疲劳寿命计算方法

工程实践中任何结构都存在不同程度的裂纹损伤,振动激励下动响应与疲劳裂纹扩展之间互相耦合,直接影响结构振动疲劳寿命.为了考虑结构振动疲劳耦合效应对疲劳寿命的影响,提出了一种考虑结构裂纹扩展的振动疲劳寿命计算方法.分析时,通过建立若干个含不同长度裂纹的结构有限元模型模拟结构裂纹扩展,采用Paris方程分段计算结构振动疲劳裂纹扩展寿命,通过试验确定的固有频率降变化规律反推结构裂纹萌生寿命,最后累计得到结构疲劳总寿命.结论表明,仿真计算结果与试验结果比较吻合.     

TC4钛合金复合加载下超高周疲劳性能研究EI北大核心CSCD

针对航空发动机压气机叶片在实际工况下的超高周疲劳断裂问题,研究了三种锻造温度下TC4钛合金三点弯曲–轴向拉伸复合加载的疲劳破坏行为。试验结果表明,S-N曲线呈直线下降型和双平台型,采用985℃近锻造时疲劳性能最好。随着应力幅值降低,裂纹由表面萌生向次表面萌生转变,断口形貌呈现准解理断裂特征。表面裂纹萌生于α晶界或α-β相界,由位错滑移堆积导致;而次表面裂纹萌生于刻面,由初生α相解理导致。疲劳寿命由裂纹萌生阶段主导,且所占比例随总寿命的增加而变大。双态组织中初生α含量和尺寸均小于等轴组织,且β转变组织含量更高,从而具备更好的疲劳性能。轴向拉伸改变了试件的轴向应力分布,有利于提高裂纹萌生于次表面的概率,使裂纹起源点向内部迁移。     

变形镁合金AZ80的腐蚀疲劳机理

根据挤压镁合金AZ80人工时效热处理(T5-177℃,16 h)前后分别在空气和NaCl介质中的疲劳寿命,研究了变形镁合金的腐蚀疲劳机理以及β相在腐蚀疲劳中的作用.结果表明:时效可导致AZ80组织β相体积分数增加、拉伸强度和硬度提高,可明显地提高在低应力水平下的腐蚀疲劳寿命.在空气中,疲劳裂纹萌生于表层和亚表面中的夹杂物;而在腐蚀介质中,腐蚀疲劳微裂纹萌生于试样表面的腐蚀坑,点蚀坑萌生于与β相相邻的α相.疲劳断口可见河流花样、二次裂纹、韧窝,具有解理特征.阳极溶解是挤压镁合金AZ80的腐蚀疲劳机制.     

挤压镁合金AM60的腐蚀疲劳

研究了加载频率、溶液pH值、氯离子浓度和氟化物转化膜等对挤压镁合金AM60疲劳寿命的影响,讨论了疲劳机理及AlMn相的作用.结果表明:在空气中10 Hz以下,疲劳寿命与频率有一定的关系;而在10 Hz以上,疲劳寿命与频率无关.AM60在中性溶液中疲劳寿命最短,在碱性溶液中疲劳寿命最长.氯离子能明显地降低疲劳寿命,含氟转化膜提高腐蚀疲劳寿命的作用不明显.断口分析表明,挤压镁合金AM60疲劳裂纹的形成与AlMn相粒子有关.在空气中,疲劳裂纹源为AlMn相粒子;而在溶液介质中,腐蚀疲劳裂纹萌生于AlMn相粒子周围的点蚀坑.     

离心叶轮叶片裂纹产生原因分析

某发动机离心叶轮叶片的排气边多处出现裂纹,通过理化检验和定量分析对裂纹产生原因进行了分析,并估算了叶片的裂纹扩展寿命及其占总寿命的百分比。结果表明:该裂纹为高低周复合疲劳裂纹,叶片在异常振动等大应力作用下产生了疲劳开裂。     

低周疲劳下16MnR微孔的裂纹萌生与扩展

采用宏观与微观结合的方法,在疲劳试验机上进行疲劳试验,在光学显微下观察裂纹的起裂与扩展.研究了压力容器用钢16MnR在低周疲劳下微孔(40～200μm)的裂纹萌生与扩展规律.研究表明裂纹的萌生机制:滑移带启裂和疏松带启裂,前者由剪应力起主要作用,后者由正应力起主要作用.而滑移带的局部性和裂纹开叉是低周疲劳下微裂纹的两大典型现象.微观缺陷尺寸、应力水平对疲劳寿命有显著影响,当应力水平较低时,微孔尺寸对寿命的影响明显.而当应力水平较高时(超过屈服极限),孔径对寿命的影响不敏感.在同一应力水平下,微缺陷尺寸存在临界值dt,当d＞dt时,疲劳寿命下降很多.     

汽轮机转子钢常温与600℃超高周疲劳行为研究

利用自主研发的高温超声疲劳实验系统,开展Cr Mo W转子钢常温及600℃下的超高周疲劳实验。为新型超超临界汽轮机转子提供高温超高周疲劳数据,实验结果表明高温会极大降低转子钢的疲劳强度。S-N曲线在常温及600℃下均呈现连续下降型,且600℃下S-N曲线在整个疲劳寿命周次内保持一定下降趋势。断口分析发现,常温下疲劳寿命107周次试件的疲劳裂纹以内部萌生为主,600℃下疲劳破坏的内部夹杂萌生方式与表面萌生方式均分布于整个疲劳寿命。夹杂物尺寸分析表明,高温降低疲劳裂纹内部萌生夹杂物的临界尺寸。     

颗粒和微观结构对Cu/WCp复合材料疲劳裂纹萌生和扩展行为的影响

通过原位扫描电子显微镜(SEM)研究了粉末冶金制备的Cu/WCp复合材料的疲劳裂纹萌生和扩展行为,分析了颗粒和微观结构对Cu/WCp复合材料疲劳裂纹萌生和早期扩展行为的影响。结果表明:疲劳微裂纹萌生于WCp颗粒和基体Cu的界面;微裂纹之间相互连接并形成主裂纹,当主裂纹和颗粒相遇时裂纹沿着颗粒界面扩展。在低应力强度因子幅ΔK区域疲劳小裂纹具有明显的"异常现象",并占据了全寿命的71%左右。疲劳小裂纹的早期扩展阶段易受局部微观结构和颗粒WCp的影响,扩展速率波动性较大,随机性较强;当小裂纹长度超过150μm时,裂纹扩展加快直至试样快速断裂。裂纹偏折、分叉和塑性尾迹降低了疲劳裂纹扩展速率,而颗粒界面脱粘则提高了复合材料的疲劳裂纹扩展速率。通过数值模拟也可以发现颗粒脱粘增大了材料的疲劳扩展驱动力,从而提高了疲劳裂纹扩展速率。     

缺口对7A85铝合金拉伸性能和疲劳性能的影响

在光滑试样表面预制深度为0.1 mm和0.2 mm的环状缺口，研究了不同缺口尺寸对7A85铝合金拉伸性能和疲劳性能的影响，并分析了7A85铝合金含缺口试样的疲劳断裂机理。结果表明，随着缺口深度由0 mm增加至0.2 mm, 7A85铝合金试样的抗拉强度、断后伸长率和疲劳强度分别下降了6%、47.5%、44.4%。缺口对7A85铝合金塑性的影响远大于拉伸强度，且其抗拉强度与疲劳强度呈线性关系。试样疲劳缺口系数随着缺口尺寸和循环次数的增加而增大。7A85铝合金试样的疲劳裂纹源通常是富铁的第二相颗粒，环状缺口根部应力集中促进了多疲劳裂纹源萌生，多个裂纹源同时扩展使得试样有效承载面积快速减少，导致疲劳寿命急剧缩短。     

Fatigue crack initiation in Ti–5Al–4Sn–2Zr–1Mo–0.7Nd–0.25Si high temperature titanium alloy

Ti–5Al–4Sn–2Zr–1Mo–0.7Nd–0.25Si alloy is a new high temperature titanium alloy for aeroengine use. In this paper, the fatigue crack initiation in this alloy was investigated. At applied maximum nominal stresses less than 500 MPa, most cracks initiate in the matrix away from the Nd-rich particles. Initiation of these cracks is related to the cracking of equiaxed α phase on the prior β grain boundaries. At high applied stresses, almost half of the cracks initiate in the matrix away form the Nd-rich particles and the other half initiate near Nd-rich particles. The probability that an Nd-rich particle initiates a fatigue crack decreases very rapidly as the particle size falls below 12 μm.     

Characteristics of Faigue Crack Initiation in Ti-5Al-4Sn-2Zr-1Mo-0.7Nd-0.25Si Alloy

The characteristics of fatigue crack initiation in Ti-5AI-4Sn-2Zr1Mo-O.7Nd-O.25Si alloy wereStudied. Two modes Of fatigue crack initiation were found. The Nd-rich phase particles displaybetter resistance to fatigue crack initiation than the matrix at lower stress.     

镍基单晶合金涡轮叶片开裂原因

某发动机高压涡轮叶片为镍基单晶合金叶片,在室温下进行振动疲劳试验后发现叶片开裂,通过宏观观察、金相检验和扫描电镜分析等方法对叶片开裂的原因进行了分析。结果表明:进气边叶根和榫头伸根的开裂形式均为疲劳开裂;进气边叶根气膜孔内壁存在多处小缺口及榫头伸根亚表面存在疏松缺陷,这些缺陷部位容易形成裂纹源,促进了裂纹的萌生,裂纹扩展后最终导致开裂失效。     

Fatigue crack initiation behaviors throughout friction stir welded joints in AA7075-T6 in ultrasonic fatigue

This paper presents the results of experimental investigation on fatigue behaviors of friction stir welded joints in AA7075-T6 with ultrasonic fatigue test system (20 kHz). Two kinds of particles, Fe-rich intermetallic compounds and Mg₂Si-based particles, governed the fatigue crack initiation. The plastic deformation and recrystallization during welding process led to the changes in particle size and micro crack occurrence between thermo-mechanically affected zone (TMAZ) and nugget zone (NZ). Therefore, the fatigue crack initiation sites leaned to be located at the TMAZ in short fatigue life, or at the NZ in very high cycle fatigue regime.     

发动机三级涡轮叶片断裂分析

某发动机三级涡轮转子叶片在飞机赶快冰爬升时断裂，通过断口ＳＥＭ观察，ＥＤＡＸ成分分析，叶片基材金相检验和硬度测试等分析了叶片的断裂原因和机制，结果表明，共振是叶片失稳断裂的直接原因，热疲劳萌生裂纹，高温腐蚀疲劳控制裂纹稳态扩展，材料冶金缺陷对叶片断裂过程有促进作用。     

Evaluation of corrosion fatigue crack propagation life at low-pressure steam turbine rotor groove

The corrosion fatigue crack propagation life of Christmas-tree type rotor groove with three hooks is studied. Each corner of the hook can be a candidate for crack initiation site therefore the condition where cracks initiate and propagate simultaneously at several hook corners must be considered. When a blade is inserted in the rotor groove, narrow gap is introduced unavoidably between the rotor groove and the blade root. The effect of this narrow gap on the crack behavior must also be considered. A procedure was presented to assess the crack initiation and propagation behavior under such a condition. Using the procedure, crack initiation and propagation behavior was evaluated for several gap conditions. It was revealed that the gap condition had little effect on the relation between crack depth at the third hook corner and life consumption ratio (ratio of loading cycle to final failure life). A corrosion fatigue test was performed using a rotor groove model specimen, and the results were compared with the evaluation results.     

Investigation of microstructure effect on fretting fatigue crack initiation using crystal plasticity

The onset of fretting fatigue is characterized by material microstructural changes in which the extent of the damage is comparable to grain size, and hence, the microstructure characteristics could have a significant effect on fatigue crack initiation. In this paper, a three‐dimensional finite element crystal plasticity framework is presented for simulation of the fretting fatigue. Controlled Poisson Voronoi tessellation (CPVT) method is employed to generate the polycrystalline region. In the CPVT method, regularity parameter controls the shape of grains. In this study, the impact of grain size and regularity parameter on crack initiation life and initiation site has been investigated. Cumulative plastic slip was used as a parameter of microstructure‐sensitive fatigue indicator. This parameter could effectively predict the location of crack initiation and its life. The results show that regularity parameter has a significant effect on the location of crack initiation. Furthermore, the effect of grain size on the fretting fatigue life of 316L stainless steel was investigated experimentally through testing different specimens with different grain sizes, to validate the simulation results.     

Numerical stress and crack initiation analysis of the compressor blades after foreign object damage subjected to high-cycle fatigue

This paper presents results of the complex stress and crack initiation analysis of the PZL-10 W turbo-engine compressor blade subjected to high cycle fatigue (HCF). A nonlinear finite element method was utilized to determine the stress state of the blade during the first mode of transverse vibration. In this analysis, the numerical models without defects and also with V-notches were defined. The quality of the numerical solution was checked by the convergence analysis. Obtained results were next used as an input data into crack initiation (ε–N) analyzes performed for the load time history equivalent to one cycle of the transverse vibration. In the fatigue analysis the different methods such as: Neuber elastic–plastic strain correction, linear damage summation and Palmgreen–Miner rule were utilized. As a result of ε–N analysis, the number of load cycles to the first fatigue crack appearing in the compressor blades was obtained. Moreover, the influence of the blade vibration amplitude on the number of cycles to the crack initiation was analyzed. Values of the fatigue properties of the blade material according to Baumel–Seeger and Muralidharan methods were calculated. The influence of both the notch radius and values of the UTS of the blade material on the fatigue behavior of the structure was also considered. In the last part of work, the finite element results were compared with the results of an experimental vibration HCF tests performed for the compressor blades.