<Emphasis Type="Italic">In-Situ</Emphasis> Synthesis of Cu/Cr-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Nanocomposite by Mechanical Alloying and Heat Treatment

In this article, a novel method has been used to prepare a copper matrix nanocomposite containing Cu-10 wt pct Cr-10 wt pct Al₂O₃ by heat treatment of the mechanically activated Cu, Al, and Cr₂O₃ powder mixture. Structural evolutions were investigated using the X-ray diffraction (XRD) technique. The microstructure of samples was examined using scanning electron microscopy (SEM). It was found that during the milling process, Cu(Al) solid solution and Cu₉Al₄ phase were formed as the intermediate products, and therefore, Al activity was decreased. Hence, the reduction of Cr₂O₃ with Al was prevented during the ball milling stage. Further heat treatment carried out under argon atmosphere at 900 °C for 8 hours resulted in completion of Cr₂O₃ reduction by Al.     

Effect of CaO-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-MgO slags on the formation of MgO-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> inclusions in ferritic stainless steel

A thermodynamic equilibrium between the Fe-16Cr melts and the CaO-Al₂O₃-MgO slags at 1823 K as well as the morphology of inclusions was investigated to understand the formation behavior of the MgO-Al₂O₃ spinel-type inclusions in ferritic stainless steel. The calculated and observed activities of magnesium in Fe-16Cr melts are qualitatively in good agreement with each other, while those of aluminum in steel melts exhibit some discrepancies with scatters. In the composition of molten steel investigated in this study, the log (X _MgO/X _{Al 2}O₃) of the inclusions linearly increases by increasing the log [a _Mg/a _Al ² ·a _O ² ] with the slope close to unity. In addition, the relationship between the log (X _MgO/X _{Al 2}O₃) of the inclusions and the log (a _MgO/a _{Al 2}O₃) of the slags exhibits the linear correlation with the slope close to unity. The compositions of the inclusions are relatively close to those of the slags, viz. the MgO-rich magnesia-spinel solid solutions were formed in the steel melts equilibrated with the highly basic slags saturated by CaO or MgO. The spinel inclusions nearly saturated by MgO were observed in the steel melts equilibrated with the slags doubly saturated by MgO and MgAl₂O₄. The spinel and the Al₂O₃-rich alumina-spinel solid solutions were formed in the steel melts equilibrated with the slags saturated by MgAl₂O₄ and MgAl₂O₄-CaAl₂O₄ phases, respectively. The apparent modification reaction of MgO to the magnesium aluminate inclusions in steel melts equilibrated with the highly basic slags would be constituted by the following reaction steps: (1) diffusion of aluminum from bulk to the metal/MgO interface, (2) oxidation of the aluminum to the Al³⁺ ions at the metal/intermediate layer interface, (3) diffusion of Al³⁺ ions and electrons through the intermediate layer, and (4) magnesium aluminate (MgAl₂O₄ spinel, for example) formation by the ionic reaction.     

Development of Wear-Resistant Cu-10Cr-3Ag Electrical Contacts with Nano-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Dispersion by Mechanical Alloying and High Pressure Sintering

Cu-10Cr-3Ag (wt pct) alloy with nanocrystalline Al₂O₃ dispersion was prepared by mechanical alloying and consolidated by high pressure sintering at different temperatures. Characterization by X-ray diffraction and scanning electron microscopy or transmission electron microscopy shows the formation of nanocrystalline matrix grains of about 40 nm after 25 hours of milling with nanometric (<20 nm) Al₂O₃ particles dispersed in it. After consolidation by high pressure sintering (8 GPa at 400 °C to 800 °C), the dispersoids retain their ultrafine size and uniform distribution, while the alloyed matrix undergoes significant grain growth. The hardness and wear resistance of the pellets increase significantly with the addition of nano-Al₂O₃ particles. The electrical conductivity of the pellets without and with nano-Al₂O₃ dispersion is about 30 pct IACS (international annealing copper standard) and 25 pct IACS, respectively. Thus, mechanical alloying followed by high pressure sintering seems a potential route for developing nano-Al₂O₃ dispersed Cu-Cr-Ag alloy for heavy duty electrical contact.     

Thermodynamics on the formation of spinel (MgO·Al<Subscript>2</Subscript>O<Subscript>3</Subscript>) inclusion in liquid iron containing chromium

The stability diagram of MgO, spinel solid solution (MgO·(Al _X Cr_1−X )₂O₃), and sesquioxide solid solution ((Al _Y Cr_1−Y )₂O₃) as a function of Mg, Al, and O contents at a constant chromium content (18 mass pct) in liquid iron is drawn at 1873 K. The interaction parameters between Mg and other solutes (Al, Cr, Ni, Ti, Si, and C) are determined by the experimental method, which assures equilibrium between Mg vapor and liquid iron, were applied to calculate the diagram. Titanium deoxidation is not recommended for the prevention of spinel formation, because Ti accelerates Mg dissolution from refractory or slag due to its high affinity for Mg (e _Mg ^Ti = − 0.64). The standard Gibbs free energies of formation for the three inclusions (periclase, spinel, and sesquioxide solid solutions) and the tielines between two solid solutions were calculated with the aid of the regular solution model and the thermochemical F*A*C*T database computing system, respectively. The phase stability regions and oxygen content in steel for the current Fe-Mg-Al-Cr (18 mass pct)-O system are compared with those of the previous non-Cr system. Detailed information on the spinel composition according to Mg and Al contents is also available from the present stability diagram.     

Wettability of Mn<Subscript>x</Subscript>Si<Subscript>y</Subscript>O<Subscript>z</Subscript> by Liquid Zn-Al Alloys

The wettability of Mn_xSi_yO_z by liquid Zn-Al alloys was investigated to obtain basic information on the coating properties of high-strength steels with surface oxides in the hot-dip galvanizing process. In this study, the contact angles of liquid Zn-Al alloys (Al concentrations were 0.12 and 0.23 wt pct) on four different Mn_xSi_yO_z oxides, namely MnO, MnSiO₃, Mn₂SiO₄, and SiO₂, were measured with the dispensed drop method. The contact angle did not change across time. With an increasing Al concentration, the contact angle was slightly decreased for MnO and Mn₂SiO₄, but there was no change for MnSiO₃ and SiO₂. With an increasing SiO₂ content, the contact angle gradually increased by 54 wt pct to form MnSiO₃, and for pure SiO₂ substrate, the contact angle decreased again. Consequently, the MnSiO₃ substrate showed the worst wettability among the four tested oxide substrates.     

Effects of FeO and CaO/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Ratio in Slag on the Cleanliness of Al-Killed Steel

The slag composition plays a critical role in the formation of inclusions and the cleanliness of steel. In this study, the effects of FeO content and the C/A (CaO/Al₂O₃) ratio in the slag on the formation of inclusions were investigated based on a 10-minute slag–steel reaction in a MgO crucible. The FeO content in the top slag was shown to have a significant effect on the formation of MgO·Al₂O₃ spinel inclusions, and critical content exists; when the initial FeO content in the slag was less than 2 pct, MgO·Al₂O₃ spinel inclusions formed, and the T.O (total oxygen) was 20 ppm; when the initial FeO content in the slag was more than 4 pct, only Al₂O₃ inclusions were observed and the T.O was 50 ppm. It was clarified that the main source of Mg for the MgO·Al₂O₃ spinel inclusion formation was the top slag rather than the MgO crucible. In addition, the cleanliness of the steel increased as the initial FeO content in the top slag decreased. As regards the effects of the C/A ratio, the MgO amount in the observed inclusions gradually increased, whereas the T.O content decreased gradually with the increasing C/A ratio. Slag with a composition close to the CaO-saturated region had the best effect on the inclusion absorption.     

Effect of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Concentration on Density and Structure of (CaO-SiO<Subscript>2</Subscript>)-xAl<Subscript>2</Subscript>O<Subscript>3</Subscript> Slag

The effect of Al₂O₃ concentration on the density and structure of CaO-SiO₂-Al₂O₃ slag was investigated at multiple Al₂O₃ mole percentages and at a fixed CaO/SiO₂ ratio of 1. The experiments were conducted in the temperature range of 2154 K to 2423 K (1881 °C to 2150 °C) using the aerodynamic levitation technique. In order to understand the relationship between density and structure, structural analysis of the silicate melts was carried out using Raman spectroscopy. The density of each slag sample investigated in this study decreased linearly with increasing temperature. When the Al₂O₃ content was less than 15 mole pct, density decreased with increasing Al₂O₃ content due to the coupling of Si (Al), whereas above 20 mole pct density of the slag increased due to the role of Al³⁺ ion as a network modifier.     

Amphoteric behavior of alumina in viscous flow and structure of CaO-SiO<Subscript>2</Subscript> (-MgO)-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> slags

The viscosity of CaO-SiO₂ (-MgO)-Al₂O₃ slags was measured to clarify the effects of Al₂O₃ and MgO on the structure and viscous flow of molten slags at high temperatures. Furthermore, the infrared spectra of the quenched slags were analyzed to understand the structural role of Al₂O₃ in the polymerization or depolymerization of silicate network. The Al₂O₃ behaves as an amphoteric oxide with the composition of slags; that is, the alumina behaves as a network former up to about 10 mass pct Al₂O₃, while it acts as a network modifier, in parts, in the composition greater than 10 mass pct Al₂O₃. This amphoteric role of Al₂O₃ in the viscous flow of molten slags at the Newtonian flow region was diminished by the coexistence of MgO. The effect of Al₂O₃ on the viscosity increase can be understood based on an increase in the degree of polymerization (DOP) by the incorporation of the [AlO₄]-tetrahedra into the [SiO₄]-tetrahedral units, and this was confirmed by the infrared (IR) spectra of the quenched slags. The influence of alumina on the viscosity decrease can be explained on the basis of a decrease in the DOP by the increase in the relative fraction of the [AlO₆]-octahedral units. The relative intensity of the IR bands for the [SiO₄]-tetrahedra with low NBO/Si decreased, while that of the IR bands for [SiO₄]-tetrahedra with high NBO/Si increased with increasing Al₂O₃ content greater than the critical point, i.e., about 10 mass pct in the present systems. The variations of the activity coefficient of slag components with composition indirectly supported those of viscosity and structure of the aluminosilicate melts.     

Effect of MgO on Liquidus Temperatures in the ZnO-“FeO”-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-CaO-SiO<Subscript>2</Subscript>-MgO System in Equilibrium with Metallic Iron

The phase equilibria in the ZnO-“FeO”-Al₂O₃-CaO-SiO₂-MgO system have been determined experimentally in equilibrium with metallic iron. Synthetic slags were equilibrated at a high temperature, quenched, and then the compositions of the phases in equilibrium were measured using electron probe X-ray microanalysis. Pseudoternary sections of the form ZnO-“FeO”-(Al₂O₃ + CaO + SiO₂) for CaO/SiO₂ = 0.71, (CaO + SiO₂)/Al₂O₃ = 5 and fixed MgO concentrations of 2, 4, and 6 wt pct have been constructed. Wustite (Fe²⁺,Mg,Zn)O and spinel (Fe²⁺,Mg,Zn)O·(Al,Fe³⁺)₂O₃ are the major primary phases in the temperature and composition ranges investigated. The liquidus temperatures are increased by 140 K in the wustite primary phase field and by 70 K in the spinel primary phase field with the addition of 6 wt pct MgO in the slag. The partitioning of MgO and ZnO between the solid and liquid phases has been discussed.     

Evaluating the Diffusion Coefficient of Sulfur in Low-Silica CaO-SiO<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Slag

The chemical diffusion coefficient of sulfur in the ternary slag of composition 51.5 pct CaO-9.6 pct SiO₂-38.9 pct Al₂O₃ slag was measured at 1680 K, 1700 K, and 1723 K (1403 °C, 1427 °C, and 1450 °C) using the experimental method proposed earlier by the authors. The P_\textS2 P_{{{\text{S}}_{2} }} and P_\textO2 P_{{{\text{O}}_{2} }} pressures were calculated from the Gibbs energy of the equilibrium reaction between CaO in the slag and solid CaS. The density of the slag was obtained from earlier experiments. Initially, the order of magnitude for the diffusion coefficient was taken from the works of Saito and Kawai but later was modified so that the concentration curve for sulfur obtained from the program was in good fit with the experimental results. The diffusion coefficient of sulfur in 51.5 pct CaO-9.6 pct SiO₂-38.9 pct Al₂O₃ slag was estimated to be in the range 3.98 to 4.14 × 10⁻⁶ cm²/s for the temperature range 1680 K to 1723 K (1403 °C to 1450 °C), which is in good agreement with the results available in literature     

Fabrication of Al-3 Wt pct Mg matrix composites reinforced with Al2O3 and SiC particulates by the pressureless infiltration technique

In Al-3 wt pct Mg/Al₂O_3p (or SiC _p ) composites fabricated by the pressureless infiltration method, the infiltration behavior of molten metal, the mechanical properties, and the interfacial reactions were investigated. The spontaneous infiltration of the molten Al-3 wt pct Mg alloy into the powder bed occurred at a relatively low temperature (700 °C for 1 hour under a nitrogen atmosphere). Spontaneous infiltration of the molten metal is related to the formation of Mg₃N₂ by the reaction of Mg and nitrogen. The tensile strength and 0.2 pct offset yield strength and elongation tend to decrease with increasing infiltration temperature and time, because of an increased interfacial reaction. In Al-3Mg/Al₂O₃ composites, MgAl₂O₄ was observed at interfaces between Al₂O₃ and the matrix, as well as at oxide films of the Al powder surface. In addition, MgO was observed at interfaces between Al₂O₃ and the matrix. On the other hand, Al₄C₃ was formed at interfaces between SiC and the matrix in Al-3Mg/SiC composites. In addition, MgAl₂O₄ was observed as a reaction product at the interfaces between oxide films of SiC and the matrix, as well as at oxide films of the Al powder surface. Since the Si released as a result of the interfacial reaction is combined with Mg, age hardening can occur by the precipitation of Mg₂Si via T6 treatment.     

Effect of heat treatments on <Emphasis Type="Italic">In-Situ</Emphasis> Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiAl<Subscript>3</Subscript> composites produced from squeeze casting of TiO<Subscript>2</Subscript>/A356 composites

In-situ Al₂O₃/TiAl₃ intermetallic matrix composites were fabricated via squeeze casting of TiO₂/A356 composites heated in the temperature range from 700 °C to 780 °C for 2 hours. The phase transformation in TiO₂/A356 composites employing various heat-treatment temperatures (700 °C to 780 °C) was studied by means of differential thermal analysis (DTA), microhardness, scanning electron microscopy (SEM), electron probe microanalysis (EPMA), and X-ray diffraction (XRD). From DTA, two exothermic peaks from 600 °C to 750 °C were found in the TiO₂/A356 composites. The XRD showed that Al₂O₃ and TiAl₃ were the primary products after heat treatment of the TiO₂/A356 composite. The fabrication of in-situ Al₂O₃/TiAl₃ composites required 33 vol pct TiO₂ in Al and heat treatment in the range from 750 °C to 780 °C. The hardness (HV) of the in-situ Al₂O₃/TiAl₃ composites (1000 HV) was superior to that of nonreacted TiO₂/A356 composites (200 HV). However, the bending strength decreased from 685 MPa for TiO₂/A356 composites to 250 MPa for Al₂O₃/TiAl₃ composites. It decreased rapidly because pores occurred during the formation of Al₂O₃ and TiAl₃. The activation energy of the formation of Al₂O₃ and TiAl₃ from TiO₂ and A356 was determined to be about 286 kJ/mole.     

Influence of CaF<Subscript>2</Subscript> and Li<Subscript>2</Subscript>O on the Viscous Behavior of Calcium Silicate Melts Containing 12 wt pct Na<Subscript>2</Subscript>O

Understanding the viscous behavior of silica-based molten fluxes is essential in maintaining the reliability of steel casting operations and in preventing breakouts. In particular, high concentrations of aluminum in recently developed transformation induced plasticity (TRIP) and twinning induced plasticity (TWIP) steels tend to promote reduction of silica in the mold fluxes that result in the formation of alumina, which in turn increases the viscosity. To counteract this effect, significant amounts of fluidizers such as CaF₂ and Li₂O are required to ensure that mold fluxes have acceptable lubrication and heat transfer characteristics. The viscous behavior of the slag system based on CaO-SiO₂-12 wt pct Na₂O with various concentrations of CaF₂ and Li₂O has been studied using the rotating spindle method to understand the effects on the viscosity with these additives. CaF₂ additions up to 8 wt pct were effective in decreasing the viscosity by breaking the network structure of molten fluxes, but CaF₂ concentrations above this level had a negligible effect on viscosity. Li₂O additions up to 2 wt pct were also effective in decreasing the viscosity, but the effect was comparatively negligible above 2 wt pct. Using Fourier transform infrared (FTIR) analysis of as-quenched slag samples, it was concluded that the viscosity was controlled more effectively by changing the larger complex silicate structures of rings and chains than by changing the amounts of simpler dimers and monomers.     

Phase Equilibria in the TiO2-Rich Part of the TiO2-CaO-SiO2-10 Wt Pct Al2O3-5 Wt Pct MgO System at 1773 K

Metallurgical and Materials Transactions B - The phase equilibria of the TiO2-CaO-SiO2-10&nbsp;wt&nbsp;pct Al2O3-5&nbsp;wt&nbsp;pct MgO system in the TiO2-rich part were...     

Thermodynamics of Arsenic in FeOx-CaO-SiO<Subscript>2</Subscript> Slags

The distribution of arsenic between calcium ferrite slag and liquid silver (wt pct As in slag/ wt pct As in liquid silver) with 22 wt pct CaO and between iron silicate slag with 24 wt pct SiO₂ and calcium iron silicate slags was measured at 1573 K (1300 °C) under a controlled CO-CO₂-Ar atmosphere. For the calcium ferrite slags, a broad range of oxygen partial pressure (10^–11 to 0.21 atm) was covered, whereas for the silicate slags, the oxygen partial pressure was varied from 10^–9 to 3.1 × 10^–7 atm. The measured relations between the distribution ratio of As and the oxygen partial pressure indicates that the oxidation state of arsenic in these slags is predominantly As³⁺ or AsO_1.5. The measured distribution ratio of arsenic between the calcium ferrite slag and the liquid silver was about an order of magnitude higher than that of the iron silicate slag. In addition, an increasing concentration of SiO₂ in the calcium-ferrite-based melts resulted in decreases in the distribution of arsenic into the slag. Through the use of measured equilibrium data on the arsenic content of the metal and slag in conjunction with the composition dependent on the activity of arsenic in the metal, the activity of AsO_1.5 in the slags was deduced. These activity data on AsO_1.5 show a negative deviation from the ideal behavior in these slags.     

Distribution Ratios of Phosphorus Between CaO-FeO-SiO<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/Na<Subscript>2</Subscript>O/TiO<Subscript>2</Subscript> Slags and Carbon-Saturated Iron

In order to effectively enhance the efficiency of dephosphorization, the distribution ratios of phosphorus between CaO-FeO-SiO₂-Al₂O₃/Na₂O/TiO₂ slags and carbon-saturated iron (\( L_{\text{P}}^{\text{Fe-C}} \)) were examined through laboratory experiments in this study, along with the effects of different influencing factors such as the temperature and concentrations of the various slag components. Thermodynamic simulations showed that, with the addition of Na₂O and Al₂O₃, the liquid areas of the CaO-FeO-SiO₂ slag are enlarged significantly, with Al₂O₃ and Na₂O acting as fluxes when added to the slag in the appropriate concentrations. The experimental data suggested that \( L_{\text{P}}^{\text{Fe-C}} \) increases with an increase in the binary basicity of the slag, with the basicity having a greater effect than the temperature and FeO content; \( L_{\text{P}}^{\text{Fe-C}} \) increases with an increase in the Na₂O content and decrease in the Al₂O₃ content. In contrast to the case for the dephosphorization of molten steel, for the hot-metal dephosphorization process investigated in this study, the FeO content of the slag had a smaller effect on \( L_{\text{P}}^{\text{Fe-C}} \) than did the other factors such as the temperature and slag basicity. Based on the experimental data, by using regression analysis, \( \log L_{\text{P}}^{\text{Fe-C}} \) could be expressed as a function of the temperature and the slag component concentrations as follows:

$$ \begin{aligned} \log L_{\text{P}}^{\text{Fe-C}} & = 0.059({\text{pct}}\;{\text{CaO}}) + 1.583\log ({\text{TFe}}) - 0.052\left( {{\text{pct}}\;{\text{SiO}}_{2} } \right) - 0.014\left( {{\text{pct}}\;{\text{Al}}_{2} {\text{O}}_{3} } \right) \\ \, & \quad + 0.142\left( {{\text{pct}}\;{\text{Na}}_{2} {\text{O}}} \right) - 0.003\left( {{\text{pct}}\;{\text{TiO}}_{2} } \right) + 0.049\left( {{\text{pct}}\;{\text{P}}_{2} {\text{O}}_{5} } \right) + \frac{13{,}527}{T} - 9.87. \\ \end{aligned} $$