基于液氮吸附实验的煤层夹矸孔隙结构特征研究

煤层夹矸存在孔隙,具有吸附气体的能力。为研究沁水盆地新景矿煤层夹矸孔隙特征,选择8#煤层夹矸和15#煤层夹矸进行液氮静态吸附法实验研究。根据实验结果对新景煤矿8#煤层夹矸和15#煤层夹矸孔隙结构特征中的比表面积、孔径、孔径占比进行分析。结果表明:新景8#煤层夹矸主要以微孔和小孔为主,微孔和小孔占总孔比的92%以上,新景15#煤层夹矸主要由微孔、小孔和中孔为主,微孔、小孔占67%,中孔占到32%左右。微孔、小孔孔径大小与比表面积和吸附量有较强的相关性。     

Phenomenon of methane driven caused by hydraulic fracturing in methane-bearing coal seams

The methane concentration of the return current will always be enhanced to a certain degree when hydraulic fracturing with bedding drilling is implemented to a gassy coal seam in an underground coal mine. The methane in coal seam is driven out by hydraulic fracturing. Thus, the phenomenon is named as methane driven effect of hydraulic fracturing. After deep-hole hydraulic fracturing at the tunneling face of the gassy coal seam, the coal methane content exhibits a ‘‘low-high-low" distribution along excavation direction in the following advancing process, verifying the existence of methane driven caused by hydraulic fracturing in methane-bearing coal seam. Hydraulic fracturing causes the change of pore-water and methane pressure in surrounding coal. The uneven distribution of the pore pressure forms a pore pressure gradient. The free methane migrates from the position of high pore(methane) pressure to the position of low pore(methane) pressure. The methane pressure gradient is the fundamental driving force for methane-driven coal seam hydraulic fracturing. The uneven hydraulic crack propagation and the effect of time(as some processes need time to complete and are not completed instantaneously) will result in uneven methane driven. Therefore, an even hydraulic fracturing technique should be used to avoid the negative effects of methane driven; on the other hand, by taking fully advantage of methane driven, two technologies are presented.     

水力压裂煤储层卸压增透技术的适用性分析

水力压裂煤储层技术在不同矿区应用过程中受不同煤体破坏类型和围压条件的影响,其卸压增透效果差异性较大.为了明确该项技术的井下适用条件,优化其实施工艺,切实提高煤层瓦斯抽采率,通过分析和总结河南省不同矿区实际煤储层的水力压裂试验数据资料发现,水力压裂增透技术对Ⅰ,Ⅱ破坏类型煤体的增透效果比较明显,而在Ⅲ,Ⅳ,Ⅴ破坏类型的松软煤层中适用性则具有一定的局限性,具有压裂范围小、裂缝闭合快、增透效果不明显等特点.所得结论对于选择合理的水力压裂储层并进一步优化完善高效预抽本煤层瓦斯技术具有一定的指导意义.     

煤层注水促抽瓦斯及其影响因素的数值模拟

为有效预防煤矿瓦斯灾害,获取煤层注水促抽瓦斯的合理参数,以常村煤矿2103工作面为例,依据多相渗流理论,采用Fluent软件的VOF模型及多孔介质模型耦合求解,对煤层注水促抽瓦斯技术及其影响因素进行数值模拟,并将模拟结果应用于现场,对比分析数值模拟与现场实测数据,二者基本吻合.研究结果表明:煤层瓦斯含量以注水孔为中心径向逐步降低,以抽采孔为中心径向逐步升高;注水前抽采阶段,随着抽采时间的增加,抽采范围逐渐增大,抽采孔瓦斯流量先快速下降,后逐步缓慢降低;注水促抽阶段,随着注水时间的增加,注水范围逐渐增大,注水流量逐步降低,煤层瓦斯含量缓慢升高,抽采孔瓦斯流量逐渐增加;注水后抽采阶段,随着抽采时间的增加,压力水覆盖范围持续增大,煤层瓦斯含量逐渐降低,抽采孔瓦斯流量逐渐减小.注水时机、注水时间、注水压力、注水方式、布置方式及钻孔间距是影响煤层注水促抽瓦斯效果的6个主要因素.瓦斯正常抽采20 d后,按照一注一抽方式及5 m间距布置注抽钻孔,在8 MPa煤层注水压力下间歇注水10 d,煤层注水促抽瓦斯效果较好.     

Reservoir reconstruction technologies for coalbed methane recovery in deep and multiple seams

Multiple coal seams widely develop in the deep Chinese coal-bearing strata. Ground in situ stress and coal seam gas pressure increase continuously with the increase of the mining depth, and coal and gas outburst disasters become increasingly severe. When the coal is very deep, the gas content and pressure will elevate and thus coal seams tends to outburst-prone seams. The safety and economics of exploited firstmined coal seams are tremendously restricted. Meanwhile, the multiple seams occurrence conditions resulted in different methane pressure systems in the coal-bearing strata, which made the reservoir reconstruction of coal difficult. Given the characteristics of low saturation, low permeability, strong anisotropy and soft coal of Chinese coal seams, a single hydraulic fracturing surface well for reservoir reconstruction to pre-drain the coalbed methane(CBM) of multiple seams concurrently under the different gas pressure systems has not yet gained any breakthroughs. Based on analyses of the main features of deep CBM reservoirs in China, current gas control methods and the existing challenges in deep and multiple seams, we proposed a new technology for deep CBM reservoir reconstruction to realize simultaneous high-efficiency coal mining and gas extraction. In particular, we determined the first-mined seam according to the principles of effectiveness and economics, and used hydraulic fracturing surface well to reconstruct the first-mined seam which enlarges the selection range of the first-mined seam. During the process of mining first-mined seam, adjacent coal seams could be reconstructed under the mining effect which promoted high-efficiency pressure relief gas extraction by using spatial and comprehensive gas drainage methods(combination of underground and ground CBM extraction methods). A typical integrated reservoir reconstruction technology, ‘‘One well for triple use", was detailed introduced and successfully applied in the Luling coal mine. The application showed that the proposed technology could effectively promote coal mining safety and simultaneously high-efficiency gas extraction.     

我国煤矿瓦斯抽放存在的问题及对策探讨

通过对我国煤矿瓦斯抽放现状的分析,指出预抽时间短、钻孔工程量不足、封孔质量差、抽放系统不匹配、管理不到位是造成目前我国煤矿瓦斯抽放率偏低的主要原因,并结合国内外的最新研究进展,探讨了解决上述问题的技术对策。     

Fissure evolution and evaluation of pressure-relief gas drainage in the exploitation of super-remote protected seams

Based on nonlinearity contact theory and the geological structure of the Xieqiao Coal Mine in the newly developed Huainan coal field, rock movements, mining fissures and deformation of overlying strata were simulated by using the interface unit of FLAC3D to evaluate the pressure-relief gas drainage in the exploitation of super-remote protected seams. The simulation indicates that the height of the water flowing fractured zone is 54 m in the overlying strata above the protective layer. The maximum relative swelling deformation of the C 13 coal seam is 0.232%,while the mining height is 3.0 m and the distance from the B8 roof to the C13 floor is 129 m, which provides good agreement with a similar experiment and in situ results. The feasibility of exploitation of a super-remote protective coal seam and the performance of the pressure-relief gas drainage in a super-remote protected layer are evaluated by comparisons with practice projects. It demonstrates that the relieved gas in the super-remote protected layers could be better drained and it is feasible to exploit the B8 coal seam before the C13 super-remote protected coal seam. The method is applicable for the study of rock movements, mining fissures and deformation of the overburden, using the interface unit to analyze the contact problems in coal mines.     

A case study of gas drainage to low permeability coal seam

Gas drainage at low gas permeability coal seam is a main barrier affecting safety and efficient production in coal mines. Therefore, the research and application of drainage technology at low permeability coal seam is a key factor for gas control of coal mine. In order to improve the drainage effect, this paper establishes a three-dimensional solid-gas-liquid coupling numerical model, and the gas drainage amounts of different schemes are examined inside the overburden material around the goaf. The Yangquan mine area is selected for the case study, and the gas movement regularity and emission characteristics are analyzed in detail, as well as the stress and fissure variation regularity. Also examinations are the released gas movement, enrichment range and movement regularity during coal extraction. Moreover, the gas drainage technology and drainage parameters for the current coal seam are studied. After measuring the gas drainage flow in-situ, it is concluded that the technology can achieve notable drainage results, with gas drainage rate increase by 30%–40% in a low permeability coal seam.     

改善平沟煤矿16~#煤层润湿性的研究

煤层注水现已成为矿井预防重大事故的综合性安全技术措施.煤层注水是以解决采煤工作面煤尘问题而发展起来的,后来又逐渐应用于预防冲击地压,提高瓦斯抽放效等方面.煤体注水的好处很多,但是不同煤质会对注水造成不同的影响.针对平沟16#煤润湿性差的现象进行了研究,并提出了添加尼诺尔、十二烷基苯磺酸钠和2种表面活性剂改善其煤体的润湿性,以提高煤体注水的效果.     

Undesorbable residual gas in coal seams and its influence on gas drainage

The definition of ‘‘residual gas" can be found in different scenarios, such as the ‘‘fast" and ‘‘slow" desorption methods of measuring gas content and the sorption hysteresis test and gas management of coal mines, however, its meaning varies a lot in different contexts. The main aim of this paper is to discuss the existence of truly undesorbable residual gas in coal seam conditions and its impacts on sorption model and gas drainage efficiency. We believe the undesorbable residual gas does exist due to the observation of the extended slow desorption test and the sorption hysteresis test. The origin of undesorbable residual gas may be because of the inaccessible(closed or semi-closed) pores. Some gas molecules produced during coalification are stored in these inaccessible pores, since the coal is relatively intact in the coal seam condition, these gas molecules cannot escape during natural desorption and then create the undesorbable residual gas. Based on the existing adsorption models, we propose the improved desorption versions by taking into consideration the role of residual gas. By numerically simulating a gas drainage case, the gas contents after different drainage times are studied to understand the influence of residual gas content on gas drainage. The results indicate that the influence starts to be obvious even when the total gas content is at a high level, and the impact becomes more and more apparent with increasing drainage time. Our study shows that the existence of residual gas will impede the gas drainage and the total amount of recoverable coal seam methane may be less than expected.     

近距离突出煤层群瓦斯治理技术优化的研究

近距离突出煤层群工作面受上下邻近煤层卸压瓦斯的影响,致使回采工作面瓦斯涌出量大、工作面回风隅角及回风巷中的甲烷传感器频繁报警,瓦斯治理消耗大量的人力、物力和时间,严重制约了矿井的安全生产。通过对几种瓦斯治理方案进行分析论证,得出将整个煤层群作为一个治理单元,统筹考虑,将煤层厚度、瓦斯含量相对较小的弱突出煤层作为关键保护层,配合打钻进行立体式抽采,实现上下递进保护,最大限度地抽采邻近煤层的卸压瓦斯的方案。现场实践结果表明,保护层工作面在回采期间瓦斯抽采率高达90%以上,回风隅角瓦斯浓度降至0.6%以下,回风巷风流中瓦斯浓度降至0.2%以下,工作面月平均回采长度由原来的120 m提高至200 m。同时,从根本上解决了被保护层工作面回采期间瓦斯带来的安全威胁。     

Measurement of overburden failure zones in close-multiple coal seams mining

In the Kaiping Coal field, mining of five coal seams, located within 80 m in the Kailuan Group, #5, #7, #8,#9 and #12 coal seam, is difficult due to small interburden thickness, concentrated stress distributions,high coal seam metamorphism, and complex geological conditions. By using the ZTR12 geological penetration radar(GPR) survey combined with borehole observations, the overburden caving due to mining of the five coals seams was measured. The development characteristics of full-cover rock fractures after mining were obtained from the GPR scan, which provides a measurement basis for the control of rock strata in close multiple coal seam mining. For the first time, it was found that the overburden caving pattern shows a periodic triangular caved characteristic. Furthermore, it is proposed that an upright triangular collapsed pile masonry and an inverted triangular with larger fragments piled up alternately appear in the lower gob. The research results show that the roof structure formed in the gob area can support the key overlying strata, which is beneficial to ensure the integrity and stability of the upper coal seams in multiple-seam mining of close coal seams.     

Regional gas drainage techniques in Chinese coal mines

China’s rapid economic development has increased the demand for coal. These results in Chinese coal mines being extended to deeper levels. The eastern Chinese, more economical developed, regions have a long history of coal mining and many coal mines have now started deep mining at a depth from 800 to 1500 m. This increase in mining depth, geostresses, pressures, and gas content of the coal seam complicates geologic construction conditions. Lower permeability and softer coal contribute to increasing numbers of coal and gas outburst, and gas explosion, disasters. A search on effective methods of preventing gas disasters has been provided funds from the Chinese government since 1998. The National Engineering Research Center of Coal Gas Control and the Huainan and Huaibei Mining Group have conducted theoretical and experimental research on a regional gas extraction technology. The results included two important findings. First, grouped coal seams allow adoption of a method where a first, key protective layer is mined to protect upper and lower coal seams by increasing permeability from 400 to 3000 times. Desorption of gas and gas extraction in the protected coal seam of up to 60%, or more, may be achieved in this way. Second, a single seam may be protected by using a dense network of extraction boreholes consisting of cross and along-bed holes. Combined with this is increased use of water that increases extraction of coal seam gas by up to 50%. Engineering practice showed that regional gas drainage technology eliminates regional coal and gas outburst and also enables mining under low gas conditions. These research results have been adopted into the national safety codes of production technology. This paper systematically introduces the principles of the technology, the engineering methods and techniques, and the parameters of regional gas drainage. Engineering applications are discussed.     

平顶山矿区庚_（20）煤层中的“板舌”构造及成因

本文对平顶山二矿、三矿太原组庚切汉层中的“板舌”构过进行了较为详细地描述，分析了其成因，阐明了板舌构造是煤层中顶断底不断的小型逆断层的一种特殊型式。     

Pressure relief, gas drainage and deformation effects on an overlying coal seam induced by drilling an extra-thin protective coal seam

Numerical simulations and field tests were used to investigate the changes in ground stress and deformation of, and gas flow from, a protected coal seam under which an extra-thin coal seam was drilled. The geological conditions were: 0.5 meter min-ing height, 18.5 meter coal seam spacing and a hard limestone/fine sandstone inter-stratum. For these conditions we conclude: 1) the overlying coal-rock mass bends and sinks without the appearance of a caving zone, and 2) the protected coal seam is in the bending zone and undergoes expansion deformation in the stress-relaxed area. The deformation was 12 mm and the relative defor-mation was 0.15%. As mining proceeds, deformation in the protected layer begins as compression, then becomes a rapid expansion and, finally, reaches a stable value. A large number of bed separation crannies are created in the stress-relaxed area and the perme-ability coefficient of the coal seam was increased 403 fold. Grid penetration boreholes were evenly drilled toward the protected coal seam to affect pressure relief and gas drainage. This made the gas pressure decrease from 0.75 to 0.15 Mpa, the gas content de-crease from 13 to 4.66 m3/t and the gas drainage reach 64%.     

Numerical simulation of gas migration into mining-induced fracture network in the goaf

Gas extraction practice has been proven for the clear majority of coal mines in China to be unfavorable using drill holes in the coal seam. Rather, mining-induced fractures in the goaf should be utilized for gas extraction. To study gas migration in mining-induced fractures, one mining face of 10 th Mine in Pingdingshan Coalmine Group in Henan, China, has been selected as the case study for this work. By establishing the mathematical model of gas migration under the influence of coal seam mining, discrete element software UDEC and Multiphysics software COMSOL are employed to model gas migration in mining-induced fractures above the goaf. The results show that as the working face advances, the goaf overburden gradually forms a mining-induced fracture network in the shape of a trapezoid, the size of which increases with the distance of coal face advance. Compared with gas migration in the overburden matrix, the gas flow in the fracture network due to mining is far greater. The largest mining-induced fracture is located at the upper end of the trapezoidal zone, which results in the largest gas flux in the network. When drilling for gas extraction in a mining-induced fracture field, the gas concentration is reduced in the whole region during the process of gas drainage, and the rate of gas concentration drops faster in the fractured zone. It is shown that with gas drainage, the gas flow velocity in the mininginduced fracture network is faster.     

Proactive interburden fracturing using UIS drilling with validation monitoring

A series of gas inrush events occurred during development at Grosvenor Mine resulting in exposure to elevated levels of methane at the production face. A total of 22 gas inrush events occurred, with between15 and 130 m3 of methane released during each event. The presence of an undrained seam in the immediate floor, geotechnical characteristics of the floor, and the stress environment all contributed to these dynamic floor events, while the geological characteristics of the seam below, such as the seam thickness and ash content of 75%, prevented effective predrainage. However, events only occurred in headings mined parallel to the principal horizontal stress direction. In cut-throughs(C/T) perpendicular to the principal stress direction no events occurred, and higher methane levels were observed at the production face. The solution to preventing the gas inrush events involved creating a conduit in the interburden between the mined seam and the seam in the immediate floor to allow the gas to be drained during the development of the headings, as occurred in the cut-throughs(cut-through and cross-cut are regional terms that are analogous). A series of underground inseam(UIS) holes were drilled using the directional drill rig with the aim of fracturing this interburden ahead of the face and promote floor failure to allow the gas to release consistently. The floor fracturing was conducted using water pressure generated from a longwall salvage pump, with the current UIS drilling equipment retrofitted with a series of subs, packers and a fracturing tool. The packers and the fracturing tool were shifted to desired locations along the drilled UIS borehole to achieve the required fracture. The fractures were monitored using a proving hole and with a HYDAC data logger attached to the salvage pack, with the results analysed on the surface to ensure connectivity to the working seam.     

Applicability of surface directional wells for upper Silesia Basin coal seams? drainage ahead of mining

Methods of exploitation drainage, which is presently applied in polish hard coal mines in Upper Silesian Coal Basin (Poland), are not effective enough, high risk of methane hazard can be observed, and production capacity of the mining plant is not fully used. Methane hazard, which may occur during planned coal exploitation, is presented in this paper. Following parameters are taken into consideration in the forecasts: coal extraction parameters, geological and mining conditions, deposit’s methane saturation degree and impact of coal exploitation on the degasification coefficient of the seams, which are under the influence of relaxation zone. This paper presents the results of the analysis aiming to verify applicability of drainage ahead of mining of the coal seams by using surface directional wells. Based on the collected data (coal seams’ structural maps, profiles of the exploratory wells, geological cross-sections), the lab tests of drilling cores and direct wells’ tests, static model of the deposit was constructed and suitable grid of directional wells from the surface was designed. Comparison of forecasted methane emission volume between the two methods is investigated. The results indicated the necessity of performing appropriate deposit’s stimulations in order to increase effectiveness of drainage ahead of mining.     

Layout and support design of a coal roadway in ultra-close multiple-seams

A roadway within ultra-close multiple-seams(RUCMSs) is one of the most difficult supported coal roadways to deal with in underground coal mines. This is usually due to the unknown stress distributions, improper roadway layout, and unreasonable support parameters. In order to solve this support problem and effectively save RUCMSs from frequent and abrupt disasters(such as serious deformation of the surrounding rock, roof cave ins, and coal side collapse), a comprehensive method is adopted here which includes theoretical analysis, numerical simulation, and field monitoring. A mechanical model was constructed to determine the stress distribution in the coal pillar after two sides of a longwall panel had been mined. Based on this model, the horizontal, vertical, and tangential stress equations for the plane below the floor of the upper-left coal pillar were deduced. In addition, a typical coal mine(the Jinggonger colliery, located in Shuozhou city, Shanxi province, China) with an average distance between its 9# and 11# coal seams of less than 8.0 was chosen to conduct research on the proper layout and reasonable support required for a typical coal roadway located within coal seam 11#. Using FLAC3D(Fast Lagrangian Analysis of Continua in 3-Dimensions) numerical software, eight schemes were designed with different horizontal distances(d) between the center lines of the coal pillar and the roadway in the lower coal seam(RLCS). The simulations and detailed analysis indicate that the proper distances required are between 22.5 and 27.5 m. A total of 20 simulation schemes were used to investigate the factors influencing the support provided by the key bolts(bolt length, spacing, distance between two rows, installation angle, and pre-tightening force). The results were analyzed and used to determine reasonable values for the support parameters. Field results show that the stability and strength of the RLCS can be effectively safeguarded using a combination of researched stress distribution characteristics, proper layout of the RLCS, and correct support parameters.     

石门沟煤矿3号煤层瓦斯赋存规律探究

煤层瓦斯质量体积（含量）是煤层瓦斯主要参数之一,是矿井进行瓦斯涌出量预测、煤与瓦斯突出预测和瓦斯抽放设计的重要依据.只有摸清矿井瓦斯赋存规律,才能对采掘面瓦斯抽放制定合理的技术措施.为避免石门沟煤矿瓦斯治理的盲目性,笔者通过分析煤层瓦斯质量体积与埋藏深度的关系,并结合矿井地质构造,研究了煤层瓦斯赋存规律,总结得出石门沟煤矿3号煤层瓦斯质量体积受地质构造控制,在远离地质构造区域,瓦斯质量体积与埋藏深度呈正相关,并推出其关系式,为矿井瓦斯治理提供可靠数据.