CaSc2O4:Eu: A tunable full-color emitting phosphor for white light emitting diodes

We report an intense full-color emission originating from ⁵D_0,1,2,3 to ⁷F_0,1,2,3,4 transitions of Eu³⁺ in CaSc₂O₄ upon 395 nm excitation. The emission spectra vary with increasing Eu³⁺ concentration, demonstrating tunable color coordinates from white to red region in the CIE chromaticity diagram. Considering the relaxation from ⁵D_J to ⁵D_J−1 through cross energy transfer, the Eu³⁺ concentration dependent emission spectra are well simulated based on the analysis of steady state rate equations and the measured lifetimes of the ⁵D_J levels. It is suggested that CaSc₂O₄:Eu³⁺ could be a potential single-phased full-color emitting phosphor for near-ultraviolet InGaN chip pumped white light emitting diodes.     

A red-emitting heavy doped phosphor Li6Y(BO3)3:Eu for white light-emitting diodes

A series of Eu³⁺ activated Li₆Y_1−xEu_x(BO₃)₃ (0.05 ? x ? 1) phosphors were synthesized by solid-state reaction method. The structures and photoluminescent properties of the phosphors were investigated at room temperature. The results of XRD patterns indicate that these phosphors are isotypic to the monoclinic Li₆Gd(BO₃)₃. The excitation spectra indicate that these phosphors can be effectively excited by near UV (370-410 nm) light. The red emission from transition ⁵D₀→⁷F₂ is dominant. The emission spectra exhibit strong red performance (CIE chromaticity coordinates: x = 0.65, y = 0.35), which is due to the ⁵D₀−⁷F_J transitions of Eu³⁺ ions. The relationship between the structure and the photoluminescent properties of the phosphors was studied. The concentration quenching occurs at x ≈ 0.85 under near UV excitation. Li₆Y(BO₃)₃:Eu³⁺ has potential application as a phosphor for white light-emitting diodes.     

Luminescent properties of Ca2BO3Cl:Eu yellow-emitting phosphor for white light-emitting diodes

The Ca₂BO₃Cl:Eu²⁺ phosphor was synthesized by the general high temperature solid-state reaction and an efficient yellow emission under near-ultraviolet and blue excitation was observed. The emission spectrum shows a single intense broad emission band centered at 573 nm, which corresponds to the allowed f-d transition of Eu²⁺. The excitation spectrum is very broad extending from 350 to 500 nm, which is coupled well with the emission of UV LED (350-410 nm) and blue LED (450-470 nm). The measured emission of In-GaN-based Ca₂BO₃Cl:Eu²⁺ LED shows white light to the naked eye with a chromatic coordinate of (0.33, 0.36). The Ca₂BO₃Cl:Eu²⁺ is a very appropriate yellow-emitting phosphor for white LEDs.     

Synthesis and photoluminescence properties of Yb doped Ba5(PO4)3Cl phosphor for white light-emitting diodes

Yb²⁺ ion doped Ba₅(PO₄)₃Cl phosphor was synthesized by solid state reaction. Four distinct absorption bands were observed in the Ultraviolet (UV) light region due to the electronic transitions of Yb²⁺ ion from ¹S₀ ground state to ²F_5/2(t_2g), ²F_5/2(e_g), ²F_7/2(t_2g), and ²F_7/2(e_g) excited states. The main emission wavelength of the phosphor was around 630 nm. The optimized Yb²⁺ ion concentration was 0.2 mol% (λ_exc. = 400 nm). The calculated critical distance was about 8.729 Å and the concentration quenching was observed above 0.2 mol% due to the electric dipole–dipole interaction.     

A novel red phosphor NaLa4(SiO4)3F: Eu

A novel red phosphor NaLa₄(SiO₄)₃F: Eu³⁺ was synthesized by the conventional solid-state reaction at 950 °C for the first time. The luminescence properties of NaLa₄(SiO₄)₃F: Eu³⁺ were investigated, and the critical concentration of the activator concentration (Eu³⁺) was found to be 0.1 mol per formula unit. The phosphor presented red luminescence under the ultraviolet excitation of 254 or 395 nm, attributed to the transitions from ⁵D₀ excited states to ⁷F_J ( J = 0-4) ground states of Eu³⁺ ions. The results indicated that this newly-developed phosphor could find applications in tricolor fluorescent lamp, phosphor-liquid crystal displays and white lighting devices utilizing GaN-based excitation in the near UV.     

Novel blue-emitting phosphor NaMg4(PO4)3:Eu, Ce with energy transfer

A blue-emitting phosphor of NaMg₄(PO₄)₃:Eu²⁺, Ce³⁺ was prepared by a combustion-assisted synthesis method. The phase formation was confirmed by X-ray powder diffraction measurement. Photoluminescence excitation spectrum measurements show that the phosphor can be excited by near UV light from 230 to 400 nm and presents a dominant luminescence band centered at 424 nm due to the 4f⁶5d¹ → 4f⁷ transition of Eu²⁺ ions at room temperature. Effective energy transfer occurs in Ce³⁺/Eu²⁺ co-doped NaMg₄(PO₄)₃ due to large spectral overlap between the emission of Ce³⁺ and excitation of Eu²⁺. Co-doping of Ce³⁺ enhances the emission intensity of Eu²⁺ greatly by transferring its excitation energy to Eu²⁺, and Ce³⁺ plays a role as a sensitizer. Ce³⁺-Eu²⁺ co-doped NaMg₄(PO₄)₃ powders can possibly be applied as blue phosphors in the fields of lighting and display.     

Photoluminescence properties of Eu doped Ba2ZnS3 phosphor for white light emitting diodes

The synthesis and photoluminescence properties of novel Eu²⁺ doped Ba₂ZnS₃ phosphors for white light emitting diodes (LEDs) are reported. Diffuse reflection spectra of Ba₂ZnS₃ host and synthesized phosphors have been measured. The excitation spectra of synthesized phosphors consist of three broad bands between 250 nm and 550 nm and are consistent with the diffuse reflectance spectra. The emission spectra show the characteristic 4f⁶5d¹ → 4f⁷ transition of Eu²⁺ ion and there exists efficient energy transfer from host to Eu²⁺ ions when excited by 350-nm light. The dependence of emission spectra on temperature is also measured; the possible reasons applied to explain the experimental results are also discussed. The fluorescence lifetime of Eu²⁺ in Ba_1.995ZnS₃:0.005Eu²⁺ is measured and the values are 1.49 and 23.4 μs.     

Dynamical processes of energy transfer in red emitting phosphor CaMoO4:Sm, Eu

Upon ⁴K_11/2 excitation of Sm³⁺ at 405 nm, the performance of energy transfer from Sm³⁺ to Eu³⁺ in the red emitting phosphor CaMoO₄:Eu³⁺, Sm³⁺ significantly extends its excitation region for better matching the near-UV LED. Photoluminescence spectra indicate that the energy transfer pathway concerns the relaxation from ⁴K_11/2 to ⁴G_5/2 of Sm³⁺ and subsequent transfer to ⁵D₀ of Eu³⁺ rather than ⁵D₁ of Eu³⁺. The fluorescent decay pattern of Sm³⁺⁴G_5/2 level in CaMoO₄:0.5% Sm³⁺, 2% Eu³⁺ is studied at 77 K based on the Inokuti-Hirayama formula, revealing an electronic dipole-dipole interaction between Sm³⁺ and Eu³⁺. The coefficient for the energy transfer is obtained to be 8.5 × 10⁻⁴⁰ s⁻¹ cm⁶. The fluorescence rise and decay pattern of Eu³⁺⁵D₀ level as Sm³⁺ is only excited at 77 K is well described by the dynamical processes of the energy transfer.     

Yellow-emitting phosphor of Sr3B2O6:Eu for application to white light-emitting diodes

This work focuses on the development of Eu²⁺-doped strontium (Sr)-borate as a yellow-emitting phosphor and its application to the fabrication of white light-emitting diodes (LEDs). Synthesis of Eu²⁺-doped Sr-borate phosphors was finely tuned for obtaining the efficient yellow luminescence through varying host composition, Eu concentration, and firing temperature. The 1300 °C-fired Eu²⁺-doped Sr₃B₂O₆, which was found to be the most efficient candidate to date, was used for white LED fabrication. Their optical properties were evaluated, resulting in warm white lights with CIE chromaticity coordinates of (0.340–0.372, 0.287–0.314) and color rendering indices of 75–77 under the forward currents of 5–40 mA.     

Self-assembled 3D flower-like NaY(MoO4)2:Eu microarchitectures: Hydrothermal synthesis, formation mechanism and luminescence properties

Self-assembled 3D flower-like NaY(MoO₄)₂:Eu³⁺ microarchitectures were successfully synthesized by a glycine-assisted hydrothermal method at 180 °C. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and high resolution transmission electron microscopy (HRTEM) were employed to characterize the as-obtained products. It was found that morphology modulation could be easily realized by changing the time of hydrothermal reaction system. 3D flower-like NaY(MoO₄)₂:Eu³⁺ microarchitectures were formed with 72 h reaction time. The formation mechanism for flower-like architecture was proposed on the basis of a series of time-dependent experiments. The NaY(MoO₄)₂:Eu³⁺ powders obtained can be effectively excited by 396 nm light, and exhibit strong red emission around 615 nm, attributed to the Eu³⁺⁵D₀ → ⁷F₂ transition. An investigation on the photoluminescence (PL) properties of NaY(MoO₄)₂:Eu³⁺ obtained revealed that the luminescence properties were correlated with the morphology and size.     

Electro-deposition of Y2O3:Eu thin film phosphor and its luminescent properties

Y₂O₃:Eu³⁺ red-emitting thin film phosphor was prepared by a two-step process: the cathodical deposition of thin film of yttrium hydroxide and europium hydroxide followed by an annealing process to achieve Eu³⁺ doped Y₂O₃ film. It is found that the atomic content of Eu³⁺ can be well controlled by simply adjusting the volume ratio of Y(NO₃)₃ to Eu(NO₃)₃ solutions. Dependence of the photoluminescence intensity on the atomic content of Eu³⁺ in Y₂O₃ was also studied. The best photoluminescence performance of Y₂O₃:Eu³⁺ thin film phosphor was achieved as atomic content of Eu³⁺ equal to 1.85 at.%.     

YAG:Ce3+, Gd3+ nano-phosphor for white light emitting diodes

YAG:Ce³⁺, Gd³⁺ nano-phosphors were synthesised by the glycothermal method. The X-ray diffraction measurements showed that the samples can be well-crystallised at 600°C. The transition electron microscope showed that the particles have sizes mostly in the range between 35 and 100?nm. The YAG:Ce nano-phosphor had a wide emission band ranging from blue to yellow with a peak at 532?nm, due to the transition from the lowest 5d band to ²F_7/2, ²F_5/2 states of the Ce³⁺ ion. Red-shift of emission peak wavelength from 532 to 568?nm was achieved doping Gd³⁺ ions into the YAG:Ce³⁺ to substitute some Y³⁺ ions. White light emitting diodes (LEDs) were obtained by combining blue LED chip (InGaN-based 460?nm emitting) with (Y_{2.94? x} Ce_0.06Gd _x )Al₅O₁₂ phosphor. As x has the value of 0.8, an intense white LED with good colour rendering of 86 was obtained.     

A yellow-emitting Ca3Si2O7: Eu phosphor for white LEDs

A series of yellow-emitting phosphors based on a silicate host matrix, Ca_3 − xSi₂O₇: xEu²⁺, was prepared by solid-state reaction method. The structure and photoluminescent properties of the phosphors were investigated. The XRD results show that the Eu²⁺ substitution of Ca²⁺ does not change the structure of Ca₃Si₂O₇ host and there is no impurity phase for x < 0.12. The SEM images display that phosphors aggregate obviously and the shape of the phosphor particle is irregular. The EDX results reveal that the phosphors consist of Ca, Si, O, Eu and the concentration of these elements is close to the stoichiometric composition. The Ca_3 − xSi₂O₇: xEu²⁺ phosphors can be excited at a wavelength of 300-490 nm, which is suitable for the emission band of near ultraviolet or blue light-emitting-diode (LED) chips. The phosphors exhibit a broad emission region from 520 to 650 nm and the emission peak centered at 568 nm. In addition, the shape and the position of the emission peak are not influenced by the Eu²⁺ concentration and excitation wavelength. The phosphor for x = 0.045 has the strongest excitation and emission intensity, and the Ca_3 − xSi₂O₇: xEu²⁺ phosphors can be used as candidates for the white LEDs.     

Near UV-based LED fabricated with Ba5SiO4(F,Cl)6:Eu as blue- and green-emitting phosphor

A series of halosilicate phosphor, Ba₅SiO₄(F,Cl)₆:Eu²⁺, were synthesized by a solid state reaction. Excited by 370-nm light, Ba₅SiO₄Cl₆:Eu²⁺ exhibits a broad emission band peaking at 440 nm. Partial substitution of Cl⁻ with F⁻ in the host lattice leads to red-shift in the emission band with centering wavelength from 440 nm to 503 nm. The possible mechanism for the luminescence change was discussed based on the XRD patterns. Blue and green LEDs were fabricated by combination of a 370 nm-emitting near UV chip and the optimal Ba₅SiO₄Cl₆:Eu²⁺ and Ba₅SiO₄(F₃Cl₃):Eu²⁺, respectively. This series of phosphors is considered as a promising blue and green component used in fabrication of near UV-based white LEDs.     

Polarized spectroscopic properties of Ho ions in NaLa(MoO4)2 crystal

A Ho³⁺-doped NaLa(MoO₄)₂ single crystal was grown by the Czochralski method. The polarized absorption spectra, polarized fluorescence spectra, and fluorescence decay curves of the crystal were measured at room temperature. The spontaneous emission probabilities, radiative lifetimes, and fluorescence branching ratios of the typical fluorescence multiplets of Ho³⁺ ions were calculated. The polarized stimulated emission and gain cross-sections of the ⁵I₇ → ⁵I₈ transition were obtained. The results show that the Ho³⁺:NaLa(MoO₄)₂ crystal is a promising gain medium for tunable and ultrashort pulse lasers operating around 2.0 μm.     

Growth and spectral properties of Cr:KAl(MoO4)2 crystal

The Cr³⁺:KAl(MoO₄)₂ single crystal was grown by top seeding solution growth method (TSSG). Based on the absorption and emission spectra, the crystal field strength Dq, the Racah parameters B and C, the effective phonon energy ?ω and the Huang-Rhys factor S were calculated: Dq = 1494.8 cm^− 1, B = 585.5 cm^− 1 and C = 3049 cm^− 1, ?ω = 373.8 cm^− 1 and the Huang-Rhys factor S = 3.74, respectively. The value Dq/B = 2.55 indicates that Cr³⁺ ion occupies the strong crystal field site in KAl(MoO₄)₂ crystal. A comparison of crystal field parameters for Cr³⁺:KAl(MoO₄)₂ with other Cr³⁺-doped crystals was presented. The results of spectral measurement show that Cr³⁺:KAl(MoO₄)₂ may be a potential candidate for broadband laser applications.     

Synthesis and luminescent properties of LaPO4:Eu microspheres

LaPO₄:Eu³⁺ microspheres were synthesized, using LaCl₃, EuCl₃ and (NH₄)₂HPO₄ as starting materials. The morphology, formation mechanism, and luminescent property of samples were systemically studied. X-ray diffraction (XRD) and infrared spectroscopy (IR) show that LaPO₄:Eu³⁺ microspheres have a pure monoclinic phase. Cetyltrimethyl ammonium bromide (CTAB) usually forms spherical micelles above a critical micelle concentration, which plays an important role in the formation of LaPO₄:Eu³⁺ microspheres. The excitation spectrum of LaPO₄:Eu³⁺ microspheres consists of several sharp lines due to the direct excitation of the Eu³⁺ cations from the ground state to higher levels of the 4f-manifold. The emission intensity of microspheres is higher than irregular particles because of the lowlier surface area. The lifetimes of Eu³⁺ ions in the LaPO₄:Eu³⁺ microspheres are determined to be 2.41 ms.     

Thermoluminescence properties of Ce-doped LiSr4(BO3)3 phosphor

Borates LiSr₄(BO₃)₃ were synthesized by high-temperature solid-state reaction. The thermoluminescence (TL) and some of the dosimetric characteristics of Ce³⁺-activated LiSr₄(BO₃)₃ were reported. The TL glow curve is composed of only one peak located at about 209 °C between room temperature and 500 °C. The optimum Ce³⁺ concentration is 1 mol% to obtain the highest TL intensity. The TL kinetic parameters of LiSr₄(BO₃)₃:0.01Ce³⁺ were studied by the peak shape method. The TL dose response is linear in the protection dose ranging from 1 mGy to 1 Gy. The three-dimensional thermoluminescence emission spectra were also studied, peaking at 441 and 474 nm due to the characteristic transition of Ce³⁺.     

Sr3.5Mg0.5Si3O8Cl4: Eu bluish-green-emitting phosphor for NUV-based LED

Sr₄Si₃O₈Cl₄:Eu²⁺ and Sr_3.5Mg_0.5Si₃O₈Cl₄:Eu²⁺ phosphors were prepared by a conventional solid state reaction (SS). Excited by 370 nm near-ultraviolet light, the phosphors show an efficient bluish-green wide-band emission centering at 484 nm, which originates from the 4f5d¹ → 4f⁷ transition of Eu²⁺ ion. The excitation spectra of the phosphors are a broad band extending from 250 nm to 400 nm. Mg²⁺-codoping greatly enhances the bluish-green emission of the phosphors. An LED was fabricated by coating the Sr_3.5Mg_0.5Si₃O₈Cl₄:0.08Eu²⁺ phosphor onto an ~ 370 nm-emitting InGaN chip. The LED exhibits bright bluish-green emission under a forward bias of 20 mA. The results indicate that Sr_3.5Mg_0.5Si₃O₈Cl₄:0.08Eu²⁺ is a candidate as a bluish-green component for fabrication of NUV-based white LEDs.